Searched refs:starts (Results 1 – 18 of 18) sorted by relevance
| /drivers/staging/pi433/Documentation/ |
| D | pi433.txt | 49 As soon as the predefined RSSI level is met, a receiving cycle starts. Similar
113 fifo_level - transmission starts, if fifo is filled to
115 fifo_not_empty - transmission starts, as soon as there is one
181 If this value is exceeded, a reception cycle starts
|
| /drivers/spi/ |
| D | spi-s3c24xx-fiq.S | 32 @ each entry starts with a word entry of how long it is
|
| /drivers/gpu/drm/bridge/ |
| D | Kconfig | 118 and starts encapsulation of HDMI signal.
|
| /drivers/mtd/ubi/ |
| D | Kconfig | 21 of UBI devices. When this threshold is exceeded, UBI starts performing
|
| /drivers/scsi/ |
| D | scsi_debug.c | 4150 int starts[SDEBUG_MAX_PARTS + 2]; in sdebug_build_parts() local
4165 starts[0] = sdebug_sectors_per; in sdebug_build_parts()
4167 starts[k] = ((k * sectors_per_part) / heads_by_sects) in sdebug_build_parts()
4169 starts[sdebug_num_parts] = num_sectors; in sdebug_build_parts()
4170 starts[sdebug_num_parts + 1] = 0; in sdebug_build_parts()
4175 for (k = 0; starts[k + 1]; ++k, ++pp) { in sdebug_build_parts()
4176 start_sec = starts[k]; in sdebug_build_parts()
4177 end_sec = starts[k + 1] - 1; in sdebug_build_parts()
|
| /drivers/staging/greybus/tools/ |
| D | README.loopback | 31 type - By writing the test type to this file, the test starts.
|
| /drivers/platform/chrome/ |
| D | Kconfig | 119 'pre-amble' bytes before the response actually starts.
|
| /drivers/block/paride/ |
| D | Transition-notes | 13 the result of ps_tq execution. Therefore, the sequence starts with
|
| /drivers/staging/wusbcore/Documentation/ |
| D | wusb-design-overview.rst | 298 starts sending MMCs.
323 into /devconnect/). This process starts the authentication process for
|
| /drivers/xen/ |
| D | Kconfig | 193 PCI topology starts at 00.00.0, or (1) for passthrough if you want
|
| /drivers/video/backlight/ |
| D | Kconfig | 52 power control driver for it. The panel starts up in power
|
| /drivers/auxdisplay/ |
| D | Kconfig | 189 modules with different arguments. Numbering starts with '0' for LPT1,
|
| /drivers/staging/rtl8192u/ |
| D | copying | 314 when it starts in an interactive mode:
|
| /drivers/scsi/aic7xxx/ |
| D | aic7xxx.reg | 66 * Each bit, when set starts a specific SCSI sequence on the bus
|
| D | aic79xx.seq | 904 * command phase starts. There is only one problem
|
| /drivers/video/fbdev/ |
| D | Kconfig | 1138 The driver starts in monitor mode. You must use the matroxset tool
1188 The driver starts in monitor mode and you must use the matroxset
|
| /drivers/rtc/ |
| D | Kconfig | 40 starts up, and when it resumes from a low power state. This
|
| /drivers/staging/speakup/ |
| D | spkguide.txt | 1098 speakup + f2. Speakup will tell you that the window starts at the
|