Searched full:routed (Results 1 – 25 of 71) sorted by relevance
123
| /Documentation/ABI/testing/ |
| D | sysfs-bus-pci-drivers-ehci_hcd | 10 high-speed device is plugged in, the connection is routed
12 is plugged in, the connection is routed to the companion
17 connection to be routed to the companion controller.
19 file causes connections on that port to be routed to the
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-bcm6328.txt | 207 /* USB link/activity routed to USB LED */
213 /* INET activity routed to INET LED */
219 /* EPHY0 link routed to EPHY0 LED */
225 /* EPHY1 link routed to EPHY1 LED */
231 /* EPHY2 link routed to EPHY2 LED */
237 /* EPHY3 link routed to EPHY3 LED */
259 /* USB/INET link/activity routed to USB LED */
265 /* EPHY0/1/2/3 link routed to EPHY0 LED */
287 /* USB link/act and INET act routed to USB LED */
293 /* EPHY3 link routed to EPHY0 LED */
[all …]
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | interrupts.txt | 13 which the interrupts are routed; see section 2 below for details.
20 interrupts are routed and contains a single phandle referring to the interrupt
116 interrupts routed to them, so that they can wakeup the SoC from suspend. These
|
| D | riscv,cpu-intc.txt | 7 Every interrupt is ultimately routed through a hart's HLIC before it
15 interrupts connect all other device interrupts to the HLIC, which are routed
|
| D | qcom,pdc.txt | 11 wakeup capabilities of their device interrupts routed through the PDC, must
28 need to be configured for wakeup capable GPIOs routed to
|
| D | brcm,bcm7038-l1-intc.txt | 14 peripheral IRQs to be routed to any CPU
|
| D | brcm,bcm6345-l1-intc.txt | 13 peripheral IRQs to be routed to any CPU
|
| /Documentation/devicetree/bindings/clock/ |
| D | lpc1850-ccu.txt | 22 Shall contain a list of phandles for the base clocks routed
26 Shall contain a list of names for the base clock routed
|
| D | lpc1850-creg-clk.txt | 9 The 32 kHz can also be routed to other peripherials to enable low
|
| /Documentation/devicetree/bindings/thermal/ |
| D | ti_soc_thermal.txt | 20 the talert signal is routed to;
23 line the tshut signal is routed to. The informed GPIO will
|
| D | rcar-gen3-thermal.txt | 24 - interrupts : interrupts routed to the TSC (must be 3).
|
| /Documentation/media/v4l-drivers/ |
| D | imx.rst | 121 containing each virtual channel that are routed to CSIs or video
124 On i.MX6 solo/dual-lite, all four virtual channel buses are routed to
128 On i.MX6 Quad, virtual channel 0 is routed to IPU1-CSI0 (after selected
130 and IPU2-CSI0, respectively, and virtual channel 3 is routed to
165 When the direct source pad is routed to the ipuX_ic_prp entity, frames
169 When the direct source pad is routed to the ipuX_vdic entity, the VDIC
175 source pad is routed to a capture device node, with a node name of the
313 Input capture requires hardware support. A VSYNC signal must be routed
370 routed to a capture device node, with a node name of the format
385 pad from ipuX_ic_prp, and a single source pad. The source pad is routed
[all …]
|
| /Documentation/devicetree/bindings/connector/ |
| D | usb-connector.txt | 73 1. Micro-USB connector with HS lines routed via controller (MUIC):
84 2. USB-C connector attached to CC controller (s2mm005), HS lines routed
86 DisplayPort video lines are routed to the connector via SS mux in USB3 PHY.
|
| D | samsung,usb-connector-11pin.txt | 27 Micro-USB connector with HS lines routed via controller (MUIC) and MHL lines
|
| /Documentation/ia64/ |
| D | irq-redir.rst | 59 The IRQ is routed to the CPU with lowest XTP register value, the
65 manner. IRQs will be routed only to the selected target CPUs. Check
|
| /Documentation/devicetree/bindings/mailbox/ |
| D | omap-mailbox.txt | 11 interrupt lines. An output interrupt line is routed to an interrupt controller
25 routed to different processor sub-systems on DRA7xx as they are routed through
29 all these clusters are multiplexed and routed to different processor subsystems
|
| /Documentation/devicetree/bindings/net/ |
| D | icplus-ip101ag.txt | 17 interrupts are not routed outside the PHY in this mode.
|
| /Documentation/sound/hd-audio/ |
| D | controls.rst | 71 When this enum control is enabled, the headphone output is routed
119 When this enum control is enabled, the headphone output is routed
|
| /Documentation/networking/ |
| D | ipvs-sysctl.txt | 255 realservers so that they are routed as if they originate from the
256 director. Otherwise they are routed as if they are forwarded by the
260 of a packet originating from a director is routed differently to a
|
| /Documentation/media/uapi/dvb/ |
| D | net.rst | 30 virtual ``dvb?_?`` network interfaces, and will be controlled/routed via
|
| /Documentation/devicetree/bindings/arm/bcm/ |
| D | brcm,bcm2835.txt | 17 early model B with I2C0 rather than I2C1 routed to the expansion header
|
| /Documentation/devicetree/bindings/phy/ |
| D | qcom,usb-8x16-phy.txt | 73 // D+/D- lines: 1 - Routed to HUB, 0 - Device connector
|
| /Documentation/sound/cards/ |
| D | cmipci.rst | 31 disabled. Otherwise no signal will be routed to the rear speakers.
50 playback should be routed there as default. If not, there is a
178 SPDIF input is routed to DAC.
|
| /Documentation/devicetree/bindings/arm/omap/ |
| D | crossbar.txt | 14 - ti,max-crossbar-sources: Maximum number of crossbar sources that can be routed.
|
| /Documentation/devicetree/bindings/soc/mediatek/ |
| D | pwrap.txt | 14 The signals of these pins are routed over the SPI bus using the pwrap
|
123