Home
last modified time | relevance | path

Searched refs:USB (Results 1 – 25 of 254) sorted by relevance

1234567891011

/arch/arm/boot/dts/
Dusb_a9g20.dts3 * usb_a9g20.dts - Device Tree file for Caloa USB A9G20 board
11 model = "Calao USB A9G20";
Dintel-ixp42x.dtsi15 * This is the USB Device Mode (UDC) controller, which is used
16 * to present the IXP4xx as a device on a USB bus.
Dusb_a9260.dts3 * usb_a9260.dts - Device Tree file for Caloa USB A9260 board
12 model = "Calao USB A9260";
Dusb_a9g20_lpw.dts3 * usb_a9g20_lpw.dts - Device Tree file for Caloa USB A9G20 Low Power board
11 model = "Calao USB A9G20 Low Power";
Dintel-ixp45x-ixp46x.dtsi17 * This is the USB Device Mode (UDC) controller, which is used
18 * to present the IXP4xx as a device on a USB bus.
Dkirkwood-ts219-6281.dts20 pmx_USB_copy_button: pmx-USB-copy-button {
44 label = "USB Copy";
Dkirkwood-ts219-6282.dts24 pmx_USB_copy_button: pmx-USB-copy-button {
44 label = "USB Copy";
Dorion5x-rd88f5182-nas.dts137 * MPP[22] USB 0 over current indication
138 * MPP[23] USB 1 over current indication
139 * MPP[24] USB 1 over current enable
140 * MPP[25] USB 0 over current enable
Dsun4i-a10-pcduino2.dts46 * is that the pcDuino2 board got a USB VBUS voltage regulator, which
48 * the USB host ports has been replaced with a USB WIFI chip.
64 usb1_vbus-supply = <&reg_vcc3v3>; /* USB WIFI is always on */
Dkirkwood-ts419.dtsi16 pmx_USB_copy_button: pmx-USB-copy-button {
45 label = "USB Copy";
Dkirkwood-laplug.dts90 regulator-name = "USB Power Back 1";
102 regulator-name = "USB Power Back 2";
114 regulator-name = "USB Power Front";
Darmada-370-seagate-personal-cloud.dtsi64 regulator-name = "USB Power";
102 label = "USB VBUS error";
128 /* USB 3.0 Bridge ASM1042A */
Domap3-beagle-xm-ab.dts9 /* HS USB Port 2 Power enable was inverted with the xM C */
Dusb_a9g20_common.dtsi3 * usb_a9g20.dts - Device Tree file for Caloa USB A9G20 board
Dsun8i-h2-plus-bananapi-m2-zero.dts171 * There're two micro-USB connectors, one is power-only and another is
173 * the external USB device will be powered just by the power input
174 * from the power-only USB port.
Dsun8i-h2-plus-orangepi-r1.dts54 * regulator on the original Zero. However it's used for USB
81 * RTL8152B USB-Ethernet adapter is connected to USB1,
82 * and it's a USB 2.0 device. So the OHCI1 controller
Dusb_a9263.dts3 * usb_a9263.dts - Device Tree file for Caloa USB A9293 board
11 model = "Calao USB A9263";
/arch/sh/kernel/cpu/sh3/
Dsetup-sh7705.c25 DMAC, SCIF0, SCIF2, ADC_ADI, USB, enumerator
43 INTC_VECT(USB, 0xa20), INTC_VECT(USB, 0xa40),
60 { 0xa4080000, 0, 16, 4, /* IPRF */ { 0, 0, USB } },
/arch/arm/mach-cns3xxx/
DKconfig18 for USB, USB-OTG, MMC/SD/SDIO, SATA, PCI-E, etc.
/arch/powerpc/platforms/embedded6xx/
DKconfig83 bool "USB Gecko udbg console for the Nintendo GameCube/Wii"
87 USB Gecko adapter as an udbg console.
88 The USB Gecko is a EXI to USB Serial converter that can be plugged
/arch/arm64/boot/dts/amlogic/
Dmeson-gxbb-odroidc2.dts153 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
154 * to be turned high in order to be detected by the USB Controller
155 * This signal should be handled by a USB specific power sequence
156 * in order to reset the Hub when USB bus is powered down.
192 "USB HUB nRESET", "USB OTG Power En",
/arch/sh/kernel/cpu/sh4/
Dsetup-sh7760.c26 USB, LCDC, enumerator
55 INTC_VECT(USB, 0xa00), INTC_VECT(LCDC, 0xa20),
89 SSI0, SSI1, HAC0, HAC1, I2C0, I2C1, USB, LCDC,
110 { 0xfe080008, 0, 32, 4, /* INTPRI08 */ { USB, LCDC, DMABRG, SCIF0,
/arch/sh/kernel/cpu/sh4a/
Dsetup-sh7366.c257 MFI, VPU, USB, enumerator
283 INTC_VECT(MFI, 0x900), INTC_VECT(VPU, 0x980), INTC_VECT(USB, 0xa20),
335 { 0, 0, 0, CMT, 0, USB, } },
350 { 0xa4080014, 0, 16, 4, /* IPRF */ { 0, DMAC45, USB, CMT } },
/arch/mips/boot/dts/brcm/
Dbcm97125cbmb.dts57 /* FIXME: USB is wonky; disable it for now */
/arch/sh/drivers/dma/
DKconfig47 The DMABRG does data transfers from main memory to Audio/USB units
49 Say Y if you want to use Audio/USB DMA on your SH7760 board.

1234567891011