Searched full:selected (Results 1 – 25 of 321) sorted by relevance
12345678910>>...13
| /Documentation/devicetree/bindings/mips/cavium/ |
| D | bootbus.txt | 55 - cavium,wait-mode: Optional. If present, wait mode (WAITM) is selected.
57 - cavium,page-mode: Optional. If present, page mode (PAGEM) is selected.
62 - cavium,ale-mode: Optional. If present, ALE mode is selected.
64 - cavium,sam-mode: Optional. If present, SAM mode is selected.
66 - cavium,or-mode: Optional. If present, OR mode is selected.
|
| /Documentation/usb/ |
| D | gadget_printer.rst | 116 Printer is NOT Selected
121 To set printer to Selected/On-line::
123 # prn_example -selected
126 To set printer to Not Selected/Off-line::
187 fputs("-selected Set the selected status to selected.\n", stderr);
188 fputs("-not_selected Set the selected status to NOT selected.\n",
429 printf(" Printer is Selected\n");
431 printf(" Printer is NOT Selected\n");
481 } else if (!strcmp(argv[i], "-selected")) {
|
| /Documentation/devicetree/bindings/clock/ti/ |
| D | mux.txt | 7 parents, one of which can be selected as output. This clock does not
17 register value selected parent clock
26 register value selected clock parent
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 69 selected as FPS0, FPS1 or FPS2.
76 selected as FPS0, FPS1 or FPS2.
89 FPS source is selected as FPS0, FPS1 or
97 FPS source is selected as FPS0, FPS1 or
|
| D | fsl,imx27-pinctrl.txt | 33 have any effect unless GPIO function is selected. A/B/C_IN are output
44 B. GPIO function should be selected if this is configured.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | max8998.txt | 32 - max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from
36 - max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from
45 for buck1 regulator that can be selected using dvs gpio.
49 for buck2 regulator that can be selected using dvs gpio.
|
| /Documentation/ia64/ |
| D | serial.rst | 106 - Multiple UARTs selected as EFI console devices. EFI and
107 elilo use all selected devices, but Linux uses only one.
108 Make sure only one UART is selected in the EFI console
112 selected as EFI console device. EFI uses the MP as a
113 console device even when it isn't explicitly selected.
|
| D | irq-redir.rst | 21 first non-zero bit is the selected CPU. This format has been kept for
65 manner. IRQs will be routed only to the selected target CPUs. Check
|
| /Documentation/media/uapi/dvb/ |
| D | video_types.rst | 76 VIDEO_SOURCE_MEMORY /* If this source is selected, the stream
83 VIDEO_SOURCE_MEMORY is selected the stream comes from the application
198 video_displayformat_t display_format;/* selected cropping mode */
205 selected source for the video stream. It can come either from the
208 Finally, display_format corresponds to the selected cropping mode in
|
| D | video-slowmotion.rst | 62 selected.
83 - Mode VIDEO_SOURCE_MEMORY not selected.
|
| D | video-fast-forward.rst | 62 selected.
83 - Mode VIDEO_SOURCE_MEMORY not selected.
|
| D | video-fwrite.rst | 59 This system call can only be used if VIDEO_SOURCE_MEMORY is selected
78 - Mode VIDEO_SOURCE_MEMORY not selected.
|
| D | audio-fwrite.rst | 60 This system call can only be used if AUDIO_SOURCE_MEMORY is selected
79 - Mode AUDIO_SOURCE_MEMORY not selected.
|
| D | video-select-source.rst | 66 selected, the data is fed to the video device through the write command.
74 VIDEO_SOURCE_MEMORY /* If this source is selected, the stream
|
| D | audio_data_types.rst | 35 AUDIO_SOURCE_MEMORY is selected the stream comes from the application
56 The audio channel selected via AUDIO_CHANNEL_SELECT is determined by
|
| /Documentation/filesystems/ |
| D | fuse-io.txt | 8 The direct-io mode can be selected with the FOPEN_DIRECT_IO flag in the
20 writeback-cache mode may be selected by the FUSE_WRITEBACK_CACHE flag in the
|
| /Documentation/media/uapi/v4l/ |
| D | io.rst | 20 :ref:`write() <func-write>` function is automatically selected after opening a
30 application does not directly receive the image data. It is selected by
|
| /Documentation/devicetree/bindings/sound/ |
| D | cs35l34.txt | 35 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel),
37 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right
|
| /Documentation/devicetree/bindings/mmc/ |
| D | marvell,xenon-sdhci.txt | 81 If this property is selected, transfers will bypass PHY.
96 Only valid when "marvell,armada-3700-sdhci" is selected.
98 If "sd" is selected, SoC PHY PAD is set as 3.3V at the beginning and is
100 If "fixed-1-8v" is selected, SoC PHY PAD is fixed 1.8V, such as for eMMC.
|
| /Documentation/fb/ |
| D | arkfb.rst | 36 There are two 4 bpp modes. First mode (selected if nonstd == 0) is mode with
37 packed pixels, high nibble first. Second mode (selected if nonstd == 1) is mode
|
| D | vt8623fb.rst | 33 There are two 4 bpp modes. First mode (selected if nonstd == 0) is mode with
34 packed pixels, high nibble first. Second mode (selected if nonstd == 1) is mode
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-led-trigger-usbport | 8 selected for the USB port trigger. Selecting ports makes trigger
|
| D | sysfs-driver-hid-corsair | 15 Description: Get/set the current selected profile. Values are from 1 to 3.
|
| /Documentation/devicetree/bindings/rtc/ |
| D | dallas,ds1390.txt | 8 - trickle-resistor-ohms : Selected resistor for trickle charger
|
| D | ti,bq32k.txt | 8 - trickle-resistor-ohms : Selected resistor for trickle charger
|
12345678910>>...13