Searched full:tolerance (Results 1 – 25 of 25) sorted by relevance
| /Documentation/power/ |
| D | pm_qos_interface.rst | 100 state latency tolerance (in microseconds) and the third one is for PM QoS flags.
103 The target values of resume latency and active state latency tolerance are
189 Active state latency tolerance
198 If there is a latency tolerance control mechanism for a given device available
204 Whenever the effective latency tolerance changes for the device, its
207 latency tolerance requirements for the device is empty, the callback is expected
208 to switch the underlying hardware latency tolerance control mechanism to an
212 automatically updating the device's latency tolerance in response to its power
214 be done in the autonomous latency tolerance control mode.
218 Then, user space can use that attribute to specify its latency tolerance
[all …]
|
| /Documentation/misc-devices/ |
| D | ad525x_dpot.txt | 7 settings. Access to the factory programmed tolerance is also provided, but
15 Each dpot device will have a set of eeprom, rdac, and tolerance files. How
22 The tolerance files are the read-only factory programmed tolerance settings
|
| /Documentation/hwmon/ |
| D | w83792d.rst | 145 via thermal_cruise# file. The tolerance# file serves to create T +- tolerance
147 remains below the thermal_cruise# +- tolerance# value. Once the temperature
148 exceeds the high limit (T+tolerance), the fan will be turned on with a
156 limit (T-tolerance), the fan speed will be fixed at the current speed because
168 temperature region (sf2_point@_fan# +- tolerance#) it will cause fans to run
194 tolerance[1-3]
|
| D | nct6775.rst | 186 Temperature step tolerance.
198 Target temperature tolerance, unit millidegree Celsius
234 Target speed tolerance
258 Temperature tolerance, unit millidegree Celsius
261 Temperature tolerance for critical temperature,
|
| D | w83793.rst | 89 predefined value, within a tolerance margin. So if tempX_input >
92 the PWM value. If the temperature is within the tolerance range, the PWM
|
| D | w83l786ng.rst | 65 tolerance[1-2]
|
| D | nsa320.rst | 58 reasonable tolerance.
|
| D | ds1621.rst | 80 A second thing is that, during extensive testing, Tout showed a tolerance
|
| D | w83791d.rst | 142 temp[1-3]_tolerance temperature tolerance for Thermal Cruise mode.
|
| D | w83627ehf.rst | 178 tolerance, unit millidegree Celsius (range 0 - 15000)
|
| /Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra20-hsuart.txt | 36 Baud Rate tolerance:
37 Standard UART devices are expected to have tolerance for baud rate error by
39 Tegra186 chip has a known hardware issue. UART Rx baud rate tolerance level
|
| /Documentation/devicetree/bindings/cpufreq/ |
| D | cpufreq-dt.txt | 19 - voltage-tolerance: Specify the CPU voltage tolerance in percentage.
|
| /Documentation/filesystems/ |
| D | btrfs.txt | 5 features while focusing on fault tolerance, repair and easy administration.
|
| D | ntfs.txt | 30 fault-tolerance, encryption or journalling) and very limited, but safe, write
33 For fault tolerance and raid support (i.e. volume and stripe sets), you can
|
| /Documentation/x86/x86_64/ |
| D | machinecheck.rst | 51 Tolerance level. When a machine check exception occurs for a non
55 normal kernel locking rules. The tolerance level configures
|
| D | boot-options.rst | 51 tolerance levels:
|
| /Documentation/media/uapi/rc/ |
| D | lirc-get-rec-resolution.rst | 46 tolerance value.
|
| /Documentation/devicetree/bindings/gpio/ |
| D | sgpio-aspeed.txt | 9 - Support reset tolerance option for each output port
|
| /Documentation/ABI/testing/ |
| D | sysfs-devices-power | 229 contains the PM QoS active state latency tolerance limit for the
234 but hardware should not be allowed to set the latency tolerance
241 latency tolerance requirements from the kernel side.
|
| D | sysfs-platform-dfl-port | 46 Description: Read-write. Read or set AFU latency tolerance reporting value.
|
| D | sysfs-bus-usb | 168 USB 3.0 devices may optionally support Latency Tolerance
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | ads7846.txt | 53 ti,debounce-tol Tolerance used for filtering (u16).
|
| /Documentation/devicetree/bindings/devfreq/ |
| D | exynos-bus.txt | 53 - exynos,voltage-tolerance: the percentage value for bus voltage tolerance
|
| /Documentation/devicetree/bindings/regulator/ |
| D | regulator.yaml | 60 reach the target voltage, plus/minus whatever tolerance the board
|
| /Documentation/networking/ |
| D | bonding.txt | 555 tolerance.
574 This mode provides fault tolerance. The primary
587 This mode provides load balancing and fault tolerance.
592 interfaces. This mode provides fault tolerance.
1615 Bonding Mode: fault-tolerance (active-backup)
|