Searched refs:operating (Results 1 – 25 of 38) sorted by relevance
12
| /drivers/power/avs/ |
| D | Kconfig | 6 operating voltage of a device in order to optimize (i.e. reduce)
8 At a given operating point the voltage is adapted depending on
|
| /drivers/devfreq/ |
| D | Kconfig | 10 operating frequency based on the device driver's policy.
92 and adjusts the operating frequencies and voltages with OPP support.
106 operating frequencies and voltages with OPP support.
116 It reads Memory Controller counters and adjusts the operating
|
| /drivers/ras/ |
| D | Kconfig | 17 time, i.e. the amount of time a device is actually operating as the
18 percentage of total time it should be operating.
|
| /drivers/mux/ |
| D | Kconfig | 18 The driver supports both operating the three multiplexers in
19 parallel and operating them independently.
|
| /drivers/sfi/ |
| D | Kconfig | 10 for platform firmware to pass information to the operating system
|
| /drivers/hv/ |
| D | Kconfig | 11 Select this option to run Linux as a Hyper-V client operating
|
| /drivers/net/ethernet/davicom/ |
| D | Kconfig | 24 operating with an external PHY.
|
| /drivers/staging/iio/Documentation/dac/ |
| D | max517 | 38 When the operating system goes to a power down state, the Power Down function
|
| /drivers/pnp/ |
| D | Kconfig | 14 are provided to the cards from the BIOS, from the operating system,
|
| /drivers/net/wireless/broadcom/b43legacy/ |
| D | b43legacy.h | 601 bool operating; member
796 return (wl->operating && in b43legacy_is_mode()
|
| D | main.c | 3391 if (wl->operating) in b43legacy_op_add_interface()
3397 wl->operating = true; in b43legacy_op_add_interface()
3427 B43legacy_WARN_ON(!wl->operating); in b43legacy_op_remove_interface()
3431 wl->operating = false; in b43legacy_op_remove_interface()
|
| /drivers/net/wireless/marvell/mwifiex/ |
| D | README | 46 Ap's operating frequency can be specified or even the bssid. If the AP is using
55 The command will be used to join or create an ibss. Optionally, operating frequency,
64 such as SSID, operating frequency, rx/tx packets, signal strength, tx bitrate.
|
| /drivers/usb/typec/ucsi/ |
| D | Kconfig | 8 specification for an interface that allows the operating system to
|
| /drivers/acpi/apei/ |
| D | Kconfig | 16 to the operating system. This improves NMI handling
|
| /drivers/staging/speakup/ |
| D | TODO | 5 Speakup is a kernel based screen review package for the linux operating
|
| /drivers/visorbus/ |
| D | visorchipset.c | 762 state.operating == segment_state_running.operating) in visorbus_device_changestate()
767 state.operating == segment_state_standby.operating) in visorbus_device_changestate()
|
| D | controlvmchannel.h | 61 u16 operating:1; member
|
| /drivers/net/wireless/broadcom/b43/ |
| D | b43.h | 926 bool operating; member
991 return (wl->operating && wl->if_type == type); in b43_is_mode()
|
| /drivers/firewire/ |
| D | Kconfig | 53 operating systems. Multicast support is currently limited.
|
| /drivers/pci/ |
| D | Kconfig | 93 when it is going to be assigned to a guest operating system.
|
| /drivers/net/wireless/ath/ath9k/ |
| D | Kconfig | 95 transmitters operating at frequencies from 300 kHz to 100 GHz.
|
| /drivers/net/ethernet/8390/ |
| D | Kconfig | 179 operating systems. The Linux smc-ultra driver has a work-around for
|
| /drivers/cpufreq/ |
| D | Kconfig.arm | 330 provide dt based operating-points-v2 tables with opp-supported-hw
|
| D | Kconfig.x86 | 279 does not have any safeguards to prevent operating the CPU out of spec
|
| /drivers/firmware/ |
| D | Kconfig | 15 set of operating system-independent software interfaces that are
|
12