| /arch/sh/kernel/cpu/sh4/ |
| D | setup-sh7760.c | 34 MFI, ADC, CMT, enumerator
70 INTC_VECT(ADC, 0xf80), INTC_VECT(CMT, 0xfa0),
99 0, MFI, 0, 0, 0, 0, ADC, CMT, } },
113 MFI, 0, ADC, CMT } },
|
| /arch/arm64/boot/dts/allwinner/ |
| D | sun50i-a64-sopine-baseboard.dts | 201 "AIF1 Slot 0 Left ADC", "Left ADC",
202 "AIF1 Slot 0 Right ADC", "Right ADC",
|
| D | sun50i-a64-teres-i.dts | 308 "AIF1 Slot 0 Left ADC", "Left ADC",
309 "AIF1 Slot 0 Right ADC", "Right ADC",
|
| D | sun50i-a64-pinebook.dts | 329 "AIF1 Slot 0 Left ADC", "Left ADC",
330 "AIF1 Slot 0 Right ADC", "Right ADC",
|
| D | sun50i-a64-pine64.dts | 289 "AIF1 Slot 0 Left ADC", "Left ADC",
290 "AIF1 Slot 0 Right ADC", "Right ADC",
|
| D | sun50i-a64-bananapi-m64.dts | 358 "AIF1 Slot 0 Left ADC", "Left ADC",
359 "AIF1 Slot 0 Right ADC", "Right ADC",
|
| /arch/sh/kernel/cpu/sh3/ |
| D | setup-sh7720.c | 227 ADC, DMAC2, USBFI, CMT, enumerator
253 INTC_VECT(ADC, 0xbe0), INTC_VECT(SCIF0, 0xc00),
271 { 0xA4080000UL, 0, 16, 4, /* IPRF */ { ADC, DMAC2, USBFI, CMT } },
|
| /arch/arm/boot/dts/ |
| D | cros-adc-thermistors.dtsi | 4 * children of the IIO based ADC.
|
| D | at91-sama5d4ek.dts | 47 /*atmel,adc-ts-wires = <4>;*/ /* Set up ADC touch screen */
48 status = "okay"; /* Enable ADC IIO support */
|
| D | imx6qdl-apalis.dtsi | 335 /* 3.25 MHz ADC clock speed */
337 /* 12-bit ADC */
339 /* internal ADC reference */
341 /* ADC converstion time: 80 clocks */
363 /* forbid to use ADC channels 3-0 (touch) */
|
| D | imx6qdl-colibri.dtsi | 276 /* 3.25 MHz ADC clock speed */
278 /* 12-bit ADC */
280 /* internal ADC reference */
282 /* ADC converstion time: 80 clocks */
304 /* forbid to use ADC channels 3-0 (touch) */
|
| D | exynos4412-odroidu3.dts | 69 /* Nothing connected to ADC inputs, keep it disabled */
|
| D | qcom-msm8660.dtsi | 73 * These channels from the ADC are simply hardware monitors.
74 * That is why the ADC is referred to as "HKADC" - HouseKeeping
75 * ADC.
|
| D | at91-vinco.dts | 38 status = "okay"; /* Enable ADC IIO support */
|
| D | rk3066a-bqcurie2.dts | 61 /* VOL+ comes somehow thru the ADC */
|
| D | tegra30-colibri.dtsi | 851 /* 3.25 MHz ADC clock speed */
862 /* 12-bit ADC */
864 /* internal ADC reference */
866 /* ADC converstion time: 80 clocks */
|
| D | ls1021a-tsn.dts | 186 * - TI ADS7924 4-channel ADC at 0x49
|
| D | tegra30-apalis.dtsi | 982 /* 3.25 MHz ADC clock speed */
993 /* 12-bit ADC */
995 /* internal ADC reference */
997 /* ADC converstion time: 80 clocks */
|
| D | at91-sama5d2_xplained.dts | 364 * There is no real pinmux for ADC, if the pin
367 * Requesting pins for ADC is GPIO is
|
| D | tegra30-apalis-v1.1.dtsi | 1000 /* 3.25 MHz ADC clock speed */
1011 /* 12-bit ADC */
1013 /* internal ADC reference */
1015 /* ADC converstion time: 80 clocks */
|
| /arch/sh/kernel/cpu/sh4a/ |
| D | setup-sh7763.c | 244 TMU3, TMU4, TMU5, ADC, SSI0, SSI1, SSI2, SSI3, enumerator
286 INTC_VECT(TMU5, 0xe40), INTC_VECT(ADC, 0xe60),
309 PCC, 0, 0, ADC, TPU, SIM, SIOF2, SIOF1,
318 { 0xffd4000c, 0, 32, 8, /* INT2PRI3 */ { HUDI, DMAC, ADC } },
|
| D | setup-sh7770.c | 347 ADC, enumerator
386 INTC_VECT(ADC, 0xb20),
422 { 0, BBDMAC, ADC, SCIF, SPI, EXBUS_ATA, GFX3D, GFX2D,
435 { 0xffe0001c, 0, 32, 8, /* INT2PRI7 */ { ADC, 0, 0, BBDMAC_0_3 } },
|
| D | setup-sh7734.c | 334 ADC, enumerator
426 INTC_VECT(ADC, 0xE00),
471 ADC,
|
| /arch/sh/ |
| D | Kconfig.cpu | 55 prompt "ADC support"
59 ADC module.
|
| /arch/arm/plat-samsung/ |
| D | Kconfig | 66 # ADC driver
69 bool "ADC common driver support"
72 Core support for the ADC block found in the Samsung SoC systems
177 Compile in platform device definition for ADC controller
|