1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2007-2009 ST-Ericsson AB
4 * Timer COH 901 328, runs the OS timer interrupt.
5 * Author: Linus Walleij <linus.walleij@stericsson.com>
6 */
7 #include <linux/interrupt.h>
8 #include <linux/time.h>
9 #include <linux/timex.h>
10 #include <linux/clockchips.h>
11 #include <linux/clocksource.h>
12 #include <linux/types.h>
13 #include <linux/io.h>
14 #include <linux/clk.h>
15 #include <linux/err.h>
16 #include <linux/irq.h>
17 #include <linux/delay.h>
18 #include <linux/of_address.h>
19 #include <linux/of_irq.h>
20 #include <linux/sched_clock.h>
21
22 /* Generic stuff */
23 #include <asm/mach/map.h>
24 #include <asm/mach/time.h>
25
26 /*
27 * APP side special timer registers
28 * This timer contains four timers which can fire an interrupt each.
29 * OS (operating system) timer @ 32768 Hz
30 * DD (device driver) timer @ 1 kHz
31 * GP1 (general purpose 1) timer @ 1MHz
32 * GP2 (general purpose 2) timer @ 1MHz
33 */
34
35 /* Reset OS Timer 32bit (-/W) */
36 #define U300_TIMER_APP_ROST (0x0000)
37 #define U300_TIMER_APP_ROST_TIMER_RESET (0x00000000)
38 /* Enable OS Timer 32bit (-/W) */
39 #define U300_TIMER_APP_EOST (0x0004)
40 #define U300_TIMER_APP_EOST_TIMER_ENABLE (0x00000000)
41 /* Disable OS Timer 32bit (-/W) */
42 #define U300_TIMER_APP_DOST (0x0008)
43 #define U300_TIMER_APP_DOST_TIMER_DISABLE (0x00000000)
44 /* OS Timer Mode Register 32bit (-/W) */
45 #define U300_TIMER_APP_SOSTM (0x000c)
46 #define U300_TIMER_APP_SOSTM_MODE_CONTINUOUS (0x00000000)
47 #define U300_TIMER_APP_SOSTM_MODE_ONE_SHOT (0x00000001)
48 /* OS Timer Status Register 32bit (R/-) */
49 #define U300_TIMER_APP_OSTS (0x0010)
50 #define U300_TIMER_APP_OSTS_TIMER_STATE_MASK (0x0000000F)
51 #define U300_TIMER_APP_OSTS_TIMER_STATE_IDLE (0x00000001)
52 #define U300_TIMER_APP_OSTS_TIMER_STATE_ACTIVE (0x00000002)
53 #define U300_TIMER_APP_OSTS_ENABLE_IND (0x00000010)
54 #define U300_TIMER_APP_OSTS_MODE_MASK (0x00000020)
55 #define U300_TIMER_APP_OSTS_MODE_CONTINUOUS (0x00000000)
56 #define U300_TIMER_APP_OSTS_MODE_ONE_SHOT (0x00000020)
57 #define U300_TIMER_APP_OSTS_IRQ_ENABLED_IND (0x00000040)
58 #define U300_TIMER_APP_OSTS_IRQ_PENDING_IND (0x00000080)
59 /* OS Timer Current Count Register 32bit (R/-) */
60 #define U300_TIMER_APP_OSTCC (0x0014)
61 /* OS Timer Terminal Count Register 32bit (R/W) */
62 #define U300_TIMER_APP_OSTTC (0x0018)
63 /* OS Timer Interrupt Enable Register 32bit (-/W) */
64 #define U300_TIMER_APP_OSTIE (0x001c)
65 #define U300_TIMER_APP_OSTIE_IRQ_DISABLE (0x00000000)
66 #define U300_TIMER_APP_OSTIE_IRQ_ENABLE (0x00000001)
67 /* OS Timer Interrupt Acknowledge Register 32bit (-/W) */
68 #define U300_TIMER_APP_OSTIA (0x0020)
69 #define U300_TIMER_APP_OSTIA_IRQ_ACK (0x00000080)
70
71 /* Reset DD Timer 32bit (-/W) */
72 #define U300_TIMER_APP_RDDT (0x0040)
73 #define U300_TIMER_APP_RDDT_TIMER_RESET (0x00000000)
74 /* Enable DD Timer 32bit (-/W) */
75 #define U300_TIMER_APP_EDDT (0x0044)
76 #define U300_TIMER_APP_EDDT_TIMER_ENABLE (0x00000000)
77 /* Disable DD Timer 32bit (-/W) */
78 #define U300_TIMER_APP_DDDT (0x0048)
79 #define U300_TIMER_APP_DDDT_TIMER_DISABLE (0x00000000)
80 /* DD Timer Mode Register 32bit (-/W) */
81 #define U300_TIMER_APP_SDDTM (0x004c)
82 #define U300_TIMER_APP_SDDTM_MODE_CONTINUOUS (0x00000000)
83 #define U300_TIMER_APP_SDDTM_MODE_ONE_SHOT (0x00000001)
84 /* DD Timer Status Register 32bit (R/-) */
85 #define U300_TIMER_APP_DDTS (0x0050)
86 #define U300_TIMER_APP_DDTS_TIMER_STATE_MASK (0x0000000F)
87 #define U300_TIMER_APP_DDTS_TIMER_STATE_IDLE (0x00000001)
88 #define U300_TIMER_APP_DDTS_TIMER_STATE_ACTIVE (0x00000002)
89 #define U300_TIMER_APP_DDTS_ENABLE_IND (0x00000010)
90 #define U300_TIMER_APP_DDTS_MODE_MASK (0x00000020)
91 #define U300_TIMER_APP_DDTS_MODE_CONTINUOUS (0x00000000)
92 #define U300_TIMER_APP_DDTS_MODE_ONE_SHOT (0x00000020)
93 #define U300_TIMER_APP_DDTS_IRQ_ENABLED_IND (0x00000040)
94 #define U300_TIMER_APP_DDTS_IRQ_PENDING_IND (0x00000080)
95 /* DD Timer Current Count Register 32bit (R/-) */
96 #define U300_TIMER_APP_DDTCC (0x0054)
97 /* DD Timer Terminal Count Register 32bit (R/W) */
98 #define U300_TIMER_APP_DDTTC (0x0058)
99 /* DD Timer Interrupt Enable Register 32bit (-/W) */
100 #define U300_TIMER_APP_DDTIE (0x005c)
101 #define U300_TIMER_APP_DDTIE_IRQ_DISABLE (0x00000000)
102 #define U300_TIMER_APP_DDTIE_IRQ_ENABLE (0x00000001)
103 /* DD Timer Interrupt Acknowledge Register 32bit (-/W) */
104 #define U300_TIMER_APP_DDTIA (0x0060)
105 #define U300_TIMER_APP_DDTIA_IRQ_ACK (0x00000080)
106
107 /* Reset GP1 Timer 32bit (-/W) */
108 #define U300_TIMER_APP_RGPT1 (0x0080)
109 #define U300_TIMER_APP_RGPT1_TIMER_RESET (0x00000000)
110 /* Enable GP1 Timer 32bit (-/W) */
111 #define U300_TIMER_APP_EGPT1 (0x0084)
112 #define U300_TIMER_APP_EGPT1_TIMER_ENABLE (0x00000000)
113 /* Disable GP1 Timer 32bit (-/W) */
114 #define U300_TIMER_APP_DGPT1 (0x0088)
115 #define U300_TIMER_APP_DGPT1_TIMER_DISABLE (0x00000000)
116 /* GP1 Timer Mode Register 32bit (-/W) */
117 #define U300_TIMER_APP_SGPT1M (0x008c)
118 #define U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS (0x00000000)
119 #define U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT (0x00000001)
120 /* GP1 Timer Status Register 32bit (R/-) */
121 #define U300_TIMER_APP_GPT1S (0x0090)
122 #define U300_TIMER_APP_GPT1S_TIMER_STATE_MASK (0x0000000F)
123 #define U300_TIMER_APP_GPT1S_TIMER_STATE_IDLE (0x00000001)
124 #define U300_TIMER_APP_GPT1S_TIMER_STATE_ACTIVE (0x00000002)
125 #define U300_TIMER_APP_GPT1S_ENABLE_IND (0x00000010)
126 #define U300_TIMER_APP_GPT1S_MODE_MASK (0x00000020)
127 #define U300_TIMER_APP_GPT1S_MODE_CONTINUOUS (0x00000000)
128 #define U300_TIMER_APP_GPT1S_MODE_ONE_SHOT (0x00000020)
129 #define U300_TIMER_APP_GPT1S_IRQ_ENABLED_IND (0x00000040)
130 #define U300_TIMER_APP_GPT1S_IRQ_PENDING_IND (0x00000080)
131 /* GP1 Timer Current Count Register 32bit (R/-) */
132 #define U300_TIMER_APP_GPT1CC (0x0094)
133 /* GP1 Timer Terminal Count Register 32bit (R/W) */
134 #define U300_TIMER_APP_GPT1TC (0x0098)
135 /* GP1 Timer Interrupt Enable Register 32bit (-/W) */
136 #define U300_TIMER_APP_GPT1IE (0x009c)
137 #define U300_TIMER_APP_GPT1IE_IRQ_DISABLE (0x00000000)
138 #define U300_TIMER_APP_GPT1IE_IRQ_ENABLE (0x00000001)
139 /* GP1 Timer Interrupt Acknowledge Register 32bit (-/W) */
140 #define U300_TIMER_APP_GPT1IA (0x00a0)
141 #define U300_TIMER_APP_GPT1IA_IRQ_ACK (0x00000080)
142
143 /* Reset GP2 Timer 32bit (-/W) */
144 #define U300_TIMER_APP_RGPT2 (0x00c0)
145 #define U300_TIMER_APP_RGPT2_TIMER_RESET (0x00000000)
146 /* Enable GP2 Timer 32bit (-/W) */
147 #define U300_TIMER_APP_EGPT2 (0x00c4)
148 #define U300_TIMER_APP_EGPT2_TIMER_ENABLE (0x00000000)
149 /* Disable GP2 Timer 32bit (-/W) */
150 #define U300_TIMER_APP_DGPT2 (0x00c8)
151 #define U300_TIMER_APP_DGPT2_TIMER_DISABLE (0x00000000)
152 /* GP2 Timer Mode Register 32bit (-/W) */
153 #define U300_TIMER_APP_SGPT2M (0x00cc)
154 #define U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS (0x00000000)
155 #define U300_TIMER_APP_SGPT2M_MODE_ONE_SHOT (0x00000001)
156 /* GP2 Timer Status Register 32bit (R/-) */
157 #define U300_TIMER_APP_GPT2S (0x00d0)
158 #define U300_TIMER_APP_GPT2S_TIMER_STATE_MASK (0x0000000F)
159 #define U300_TIMER_APP_GPT2S_TIMER_STATE_IDLE (0x00000001)
160 #define U300_TIMER_APP_GPT2S_TIMER_STATE_ACTIVE (0x00000002)
161 #define U300_TIMER_APP_GPT2S_ENABLE_IND (0x00000010)
162 #define U300_TIMER_APP_GPT2S_MODE_MASK (0x00000020)
163 #define U300_TIMER_APP_GPT2S_MODE_CONTINUOUS (0x00000000)
164 #define U300_TIMER_APP_GPT2S_MODE_ONE_SHOT (0x00000020)
165 #define U300_TIMER_APP_GPT2S_IRQ_ENABLED_IND (0x00000040)
166 #define U300_TIMER_APP_GPT2S_IRQ_PENDING_IND (0x00000080)
167 /* GP2 Timer Current Count Register 32bit (R/-) */
168 #define U300_TIMER_APP_GPT2CC (0x00d4)
169 /* GP2 Timer Terminal Count Register 32bit (R/W) */
170 #define U300_TIMER_APP_GPT2TC (0x00d8)
171 /* GP2 Timer Interrupt Enable Register 32bit (-/W) */
172 #define U300_TIMER_APP_GPT2IE (0x00dc)
173 #define U300_TIMER_APP_GPT2IE_IRQ_DISABLE (0x00000000)
174 #define U300_TIMER_APP_GPT2IE_IRQ_ENABLE (0x00000001)
175 /* GP2 Timer Interrupt Acknowledge Register 32bit (-/W) */
176 #define U300_TIMER_APP_GPT2IA (0x00e0)
177 #define U300_TIMER_APP_GPT2IA_IRQ_ACK (0x00000080)
178
179 /* Clock request control register - all four timers */
180 #define U300_TIMER_APP_CRC (0x100)
181 #define U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE (0x00000001)
182
183 static void __iomem *u300_timer_base;
184
185 struct u300_clockevent_data {
186 struct clock_event_device cevd;
187 unsigned ticks_per_jiffy;
188 };
189
u300_shutdown(struct clock_event_device * evt)190 static int u300_shutdown(struct clock_event_device *evt)
191 {
192 /* Disable interrupts on GP1 */
193 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
194 u300_timer_base + U300_TIMER_APP_GPT1IE);
195 /* Disable GP1 */
196 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
197 u300_timer_base + U300_TIMER_APP_DGPT1);
198 return 0;
199 }
200
201 /*
202 * If we have oneshot timer active, the oneshot scheduling function
203 * u300_set_next_event() is called immediately after.
204 */
u300_set_oneshot(struct clock_event_device * evt)205 static int u300_set_oneshot(struct clock_event_device *evt)
206 {
207 /* Just return; here? */
208 /*
209 * The actual event will be programmed by the next event hook,
210 * so we just set a dummy value somewhere at the end of the
211 * universe here.
212 */
213 /* Disable interrupts on GPT1 */
214 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
215 u300_timer_base + U300_TIMER_APP_GPT1IE);
216 /* Disable GP1 while we're reprogramming it. */
217 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
218 u300_timer_base + U300_TIMER_APP_DGPT1);
219 /*
220 * Expire far in the future, u300_set_next_event() will be
221 * called soon...
222 */
223 writel(0xFFFFFFFF, u300_timer_base + U300_TIMER_APP_GPT1TC);
224 /* We run one shot per tick here! */
225 writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
226 u300_timer_base + U300_TIMER_APP_SGPT1M);
227 /* Enable interrupts for this timer */
228 writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
229 u300_timer_base + U300_TIMER_APP_GPT1IE);
230 /* Enable timer */
231 writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
232 u300_timer_base + U300_TIMER_APP_EGPT1);
233 return 0;
234 }
235
u300_set_periodic(struct clock_event_device * evt)236 static int u300_set_periodic(struct clock_event_device *evt)
237 {
238 struct u300_clockevent_data *cevdata =
239 container_of(evt, struct u300_clockevent_data, cevd);
240
241 /* Disable interrupts on GPT1 */
242 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
243 u300_timer_base + U300_TIMER_APP_GPT1IE);
244 /* Disable GP1 while we're reprogramming it. */
245 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
246 u300_timer_base + U300_TIMER_APP_DGPT1);
247 /*
248 * Set the periodic mode to a certain number of ticks per
249 * jiffy.
250 */
251 writel(cevdata->ticks_per_jiffy,
252 u300_timer_base + U300_TIMER_APP_GPT1TC);
253 /*
254 * Set continuous mode, so the timer keeps triggering
255 * interrupts.
256 */
257 writel(U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS,
258 u300_timer_base + U300_TIMER_APP_SGPT1M);
259 /* Enable timer interrupts */
260 writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
261 u300_timer_base + U300_TIMER_APP_GPT1IE);
262 /* Then enable the OS timer again */
263 writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
264 u300_timer_base + U300_TIMER_APP_EGPT1);
265 return 0;
266 }
267
268 /*
269 * The app timer in one shot mode obviously has to be reprogrammed
270 * in EXACTLY this sequence to work properly. Do NOT try to e.g. replace
271 * the interrupt disable + timer disable commands with a reset command,
272 * it will fail miserably. Apparently (and I found this the hard way)
273 * the timer is very sensitive to the instruction order, though you don't
274 * get that impression from the data sheet.
275 */
u300_set_next_event(unsigned long cycles,struct clock_event_device * evt)276 static int u300_set_next_event(unsigned long cycles,
277 struct clock_event_device *evt)
278
279 {
280 /* Disable interrupts on GPT1 */
281 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
282 u300_timer_base + U300_TIMER_APP_GPT1IE);
283 /* Disable GP1 while we're reprogramming it. */
284 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
285 u300_timer_base + U300_TIMER_APP_DGPT1);
286 /* Reset the General Purpose timer 1. */
287 writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
288 u300_timer_base + U300_TIMER_APP_RGPT1);
289 /* IRQ in n * cycles */
290 writel(cycles, u300_timer_base + U300_TIMER_APP_GPT1TC);
291 /*
292 * We run one shot per tick here! (This is necessary to reconfigure,
293 * the timer will tilt if you don't!)
294 */
295 writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
296 u300_timer_base + U300_TIMER_APP_SGPT1M);
297 /* Enable timer interrupts */
298 writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
299 u300_timer_base + U300_TIMER_APP_GPT1IE);
300 /* Then enable the OS timer again */
301 writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
302 u300_timer_base + U300_TIMER_APP_EGPT1);
303 return 0;
304 }
305
306 static struct u300_clockevent_data u300_clockevent_data = {
307 /* Use general purpose timer 1 as clock event */
308 .cevd = {
309 .name = "GPT1",
310 /* Reasonably fast and accurate clock event */
311 .rating = 300,
312 .features = CLOCK_EVT_FEAT_PERIODIC |
313 CLOCK_EVT_FEAT_ONESHOT,
314 .set_next_event = u300_set_next_event,
315 .set_state_shutdown = u300_shutdown,
316 .set_state_periodic = u300_set_periodic,
317 .set_state_oneshot = u300_set_oneshot,
318 },
319 };
320
321 /* Clock event timer interrupt handler */
u300_timer_interrupt(int irq,void * dev_id)322 static irqreturn_t u300_timer_interrupt(int irq, void *dev_id)
323 {
324 struct clock_event_device *evt = &u300_clockevent_data.cevd;
325 /* ACK/Clear timer IRQ for the APP GPT1 Timer */
326
327 writel(U300_TIMER_APP_GPT1IA_IRQ_ACK,
328 u300_timer_base + U300_TIMER_APP_GPT1IA);
329 evt->event_handler(evt);
330 return IRQ_HANDLED;
331 }
332
333 static struct irqaction u300_timer_irq = {
334 .name = "U300 Timer Tick",
335 .flags = IRQF_TIMER | IRQF_IRQPOLL,
336 .handler = u300_timer_interrupt,
337 };
338
339 /*
340 * Override the global weak sched_clock symbol with this
341 * local implementation which uses the clocksource to get some
342 * better resolution when scheduling the kernel. We accept that
343 * this wraps around for now, since it is just a relative time
344 * stamp. (Inspired by OMAP implementation.)
345 */
346
u300_read_sched_clock(void)347 static u64 notrace u300_read_sched_clock(void)
348 {
349 return readl(u300_timer_base + U300_TIMER_APP_GPT2CC);
350 }
351
u300_read_current_timer(void)352 static unsigned long u300_read_current_timer(void)
353 {
354 return readl(u300_timer_base + U300_TIMER_APP_GPT2CC);
355 }
356
357 static struct delay_timer u300_delay_timer;
358
359 /*
360 * This sets up the system timers, clock source and clock event.
361 */
u300_timer_init_of(struct device_node * np)362 static int __init u300_timer_init_of(struct device_node *np)
363 {
364 unsigned int irq;
365 struct clk *clk;
366 unsigned long rate;
367 int ret;
368
369 u300_timer_base = of_iomap(np, 0);
370 if (!u300_timer_base) {
371 pr_err("could not ioremap system timer\n");
372 return -ENXIO;
373 }
374
375 /* Get the IRQ for the GP1 timer */
376 irq = irq_of_parse_and_map(np, 2);
377 if (!irq) {
378 pr_err("no IRQ for system timer\n");
379 return -EINVAL;
380 }
381
382 pr_info("U300 GP1 timer @ base: %p, IRQ: %u\n", u300_timer_base, irq);
383
384 /* Clock the interrupt controller */
385 clk = of_clk_get(np, 0);
386 if (IS_ERR(clk))
387 return PTR_ERR(clk);
388
389 ret = clk_prepare_enable(clk);
390 if (ret)
391 return ret;
392
393 rate = clk_get_rate(clk);
394
395 u300_clockevent_data.ticks_per_jiffy = DIV_ROUND_CLOSEST(rate, HZ);
396
397 sched_clock_register(u300_read_sched_clock, 32, rate);
398
399 u300_delay_timer.read_current_timer = &u300_read_current_timer;
400 u300_delay_timer.freq = rate;
401 register_current_timer_delay(&u300_delay_timer);
402
403 /*
404 * Disable the "OS" and "DD" timers - these are designed for Symbian!
405 * Example usage in cnh1601578 cpu subsystem pd_timer_app.c
406 */
407 writel(U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE,
408 u300_timer_base + U300_TIMER_APP_CRC);
409 writel(U300_TIMER_APP_ROST_TIMER_RESET,
410 u300_timer_base + U300_TIMER_APP_ROST);
411 writel(U300_TIMER_APP_DOST_TIMER_DISABLE,
412 u300_timer_base + U300_TIMER_APP_DOST);
413 writel(U300_TIMER_APP_RDDT_TIMER_RESET,
414 u300_timer_base + U300_TIMER_APP_RDDT);
415 writel(U300_TIMER_APP_DDDT_TIMER_DISABLE,
416 u300_timer_base + U300_TIMER_APP_DDDT);
417
418 /* Reset the General Purpose timer 1. */
419 writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
420 u300_timer_base + U300_TIMER_APP_RGPT1);
421
422 /* Set up the IRQ handler */
423 ret = setup_irq(irq, &u300_timer_irq);
424 if (ret)
425 return ret;
426
427 /* Reset the General Purpose timer 2 */
428 writel(U300_TIMER_APP_RGPT2_TIMER_RESET,
429 u300_timer_base + U300_TIMER_APP_RGPT2);
430 /* Set this timer to run around forever */
431 writel(0xFFFFFFFFU, u300_timer_base + U300_TIMER_APP_GPT2TC);
432 /* Set continuous mode so it wraps around */
433 writel(U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS,
434 u300_timer_base + U300_TIMER_APP_SGPT2M);
435 /* Disable timer interrupts */
436 writel(U300_TIMER_APP_GPT2IE_IRQ_DISABLE,
437 u300_timer_base + U300_TIMER_APP_GPT2IE);
438 /* Then enable the GP2 timer to use as a free running us counter */
439 writel(U300_TIMER_APP_EGPT2_TIMER_ENABLE,
440 u300_timer_base + U300_TIMER_APP_EGPT2);
441
442 /* Use general purpose timer 2 as clock source */
443 ret = clocksource_mmio_init(u300_timer_base + U300_TIMER_APP_GPT2CC,
444 "GPT2", rate, 300, 32, clocksource_mmio_readl_up);
445 if (ret) {
446 pr_err("timer: failed to initialize U300 clock source\n");
447 return ret;
448 }
449
450 /* Configure and register the clockevent */
451 clockevents_config_and_register(&u300_clockevent_data.cevd, rate,
452 1, 0xffffffff);
453
454 /*
455 * TODO: init and register the rest of the timers too, they can be
456 * used by hrtimers!
457 */
458 return 0;
459 }
460
461 TIMER_OF_DECLARE(u300_timer, "stericsson,u300-apptimer",
462 u300_timer_init_of);
463