| /Documentation/devicetree/bindings/powerpc/4xx/ |
| D | cpm.txt | 24 - standby : specifier consist of one cell. For each
26 in CPM will be set on standby and
31 restored on resume. Note, for standby
34 standby only class 2 and 3 units are set.
50 standby = <0xfeff0000>;
|
| /Documentation/admin-guide/pm/ |
| D | sleep-states.rst | 42 This state can be used on platforms without support for :ref:`standby <standby>`
49 Standby section in Sleep States That Can Be Supported
81 contents. All of the steps carried out when entering :ref:`standby <standby>`
98 relative to :ref:`suspend-to-idle <s2idle>` and :ref:`standby <standby>` and it
165 In particular, the strings "disk", "freeze" and "standby" represent the
167 :ref:`standby <standby>` sleep states, respectively. The string "mem"
182 :ref:`standby <standby>` and :ref:`suspend-to-RAM <s2ram>`,
238 into the :ref:`standby <standby>` state (the strings to write to the control
239 files in that case are "standby" or "shallow" and "mem", respectively) if that
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | mt9m001.txt | 15 - standby-gpios: GPIO handle which is connected to the standby pin of the chip.
30 standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
|
| D | mt9v032.txt | 24 - standby-gpios: GPIO handle which is connected to the standby pin of the chip.
|
| D | aptina,mt9v111.txt | 21 - standby-gpios: low power state control signal, pin name "STANDBY".
|
| D | toshiba,et8ek8.txt | 20 is in hardware standby mode when the signal is in the low state.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | mcp16502-regulator.txt | 44 regulator-state-standby {
63 regulator-state-standby {
82 regulator-state-standby {
101 regulator-state-standby {
118 regulator-state-standby {
133 regulator-state-standby {
|
| D | regulator.yaml | 145 regulator-state-(standby|mem|disk):
148 sub-nodes for regulator state in Standby, Suspend-to-RAM, and
149 Suspend-to-DISK modes. Equivalent with standby, mem, and disk Linux
|
| /Documentation/devicetree/bindings/arm/msm/ |
| D | qcom,idle-state.txt | 8 * Standby
13 Standby: Standby does a little more in addition to architectural clock gating.
18 hierarchy to enter standby states, when all cpus are idle. An interrupt brings
20 cache hierarchy is also out of standby, and then the cpu is allowed to resume
31 state. Retention may have a slightly higher latency than Standby.
|
| /Documentation/networking/ |
| D | net_failover.rst | 12 standby slave netdevs that get registered via the generic failover
16 original paravirtual interface is registered as 'standby' slave netdev and
18 netdev. Both 'standby' and 'failover' netdevs are associated with the same
28 virtio-net accelerated datapath: STANDBY mode
74 'standby' and 'primary' netdevs respectively.
76 Live Migration of a VM with SR-IOV VF & virtio-net in STANDBY mode
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio-xgene-sb.txt | 1 APM X-Gene Standby GPIO controller bindings
3 This is a gpio controller in the standby domain. It also supports interrupt in
7 | X-Gene standby |
20 - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller
|
| /Documentation/hwmon/ |
| D | inspur-ipsps1.rst | 76 standby, when set to standby, PSU will
77 automatically switch between standby
|
| D | tc74.rst | 23 Currently entering low power standby mode is not supported.
|
| D | dme1737.rst | 94 in0: +5VTR (+5V standby) 0V - 6.64V
99 in5: VTR (+3.3V standby) 0V - 4.38V
109 in5: VTR (+3.3V standby) 0V - 4.38V
114 in0: +5VTR (+5V standby) 0V - 6.64V
119 in5: VTR (+3.3V standby) 0V - 4.38V
129 in5: VTR (+3.3V standby) 0V - 4.38V
|
| D | menf21bmc.rst | 44 in3_input +5V Standby input voltage
|
| /Documentation/devicetree/bindings/clock/ |
| D | renesas,cpg-mssr.txt | 1 * Renesas Clock Pulse Generator / Module Standby and Software Reset
4 and MSSR (Module Standby and Software Reset) blocks are intimately connected,
10 1. Module Standby, providing a Clock Domain to control the clock supply
59 power-managed through Module Standby should refer to the CPG device
|
| /Documentation/devicetree/bindings/media/ |
| D | samsung-s5c73m3.txt | 24 - standby-gpios : specifier of GPIO connected to the STANDBY pin;
80 standby-gpios = <&gpm0 1 1>;
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | adi,ad7606.yaml | 57 standby-gpios:
60 to place the AD7606 into one of two power-down modes, Standby mode or
134 standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-regulator | 44 standby
56 "fast", "normal", "idle", and "standby" are all detailed
135 'standby'
278 the system is suspended to standby, for voltage regulators
311 standby, for regulators implementing suspend mode
347 state when suspended to standby, for regulators implementing
|
| /Documentation/devicetree/bindings/usb/ |
| D | usb4604.txt | 11 (1 for HUB mode, 2 for STANDBY mode)
|
| D | usb3503.txt | 17 (1 for HUB mode, 2 for STANDBY mode)
|
| /Documentation/devicetree/bindings/rtc/ |
| D | brcm,brcmstb-waketimer.txt | 4 ability to wake up the system from low-power suspend/standby modes.
|
| /Documentation/devicetree/bindings/sound/ |
| D | ti,tas6424.txt | 9 - standby-gpios: GPIO used to shut the TAS6424 down.
|
| /Documentation/devicetree/bindings/arm/freescale/ |
| D | fsl,imx7ulp-pm.txt | 11 Standby modes for either Cortex family. Run, Wait, and Stop are the
|
| /Documentation/s390/ |
| D | qeth.rst | 27 STATE={active|standby|inactive}
|