1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3
4 bttv-cards.c
5
6 this file has configuration information - card-specific stuff
7 like the big tvcards array for the most part
8
9 Copyright (C) 1996,97,98 Ralph Metzler (rjkm@thp.uni-koeln.de)
10 & Marcus Metzler (mocm@thp.uni-koeln.de)
11 (c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de>
12
13
14 */
15
16 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
17
18 #include <linux/delay.h>
19 #include <linux/module.h>
20 #include <linux/kmod.h>
21 #include <linux/init.h>
22 #include <linux/pci.h>
23 #include <linux/vmalloc.h>
24 #include <linux/firmware.h>
25 #include <net/checksum.h>
26
27 #include <asm/unaligned.h>
28 #include <asm/io.h>
29
30 #include "bttvp.h"
31 #include <media/v4l2-common.h>
32 #include <media/i2c/tvaudio.h>
33 #include "bttv-audio-hook.h"
34
35 /* fwd decl */
36 static void boot_msp34xx(struct bttv *btv, int pin);
37 static void hauppauge_eeprom(struct bttv *btv);
38 static void avermedia_eeprom(struct bttv *btv);
39 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]);
40 static void modtec_eeprom(struct bttv *btv);
41 static void init_PXC200(struct bttv *btv);
42 static void init_RTV24(struct bttv *btv);
43 static void init_PCI8604PW(struct bttv *btv);
44
45 static void rv605_muxsel(struct bttv *btv, unsigned int input);
46 static void eagle_muxsel(struct bttv *btv, unsigned int input);
47 static void xguard_muxsel(struct bttv *btv, unsigned int input);
48 static void ivc120_muxsel(struct bttv *btv, unsigned int input);
49 static void gvc1100_muxsel(struct bttv *btv, unsigned int input);
50
51 static void PXC200_muxsel(struct bttv *btv, unsigned int input);
52
53 static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input);
54 static void picolo_tetra_init(struct bttv *btv);
55
56 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input);
57 static void tibetCS16_init(struct bttv *btv);
58
59 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input);
60 static void kodicom4400r_init(struct bttv *btv);
61
62 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input);
63 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input);
64
65 static void geovision_muxsel(struct bttv *btv, unsigned int input);
66
67 static void phytec_muxsel(struct bttv *btv, unsigned int input);
68
69 static void gv800s_muxsel(struct bttv *btv, unsigned int input);
70 static void gv800s_init(struct bttv *btv);
71
72 static void td3116_muxsel(struct bttv *btv, unsigned int input);
73
74 static int terratec_active_radio_upgrade(struct bttv *btv);
75 static int tea575x_init(struct bttv *btv);
76 static void identify_by_eeprom(struct bttv *btv,
77 unsigned char eeprom_data[256]);
78 static int pvr_boot(struct bttv *btv);
79
80 /* config variables */
81 static unsigned int triton1;
82 static unsigned int vsfx;
83 static unsigned int latency = UNSET;
84 int no_overlay=-1;
85
86 static unsigned int card[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
87 static unsigned int pll[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
88 static unsigned int tuner[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
89 static unsigned int svhs[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
90 static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
91 static unsigned int audiodev[BTTV_MAX];
92 static unsigned int saa6588[BTTV_MAX];
93 static struct bttv *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL };
94 static unsigned int autoload = UNSET;
95 static unsigned int gpiomask = UNSET;
96 static unsigned int audioall = UNSET;
97 static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET };
98
99 /* insmod options */
100 module_param(triton1, int, 0444);
101 module_param(vsfx, int, 0444);
102 module_param(no_overlay, int, 0444);
103 module_param(latency, int, 0444);
104 module_param(gpiomask, int, 0444);
105 module_param(audioall, int, 0444);
106 module_param(autoload, int, 0444);
107
108 module_param_array(card, int, NULL, 0444);
109 module_param_array(pll, int, NULL, 0444);
110 module_param_array(tuner, int, NULL, 0444);
111 module_param_array(svhs, int, NULL, 0444);
112 module_param_array(remote, int, NULL, 0444);
113 module_param_array(audiodev, int, NULL, 0444);
114 module_param_array(audiomux, int, NULL, 0444);
115
116 MODULE_PARM_DESC(triton1, "set ETBF pci config bit [enable bug compatibility for triton1 + others]");
117 MODULE_PARM_DESC(vsfx, "set VSFX pci config bit [yet another chipset flaw workaround]");
118 MODULE_PARM_DESC(latency,"pci latency timer");
119 MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list");
120 MODULE_PARM_DESC(pll, "specify installed crystal (0=none, 28=28 MHz, 35=35 MHz, 14=14 MHz)");
121 MODULE_PARM_DESC(tuner,"specify installed tuner type");
122 MODULE_PARM_DESC(autoload, "obsolete option, please do not use anymore");
123 MODULE_PARM_DESC(audiodev, "specify audio device:\n"
124 "\t\t-1 = no audio\n"
125 "\t\t 0 = autodetect (default)\n"
126 "\t\t 1 = msp3400\n"
127 "\t\t 2 = tda7432\n"
128 "\t\t 3 = tvaudio");
129 MODULE_PARM_DESC(saa6588, "if 1, then load the saa6588 RDS module, default (0) is to use the card definition.");
130 MODULE_PARM_DESC(no_overlay, "allow override overlay default (0 disables, 1 enables) [some VIA/SIS chipsets are known to have problem with overlay]");
131
132
133 /* I2C addresses list */
134 #define I2C_ADDR_TDA7432 0x8a
135 #define I2C_ADDR_MSP3400 0x80
136 #define I2C_ADDR_MSP3400_ALT 0x88
137
138
139 /* ----------------------------------------------------------------------- */
140 /* list of card IDs for bt878+ cards */
141
142 static struct CARD {
143 unsigned id;
144 int cardnr;
145 char *name;
146 } cards[] = {
147 { 0x13eb0070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV" },
148 { 0x39000070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV-D" },
149 { 0x45000070, BTTV_BOARD_HAUPPAUGEPVR, "Hauppauge WinTV/PVR" },
150 { 0xff000070, BTTV_BOARD_OSPREY1x0, "Osprey-100" },
151 { 0xff010070, BTTV_BOARD_OSPREY2x0_SVID,"Osprey-200" },
152 { 0xff020070, BTTV_BOARD_OSPREY500, "Osprey-500" },
153 { 0xff030070, BTTV_BOARD_OSPREY2000, "Osprey-2000" },
154 { 0xff040070, BTTV_BOARD_OSPREY540, "Osprey-540" },
155 { 0xff070070, BTTV_BOARD_OSPREY440, "Osprey-440" },
156
157 { 0x00011002, BTTV_BOARD_ATI_TVWONDER, "ATI TV Wonder" },
158 { 0x00031002, BTTV_BOARD_ATI_TVWONDERVE,"ATI TV Wonder/VE" },
159
160 { 0x6606107d, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
161 { 0x6607107d, BTTV_BOARD_WINFASTVC100, "Leadtek WinFast VC 100" },
162 { 0x6609107d, BTTV_BOARD_WINFAST2000, "Leadtek TV 2000 XP" },
163 { 0x263610b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
164 { 0x264510b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
165 { 0x402010fc, BTTV_BOARD_GVBCTV3PCI, "I-O Data Co. GV-BCTV3/PCI" },
166 { 0x405010fc, BTTV_BOARD_GVBCTV4PCI, "I-O Data Co. GV-BCTV4/PCI" },
167 { 0x407010fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
168 { 0xd01810fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
169
170 { 0x001211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
171 /* some cards ship with byteswapped IDs ... */
172 { 0x1200bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
173 { 0xff00bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
174 /* this seems to happen as well ... */
175 { 0xff1211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
176
177 { 0x3000121a, BTTV_BOARD_VOODOOTV_200, "3Dfx VoodooTV 200" },
178 { 0x263710b4, BTTV_BOARD_VOODOOTV_FM, "3Dfx VoodooTV FM" },
179 { 0x3060121a, BTTV_BOARD_STB2, "3Dfx VoodooTV 100/ STB OEM" },
180
181 { 0x3000144f, BTTV_BOARD_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" },
182 { 0xa005144f, BTTV_BOARD_MAGICTVIEW063, "CPH06X TView99-Card" },
183 { 0x3002144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" },
184 { 0x3005144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" },
185 { 0x5000144f, BTTV_BOARD_MAGICTVIEW061, "Askey CPH050" },
186 { 0x300014ff, BTTV_BOARD_MAGICTVIEW061, "TView 99 (CPH061)" },
187 { 0x300214ff, BTTV_BOARD_PHOEBE_TVMAS, "Phoebe TV Master (CPH060)" },
188
189 { 0x00011461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
190 { 0x00021461, BTTV_BOARD_AVERMEDIA98, "AVermedia TVCapture 98" },
191 { 0x00031461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
192 { 0x00041461, BTTV_BOARD_AVERMEDIA98, "AVerMedia TVCapture 98" },
193 { 0x03001461, BTTV_BOARD_AVERMEDIA98, "VDOMATE TV TUNER CARD" },
194
195 { 0x1117153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL B/G)" },
196 { 0x1118153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL B/G)" },
197 { 0x1119153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL I)" },
198 { 0x111a153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL I)" },
199
200 { 0x1123153b, BTTV_BOARD_TERRATVRADIO, "Terratec TV Radio+" },
201 { 0x1127153b, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.05)" },
202 /* clashes with FlyVideo
203 *{ 0x18521852, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.10)" }, */
204 { 0x1134153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (LR102)" },
205 { 0x1135153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* LR102 */
206 { 0x5018153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue" }, /* ?? */
207 { 0xff3b153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* ?? */
208
209 { 0x400015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
210 { 0x400a15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
211 { 0x400d15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
212 { 0x401015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
213 { 0x401615b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
214
215 { 0x1430aa00, BTTV_BOARD_PV143, "Provideo PV143A" },
216 { 0x1431aa00, BTTV_BOARD_PV143, "Provideo PV143B" },
217 { 0x1432aa00, BTTV_BOARD_PV143, "Provideo PV143C" },
218 { 0x1433aa00, BTTV_BOARD_PV143, "Provideo PV143D" },
219 { 0x1433aa03, BTTV_BOARD_PV143, "Security Eyes" },
220
221 { 0x1460aa00, BTTV_BOARD_PV150, "Provideo PV150A-1" },
222 { 0x1461aa01, BTTV_BOARD_PV150, "Provideo PV150A-2" },
223 { 0x1462aa02, BTTV_BOARD_PV150, "Provideo PV150A-3" },
224 { 0x1463aa03, BTTV_BOARD_PV150, "Provideo PV150A-4" },
225
226 { 0x1464aa04, BTTV_BOARD_PV150, "Provideo PV150B-1" },
227 { 0x1465aa05, BTTV_BOARD_PV150, "Provideo PV150B-2" },
228 { 0x1466aa06, BTTV_BOARD_PV150, "Provideo PV150B-3" },
229 { 0x1467aa07, BTTV_BOARD_PV150, "Provideo PV150B-4" },
230
231 { 0xa132ff00, BTTV_BOARD_IVC100, "IVC-100" },
232 { 0xa1550000, BTTV_BOARD_IVC200, "IVC-200" },
233 { 0xa1550001, BTTV_BOARD_IVC200, "IVC-200" },
234 { 0xa1550002, BTTV_BOARD_IVC200, "IVC-200" },
235 { 0xa1550003, BTTV_BOARD_IVC200, "IVC-200" },
236 { 0xa1550100, BTTV_BOARD_IVC200, "IVC-200G" },
237 { 0xa1550101, BTTV_BOARD_IVC200, "IVC-200G" },
238 { 0xa1550102, BTTV_BOARD_IVC200, "IVC-200G" },
239 { 0xa1550103, BTTV_BOARD_IVC200, "IVC-200G" },
240 { 0xa1550800, BTTV_BOARD_IVC200, "IVC-200" },
241 { 0xa1550801, BTTV_BOARD_IVC200, "IVC-200" },
242 { 0xa1550802, BTTV_BOARD_IVC200, "IVC-200" },
243 { 0xa1550803, BTTV_BOARD_IVC200, "IVC-200" },
244 { 0xa182ff00, BTTV_BOARD_IVC120, "IVC-120G" },
245 { 0xa182ff01, BTTV_BOARD_IVC120, "IVC-120G" },
246 { 0xa182ff02, BTTV_BOARD_IVC120, "IVC-120G" },
247 { 0xa182ff03, BTTV_BOARD_IVC120, "IVC-120G" },
248 { 0xa182ff04, BTTV_BOARD_IVC120, "IVC-120G" },
249 { 0xa182ff05, BTTV_BOARD_IVC120, "IVC-120G" },
250 { 0xa182ff06, BTTV_BOARD_IVC120, "IVC-120G" },
251 { 0xa182ff07, BTTV_BOARD_IVC120, "IVC-120G" },
252 { 0xa182ff08, BTTV_BOARD_IVC120, "IVC-120G" },
253 { 0xa182ff09, BTTV_BOARD_IVC120, "IVC-120G" },
254 { 0xa182ff0a, BTTV_BOARD_IVC120, "IVC-120G" },
255 { 0xa182ff0b, BTTV_BOARD_IVC120, "IVC-120G" },
256 { 0xa182ff0c, BTTV_BOARD_IVC120, "IVC-120G" },
257 { 0xa182ff0d, BTTV_BOARD_IVC120, "IVC-120G" },
258 { 0xa182ff0e, BTTV_BOARD_IVC120, "IVC-120G" },
259 { 0xa182ff0f, BTTV_BOARD_IVC120, "IVC-120G" },
260 { 0xf0500000, BTTV_BOARD_IVCE8784, "IVCE-8784" },
261 { 0xf0500001, BTTV_BOARD_IVCE8784, "IVCE-8784" },
262 { 0xf0500002, BTTV_BOARD_IVCE8784, "IVCE-8784" },
263 { 0xf0500003, BTTV_BOARD_IVCE8784, "IVCE-8784" },
264
265 { 0x41424344, BTTV_BOARD_GRANDTEC, "GrandTec Multi Capture" },
266 { 0x01020304, BTTV_BOARD_XGUARD, "Grandtec Grand X-Guard" },
267
268 { 0x18501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
269 { 0xa0501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
270 { 0x18511851, BTTV_BOARD_FLYVIDEO98EZ, "FlyVideo 98EZ (LR51)/ CyberMail AV" },
271 { 0x18521852, BTTV_BOARD_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" },
272 { 0x41a0a051, BTTV_BOARD_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" },
273 { 0x18501f7f, BTTV_BOARD_FLYVIDEO_98, "Lifeview Flyvideo 98" },
274
275 { 0x010115cb, BTTV_BOARD_GMV1, "AG GMV1" },
276 { 0x010114c7, BTTV_BOARD_MODTEC_205, "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" },
277
278 { 0x10b42636, BTTV_BOARD_HAUPPAUGE878, "STB ???" },
279 { 0x217d6606, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
280 { 0xfff6f6ff, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
281 { 0x03116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 311" },
282 { 0x06116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 611" },
283 { 0x00790e11, BTTV_BOARD_WINDVR, "Canopus WinDVR PCI" },
284 { 0xa0fca1a0, BTTV_BOARD_ZOLTRIX, "Face to Face Tvmax" },
285 { 0x82b2aa6a, BTTV_BOARD_SIMUS_GVC1100, "SIMUS GVC1100" },
286 { 0x146caa0c, BTTV_BOARD_PV951, "ituner spectra8" },
287 { 0x200a1295, BTTV_BOARD_PXC200, "ImageNation PXC200A" },
288
289 { 0x40111554, BTTV_BOARD_PV_BT878P_9B, "Prolink Pixelview PV-BT" },
290 { 0x17de0a01, BTTV_BOARD_KWORLD, "Mecer TV/FM/Video Tuner" },
291
292 { 0x01051805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" },
293 { 0x01061805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" },
294 { 0x01071805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" },
295 { 0x01081805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" },
296
297 { 0x15409511, BTTV_BOARD_ACORP_Y878F, "Acorp Y878F" },
298
299 { 0x53534149, BTTV_BOARD_SSAI_SECURITY, "SSAI Security Video Interface" },
300 { 0x5353414a, BTTV_BOARD_SSAI_ULTRASOUND, "SSAI Ultrasound Video Interface" },
301
302 /* likely broken, vendor id doesn't match the other magic views ...
303 * { 0xa0fca04f, BTTV_BOARD_MAGICTVIEW063, "Guillemot Maxi TV Video 3" }, */
304
305 /* Duplicate PCI ID, reconfigure for this board during the eeprom read.
306 * { 0x13eb0070, BTTV_BOARD_HAUPPAUGE_IMPACTVCB, "Hauppauge ImpactVCB" }, */
307
308 { 0x109e036e, BTTV_BOARD_CONCEPTRONIC_CTVFMI2, "Conceptronic CTVFMi v2"},
309
310 /* DVB cards (using pci function .1 for mpeg data xfer) */
311 { 0x001c11bd, BTTV_BOARD_PINNACLESAT, "Pinnacle PCTV Sat" },
312 { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" },
313 { 0x20007063, BTTV_BOARD_PC_HDTV, "pcHDTV HD-2000 TV"},
314 { 0x002611bd, BTTV_BOARD_TWINHAN_DST, "Pinnacle PCTV SAT CI" },
315 { 0x00011822, BTTV_BOARD_TWINHAN_DST, "Twinhan VisionPlus DVB" },
316 { 0xfc00270f, BTTV_BOARD_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" },
317 { 0x07711461, BTTV_BOARD_AVDVBT_771, "AVermedia AverTV DVB-T 771" },
318 { 0x07611461, BTTV_BOARD_AVDVBT_761, "AverMedia AverTV DVB-T 761" },
319 { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE, "DViCO FusionHDTV DVB-T Lite" },
320 { 0xdb1118ac, BTTV_BOARD_DVICO_DVBT_LITE, "Ultraview DVB-T Lite" },
321 { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE, "DViCO FusionHDTV 5 Lite" },
322 { 0x00261822, BTTV_BOARD_TWINHAN_DST, "DNTV Live! Mini "},
323 { 0xd200dbc0, BTTV_BOARD_DVICO_FUSIONHDTV_2, "DViCO FusionHDTV 2" },
324 { 0x763c008a, BTTV_BOARD_GEOVISION_GV600, "GeoVision GV-600" },
325 { 0x18011000, BTTV_BOARD_ENLTV_FM_2, "Encore ENL TV-FM-2" },
326 { 0x763d800a, BTTV_BOARD_GEOVISION_GV800S, "GeoVision GV-800(S) (master)" },
327 { 0x763d800b, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" },
328 { 0x763d800c, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" },
329 { 0x763d800d, BTTV_BOARD_GEOVISION_GV800S_SL, "GeoVision GV-800(S) (slave)" },
330
331 { 0x15401830, BTTV_BOARD_PV183, "Provideo PV183-1" },
332 { 0x15401831, BTTV_BOARD_PV183, "Provideo PV183-2" },
333 { 0x15401832, BTTV_BOARD_PV183, "Provideo PV183-3" },
334 { 0x15401833, BTTV_BOARD_PV183, "Provideo PV183-4" },
335 { 0x15401834, BTTV_BOARD_PV183, "Provideo PV183-5" },
336 { 0x15401835, BTTV_BOARD_PV183, "Provideo PV183-6" },
337 { 0x15401836, BTTV_BOARD_PV183, "Provideo PV183-7" },
338 { 0x15401837, BTTV_BOARD_PV183, "Provideo PV183-8" },
339 { 0x3116f200, BTTV_BOARD_TVT_TD3116, "Tongwei Video Technology TD-3116" },
340 { 0x02280279, BTTV_BOARD_APOSONIC_WDVR, "Aposonic W-DVR" },
341 { 0, -1, NULL }
342 };
343
344 /* ----------------------------------------------------------------------- */
345 /* array with description for bt848 / bt878 tv/grabber cards */
346
347 struct tvcard bttv_tvcards[] = {
348 /* ---- card 0x00 ---------------------------------- */
349 [BTTV_BOARD_UNKNOWN] = {
350 .name = " *** UNKNOWN/GENERIC *** ",
351 .video_inputs = 4,
352 .svhs = 2,
353 .muxsel = MUXSEL(2, 3, 1, 0),
354 .tuner_type = UNSET,
355 .tuner_addr = ADDR_UNSET,
356 },
357 [BTTV_BOARD_MIRO] = {
358 .name = "MIRO PCTV",
359 .video_inputs = 4,
360 /* .audio_inputs= 1, */
361 .svhs = 2,
362 .gpiomask = 15,
363 .muxsel = MUXSEL(2, 3, 1, 1),
364 .gpiomux = { 2, 0, 0, 0 },
365 .gpiomute = 10,
366 .tuner_type = UNSET,
367 .tuner_addr = ADDR_UNSET,
368 },
369 [BTTV_BOARD_HAUPPAUGE] = {
370 .name = "Hauppauge (bt848)",
371 .video_inputs = 4,
372 /* .audio_inputs= 1, */
373 .svhs = 2,
374 .gpiomask = 7,
375 .muxsel = MUXSEL(2, 3, 1, 1),
376 .gpiomux = { 0, 1, 2, 3 },
377 .gpiomute = 4,
378 .tuner_type = UNSET,
379 .tuner_addr = ADDR_UNSET,
380 },
381 [BTTV_BOARD_STB] = {
382 .name = "STB, Gateway P/N 6000699 (bt848)",
383 .video_inputs = 3,
384 /* .audio_inputs= 1, */
385 .svhs = 2,
386 .gpiomask = 7,
387 .muxsel = MUXSEL(2, 3, 1, 1),
388 .gpiomux = { 4, 0, 2, 3 },
389 .gpiomute = 1,
390 .no_msp34xx = 1,
391 .tuner_type = TUNER_PHILIPS_NTSC,
392 .tuner_addr = ADDR_UNSET,
393 .pll = PLL_28,
394 .has_radio = 1,
395 },
396
397 /* ---- card 0x04 ---------------------------------- */
398 [BTTV_BOARD_INTEL] = {
399 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
400 .video_inputs = 4,
401 /* .audio_inputs= 0, */
402 .svhs = 2,
403 .gpiomask = 0,
404 .muxsel = MUXSEL(2, 3, 1, 1),
405 .gpiomux = { 0 },
406 .tuner_type = TUNER_ABSENT,
407 .tuner_addr = ADDR_UNSET,
408 },
409 [BTTV_BOARD_DIAMOND] = {
410 .name = "Diamond DTV2000",
411 .video_inputs = 4,
412 /* .audio_inputs= 1, */
413 .svhs = 2,
414 .gpiomask = 3,
415 .muxsel = MUXSEL(2, 3, 1, 0),
416 .gpiomux = { 0, 1, 0, 1 },
417 .gpiomute = 3,
418 .tuner_type = UNSET,
419 .tuner_addr = ADDR_UNSET,
420 },
421 [BTTV_BOARD_AVERMEDIA] = {
422 .name = "AVerMedia TVPhone",
423 .video_inputs = 3,
424 /* .audio_inputs= 1, */
425 .svhs = 3,
426 .muxsel = MUXSEL(2, 3, 1, 1),
427 .gpiomask = 0x0f,
428 .gpiomux = { 0x0c, 0x04, 0x08, 0x04 },
429 /* 0x04 for some cards ?? */
430 .tuner_type = UNSET,
431 .tuner_addr = ADDR_UNSET,
432 .audio_mode_gpio= avermedia_tvphone_audio,
433 .has_remote = 1,
434 },
435 [BTTV_BOARD_MATRIX_VISION] = {
436 .name = "MATRIX-Vision MV-Delta",
437 .video_inputs = 5,
438 /* .audio_inputs= 1, */
439 .svhs = 3,
440 .gpiomask = 0,
441 .muxsel = MUXSEL(2, 3, 1, 0, 0),
442 .gpiomux = { 0 },
443 .tuner_type = TUNER_ABSENT,
444 .tuner_addr = ADDR_UNSET,
445 },
446
447 /* ---- card 0x08 ---------------------------------- */
448 [BTTV_BOARD_FLYVIDEO] = {
449 .name = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26",
450 .video_inputs = 4,
451 /* .audio_inputs= 1, */
452 .svhs = 2,
453 .gpiomask = 0xc00,
454 .muxsel = MUXSEL(2, 3, 1, 1),
455 .gpiomux = { 0, 0xc00, 0x800, 0x400 },
456 .gpiomute = 0xc00,
457 .pll = PLL_28,
458 .tuner_type = UNSET,
459 .tuner_addr = ADDR_UNSET,
460 },
461 [BTTV_BOARD_TURBOTV] = {
462 .name = "IMS/IXmicro TurboTV",
463 .video_inputs = 3,
464 /* .audio_inputs= 1, */
465 .svhs = 2,
466 .gpiomask = 3,
467 .muxsel = MUXSEL(2, 3, 1, 1),
468 .gpiomux = { 1, 1, 2, 3 },
469 .pll = PLL_28,
470 .tuner_type = TUNER_TEMIC_PAL,
471 .tuner_addr = ADDR_UNSET,
472 },
473 [BTTV_BOARD_HAUPPAUGE878] = {
474 .name = "Hauppauge (bt878)",
475 .video_inputs = 4,
476 /* .audio_inputs= 1, */
477 .svhs = 2,
478 .gpiomask = 0x0f, /* old: 7 */
479 .muxsel = MUXSEL(2, 0, 1, 1),
480 .gpiomux = { 0, 1, 2, 3 },
481 .gpiomute = 4,
482 .pll = PLL_28,
483 .tuner_type = UNSET,
484 .tuner_addr = ADDR_UNSET,
485 },
486 [BTTV_BOARD_MIROPRO] = {
487 .name = "MIRO PCTV pro",
488 .video_inputs = 3,
489 /* .audio_inputs= 1, */
490 .svhs = 2,
491 .gpiomask = 0x3014f,
492 .muxsel = MUXSEL(2, 3, 1, 1),
493 .gpiomux = { 0x20001,0x10001, 0, 0 },
494 .gpiomute = 10,
495 .tuner_type = UNSET,
496 .tuner_addr = ADDR_UNSET,
497 },
498
499 /* ---- card 0x0c ---------------------------------- */
500 [BTTV_BOARD_ADSTECH_TV] = {
501 .name = "ADS Technologies Channel Surfer TV (bt848)",
502 .video_inputs = 3,
503 /* .audio_inputs= 1, */
504 .svhs = 2,
505 .gpiomask = 15,
506 .muxsel = MUXSEL(2, 3, 1, 1),
507 .gpiomux = { 13, 14, 11, 7 },
508 .tuner_type = UNSET,
509 .tuner_addr = ADDR_UNSET,
510 },
511 [BTTV_BOARD_AVERMEDIA98] = {
512 .name = "AVerMedia TVCapture 98",
513 .video_inputs = 3,
514 /* .audio_inputs= 4, */
515 .svhs = 2,
516 .gpiomask = 15,
517 .muxsel = MUXSEL(2, 3, 1, 1),
518 .gpiomux = { 13, 14, 11, 7 },
519 .msp34xx_alt = 1,
520 .pll = PLL_28,
521 .tuner_type = TUNER_PHILIPS_PAL,
522 .tuner_addr = ADDR_UNSET,
523 .audio_mode_gpio= avermedia_tv_stereo_audio,
524 .no_gpioirq = 1,
525 },
526 [BTTV_BOARD_VHX] = {
527 .name = "Aimslab Video Highway Xtreme (VHX)",
528 .video_inputs = 3,
529 /* .audio_inputs= 1, */
530 .svhs = 2,
531 .gpiomask = 7,
532 .muxsel = MUXSEL(2, 3, 1, 1),
533 .gpiomux = { 0, 2, 1, 3 }, /* old: {0, 1, 2, 3, 4} */
534 .gpiomute = 4,
535 .pll = PLL_28,
536 .tuner_type = UNSET,
537 .tuner_addr = ADDR_UNSET,
538 },
539 [BTTV_BOARD_ZOLTRIX] = {
540 .name = "Zoltrix TV-Max",
541 .video_inputs = 3,
542 /* .audio_inputs= 1, */
543 .svhs = 2,
544 .gpiomask = 15,
545 .muxsel = MUXSEL(2, 3, 1, 1),
546 .gpiomux = { 0, 0, 1, 0 },
547 .gpiomute = 10,
548 .tuner_type = UNSET,
549 .tuner_addr = ADDR_UNSET,
550 },
551
552 /* ---- card 0x10 ---------------------------------- */
553 [BTTV_BOARD_PIXVIEWPLAYTV] = {
554 .name = "Prolink Pixelview PlayTV (bt878)",
555 .video_inputs = 3,
556 /* .audio_inputs= 1, */
557 .svhs = 2,
558 .gpiomask = 0x01fe00,
559 .muxsel = MUXSEL(2, 3, 1, 1),
560 /* 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru> */
561 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
562 .gpiomute = 0x002000,
563 .pll = PLL_28,
564 .tuner_type = UNSET,
565 .tuner_addr = ADDR_UNSET,
566 },
567 [BTTV_BOARD_WINVIEW_601] = {
568 .name = "Leadtek WinView 601",
569 .video_inputs = 3,
570 /* .audio_inputs= 1, */
571 .svhs = 2,
572 .gpiomask = 0x8300f8,
573 .muxsel = MUXSEL(2, 3, 1, 1, 0),
574 .gpiomux = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007 },
575 .gpiomute = 0xcfa007,
576 .tuner_type = UNSET,
577 .tuner_addr = ADDR_UNSET,
578 .volume_gpio = winview_volume,
579 .has_radio = 1,
580 },
581 [BTTV_BOARD_AVEC_INTERCAP] = {
582 .name = "AVEC Intercapture",
583 .video_inputs = 3,
584 /* .audio_inputs= 2, */
585 .svhs = 2,
586 .gpiomask = 0,
587 .muxsel = MUXSEL(2, 3, 1, 1),
588 .gpiomux = { 1, 0, 0, 0 },
589 .tuner_type = UNSET,
590 .tuner_addr = ADDR_UNSET,
591 },
592 [BTTV_BOARD_LIFE_FLYKIT] = {
593 .name = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)",
594 .video_inputs = 4,
595 /* .audio_inputs= 1, */
596 .svhs = NO_SVHS,
597 .gpiomask = 0x8dff00,
598 .muxsel = MUXSEL(2, 3, 1, 1),
599 .gpiomux = { 0 },
600 .no_msp34xx = 1,
601 .tuner_type = TUNER_ABSENT,
602 .tuner_addr = ADDR_UNSET,
603 },
604
605 /* ---- card 0x14 ---------------------------------- */
606 [BTTV_BOARD_CEI_RAFFLES] = {
607 .name = "CEI Raffles Card",
608 .video_inputs = 3,
609 /* .audio_inputs= 3, */
610 .svhs = 2,
611 .muxsel = MUXSEL(2, 3, 1, 1),
612 .tuner_type = UNSET,
613 .tuner_addr = ADDR_UNSET,
614 },
615 [BTTV_BOARD_CONFERENCETV] = {
616 .name = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50",
617 .video_inputs = 4,
618 /* .audio_inputs= 2, tuner, line in */
619 .svhs = 2,
620 .gpiomask = 0x1800,
621 .muxsel = MUXSEL(2, 3, 1, 1),
622 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
623 .gpiomute = 0x1800,
624 .pll = PLL_28,
625 .tuner_type = TUNER_PHILIPS_PAL_I,
626 .tuner_addr = ADDR_UNSET,
627 },
628 [BTTV_BOARD_PHOEBE_TVMAS] = {
629 .name = "Askey CPH050/ Phoebe Tv Master + FM",
630 .video_inputs = 3,
631 /* .audio_inputs= 1, */
632 .svhs = 2,
633 .gpiomask = 0xc00,
634 .muxsel = MUXSEL(2, 3, 1, 1),
635 .gpiomux = { 0, 1, 0x800, 0x400 },
636 .gpiomute = 0xc00,
637 .pll = PLL_28,
638 .tuner_type = UNSET,
639 .tuner_addr = ADDR_UNSET,
640 },
641 [BTTV_BOARD_MODTEC_205] = {
642 .name = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878",
643 .video_inputs = 3,
644 /* .audio_inputs= 1, */
645 .svhs = NO_SVHS,
646 .has_dig_in = 1,
647 .gpiomask = 7,
648 .muxsel = MUXSEL(2, 3, 0), /* input 2 is digital */
649 /* .digital_mode= DIGITAL_MODE_CAMERA, */
650 .gpiomux = { 0, 0, 0, 0 },
651 .no_msp34xx = 1,
652 .pll = PLL_28,
653 .tuner_type = TUNER_ALPS_TSBB5_PAL_I,
654 .tuner_addr = ADDR_UNSET,
655 },
656
657 /* ---- card 0x18 ---------------------------------- */
658 [BTTV_BOARD_MAGICTVIEW061] = {
659 .name = "Askey CPH05X/06X (bt878) [many vendors]",
660 .video_inputs = 3,
661 /* .audio_inputs= 1, */
662 .svhs = 2,
663 .gpiomask = 0xe00,
664 .muxsel = MUXSEL(2, 3, 1, 1),
665 .gpiomux = {0x400, 0x400, 0x400, 0x400 },
666 .gpiomute = 0xc00,
667 .pll = PLL_28,
668 .tuner_type = UNSET,
669 .tuner_addr = ADDR_UNSET,
670 .has_remote = 1,
671 .has_radio = 1, /* not every card has radio */
672 },
673 [BTTV_BOARD_VOBIS_BOOSTAR] = {
674 .name = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar",
675 .video_inputs = 3,
676 /* .audio_inputs= 1, */
677 .svhs = 2,
678 .gpiomask = 0x1f0fff,
679 .muxsel = MUXSEL(2, 3, 1, 1),
680 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
681 .gpiomute = 0x40000,
682 .tuner_type = TUNER_PHILIPS_PAL,
683 .tuner_addr = ADDR_UNSET,
684 .audio_mode_gpio= terratv_audio,
685 },
686 [BTTV_BOARD_HAUPPAUG_WCAM] = {
687 .name = "Hauppauge WinCam newer (bt878)",
688 .video_inputs = 4,
689 /* .audio_inputs= 1, */
690 .svhs = 3,
691 .gpiomask = 7,
692 .muxsel = MUXSEL(2, 0, 1, 1),
693 .gpiomux = { 0, 1, 2, 3 },
694 .gpiomute = 4,
695 .tuner_type = UNSET,
696 .tuner_addr = ADDR_UNSET,
697 },
698 [BTTV_BOARD_MAXI] = {
699 .name = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50",
700 .video_inputs = 4,
701 /* .audio_inputs= 2, */
702 .svhs = 2,
703 .gpiomask = 0x1800,
704 .muxsel = MUXSEL(2, 3, 1, 1),
705 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
706 .gpiomute = 0x1800,
707 .pll = PLL_28,
708 .tuner_type = TUNER_PHILIPS_SECAM,
709 .tuner_addr = ADDR_UNSET,
710 },
711
712 /* ---- card 0x1c ---------------------------------- */
713 [BTTV_BOARD_TERRATV] = {
714 .name = "Terratec TerraTV+ Version 1.1 (bt878)",
715 .video_inputs = 3,
716 /* .audio_inputs= 1, */
717 .svhs = 2,
718 .gpiomask = 0x1f0fff,
719 .muxsel = MUXSEL(2, 3, 1, 1),
720 .gpiomux = { 0x20000, 0x30000, 0x10000, 0x00000 },
721 .gpiomute = 0x40000,
722 .tuner_type = TUNER_PHILIPS_PAL,
723 .tuner_addr = ADDR_UNSET,
724 .audio_mode_gpio= terratv_audio,
725 /* GPIO wiring:
726 External 20 pin connector (for Active Radio Upgrade board)
727 gpio00: i2c-sda
728 gpio01: i2c-scl
729 gpio02: om5610-data
730 gpio03: om5610-clk
731 gpio04: om5610-wre
732 gpio05: om5610-stereo
733 gpio06: rds6588-davn
734 gpio07: Pin 7 n.c.
735 gpio08: nIOW
736 gpio09+10: nIOR, nSEL ?? (bt878)
737 gpio09: nIOR (bt848)
738 gpio10: nSEL (bt848)
739 Sound Routing:
740 gpio16: u2-A0 (1st 4052bt)
741 gpio17: u2-A1
742 gpio18: u2-nEN
743 gpio19: u4-A0 (2nd 4052)
744 gpio20: u4-A1
745 u4-nEN - GND
746 Btspy:
747 00000 : Cdrom (internal audio input)
748 10000 : ext. Video audio input
749 20000 : TV Mono
750 a0000 : TV Mono/2
751 1a0000 : TV Stereo
752 30000 : Radio
753 40000 : Mute
754 */
755
756 },
757 [BTTV_BOARD_PXC200] = {
758 /* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */
759 .name = "Imagenation PXC200",
760 .video_inputs = 5,
761 /* .audio_inputs= 1, */
762 .svhs = 1, /* was: 4 */
763 .gpiomask = 0,
764 .muxsel = MUXSEL(2, 3, 1, 0, 0),
765 .gpiomux = { 0 },
766 .tuner_type = TUNER_ABSENT,
767 .tuner_addr = ADDR_UNSET,
768 .muxsel_hook = PXC200_muxsel,
769
770 },
771 [BTTV_BOARD_FLYVIDEO_98] = {
772 .name = "Lifeview FlyVideo 98 LR50",
773 .video_inputs = 4,
774 /* .audio_inputs= 1, */
775 .svhs = 2,
776 .gpiomask = 0x1800, /* 0x8dfe00 */
777 .muxsel = MUXSEL(2, 3, 1, 1),
778 .gpiomux = { 0, 0x0800, 0x1000, 0x1000 },
779 .gpiomute = 0x1800,
780 .pll = PLL_28,
781 .tuner_type = UNSET,
782 .tuner_addr = ADDR_UNSET,
783 },
784 [BTTV_BOARD_IPROTV] = {
785 .name = "Formac iProTV, Formac ProTV I (bt848)",
786 .video_inputs = 4,
787 /* .audio_inputs= 1, */
788 .svhs = 3,
789 .gpiomask = 1,
790 .muxsel = MUXSEL(2, 3, 1, 1),
791 .gpiomux = { 1, 0, 0, 0 },
792 .pll = PLL_28,
793 .tuner_type = TUNER_PHILIPS_PAL,
794 .tuner_addr = ADDR_UNSET,
795 },
796
797 /* ---- card 0x20 ---------------------------------- */
798 [BTTV_BOARD_INTEL_C_S_PCI] = {
799 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
800 .video_inputs = 4,
801 /* .audio_inputs= 0, */
802 .svhs = 2,
803 .gpiomask = 0,
804 .muxsel = MUXSEL(2, 3, 1, 1),
805 .gpiomux = { 0 },
806 .tuner_type = TUNER_ABSENT,
807 .tuner_addr = ADDR_UNSET,
808 },
809 [BTTV_BOARD_TERRATVALUE] = {
810 .name = "Terratec TerraTValue Version Bt878",
811 .video_inputs = 3,
812 /* .audio_inputs= 1, */
813 .svhs = 2,
814 .gpiomask = 0xffff00,
815 .muxsel = MUXSEL(2, 3, 1, 1),
816 .gpiomux = { 0x500, 0, 0x300, 0x900 },
817 .gpiomute = 0x900,
818 .pll = PLL_28,
819 .tuner_type = TUNER_PHILIPS_PAL,
820 .tuner_addr = ADDR_UNSET,
821 },
822 [BTTV_BOARD_WINFAST2000] = {
823 .name = "Leadtek WinFast 2000/ WinFast 2000 XP",
824 .video_inputs = 4,
825 /* .audio_inputs= 1, */
826 .svhs = 2,
827 /* TV, CVid, SVid, CVid over SVid connector */
828 .muxsel = MUXSEL(2, 3, 1, 1, 0),
829 /* Alexander Varakin <avarakin@hotmail.com> [stereo version] */
830 .gpiomask = 0xb33000,
831 .gpiomux = { 0x122000,0x1000,0x0000,0x620000 },
832 .gpiomute = 0x800000,
833 /* Audio Routing for "WinFast 2000 XP" (no tv stereo !)
834 gpio23 -- hef4052:nEnable (0x800000)
835 gpio12 -- hef4052:A1
836 gpio13 -- hef4052:A0
837 0x0000: external audio
838 0x1000: FM
839 0x2000: TV
840 0x3000: n.c.
841 Note: There exists another variant "Winfast 2000" with tv stereo !?
842 Note: eeprom only contains FF and pci subsystem id 107d:6606
843 */
844 .pll = PLL_28,
845 .has_radio = 1,
846 .tuner_type = TUNER_PHILIPS_PAL, /* default for now, gpio reads BFFF06 for Pal bg+dk */
847 .tuner_addr = ADDR_UNSET,
848 .audio_mode_gpio= winfast2000_audio,
849 .has_remote = 1,
850 },
851 [BTTV_BOARD_CHRONOS_VS2] = {
852 .name = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II",
853 .video_inputs = 4,
854 /* .audio_inputs= 3, */
855 .svhs = 2,
856 .gpiomask = 0x1800,
857 .muxsel = MUXSEL(2, 3, 1, 1),
858 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
859 .gpiomute = 0x1800,
860 .pll = PLL_28,
861 .tuner_type = UNSET,
862 .tuner_addr = ADDR_UNSET,
863 },
864
865 /* ---- card 0x24 ---------------------------------- */
866 [BTTV_BOARD_TYPHOON_TVIEW] = {
867 .name = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner",
868 .video_inputs = 4,
869 /* .audio_inputs= 3, */
870 .svhs = 2,
871 .gpiomask = 0x1800,
872 .muxsel = MUXSEL(2, 3, 1, 1),
873 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
874 .gpiomute = 0x1800,
875 .pll = PLL_28,
876 .tuner_type = UNSET,
877 .tuner_addr = ADDR_UNSET,
878 .has_radio = 1,
879 },
880 [BTTV_BOARD_PXELVWPLTVPRO] = {
881 .name = "Prolink PixelView PlayTV pro",
882 .video_inputs = 3,
883 /* .audio_inputs= 1, */
884 .svhs = 2,
885 .gpiomask = 0xff,
886 .muxsel = MUXSEL(2, 3, 1, 1),
887 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
888 .gpiomute = 0x29,
889 .no_msp34xx = 1,
890 .pll = PLL_28,
891 .tuner_type = UNSET,
892 .tuner_addr = ADDR_UNSET,
893 },
894 [BTTV_BOARD_MAGICTVIEW063] = {
895 .name = "Askey CPH06X TView99",
896 .video_inputs = 4,
897 /* .audio_inputs= 1, */
898 .svhs = 2,
899 .gpiomask = 0x551e00,
900 .muxsel = MUXSEL(2, 3, 1, 0),
901 .gpiomux = { 0x551400, 0x551200, 0, 0 },
902 .gpiomute = 0x551c00,
903 .pll = PLL_28,
904 .tuner_type = TUNER_PHILIPS_PAL_I,
905 .tuner_addr = ADDR_UNSET,
906 .has_remote = 1,
907 },
908 [BTTV_BOARD_PINNACLE] = {
909 .name = "Pinnacle PCTV Studio/Rave",
910 .video_inputs = 3,
911 /* .audio_inputs= 1, */
912 .svhs = 2,
913 .gpiomask = 0x03000F,
914 .muxsel = MUXSEL(2, 3, 1, 1),
915 .gpiomux = { 2, 0xd0001, 0, 0 },
916 .gpiomute = 1,
917 .pll = PLL_28,
918 .tuner_type = UNSET,
919 .tuner_addr = ADDR_UNSET,
920 },
921
922 /* ---- card 0x28 ---------------------------------- */
923 [BTTV_BOARD_STB2] = {
924 .name = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100",
925 .video_inputs = 3,
926 /* .audio_inputs= 1, */
927 .svhs = 2,
928 .gpiomask = 7,
929 .muxsel = MUXSEL(2, 3, 1, 1),
930 .gpiomux = { 4, 0, 2, 3 },
931 .gpiomute = 1,
932 .no_msp34xx = 1,
933 .tuner_type = TUNER_PHILIPS_NTSC,
934 .tuner_addr = ADDR_UNSET,
935 .pll = PLL_28,
936 .has_radio = 1,
937 },
938 [BTTV_BOARD_AVPHONE98] = {
939 .name = "AVerMedia TVPhone 98",
940 .video_inputs = 3,
941 /* .audio_inputs= 4, */
942 .svhs = 2,
943 .gpiomask = 15,
944 .muxsel = MUXSEL(2, 3, 1, 1),
945 .gpiomux = { 13, 4, 11, 7 },
946 .pll = PLL_28,
947 .tuner_type = UNSET,
948 .tuner_addr = ADDR_UNSET,
949 .has_radio = 1,
950 .audio_mode_gpio= avermedia_tvphone_audio,
951 },
952 [BTTV_BOARD_PV951] = {
953 .name = "ProVideo PV951", /* pic16c54 */
954 .video_inputs = 3,
955 /* .audio_inputs= 1, */
956 .svhs = 2,
957 .gpiomask = 0,
958 .muxsel = MUXSEL(2, 3, 1, 1),
959 .gpiomux = { 0, 0, 0, 0},
960 .no_msp34xx = 1,
961 .pll = PLL_28,
962 .tuner_type = TUNER_PHILIPS_PAL_I,
963 .tuner_addr = ADDR_UNSET,
964 },
965 [BTTV_BOARD_ONAIR_TV] = {
966 .name = "Little OnAir TV",
967 .video_inputs = 3,
968 /* .audio_inputs= 1, */
969 .svhs = 2,
970 .gpiomask = 0xe00b,
971 .muxsel = MUXSEL(2, 3, 1, 1),
972 .gpiomux = { 0xff9ff6, 0xff9ff6, 0xff1ff7, 0 },
973 .gpiomute = 0xff3ffc,
974 .no_msp34xx = 1,
975 .tuner_type = UNSET,
976 .tuner_addr = ADDR_UNSET,
977 },
978
979 /* ---- card 0x2c ---------------------------------- */
980 [BTTV_BOARD_SIGMA_TVII_FM] = {
981 .name = "Sigma TVII-FM",
982 .video_inputs = 2,
983 /* .audio_inputs= 1, */
984 .svhs = NO_SVHS,
985 .gpiomask = 3,
986 .muxsel = MUXSEL(2, 3, 1, 1),
987 .gpiomux = { 1, 1, 0, 2 },
988 .gpiomute = 3,
989 .no_msp34xx = 1,
990 .pll = PLL_NONE,
991 .tuner_type = UNSET,
992 .tuner_addr = ADDR_UNSET,
993 },
994 [BTTV_BOARD_MATRIX_VISION2] = {
995 .name = "MATRIX-Vision MV-Delta 2",
996 .video_inputs = 5,
997 /* .audio_inputs= 1, */
998 .svhs = 3,
999 .gpiomask = 0,
1000 .muxsel = MUXSEL(2, 3, 1, 0, 0),
1001 .gpiomux = { 0 },
1002 .no_msp34xx = 1,
1003 .pll = PLL_28,
1004 .tuner_type = TUNER_ABSENT,
1005 .tuner_addr = ADDR_UNSET,
1006 },
1007 [BTTV_BOARD_ZOLTRIX_GENIE] = {
1008 .name = "Zoltrix Genie TV/FM",
1009 .video_inputs = 3,
1010 /* .audio_inputs= 1, */
1011 .svhs = 2,
1012 .gpiomask = 0xbcf03f,
1013 .muxsel = MUXSEL(2, 3, 1, 1),
1014 .gpiomux = { 0xbc803f, 0xbc903f, 0xbcb03f, 0 },
1015 .gpiomute = 0xbcb03f,
1016 .no_msp34xx = 1,
1017 .pll = PLL_28,
1018 .tuner_type = TUNER_TEMIC_4039FR5_NTSC,
1019 .tuner_addr = ADDR_UNSET,
1020 },
1021 [BTTV_BOARD_TERRATVRADIO] = {
1022 .name = "Terratec TV/Radio+",
1023 .video_inputs = 3,
1024 /* .audio_inputs= 1, */
1025 .svhs = 2,
1026 .gpiomask = 0x70000,
1027 .muxsel = MUXSEL(2, 3, 1, 1),
1028 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
1029 .gpiomute = 0x40000,
1030 .no_msp34xx = 1,
1031 .pll = PLL_35,
1032 .tuner_type = TUNER_PHILIPS_PAL_I,
1033 .tuner_addr = ADDR_UNSET,
1034 .has_radio = 1,
1035 },
1036
1037 /* ---- card 0x30 ---------------------------------- */
1038 [BTTV_BOARD_DYNALINK] = {
1039 .name = "Askey CPH03x/ Dynalink Magic TView",
1040 .video_inputs = 3,
1041 /* .audio_inputs= 1, */
1042 .svhs = 2,
1043 .gpiomask = 15,
1044 .muxsel = MUXSEL(2, 3, 1, 1),
1045 .gpiomux = {2,0,0,0 },
1046 .gpiomute = 1,
1047 .pll = PLL_28,
1048 .tuner_type = UNSET,
1049 .tuner_addr = ADDR_UNSET,
1050 },
1051 [BTTV_BOARD_GVBCTV3PCI] = {
1052 .name = "IODATA GV-BCTV3/PCI",
1053 .video_inputs = 3,
1054 /* .audio_inputs= 1, */
1055 .svhs = 2,
1056 .gpiomask = 0x010f00,
1057 .muxsel = MUXSEL(2, 3, 0, 0),
1058 .gpiomux = {0x10000, 0, 0x10000, 0 },
1059 .no_msp34xx = 1,
1060 .pll = PLL_28,
1061 .tuner_type = TUNER_ALPS_TSHC6_NTSC,
1062 .tuner_addr = ADDR_UNSET,
1063 .audio_mode_gpio= gvbctv3pci_audio,
1064 },
1065 [BTTV_BOARD_PXELVWPLTVPAK] = {
1066 .name = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP",
1067 .video_inputs = 5,
1068 /* .audio_inputs= 1, */
1069 .svhs = 3,
1070 .has_dig_in = 1,
1071 .gpiomask = 0xAA0000,
1072 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */
1073 /* .digital_mode= DIGITAL_MODE_CAMERA, */
1074 .gpiomux = { 0x20000, 0, 0x80000, 0x80000 },
1075 .gpiomute = 0xa8000,
1076 .no_msp34xx = 1,
1077 .pll = PLL_28,
1078 .tuner_type = TUNER_PHILIPS_PAL_I,
1079 .tuner_addr = ADDR_UNSET,
1080 .has_remote = 1,
1081 /* GPIO wiring: (different from Rev.4C !)
1082 GPIO17: U4.A0 (first hef4052bt)
1083 GPIO19: U4.A1
1084 GPIO20: U5.A1 (second hef4052bt)
1085 GPIO21: U4.nEN
1086 GPIO22: BT832 Reset Line
1087 GPIO23: A5,A0, U5,nEN
1088 Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22
1089 */
1090 },
1091 [BTTV_BOARD_EAGLE] = {
1092 .name = "Eagle Wireless Capricorn2 (bt878A)",
1093 .video_inputs = 4,
1094 /* .audio_inputs= 1, */
1095 .svhs = 2,
1096 .gpiomask = 7,
1097 .muxsel = MUXSEL(2, 0, 1, 1),
1098 .gpiomux = { 0, 1, 2, 3 },
1099 .gpiomute = 4,
1100 .pll = PLL_28,
1101 .tuner_type = UNSET /* TUNER_ALPS_TMDH2_NTSC */,
1102 .tuner_addr = ADDR_UNSET,
1103 },
1104
1105 /* ---- card 0x34 ---------------------------------- */
1106 [BTTV_BOARD_PINNACLEPRO] = {
1107 /* David Härdeman <david@2gen.com> */
1108 .name = "Pinnacle PCTV Studio Pro",
1109 .video_inputs = 4,
1110 /* .audio_inputs= 1, */
1111 .svhs = 3,
1112 .gpiomask = 0x03000F,
1113 .muxsel = MUXSEL(2, 3, 1, 1),
1114 .gpiomux = { 1, 0xd0001, 0, 0 },
1115 .gpiomute = 10,
1116 /* sound path (5 sources):
1117 MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable)
1118 0= ext. Audio IN
1119 1= from MUX2
1120 2= Mono TV sound from Tuner
1121 3= not connected
1122 MUX2 (mask 0x30000):
1123 0,2,3= from MSP34xx
1124 1= FM stereo Radio from Tuner */
1125 .pll = PLL_28,
1126 .tuner_type = UNSET,
1127 .tuner_addr = ADDR_UNSET,
1128 },
1129 [BTTV_BOARD_TVIEW_RDS_FM] = {
1130 /* Claas Langbehn <claas@bigfoot.com>,
1131 Sven Grothklags <sven@upb.de> */
1132 .name = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS",
1133 .video_inputs = 4,
1134 /* .audio_inputs= 3, */
1135 .svhs = 2,
1136 .gpiomask = 0x1c,
1137 .muxsel = MUXSEL(2, 3, 1, 1),
1138 .gpiomux = { 0, 0, 0x10, 8 },
1139 .gpiomute = 4,
1140 .pll = PLL_28,
1141 .tuner_type = TUNER_PHILIPS_PAL,
1142 .tuner_addr = ADDR_UNSET,
1143 .has_radio = 1,
1144 },
1145 [BTTV_BOARD_LIFETEC_9415] = {
1146 /* Tim Röstermundt <rosterm@uni-muenster.de>
1147 in de.comp.os.unix.linux.hardware:
1148 options bttv card=0 pll=1 radio=1 gpiomask=0x18e0
1149 gpiomux =0x44c71f,0x44d71f,0,0x44d71f,0x44dfff
1150 options tuner type=5 */
1151 .name = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]",
1152 .video_inputs = 4,
1153 /* .audio_inputs= 1, */
1154 .svhs = 2,
1155 .gpiomask = 0x18e0,
1156 .muxsel = MUXSEL(2, 3, 1, 1),
1157 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1158 .gpiomute = 0x18e0,
1159 /* For cards with tda9820/tda9821:
1160 0x0000: Tuner normal stereo
1161 0x0080: Tuner A2 SAP (second audio program = Zweikanalton)
1162 0x0880: Tuner A2 stereo */
1163 .pll = PLL_28,
1164 .tuner_type = UNSET,
1165 .tuner_addr = ADDR_UNSET,
1166 },
1167 [BTTV_BOARD_BESTBUY_EASYTV] = {
1168 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1169 old Easy TV BT848 version (model CPH031) */
1170 .name = "Askey CPH031/ BESTBUY Easy TV",
1171 .video_inputs = 4,
1172 /* .audio_inputs= 1, */
1173 .svhs = 2,
1174 .gpiomask = 0xF,
1175 .muxsel = MUXSEL(2, 3, 1, 0),
1176 .gpiomux = { 2, 0, 0, 0 },
1177 .gpiomute = 10,
1178 .pll = PLL_28,
1179 .tuner_type = TUNER_TEMIC_PAL,
1180 .tuner_addr = ADDR_UNSET,
1181 },
1182
1183 /* ---- card 0x38 ---------------------------------- */
1184 [BTTV_BOARD_FLYVIDEO_98FM] = {
1185 /* Gordon Heydon <gjheydon@bigfoot.com ('98) */
1186 .name = "Lifeview FlyVideo 98FM LR50",
1187 .video_inputs = 4,
1188 /* .audio_inputs= 3, */
1189 .svhs = 2,
1190 .gpiomask = 0x1800,
1191 .muxsel = MUXSEL(2, 3, 1, 1),
1192 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
1193 .gpiomute = 0x1800,
1194 .pll = PLL_28,
1195 .tuner_type = TUNER_PHILIPS_PAL,
1196 .tuner_addr = ADDR_UNSET,
1197 },
1198 /* This is the ultimate cheapo capture card
1199 * just a BT848A on a small PCB!
1200 * Steve Hosgood <steve@equiinet.com> */
1201 [BTTV_BOARD_GRANDTEC] = {
1202 .name = "GrandTec 'Grand Video Capture' (Bt848)",
1203 .video_inputs = 2,
1204 /* .audio_inputs= 0, */
1205 .svhs = 1,
1206 .gpiomask = 0,
1207 .muxsel = MUXSEL(3, 1),
1208 .gpiomux = { 0 },
1209 .no_msp34xx = 1,
1210 .pll = PLL_35,
1211 .tuner_type = TUNER_ABSENT,
1212 .tuner_addr = ADDR_UNSET,
1213 },
1214 [BTTV_BOARD_ASKEY_CPH060] = {
1215 /* Daniel Herrington <daniel.herrington@home.com> */
1216 .name = "Askey CPH060/ Phoebe TV Master Only (No FM)",
1217 .video_inputs = 3,
1218 /* .audio_inputs= 1, */
1219 .svhs = 2,
1220 .gpiomask = 0xe00,
1221 .muxsel = MUXSEL(2, 3, 1, 1),
1222 .gpiomux = { 0x400, 0x400, 0x400, 0x400 },
1223 .gpiomute = 0x800,
1224 .pll = PLL_28,
1225 .tuner_type = TUNER_TEMIC_4036FY5_NTSC,
1226 .tuner_addr = ADDR_UNSET,
1227 },
1228 [BTTV_BOARD_ASKEY_CPH03X] = {
1229 /* Matti Mottus <mottus@physic.ut.ee> */
1230 .name = "Askey CPH03x TV Capturer",
1231 .video_inputs = 4,
1232 /* .audio_inputs= 1, */
1233 .svhs = 2,
1234 .gpiomask = 0x03000F,
1235 .muxsel = MUXSEL(2, 3, 1, 0),
1236 .gpiomux = { 2, 0, 0, 0 },
1237 .gpiomute = 1,
1238 .pll = PLL_28,
1239 .tuner_type = TUNER_TEMIC_PAL,
1240 .tuner_addr = ADDR_UNSET,
1241 .has_remote = 1,
1242 },
1243
1244 /* ---- card 0x3c ---------------------------------- */
1245 [BTTV_BOARD_MM100PCTV] = {
1246 /* Philip Blundell <philb@gnu.org> */
1247 .name = "Modular Technology MM100PCTV",
1248 .video_inputs = 2,
1249 /* .audio_inputs= 2, */
1250 .svhs = NO_SVHS,
1251 .gpiomask = 11,
1252 .muxsel = MUXSEL(2, 3, 1, 1),
1253 .gpiomux = { 2, 0, 0, 1 },
1254 .gpiomute = 8,
1255 .pll = PLL_35,
1256 .tuner_type = TUNER_TEMIC_PAL,
1257 .tuner_addr = ADDR_UNSET,
1258 },
1259 [BTTV_BOARD_GMV1] = {
1260 /* Adrian Cox <adrian@humboldt.co.uk */
1261 .name = "AG Electronics GMV1",
1262 .video_inputs = 2,
1263 /* .audio_inputs= 0, */
1264 .svhs = 1,
1265 .gpiomask = 0xF,
1266 .muxsel = MUXSEL(2, 2),
1267 .gpiomux = { },
1268 .no_msp34xx = 1,
1269 .pll = PLL_28,
1270 .tuner_type = TUNER_ABSENT,
1271 .tuner_addr = ADDR_UNSET,
1272 },
1273 [BTTV_BOARD_BESTBUY_EASYTV2] = {
1274 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1275 new Easy TV BT878 version (model CPH061)
1276 special thanks to Informatica Mieres for providing the card */
1277 .name = "Askey CPH061/ BESTBUY Easy TV (bt878)",
1278 .video_inputs = 3,
1279 /* .audio_inputs= 2, */
1280 .svhs = 2,
1281 .gpiomask = 0xFF,
1282 .muxsel = MUXSEL(2, 3, 1, 0),
1283 .gpiomux = { 1, 0, 4, 4 },
1284 .gpiomute = 9,
1285 .pll = PLL_28,
1286 .tuner_type = TUNER_PHILIPS_PAL,
1287 .tuner_addr = ADDR_UNSET,
1288 },
1289 [BTTV_BOARD_ATI_TVWONDER] = {
1290 /* Lukas Gebauer <geby@volny.cz> */
1291 .name = "ATI TV-Wonder",
1292 .video_inputs = 3,
1293 /* .audio_inputs= 1, */
1294 .svhs = 2,
1295 .gpiomask = 0xf03f,
1296 .muxsel = MUXSEL(2, 3, 1, 0),
1297 .gpiomux = { 0xbffe, 0, 0xbfff, 0 },
1298 .gpiomute = 0xbffe,
1299 .pll = PLL_28,
1300 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1301 .tuner_addr = ADDR_UNSET,
1302 },
1303
1304 /* ---- card 0x40 ---------------------------------- */
1305 [BTTV_BOARD_ATI_TVWONDERVE] = {
1306 /* Lukas Gebauer <geby@volny.cz> */
1307 .name = "ATI TV-Wonder VE",
1308 .video_inputs = 2,
1309 /* .audio_inputs= 1, */
1310 .svhs = NO_SVHS,
1311 .gpiomask = 1,
1312 .muxsel = MUXSEL(2, 3, 0, 1),
1313 .gpiomux = { 0, 0, 1, 0 },
1314 .no_msp34xx = 1,
1315 .pll = PLL_28,
1316 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1317 .tuner_addr = ADDR_UNSET,
1318 },
1319 [BTTV_BOARD_FLYVIDEO2000] = {
1320 /* DeeJay <deejay@westel900.net (2000S) */
1321 .name = "Lifeview FlyVideo 2000S LR90",
1322 .video_inputs = 3,
1323 /* .audio_inputs= 3, */
1324 .svhs = 2,
1325 .gpiomask = 0x18e0,
1326 .muxsel = MUXSEL(2, 3, 0, 1),
1327 /* Radio changed from 1e80 to 0x800 to make
1328 FlyVideo2000S in .hu happy (gm)*/
1329 /* -dk-???: set mute=0x1800 for tda9874h daughterboard */
1330 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1331 .gpiomute = 0x1800,
1332 .audio_mode_gpio= fv2000s_audio,
1333 .no_msp34xx = 1,
1334 .pll = PLL_28,
1335 .tuner_type = TUNER_PHILIPS_PAL,
1336 .tuner_addr = ADDR_UNSET,
1337 },
1338 [BTTV_BOARD_TERRATVALUER] = {
1339 .name = "Terratec TValueRadio",
1340 .video_inputs = 3,
1341 /* .audio_inputs= 1, */
1342 .svhs = 2,
1343 .gpiomask = 0xffff00,
1344 .muxsel = MUXSEL(2, 3, 1, 1),
1345 .gpiomux = { 0x500, 0x500, 0x300, 0x900 },
1346 .gpiomute = 0x900,
1347 .pll = PLL_28,
1348 .tuner_type = TUNER_PHILIPS_PAL,
1349 .tuner_addr = ADDR_UNSET,
1350 .has_radio = 1,
1351 },
1352 [BTTV_BOARD_GVBCTV4PCI] = {
1353 /* TANAKA Kei <peg00625@nifty.com> */
1354 .name = "IODATA GV-BCTV4/PCI",
1355 .video_inputs = 3,
1356 /* .audio_inputs= 1, */
1357 .svhs = 2,
1358 .gpiomask = 0x010f00,
1359 .muxsel = MUXSEL(2, 3, 0, 0),
1360 .gpiomux = {0x10000, 0, 0x10000, 0 },
1361 .no_msp34xx = 1,
1362 .pll = PLL_28,
1363 .tuner_type = TUNER_SHARP_2U5JF5540_NTSC,
1364 .tuner_addr = ADDR_UNSET,
1365 .audio_mode_gpio= gvbctv3pci_audio,
1366 },
1367
1368 /* ---- card 0x44 ---------------------------------- */
1369 [BTTV_BOARD_VOODOOTV_FM] = {
1370 .name = "3Dfx VoodooTV FM (Euro)",
1371 /* try "insmod msp3400 simple=0" if you have
1372 * sound problems with this card. */
1373 .video_inputs = 4,
1374 /* .audio_inputs= 1, */
1375 .svhs = NO_SVHS,
1376 .gpiomask = 0x4f8a00,
1377 /* 0x100000: 1=MSP enabled (0=disable again)
1378 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1379 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1380 .gpiomute = 0x947fff,
1381 /* tvtuner, radio, external,internal, mute, stereo
1382 * tuner, Composite, SVid, Composite-on-Svid-adapter */
1383 .muxsel = MUXSEL(2, 3, 0, 1),
1384 .tuner_type = TUNER_MT2032,
1385 .tuner_addr = ADDR_UNSET,
1386 .pll = PLL_28,
1387 .has_radio = 1,
1388 },
1389 [BTTV_BOARD_VOODOOTV_200] = {
1390 .name = "VoodooTV 200 (USA)",
1391 /* try "insmod msp3400 simple=0" if you have
1392 * sound problems with this card. */
1393 .video_inputs = 4,
1394 /* .audio_inputs= 1, */
1395 .svhs = NO_SVHS,
1396 .gpiomask = 0x4f8a00,
1397 /* 0x100000: 1=MSP enabled (0=disable again)
1398 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1399 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1400 .gpiomute = 0x947fff,
1401 /* tvtuner, radio, external,internal, mute, stereo
1402 * tuner, Composite, SVid, Composite-on-Svid-adapter */
1403 .muxsel = MUXSEL(2, 3, 0, 1),
1404 .tuner_type = TUNER_MT2032,
1405 .tuner_addr = ADDR_UNSET,
1406 .pll = PLL_28,
1407 .has_radio = 1,
1408 },
1409 [BTTV_BOARD_AIMMS] = {
1410 /* Philip Blundell <pb@nexus.co.uk> */
1411 .name = "Active Imaging AIMMS",
1412 .video_inputs = 1,
1413 /* .audio_inputs= 0, */
1414 .tuner_type = TUNER_ABSENT,
1415 .tuner_addr = ADDR_UNSET,
1416 .pll = PLL_28,
1417 .muxsel = MUXSEL(2),
1418 .gpiomask = 0
1419 },
1420 [BTTV_BOARD_PV_BT878P_PLUS] = {
1421 /* Tomasz Pyra <hellfire@sedez.iq.pl> */
1422 .name = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)",
1423 .video_inputs = 3,
1424 /* .audio_inputs= 4, */
1425 .svhs = 2,
1426 .gpiomask = 15,
1427 .muxsel = MUXSEL(2, 3, 1, 1),
1428 .gpiomux = { 0, 0, 11, 7 }, /* TV and Radio with same GPIO ! */
1429 .gpiomute = 13,
1430 .pll = PLL_28,
1431 .tuner_type = TUNER_LG_PAL_I_FM,
1432 .tuner_addr = ADDR_UNSET,
1433 .has_remote = 1,
1434 /* GPIO wiring:
1435 GPIO0: U4.A0 (hef4052bt)
1436 GPIO1: U4.A1
1437 GPIO2: U4.A1 (second hef4052bt)
1438 GPIO3: U4.nEN, U5.A0, A5.nEN
1439 GPIO8-15: vrd866b ?
1440 */
1441 },
1442 [BTTV_BOARD_FLYVIDEO98EZ] = {
1443 .name = "Lifeview FlyVideo 98EZ (capture only) LR51",
1444 .video_inputs = 4,
1445 /* .audio_inputs= 0, */
1446 .svhs = 2,
1447 /* AV1, AV2, SVHS, CVid adapter on SVHS */
1448 .muxsel = MUXSEL(2, 3, 1, 1),
1449 .pll = PLL_28,
1450 .no_msp34xx = 1,
1451 .tuner_type = TUNER_ABSENT,
1452 .tuner_addr = ADDR_UNSET,
1453 },
1454
1455 /* ---- card 0x48 ---------------------------------- */
1456 [BTTV_BOARD_PV_BT878P_9B] = {
1457 /* Dariusz Kowalewski <darekk@automex.pl> */
1458 .name = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)",
1459 .video_inputs = 4,
1460 /* .audio_inputs= 1, */
1461 .svhs = 2,
1462 .gpiomask = 0x3f,
1463 .muxsel = MUXSEL(2, 3, 1, 1),
1464 .gpiomux = { 0x01, 0x00, 0x03, 0x03 },
1465 .gpiomute = 0x09,
1466 .no_msp34xx = 1,
1467 .pll = PLL_28,
1468 .tuner_type = TUNER_PHILIPS_PAL,
1469 .tuner_addr = ADDR_UNSET,
1470 .audio_mode_gpio= pvbt878p9b_audio, /* Note: not all cards have stereo */
1471 .has_radio = 1, /* Note: not all cards have radio */
1472 .has_remote = 1,
1473 /* GPIO wiring:
1474 GPIO0: A0 hef4052
1475 GPIO1: A1 hef4052
1476 GPIO3: nEN hef4052
1477 GPIO8-15: vrd866b
1478 GPIO20,22,23: R30,R29,R28
1479 */
1480 },
1481 [BTTV_BOARD_SENSORAY311_611] = {
1482 /* Clay Kunz <ckunz@mail.arc.nasa.gov> */
1483 /* you must jumper JP5 for the 311 card (PC/104+) to work */
1484 .name = "Sensoray 311/611",
1485 .video_inputs = 5,
1486 /* .audio_inputs= 0, */
1487 .svhs = 4,
1488 .gpiomask = 0,
1489 .muxsel = MUXSEL(2, 3, 1, 0, 0),
1490 .gpiomux = { 0 },
1491 .tuner_type = TUNER_ABSENT,
1492 .tuner_addr = ADDR_UNSET,
1493 },
1494 [BTTV_BOARD_RV605] = {
1495 /* Miguel Freitas <miguel@cetuc.puc-rio.br> */
1496 .name = "RemoteVision MX (RV605)",
1497 .video_inputs = 16,
1498 /* .audio_inputs= 0, */
1499 .svhs = NO_SVHS,
1500 .gpiomask = 0x00,
1501 .gpiomask2 = 0x07ff,
1502 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
1503 .no_msp34xx = 1,
1504 .tuner_type = TUNER_ABSENT,
1505 .tuner_addr = ADDR_UNSET,
1506 .muxsel_hook = rv605_muxsel,
1507 },
1508 [BTTV_BOARD_POWERCLR_MTV878] = {
1509 .name = "Powercolor MTV878/ MTV878R/ MTV878F",
1510 .video_inputs = 3,
1511 /* .audio_inputs= 2, */
1512 .svhs = 2,
1513 .gpiomask = 0x1C800F, /* Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset */
1514 .muxsel = MUXSEL(2, 1, 1),
1515 .gpiomux = { 0, 1, 2, 2 },
1516 .gpiomute = 4,
1517 .tuner_type = TUNER_PHILIPS_PAL,
1518 .tuner_addr = ADDR_UNSET,
1519 .pll = PLL_28,
1520 .has_radio = 1,
1521 },
1522
1523 /* ---- card 0x4c ---------------------------------- */
1524 [BTTV_BOARD_WINDVR] = {
1525 /* Masaki Suzuki <masaki@btree.org> */
1526 .name = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)",
1527 .video_inputs = 3,
1528 /* .audio_inputs= 1, */
1529 .svhs = 2,
1530 .gpiomask = 0x140007,
1531 .muxsel = MUXSEL(2, 3, 1, 1),
1532 .gpiomux = { 0, 1, 2, 3 },
1533 .gpiomute = 4,
1534 .tuner_type = TUNER_PHILIPS_NTSC,
1535 .tuner_addr = ADDR_UNSET,
1536 .audio_mode_gpio= windvr_audio,
1537 },
1538 [BTTV_BOARD_GRANDTEC_MULTI] = {
1539 .name = "GrandTec Multi Capture Card (Bt878)",
1540 .video_inputs = 4,
1541 /* .audio_inputs= 0, */
1542 .svhs = NO_SVHS,
1543 .gpiomask = 0,
1544 .muxsel = MUXSEL(2, 3, 1, 0),
1545 .gpiomux = { 0 },
1546 .no_msp34xx = 1,
1547 .pll = PLL_28,
1548 .tuner_type = TUNER_ABSENT,
1549 .tuner_addr = ADDR_UNSET,
1550 },
1551 [BTTV_BOARD_KWORLD] = {
1552 .name = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF",
1553 .video_inputs = 4,
1554 /* .audio_inputs= 3, */
1555 .svhs = 2,
1556 .gpiomask = 7,
1557 /* Tuner, SVid, SVHS, SVid to SVHS connector */
1558 .muxsel = MUXSEL(2, 3, 1, 1),
1559 .gpiomux = { 0, 0, 4, 4 },/* Yes, this tuner uses the same audio output for TV and FM radio!
1560 * This card lacks external Audio In, so we mute it on Ext. & Int.
1561 * The PCB can take a sbx1637/sbx1673, wiring unknown.
1562 * This card lacks PCI subsystem ID, sigh.
1563 * gpiomux =1: lower volume, 2+3: mute
1564 * btwincap uses 0x80000/0x80003
1565 */
1566 .gpiomute = 4,
1567 .no_msp34xx = 1,
1568 .pll = PLL_28,
1569 .tuner_type = TUNER_PHILIPS_PAL,
1570 .tuner_addr = ADDR_UNSET,
1571 /* Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and
1572 radio signal strength indicators work fine. */
1573 .has_radio = 1,
1574 /* GPIO Info:
1575 GPIO0,1: HEF4052 A0,A1
1576 GPIO2: HEF4052 nENABLE
1577 GPIO3-7: n.c.
1578 GPIO8-13: IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card]
1579 GPIO14,15: ??
1580 GPIO16-21: n.c.
1581 GPIO22,23: ??
1582 ?? : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/
1583 },
1584 [BTTV_BOARD_DSP_TCVIDEO] = {
1585 /* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */
1586 .name = "DSP Design TCVIDEO",
1587 .video_inputs = 4,
1588 .svhs = NO_SVHS,
1589 .muxsel = MUXSEL(2, 3, 1, 0),
1590 .pll = PLL_28,
1591 .tuner_type = UNSET,
1592 .tuner_addr = ADDR_UNSET,
1593 },
1594
1595 /* ---- card 0x50 ---------------------------------- */
1596 [BTTV_BOARD_HAUPPAUGEPVR] = {
1597 .name = "Hauppauge WinTV PVR",
1598 .video_inputs = 4,
1599 /* .audio_inputs= 1, */
1600 .svhs = 2,
1601 .muxsel = MUXSEL(2, 0, 1, 1),
1602 .pll = PLL_28,
1603 .tuner_type = UNSET,
1604 .tuner_addr = ADDR_UNSET,
1605
1606 .gpiomask = 7,
1607 .gpiomux = {7},
1608 },
1609 [BTTV_BOARD_GVBCTV5PCI] = {
1610 .name = "IODATA GV-BCTV5/PCI",
1611 .video_inputs = 3,
1612 /* .audio_inputs= 1, */
1613 .svhs = 2,
1614 .gpiomask = 0x0f0f80,
1615 .muxsel = MUXSEL(2, 3, 1, 0),
1616 .gpiomux = {0x030000, 0x010000, 0, 0 },
1617 .gpiomute = 0x020000,
1618 .no_msp34xx = 1,
1619 .pll = PLL_28,
1620 .tuner_type = TUNER_PHILIPS_NTSC_M,
1621 .tuner_addr = ADDR_UNSET,
1622 .audio_mode_gpio= gvbctv5pci_audio,
1623 .has_radio = 1,
1624 },
1625 [BTTV_BOARD_OSPREY1x0] = {
1626 .name = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */
1627 .video_inputs = 4, /* id-inputs-clock */
1628 /* .audio_inputs= 0, */
1629 .svhs = 3,
1630 .muxsel = MUXSEL(3, 2, 0, 1),
1631 .pll = PLL_28,
1632 .tuner_type = TUNER_ABSENT,
1633 .tuner_addr = ADDR_UNSET,
1634 .no_msp34xx = 1,
1635 .no_tda7432 = 1,
1636 },
1637 [BTTV_BOARD_OSPREY1x0_848] = {
1638 .name = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */
1639 .video_inputs = 3,
1640 /* .audio_inputs= 0, */
1641 .svhs = 2,
1642 .muxsel = MUXSEL(2, 3, 1),
1643 .pll = PLL_28,
1644 .tuner_type = TUNER_ABSENT,
1645 .tuner_addr = ADDR_UNSET,
1646 .no_msp34xx = 1,
1647 .no_tda7432 = 1,
1648 },
1649
1650 /* ---- card 0x54 ---------------------------------- */
1651 [BTTV_BOARD_OSPREY101_848] = {
1652 .name = "Osprey 101 (848)", /* 0x05-40C0-C1 */
1653 .video_inputs = 2,
1654 /* .audio_inputs= 0, */
1655 .svhs = 1,
1656 .muxsel = MUXSEL(3, 1),
1657 .pll = PLL_28,
1658 .tuner_type = TUNER_ABSENT,
1659 .tuner_addr = ADDR_UNSET,
1660 .no_msp34xx = 1,
1661 .no_tda7432 = 1,
1662 },
1663 [BTTV_BOARD_OSPREY1x1] = {
1664 .name = "Osprey 101/151", /* 0x1(4|5)-0004-C4 */
1665 .video_inputs = 1,
1666 /* .audio_inputs= 0, */
1667 .svhs = NO_SVHS,
1668 .muxsel = MUXSEL(0),
1669 .pll = PLL_28,
1670 .tuner_type = TUNER_ABSENT,
1671 .tuner_addr = ADDR_UNSET,
1672 .no_msp34xx = 1,
1673 .no_tda7432 = 1,
1674 },
1675 [BTTV_BOARD_OSPREY1x1_SVID] = {
1676 .name = "Osprey 101/151 w/ svid", /* 0x(16|17|20)-00C4-C1 */
1677 .video_inputs = 2,
1678 /* .audio_inputs= 0, */
1679 .svhs = 1,
1680 .muxsel = MUXSEL(0, 1),
1681 .pll = PLL_28,
1682 .tuner_type = TUNER_ABSENT,
1683 .tuner_addr = ADDR_UNSET,
1684 .no_msp34xx = 1,
1685 .no_tda7432 = 1,
1686 },
1687 [BTTV_BOARD_OSPREY2xx] = {
1688 .name = "Osprey 200/201/250/251", /* 0x1(8|9|E|F)-0004-C4 */
1689 .video_inputs = 1,
1690 /* .audio_inputs= 1, */
1691 .svhs = NO_SVHS,
1692 .muxsel = MUXSEL(0),
1693 .pll = PLL_28,
1694 .tuner_type = TUNER_ABSENT,
1695 .tuner_addr = ADDR_UNSET,
1696 .no_msp34xx = 1,
1697 .no_tda7432 = 1,
1698 },
1699
1700 /* ---- card 0x58 ---------------------------------- */
1701 [BTTV_BOARD_OSPREY2x0_SVID] = {
1702 .name = "Osprey 200/250", /* 0x1(A|B)-00C4-C1 */
1703 .video_inputs = 2,
1704 /* .audio_inputs= 1, */
1705 .svhs = 1,
1706 .muxsel = MUXSEL(0, 1),
1707 .pll = PLL_28,
1708 .tuner_type = TUNER_ABSENT,
1709 .tuner_addr = ADDR_UNSET,
1710 .no_msp34xx = 1,
1711 .no_tda7432 = 1,
1712 },
1713 [BTTV_BOARD_OSPREY2x0] = {
1714 .name = "Osprey 210/220/230", /* 0x1(A|B)-04C0-C1 */
1715 .video_inputs = 2,
1716 /* .audio_inputs= 1, */
1717 .svhs = 1,
1718 .muxsel = MUXSEL(2, 3),
1719 .pll = PLL_28,
1720 .tuner_type = TUNER_ABSENT,
1721 .tuner_addr = ADDR_UNSET,
1722 .no_msp34xx = 1,
1723 .no_tda7432 = 1,
1724 },
1725 [BTTV_BOARD_OSPREY500] = {
1726 .name = "Osprey 500", /* 500 */
1727 .video_inputs = 2,
1728 /* .audio_inputs= 1, */
1729 .svhs = 1,
1730 .muxsel = MUXSEL(2, 3),
1731 .pll = PLL_28,
1732 .tuner_type = TUNER_ABSENT,
1733 .tuner_addr = ADDR_UNSET,
1734 .no_msp34xx = 1,
1735 .no_tda7432 = 1,
1736 },
1737 [BTTV_BOARD_OSPREY540] = {
1738 .name = "Osprey 540", /* 540 */
1739 .video_inputs = 4,
1740 /* .audio_inputs= 1, */
1741 .pll = PLL_28,
1742 .tuner_type = TUNER_ABSENT,
1743 .tuner_addr = ADDR_UNSET,
1744 .no_msp34xx = 1,
1745 .no_tda7432 = 1,
1746 },
1747
1748 /* ---- card 0x5C ---------------------------------- */
1749 [BTTV_BOARD_OSPREY2000] = {
1750 .name = "Osprey 2000", /* 2000 */
1751 .video_inputs = 2,
1752 /* .audio_inputs= 1, */
1753 .svhs = 1,
1754 .muxsel = MUXSEL(2, 3),
1755 .pll = PLL_28,
1756 .tuner_type = TUNER_ABSENT,
1757 .tuner_addr = ADDR_UNSET,
1758 .no_msp34xx = 1,
1759 .no_tda7432 = 1, /* must avoid, conflicts with the bt860 */
1760 },
1761 [BTTV_BOARD_IDS_EAGLE] = {
1762 /* M G Berberich <berberic@forwiss.uni-passau.de> */
1763 .name = "IDS Eagle",
1764 .video_inputs = 4,
1765 /* .audio_inputs= 0, */
1766 .tuner_type = TUNER_ABSENT,
1767 .tuner_addr = ADDR_UNSET,
1768 .svhs = NO_SVHS,
1769 .gpiomask = 0,
1770 .muxsel = MUXSEL(2, 2, 2, 2),
1771 .muxsel_hook = eagle_muxsel,
1772 .no_msp34xx = 1,
1773 .pll = PLL_28,
1774 },
1775 [BTTV_BOARD_PINNACLESAT] = {
1776 .name = "Pinnacle PCTV Sat",
1777 .video_inputs = 2,
1778 /* .audio_inputs= 0, */
1779 .svhs = 1,
1780 .tuner_type = TUNER_ABSENT,
1781 .tuner_addr = ADDR_UNSET,
1782 .no_msp34xx = 1,
1783 .no_tda7432 = 1,
1784 .muxsel = MUXSEL(3, 1),
1785 .pll = PLL_28,
1786 .no_gpioirq = 1,
1787 .has_dvb = 1,
1788 },
1789 [BTTV_BOARD_FORMAC_PROTV] = {
1790 .name = "Formac ProTV II (bt878)",
1791 .video_inputs = 4,
1792 /* .audio_inputs= 1, */
1793 .svhs = 3,
1794 .gpiomask = 2,
1795 /* TV, Comp1, Composite over SVID con, SVID */
1796 .muxsel = MUXSEL(2, 3, 1, 1),
1797 .gpiomux = { 2, 2, 0, 0 },
1798 .pll = PLL_28,
1799 .has_radio = 1,
1800 .tuner_type = TUNER_PHILIPS_PAL,
1801 .tuner_addr = ADDR_UNSET,
1802 /* sound routing:
1803 GPIO=0x00,0x01,0x03: mute (?)
1804 0x02: both TV and radio (tuner: FM1216/I)
1805 The card has onboard audio connectors labeled "cdrom" and "board",
1806 not soldered here, though unknown wiring.
1807 Card lacks: external audio in, pci subsystem id.
1808 */
1809 },
1810
1811 /* ---- card 0x60 ---------------------------------- */
1812 [BTTV_BOARD_MACHTV] = {
1813 .name = "MachTV",
1814 .video_inputs = 3,
1815 /* .audio_inputs= 1, */
1816 .svhs = NO_SVHS,
1817 .gpiomask = 7,
1818 .muxsel = MUXSEL(2, 3, 1, 1),
1819 .gpiomux = { 0, 1, 2, 3},
1820 .gpiomute = 4,
1821 .tuner_type = TUNER_PHILIPS_PAL,
1822 .tuner_addr = ADDR_UNSET,
1823 .pll = PLL_28,
1824 },
1825 [BTTV_BOARD_EURESYS_PICOLO] = {
1826 .name = "Euresys Picolo",
1827 .video_inputs = 3,
1828 /* .audio_inputs= 0, */
1829 .svhs = 2,
1830 .gpiomask = 0,
1831 .no_msp34xx = 1,
1832 .no_tda7432 = 1,
1833 .muxsel = MUXSEL(2, 0, 1),
1834 .pll = PLL_28,
1835 .tuner_type = TUNER_ABSENT,
1836 .tuner_addr = ADDR_UNSET,
1837 },
1838 [BTTV_BOARD_PV150] = {
1839 /* Luc Van Hoeylandt <luc@e-magic.be> */
1840 .name = "ProVideo PV150", /* 0x4f */
1841 .video_inputs = 2,
1842 /* .audio_inputs= 0, */
1843 .svhs = NO_SVHS,
1844 .gpiomask = 0,
1845 .muxsel = MUXSEL(2, 3),
1846 .gpiomux = { 0 },
1847 .no_msp34xx = 1,
1848 .pll = PLL_28,
1849 .tuner_type = TUNER_ABSENT,
1850 .tuner_addr = ADDR_UNSET,
1851 },
1852 [BTTV_BOARD_AD_TVK503] = {
1853 /* Hiroshi Takekawa <sian@big.or.jp> */
1854 /* This card lacks subsystem ID */
1855 .name = "AD-TVK503", /* 0x63 */
1856 .video_inputs = 4,
1857 /* .audio_inputs= 1, */
1858 .svhs = 2,
1859 .gpiomask = 0x001e8007,
1860 .muxsel = MUXSEL(2, 3, 1, 0),
1861 /* Tuner, Radio, external, internal, off, on */
1862 .gpiomux = { 0x08, 0x0f, 0x0a, 0x08 },
1863 .gpiomute = 0x0f,
1864 .no_msp34xx = 1,
1865 .pll = PLL_28,
1866 .tuner_type = TUNER_PHILIPS_NTSC,
1867 .tuner_addr = ADDR_UNSET,
1868 .audio_mode_gpio= adtvk503_audio,
1869 },
1870
1871 /* ---- card 0x64 ---------------------------------- */
1872 [BTTV_BOARD_HERCULES_SM_TV] = {
1873 .name = "Hercules Smart TV Stereo",
1874 .video_inputs = 4,
1875 /* .audio_inputs= 1, */
1876 .svhs = 2,
1877 .gpiomask = 0x00,
1878 .muxsel = MUXSEL(2, 3, 1, 1),
1879 .no_msp34xx = 1,
1880 .pll = PLL_28,
1881 .tuner_type = TUNER_PHILIPS_PAL,
1882 .tuner_addr = ADDR_UNSET,
1883 /* Notes:
1884 - card lacks subsystem ID
1885 - stereo variant w/ daughter board with tda9874a @0xb0
1886 - Audio Routing:
1887 always from tda9874 independent of GPIO (?)
1888 external line in: unknown
1889 - Other chips: em78p156elp @ 0x96 (probably IR remote control)
1890 hef4053 (instead 4052) for unknown function
1891 */
1892 },
1893 [BTTV_BOARD_PACETV] = {
1894 .name = "Pace TV & Radio Card",
1895 .video_inputs = 4,
1896 /* .audio_inputs= 1, */
1897 .svhs = 2,
1898 /* Tuner, CVid, SVid, CVid over SVid connector */
1899 .muxsel = MUXSEL(2, 3, 1, 1),
1900 .gpiomask = 0,
1901 .no_tda7432 = 1,
1902 .tuner_type = TUNER_PHILIPS_PAL_I,
1903 .tuner_addr = ADDR_UNSET,
1904 .has_radio = 1,
1905 .pll = PLL_28,
1906 /* Bt878, Bt832, FI1246 tuner; no pci subsystem id
1907 only internal line out: (4pin header) RGGL
1908 Radio must be decoded by msp3410d (not routed through)*/
1909 /*
1910 .digital_mode = DIGITAL_MODE_CAMERA, todo!
1911 */
1912 },
1913 [BTTV_BOARD_IVC200] = {
1914 /* Chris Willing <chris@vislab.usyd.edu.au> */
1915 .name = "IVC-200",
1916 .video_inputs = 1,
1917 /* .audio_inputs= 0, */
1918 .tuner_type = TUNER_ABSENT,
1919 .tuner_addr = ADDR_UNSET,
1920 .svhs = NO_SVHS,
1921 .gpiomask = 0xdf,
1922 .muxsel = MUXSEL(2),
1923 .pll = PLL_28,
1924 },
1925 [BTTV_BOARD_IVCE8784] = {
1926 .name = "IVCE-8784",
1927 .video_inputs = 1,
1928 /* .audio_inputs= 0, */
1929 .tuner_type = TUNER_ABSENT,
1930 .tuner_addr = ADDR_UNSET,
1931 .svhs = NO_SVHS,
1932 .gpiomask = 0xdf,
1933 .muxsel = MUXSEL(2),
1934 .pll = PLL_28,
1935 },
1936 [BTTV_BOARD_XGUARD] = {
1937 .name = "Grand X-Guard / Trust 814PCI",
1938 .video_inputs = 16,
1939 /* .audio_inputs= 0, */
1940 .svhs = NO_SVHS,
1941 .tuner_type = TUNER_ABSENT,
1942 .tuner_addr = ADDR_UNSET,
1943 .gpiomask2 = 0xff,
1944 .muxsel = MUXSEL(2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0),
1945 .muxsel_hook = xguard_muxsel,
1946 .no_msp34xx = 1,
1947 .no_tda7432 = 1,
1948 .pll = PLL_28,
1949 },
1950
1951 /* ---- card 0x68 ---------------------------------- */
1952 [BTTV_BOARD_NEBULA_DIGITV] = {
1953 .name = "Nebula Electronics DigiTV",
1954 .video_inputs = 1,
1955 .svhs = NO_SVHS,
1956 .muxsel = MUXSEL(2, 3, 1, 0),
1957 .no_msp34xx = 1,
1958 .no_tda7432 = 1,
1959 .pll = PLL_28,
1960 .tuner_type = TUNER_ABSENT,
1961 .tuner_addr = ADDR_UNSET,
1962 .has_dvb = 1,
1963 .has_remote = 1,
1964 .gpiomask = 0x1b,
1965 .no_gpioirq = 1,
1966 },
1967 [BTTV_BOARD_PV143] = {
1968 /* Jorge Boncompte - DTI2 <jorge@dti2.net> */
1969 .name = "ProVideo PV143",
1970 .video_inputs = 4,
1971 /* .audio_inputs= 0, */
1972 .svhs = NO_SVHS,
1973 .gpiomask = 0,
1974 .muxsel = MUXSEL(2, 3, 1, 0),
1975 .gpiomux = { 0 },
1976 .no_msp34xx = 1,
1977 .pll = PLL_28,
1978 .tuner_type = TUNER_ABSENT,
1979 .tuner_addr = ADDR_UNSET,
1980 },
1981 [BTTV_BOARD_VD009X1_VD011_MINIDIN] = {
1982 /* M.Klahr@phytec.de */
1983 .name = "PHYTEC VD-009-X1 VD-011 MiniDIN (bt878)",
1984 .video_inputs = 4,
1985 /* .audio_inputs= 0, */
1986 .svhs = 3,
1987 .gpiomask = 0x00,
1988 .muxsel = MUXSEL(2, 3, 1, 0),
1989 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
1990 .pll = PLL_28,
1991 .tuner_type = TUNER_ABSENT,
1992 .tuner_addr = ADDR_UNSET,
1993 },
1994 [BTTV_BOARD_VD009X1_VD011_COMBI] = {
1995 .name = "PHYTEC VD-009-X1 VD-011 Combi (bt878)",
1996 .video_inputs = 4,
1997 /* .audio_inputs= 0, */
1998 .svhs = 3,
1999 .gpiomask = 0x00,
2000 .muxsel = MUXSEL(2, 3, 1, 1),
2001 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2002 .pll = PLL_28,
2003 .tuner_type = TUNER_ABSENT,
2004 .tuner_addr = ADDR_UNSET,
2005 },
2006
2007 /* ---- card 0x6c ---------------------------------- */
2008 [BTTV_BOARD_VD009_MINIDIN] = {
2009 .name = "PHYTEC VD-009 MiniDIN (bt878)",
2010 .video_inputs = 10,
2011 /* .audio_inputs= 0, */
2012 .svhs = 9,
2013 .gpiomask = 0x00,
2014 .gpiomask2 = 0x03, /* used for external vodeo mux */
2015 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 0),
2016 .muxsel_hook = phytec_muxsel,
2017 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2018 .pll = PLL_28,
2019 .tuner_type = TUNER_ABSENT,
2020 .tuner_addr = ADDR_UNSET,
2021 },
2022 [BTTV_BOARD_VD009_COMBI] = {
2023 .name = "PHYTEC VD-009 Combi (bt878)",
2024 .video_inputs = 10,
2025 /* .audio_inputs= 0, */
2026 .svhs = 9,
2027 .gpiomask = 0x00,
2028 .gpiomask2 = 0x03, /* used for external vodeo mux */
2029 .muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1),
2030 .muxsel_hook = phytec_muxsel,
2031 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2032 .pll = PLL_28,
2033 .tuner_type = TUNER_ABSENT,
2034 .tuner_addr = ADDR_UNSET,
2035 },
2036 [BTTV_BOARD_IVC100] = {
2037 .name = "IVC-100",
2038 .video_inputs = 4,
2039 /* .audio_inputs= 0, */
2040 .tuner_type = TUNER_ABSENT,
2041 .tuner_addr = ADDR_UNSET,
2042 .svhs = NO_SVHS,
2043 .gpiomask = 0xdf,
2044 .muxsel = MUXSEL(2, 3, 1, 0),
2045 .pll = PLL_28,
2046 },
2047 [BTTV_BOARD_IVC120] = {
2048 /* IVC-120G - Alan Garfield <alan@fromorbit.com> */
2049 .name = "IVC-120G",
2050 .video_inputs = 16,
2051 /* .audio_inputs= 0, */
2052 .tuner_type = TUNER_ABSENT,
2053 .tuner_addr = ADDR_UNSET,
2054 .svhs = NO_SVHS, /* card has no svhs */
2055 .no_msp34xx = 1,
2056 .no_tda7432 = 1,
2057 .gpiomask = 0x00,
2058 .muxsel = MUXSEL(0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0),
2059 .muxsel_hook = ivc120_muxsel,
2060 .pll = PLL_28,
2061 },
2062
2063 /* ---- card 0x70 ---------------------------------- */
2064 [BTTV_BOARD_PC_HDTV] = {
2065 .name = "pcHDTV HD-2000 TV",
2066 .video_inputs = 4,
2067 /* .audio_inputs= 1, */
2068 .svhs = 2,
2069 .muxsel = MUXSEL(2, 3, 1, 0),
2070 .tuner_type = TUNER_PHILIPS_FCV1236D,
2071 .tuner_addr = ADDR_UNSET,
2072 .has_dvb = 1,
2073 },
2074 [BTTV_BOARD_TWINHAN_DST] = {
2075 .name = "Twinhan DST + clones",
2076 .no_msp34xx = 1,
2077 .no_tda7432 = 1,
2078 .tuner_type = TUNER_ABSENT,
2079 .tuner_addr = ADDR_UNSET,
2080 .no_video = 1,
2081 .has_dvb = 1,
2082 },
2083 [BTTV_BOARD_WINFASTVC100] = {
2084 .name = "Winfast VC100",
2085 .video_inputs = 3,
2086 /* .audio_inputs= 0, */
2087 .svhs = 1,
2088 /* Vid In, SVid In, Vid over SVid in connector */
2089 .muxsel = MUXSEL(3, 1, 1, 3),
2090 .no_msp34xx = 1,
2091 .no_tda7432 = 1,
2092 .tuner_type = TUNER_ABSENT,
2093 .tuner_addr = ADDR_UNSET,
2094 .pll = PLL_28,
2095 },
2096 [BTTV_BOARD_TEV560] = {
2097 .name = "Teppro TEV-560/InterVision IV-560",
2098 .video_inputs = 3,
2099 /* .audio_inputs= 1, */
2100 .svhs = 2,
2101 .gpiomask = 3,
2102 .muxsel = MUXSEL(2, 3, 1, 1),
2103 .gpiomux = { 1, 1, 1, 1 },
2104 .tuner_type = TUNER_PHILIPS_PAL,
2105 .tuner_addr = ADDR_UNSET,
2106 .pll = PLL_35,
2107 },
2108
2109 /* ---- card 0x74 ---------------------------------- */
2110 [BTTV_BOARD_SIMUS_GVC1100] = {
2111 .name = "SIMUS GVC1100",
2112 .video_inputs = 4,
2113 /* .audio_inputs= 0, */
2114 .svhs = NO_SVHS,
2115 .tuner_type = TUNER_ABSENT,
2116 .tuner_addr = ADDR_UNSET,
2117 .pll = PLL_28,
2118 .muxsel = MUXSEL(2, 2, 2, 2),
2119 .gpiomask = 0x3F,
2120 .muxsel_hook = gvc1100_muxsel,
2121 },
2122 [BTTV_BOARD_NGSTV_PLUS] = {
2123 /* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */
2124 .name = "NGS NGSTV+",
2125 .video_inputs = 3,
2126 .svhs = 2,
2127 .gpiomask = 0x008007,
2128 .muxsel = MUXSEL(2, 3, 0, 0),
2129 .gpiomux = { 0, 0, 0, 0 },
2130 .gpiomute = 0x000003,
2131 .pll = PLL_28,
2132 .tuner_type = TUNER_PHILIPS_PAL,
2133 .tuner_addr = ADDR_UNSET,
2134 .has_remote = 1,
2135 },
2136 [BTTV_BOARD_LMLBT4] = {
2137 /* http://linuxmedialabs.com */
2138 .name = "LMLBT4",
2139 .video_inputs = 4, /* IN1,IN2,IN3,IN4 */
2140 /* .audio_inputs= 0, */
2141 .svhs = NO_SVHS,
2142 .muxsel = MUXSEL(2, 3, 1, 0),
2143 .no_msp34xx = 1,
2144 .no_tda7432 = 1,
2145 .tuner_type = TUNER_ABSENT,
2146 .tuner_addr = ADDR_UNSET,
2147 },
2148 [BTTV_BOARD_TEKRAM_M205] = {
2149 /* Helmroos Harri <harri.helmroos@pp.inet.fi> */
2150 .name = "Tekram M205 PRO",
2151 .video_inputs = 3,
2152 /* .audio_inputs= 1, */
2153 .tuner_type = TUNER_PHILIPS_PAL,
2154 .tuner_addr = ADDR_UNSET,
2155 .svhs = 2,
2156 .gpiomask = 0x68,
2157 .muxsel = MUXSEL(2, 3, 1),
2158 .gpiomux = { 0x68, 0x68, 0x61, 0x61 },
2159 .pll = PLL_28,
2160 },
2161
2162 /* ---- card 0x78 ---------------------------------- */
2163 [BTTV_BOARD_CONTVFMI] = {
2164 /* Javier Cendan Ares <jcendan@lycos.es> */
2165 /* bt878 TV + FM without subsystem ID */
2166 .name = "Conceptronic CONTVFMi",
2167 .video_inputs = 3,
2168 /* .audio_inputs= 1, */
2169 .svhs = 2,
2170 .gpiomask = 0x008007,
2171 .muxsel = MUXSEL(2, 3, 1, 1),
2172 .gpiomux = { 0, 1, 2, 2 },
2173 .gpiomute = 3,
2174 .pll = PLL_28,
2175 .tuner_type = TUNER_PHILIPS_PAL,
2176 .tuner_addr = ADDR_UNSET,
2177 .has_remote = 1,
2178 .has_radio = 1,
2179 },
2180 [BTTV_BOARD_PICOLO_TETRA_CHIP] = {
2181 /*Eric DEBIEF <debief@telemsa.com>*/
2182 /*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controlled*/
2183 /* adds picolo_tetra_muxsel(), picolo_tetra_init(), the following declaration strucure, and #define BTTV_BOARD_PICOLO_TETRA_CHIP*/
2184 /*0x79 in bttv.h*/
2185 .name = "Euresys Picolo Tetra",
2186 .video_inputs = 4,
2187 /* .audio_inputs= 0, */
2188 .svhs = NO_SVHS,
2189 .gpiomask = 0,
2190 .gpiomask2 = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/
2191 .no_msp34xx = 1,
2192 .no_tda7432 = 1,
2193 /*878A input is always MUX0, see above.*/
2194 .muxsel = MUXSEL(2, 2, 2, 2),
2195 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2196 .pll = PLL_28,
2197 .muxsel_hook = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/
2198 .tuner_type = TUNER_ABSENT,
2199 .tuner_addr = ADDR_UNSET,
2200 },
2201 [BTTV_BOARD_SPIRIT_TV] = {
2202 /* Spirit TV Tuner from http://spiritmodems.com.au */
2203 /* Stafford Goodsell <surge@goliath.homeunix.org> */
2204 .name = "Spirit TV Tuner",
2205 .video_inputs = 3,
2206 /* .audio_inputs= 1, */
2207 .svhs = 2,
2208 .gpiomask = 0x0000000f,
2209 .muxsel = MUXSEL(2, 1, 1),
2210 .gpiomux = { 0x02, 0x00, 0x00, 0x00 },
2211 .tuner_type = TUNER_TEMIC_PAL,
2212 .tuner_addr = ADDR_UNSET,
2213 .no_msp34xx = 1,
2214 },
2215 [BTTV_BOARD_AVDVBT_771] = {
2216 /* Wolfram Joost <wojo@frokaschwei.de> */
2217 .name = "AVerMedia AVerTV DVB-T 771",
2218 .video_inputs = 2,
2219 .svhs = 1,
2220 .tuner_type = TUNER_ABSENT,
2221 .tuner_addr = ADDR_UNSET,
2222 .muxsel = MUXSEL(3, 3),
2223 .no_msp34xx = 1,
2224 .no_tda7432 = 1,
2225 .pll = PLL_28,
2226 .has_dvb = 1,
2227 .no_gpioirq = 1,
2228 .has_remote = 1,
2229 },
2230 /* ---- card 0x7c ---------------------------------- */
2231 [BTTV_BOARD_AVDVBT_761] = {
2232 /* Matt Jesson <dvb@jesson.eclipse.co.uk> */
2233 /* Based on the Nebula card data - added remote and new card number - BTTV_BOARD_AVDVBT_761, see also ir-kbd-gpio.c */
2234 .name = "AverMedia AverTV DVB-T 761",
2235 .video_inputs = 2,
2236 .svhs = 1,
2237 .muxsel = MUXSEL(3, 1, 2, 0), /* Comp0, S-Video, ?, ? */
2238 .no_msp34xx = 1,
2239 .no_tda7432 = 1,
2240 .pll = PLL_28,
2241 .tuner_type = TUNER_ABSENT,
2242 .tuner_addr = ADDR_UNSET,
2243 .has_dvb = 1,
2244 .no_gpioirq = 1,
2245 .has_remote = 1,
2246 },
2247 [BTTV_BOARD_MATRIX_VISIONSQ] = {
2248 /* andre.schwarz@matrix-vision.de */
2249 .name = "MATRIX Vision Sigma-SQ",
2250 .video_inputs = 16,
2251 /* .audio_inputs= 0, */
2252 .svhs = NO_SVHS,
2253 .gpiomask = 0x0,
2254 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3),
2255 .muxsel_hook = sigmaSQ_muxsel,
2256 .gpiomux = { 0 },
2257 .no_msp34xx = 1,
2258 .pll = PLL_28,
2259 .tuner_type = TUNER_ABSENT,
2260 .tuner_addr = ADDR_UNSET,
2261 },
2262 [BTTV_BOARD_MATRIX_VISIONSLC] = {
2263 /* andre.schwarz@matrix-vision.de */
2264 .name = "MATRIX Vision Sigma-SLC",
2265 .video_inputs = 4,
2266 /* .audio_inputs= 0, */
2267 .svhs = NO_SVHS,
2268 .gpiomask = 0x0,
2269 .muxsel = MUXSEL(2, 2, 2, 2),
2270 .muxsel_hook = sigmaSLC_muxsel,
2271 .gpiomux = { 0 },
2272 .no_msp34xx = 1,
2273 .pll = PLL_28,
2274 .tuner_type = TUNER_ABSENT,
2275 .tuner_addr = ADDR_UNSET,
2276 },
2277 /* BTTV_BOARD_APAC_VIEWCOMP */
2278 [BTTV_BOARD_APAC_VIEWCOMP] = {
2279 /* Attila Kondoros <attila.kondoros@chello.hu> */
2280 /* bt878 TV + FM 0x00000000 subsystem ID */
2281 .name = "APAC Viewcomp 878(AMAX)",
2282 .video_inputs = 2,
2283 /* .audio_inputs= 1, */
2284 .svhs = NO_SVHS,
2285 .gpiomask = 0xFF,
2286 .muxsel = MUXSEL(2, 3, 1, 1),
2287 .gpiomux = { 2, 0, 0, 0 },
2288 .gpiomute = 10,
2289 .pll = PLL_28,
2290 .tuner_type = TUNER_PHILIPS_PAL,
2291 .tuner_addr = ADDR_UNSET,
2292 .has_remote = 1, /* miniremote works, see ir-kbd-gpio.c */
2293 .has_radio = 1, /* not every card has radio */
2294 },
2295
2296 /* ---- card 0x80 ---------------------------------- */
2297 [BTTV_BOARD_DVICO_DVBT_LITE] = {
2298 /* Chris Pascoe <c.pascoe@itee.uq.edu.au> */
2299 .name = "DViCO FusionHDTV DVB-T Lite",
2300 .no_msp34xx = 1,
2301 .no_tda7432 = 1,
2302 .pll = PLL_28,
2303 .no_video = 1,
2304 .has_dvb = 1,
2305 .tuner_type = TUNER_ABSENT,
2306 .tuner_addr = ADDR_UNSET,
2307 },
2308 [BTTV_BOARD_VGEAR_MYVCD] = {
2309 /* Steven <photon38@pchome.com.tw> */
2310 .name = "V-Gear MyVCD",
2311 .video_inputs = 3,
2312 /* .audio_inputs= 1, */
2313 .svhs = 2,
2314 .gpiomask = 0x3f,
2315 .muxsel = MUXSEL(2, 3, 1, 0),
2316 .gpiomux = {0x31, 0x31, 0x31, 0x31 },
2317 .gpiomute = 0x31,
2318 .no_msp34xx = 1,
2319 .pll = PLL_28,
2320 .tuner_type = TUNER_PHILIPS_NTSC_M,
2321 .tuner_addr = ADDR_UNSET,
2322 .has_radio = 0,
2323 },
2324 [BTTV_BOARD_SUPER_TV] = {
2325 /* Rick C <cryptdragoon@gmail.com> */
2326 .name = "Super TV Tuner",
2327 .video_inputs = 4,
2328 /* .audio_inputs= 1, */
2329 .svhs = 2,
2330 .muxsel = MUXSEL(2, 3, 1, 0),
2331 .tuner_type = TUNER_PHILIPS_NTSC,
2332 .tuner_addr = ADDR_UNSET,
2333 .gpiomask = 0x008007,
2334 .gpiomux = { 0, 0x000001,0,0 },
2335 .has_radio = 1,
2336 },
2337 [BTTV_BOARD_TIBET_CS16] = {
2338 /* Chris Fanning <video4linux@haydon.net> */
2339 .name = "Tibet Systems 'Progress DVR' CS16",
2340 .video_inputs = 16,
2341 /* .audio_inputs= 0, */
2342 .svhs = NO_SVHS,
2343 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2344 .pll = PLL_28,
2345 .no_msp34xx = 1,
2346 .no_tda7432 = 1,
2347 .tuner_type = TUNER_ABSENT,
2348 .tuner_addr = ADDR_UNSET,
2349 .muxsel_hook = tibetCS16_muxsel,
2350 },
2351 [BTTV_BOARD_KODICOM_4400R] = {
2352 /* Bill Brack <wbrack@mmm.com.hk> */
2353 /*
2354 * Note that, because of the card's wiring, the "master"
2355 * BT878A chip (i.e. the one which controls the analog switch
2356 * and must use this card type) is the 2nd one detected. The
2357 * other 3 chips should use card type 0x85, whose description
2358 * follows this one. There is a EEPROM on the card (which is
2359 * connected to the I2C of one of those other chips), but is
2360 * not currently handled. There is also a facility for a
2361 * "monitor", which is also not currently implemented.
2362 */
2363 .name = "Kodicom 4400R (master)",
2364 .video_inputs = 16,
2365 /* .audio_inputs= 0, */
2366 .tuner_type = TUNER_ABSENT,
2367 .tuner_addr = ADDR_UNSET,
2368 .svhs = NO_SVHS,
2369 /* GPIO bits 0-9 used for analog switch:
2370 * 00 - 03: camera selector
2371 * 04 - 06: channel (controller) selector
2372 * 07: data (1->on, 0->off)
2373 * 08: strobe
2374 * 09: reset
2375 * bit 16 is input from sync separator for the channel
2376 */
2377 .gpiomask = 0x0003ff,
2378 .no_gpioirq = 1,
2379 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
2380 .pll = PLL_28,
2381 .no_msp34xx = 1,
2382 .no_tda7432 = 1,
2383 .muxsel_hook = kodicom4400r_muxsel,
2384 },
2385 [BTTV_BOARD_KODICOM_4400R_SL] = {
2386 /* Bill Brack <wbrack@mmm.com.hk> */
2387 /* Note that, for reasons unknown, the "master" BT878A chip (i.e. the
2388 * one which controls the analog switch, and must use the card type)
2389 * is the 2nd one detected. The other 3 chips should use this card
2390 * type
2391 */
2392 .name = "Kodicom 4400R (slave)",
2393 .video_inputs = 16,
2394 /* .audio_inputs= 0, */
2395 .tuner_type = TUNER_ABSENT,
2396 .tuner_addr = ADDR_UNSET,
2397 .svhs = NO_SVHS,
2398 .gpiomask = 0x010000,
2399 .no_gpioirq = 1,
2400 .muxsel = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
2401 .pll = PLL_28,
2402 .no_msp34xx = 1,
2403 .no_tda7432 = 1,
2404 .muxsel_hook = kodicom4400r_muxsel,
2405 },
2406 /* ---- card 0x86---------------------------------- */
2407 [BTTV_BOARD_ADLINK_RTV24] = {
2408 /* Michael Henson <mhenson@clarityvi.com> */
2409 /* Adlink RTV24 with special unlock codes */
2410 .name = "Adlink RTV24",
2411 .video_inputs = 4,
2412 /* .audio_inputs= 1, */
2413 .svhs = 2,
2414 .muxsel = MUXSEL(2, 3, 1, 0),
2415 .tuner_type = UNSET,
2416 .tuner_addr = ADDR_UNSET,
2417 .pll = PLL_28,
2418 },
2419 /* ---- card 0x87---------------------------------- */
2420 [BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE] = {
2421 /* Michael Krufky <mkrufky@linuxtv.org> */
2422 .name = "DViCO FusionHDTV 5 Lite",
2423 .tuner_type = TUNER_LG_TDVS_H06XF, /* TDVS-H064F */
2424 .tuner_addr = ADDR_UNSET,
2425 .video_inputs = 3,
2426 /* .audio_inputs= 1, */
2427 .svhs = 2,
2428 .muxsel = MUXSEL(2, 3, 1),
2429 .gpiomask = 0x00e00007,
2430 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2431 .gpiomute = 0x00c00007,
2432 .no_msp34xx = 1,
2433 .no_tda7432 = 1,
2434 .has_dvb = 1,
2435 },
2436 /* ---- card 0x88---------------------------------- */
2437 [BTTV_BOARD_ACORP_Y878F] = {
2438 /* Mauro Carvalho Chehab <mchehab@kernel.org> */
2439 .name = "Acorp Y878F",
2440 .video_inputs = 3,
2441 /* .audio_inputs= 1, */
2442 .svhs = 2,
2443 .gpiomask = 0x01fe00,
2444 .muxsel = MUXSEL(2, 3, 1, 1),
2445 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
2446 .gpiomute = 0x002000,
2447 .pll = PLL_28,
2448 .tuner_type = TUNER_YMEC_TVF66T5_B_DFF,
2449 .tuner_addr = 0xc1 >>1,
2450 .has_radio = 1,
2451 },
2452 /* ---- card 0x89 ---------------------------------- */
2453 [BTTV_BOARD_CONCEPTRONIC_CTVFMI2] = {
2454 .name = "Conceptronic CTVFMi v2",
2455 .video_inputs = 3,
2456 /* .audio_inputs= 1, */
2457 .svhs = 2,
2458 .gpiomask = 0x001c0007,
2459 .muxsel = MUXSEL(2, 3, 1, 1),
2460 .gpiomux = { 0, 1, 2, 2 },
2461 .gpiomute = 3,
2462 .pll = PLL_28,
2463 .tuner_type = TUNER_TENA_9533_DI,
2464 .tuner_addr = ADDR_UNSET,
2465 .has_remote = 1,
2466 .has_radio = 1,
2467 },
2468 /* ---- card 0x8a ---------------------------------- */
2469 [BTTV_BOARD_PV_BT878P_2E] = {
2470 .name = "Prolink Pixelview PV-BT878P+ (Rev.2E)",
2471 .video_inputs = 5,
2472 /* .audio_inputs= 1, */
2473 .svhs = 3,
2474 .has_dig_in = 1,
2475 .gpiomask = 0x01fe00,
2476 .muxsel = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */
2477 /* .digital_mode= DIGITAL_MODE_CAMERA, */
2478 .gpiomux = { 0x00400, 0x10400, 0x04400, 0x80000 },
2479 .gpiomute = 0x12400,
2480 .no_msp34xx = 1,
2481 .pll = PLL_28,
2482 .tuner_type = TUNER_LG_PAL_FM,
2483 .tuner_addr = ADDR_UNSET,
2484 .has_remote = 1,
2485 },
2486 /* ---- card 0x8b ---------------------------------- */
2487 [BTTV_BOARD_PV_M4900] = {
2488 /* Sérgio Fortier <sergiofortier@yahoo.com.br> */
2489 .name = "Prolink PixelView PlayTV MPEG2 PV-M4900",
2490 .video_inputs = 3,
2491 /* .audio_inputs= 1, */
2492 .svhs = 2,
2493 .gpiomask = 0x3f,
2494 .muxsel = MUXSEL(2, 3, 1, 1),
2495 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
2496 .gpiomute = 0x29,
2497 .no_msp34xx = 1,
2498 .pll = PLL_28,
2499 .tuner_type = TUNER_YMEC_TVF_5533MF,
2500 .tuner_addr = ADDR_UNSET,
2501 .has_radio = 1,
2502 .has_remote = 1,
2503 },
2504 /* ---- card 0x8c ---------------------------------- */
2505 /* Has four Bt878 chips behind a PCI bridge, each chip has:
2506 one external BNC composite input (mux 2)
2507 three internal composite inputs (unknown muxes)
2508 an 18-bit stereo A/D (CS5331A), which has:
2509 one external stereo unblanced (RCA) audio connection
2510 one (or 3?) internal stereo balanced (XLR) audio connection
2511 input is selected via gpio to a 14052B mux
2512 (mask=0x300, unbal=0x000, bal=0x100, ??=0x200,0x300)
2513 gain is controlled via an X9221A chip on the I2C bus @0x28
2514 sample rate is controlled via gpio to an MK1413S
2515 (mask=0x3, 32kHz=0x0, 44.1kHz=0x1, 48kHz=0x2, ??=0x3)
2516 There is neither a tuner nor an svideo input. */
2517 [BTTV_BOARD_OSPREY440] = {
2518 .name = "Osprey 440",
2519 .video_inputs = 4,
2520 /* .audio_inputs= 2, */
2521 .svhs = NO_SVHS,
2522 .muxsel = MUXSEL(2, 3, 0, 1), /* 3,0,1 are guesses */
2523 .gpiomask = 0x303,
2524 .gpiomute = 0x000, /* int + 32kHz */
2525 .gpiomux = { 0, 0, 0x000, 0x100},
2526 .pll = PLL_28,
2527 .tuner_type = TUNER_ABSENT,
2528 .tuner_addr = ADDR_UNSET,
2529 .no_msp34xx = 1,
2530 .no_tda7432 = 1,
2531 },
2532 /* ---- card 0x8d ---------------------------------- */
2533 [BTTV_BOARD_ASOUND_SKYEYE] = {
2534 .name = "Asound Skyeye PCTV",
2535 .video_inputs = 3,
2536 /* .audio_inputs= 1, */
2537 .svhs = 2,
2538 .gpiomask = 15,
2539 .muxsel = MUXSEL(2, 3, 1, 1),
2540 .gpiomux = { 2, 0, 0, 0 },
2541 .gpiomute = 1,
2542 .pll = PLL_28,
2543 .tuner_type = TUNER_PHILIPS_NTSC,
2544 .tuner_addr = ADDR_UNSET,
2545 },
2546 /* ---- card 0x8e ---------------------------------- */
2547 [BTTV_BOARD_SABRENT_TVFM] = {
2548 .name = "Sabrent TV-FM (bttv version)",
2549 .video_inputs = 3,
2550 /* .audio_inputs= 1, */
2551 .svhs = 2,
2552 .gpiomask = 0x108007,
2553 .muxsel = MUXSEL(2, 3, 1, 1),
2554 .gpiomux = { 100000, 100002, 100002, 100000 },
2555 .no_msp34xx = 1,
2556 .no_tda7432 = 1,
2557 .pll = PLL_28,
2558 .tuner_type = TUNER_TNF_5335MF,
2559 .tuner_addr = ADDR_UNSET,
2560 .has_radio = 1,
2561 },
2562 /* ---- card 0x8f ---------------------------------- */
2563 [BTTV_BOARD_HAUPPAUGE_IMPACTVCB] = {
2564 .name = "Hauppauge ImpactVCB (bt878)",
2565 .video_inputs = 4,
2566 /* .audio_inputs= 0, */
2567 .svhs = NO_SVHS,
2568 .gpiomask = 0x0f, /* old: 7 */
2569 .muxsel = MUXSEL(0, 1, 3, 2), /* Composite 0-3 */
2570 .no_msp34xx = 1,
2571 .no_tda7432 = 1,
2572 .tuner_type = TUNER_ABSENT,
2573 .tuner_addr = ADDR_UNSET,
2574 },
2575 [BTTV_BOARD_MACHTV_MAGICTV] = {
2576 /* Julian Calaby <julian.calaby@gmail.com>
2577 * Slightly different from original MachTV definition (0x60)
2578
2579 * FIXME: RegSpy says gpiomask should be "0x001c800f", but it
2580 * stuffs up remote chip. Bug is a pin on the jaecs is not set
2581 * properly (methinks) causing no keyup bits being set */
2582
2583 .name = "MagicTV", /* rebranded MachTV */
2584 .video_inputs = 3,
2585 /* .audio_inputs= 1, */
2586 .svhs = 2,
2587 .gpiomask = 7,
2588 .muxsel = MUXSEL(2, 3, 1, 1),
2589 .gpiomux = { 0, 1, 2, 3 },
2590 .gpiomute = 4,
2591 .tuner_type = TUNER_TEMIC_4009FR5_PAL,
2592 .tuner_addr = ADDR_UNSET,
2593 .pll = PLL_28,
2594 .has_radio = 1,
2595 .has_remote = 1,
2596 },
2597 [BTTV_BOARD_SSAI_SECURITY] = {
2598 .name = "SSAI Security Video Interface",
2599 .video_inputs = 4,
2600 /* .audio_inputs= 0, */
2601 .svhs = NO_SVHS,
2602 .muxsel = MUXSEL(0, 1, 2, 3),
2603 .tuner_type = TUNER_ABSENT,
2604 .tuner_addr = ADDR_UNSET,
2605 },
2606 [BTTV_BOARD_SSAI_ULTRASOUND] = {
2607 .name = "SSAI Ultrasound Video Interface",
2608 .video_inputs = 2,
2609 /* .audio_inputs= 0, */
2610 .svhs = 1,
2611 .muxsel = MUXSEL(2, 0, 1, 3),
2612 .tuner_type = TUNER_ABSENT,
2613 .tuner_addr = ADDR_UNSET,
2614 },
2615 /* ---- card 0x94---------------------------------- */
2616 [BTTV_BOARD_DVICO_FUSIONHDTV_2] = {
2617 .name = "DViCO FusionHDTV 2",
2618 .tuner_type = TUNER_PHILIPS_FCV1236D,
2619 .tuner_addr = ADDR_UNSET,
2620 .video_inputs = 3,
2621 /* .audio_inputs= 1, */
2622 .svhs = 2,
2623 .muxsel = MUXSEL(2, 3, 1),
2624 .gpiomask = 0x00e00007,
2625 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2626 .gpiomute = 0x00c00007,
2627 .no_msp34xx = 1,
2628 .no_tda7432 = 1,
2629 },
2630 /* ---- card 0x95---------------------------------- */
2631 [BTTV_BOARD_TYPHOON_TVTUNERPCI] = {
2632 .name = "Typhoon TV-Tuner PCI (50684)",
2633 .video_inputs = 3,
2634 /* .audio_inputs= 1, */
2635 .svhs = 2,
2636 .gpiomask = 0x3014f,
2637 .muxsel = MUXSEL(2, 3, 1, 1),
2638 .gpiomux = { 0x20001,0x10001, 0, 0 },
2639 .gpiomute = 10,
2640 .pll = PLL_28,
2641 .tuner_type = TUNER_PHILIPS_PAL_I,
2642 .tuner_addr = ADDR_UNSET,
2643 },
2644 [BTTV_BOARD_GEOVISION_GV600] = {
2645 /* emhn@usb.ve */
2646 .name = "Geovision GV-600",
2647 .video_inputs = 16,
2648 /* .audio_inputs= 0, */
2649 .svhs = NO_SVHS,
2650 .gpiomask = 0x0,
2651 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2652 .muxsel_hook = geovision_muxsel,
2653 .gpiomux = { 0 },
2654 .no_msp34xx = 1,
2655 .pll = PLL_28,
2656 .tuner_type = TUNER_ABSENT,
2657 .tuner_addr = ADDR_UNSET,
2658 },
2659 [BTTV_BOARD_KOZUMI_KTV_01C] = {
2660 /* Mauro Lacy <mauro@lacy.com.ar>
2661 * Based on MagicTV and Conceptronic CONTVFMi */
2662
2663 .name = "Kozumi KTV-01C",
2664 .video_inputs = 3,
2665 /* .audio_inputs= 1, */
2666 .svhs = 2,
2667 .gpiomask = 0x008007,
2668 .muxsel = MUXSEL(2, 3, 1, 1),
2669 .gpiomux = { 0, 1, 2, 2 }, /* CONTVFMi */
2670 .gpiomute = 3, /* CONTVFMi */
2671 .tuner_type = TUNER_PHILIPS_FM1216ME_MK3, /* TCL MK3 */
2672 .tuner_addr = ADDR_UNSET,
2673 .pll = PLL_28,
2674 .has_radio = 1,
2675 .has_remote = 1,
2676 },
2677 [BTTV_BOARD_ENLTV_FM_2] = {
2678 /* Encore TV Tuner Pro ENL TV-FM-2
2679 Mauro Carvalho Chehab <mchehab@kernel.org> */
2680 .name = "Encore ENL TV-FM-2",
2681 .video_inputs = 3,
2682 /* .audio_inputs= 1, */
2683 .svhs = 2,
2684 /* bit 6 -> IR disabled
2685 bit 18/17 = 00 -> mute
2686 01 -> enable external audio input
2687 10 -> internal audio input (mono?)
2688 11 -> internal audio input
2689 */
2690 .gpiomask = 0x060040,
2691 .muxsel = MUXSEL(2, 3, 3),
2692 .gpiomux = { 0x60000, 0x60000, 0x20000, 0x20000 },
2693 .gpiomute = 0,
2694 .tuner_type = TUNER_TCL_MF02GIP_5N,
2695 .tuner_addr = ADDR_UNSET,
2696 .pll = PLL_28,
2697 .has_radio = 1,
2698 .has_remote = 1,
2699 },
2700 [BTTV_BOARD_VD012] = {
2701 /* D.Heer@Phytec.de */
2702 .name = "PHYTEC VD-012 (bt878)",
2703 .video_inputs = 4,
2704 /* .audio_inputs= 0, */
2705 .svhs = NO_SVHS,
2706 .gpiomask = 0x00,
2707 .muxsel = MUXSEL(0, 2, 3, 1),
2708 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2709 .pll = PLL_28,
2710 .tuner_type = TUNER_ABSENT,
2711 .tuner_addr = ADDR_UNSET,
2712 },
2713 [BTTV_BOARD_VD012_X1] = {
2714 /* D.Heer@Phytec.de */
2715 .name = "PHYTEC VD-012-X1 (bt878)",
2716 .video_inputs = 4,
2717 /* .audio_inputs= 0, */
2718 .svhs = 3,
2719 .gpiomask = 0x00,
2720 .muxsel = MUXSEL(2, 3, 1),
2721 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2722 .pll = PLL_28,
2723 .tuner_type = TUNER_ABSENT,
2724 .tuner_addr = ADDR_UNSET,
2725 },
2726 [BTTV_BOARD_VD012_X2] = {
2727 /* D.Heer@Phytec.de */
2728 .name = "PHYTEC VD-012-X2 (bt878)",
2729 .video_inputs = 4,
2730 /* .audio_inputs= 0, */
2731 .svhs = 3,
2732 .gpiomask = 0x00,
2733 .muxsel = MUXSEL(3, 2, 1),
2734 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2735 .pll = PLL_28,
2736 .tuner_type = TUNER_ABSENT,
2737 .tuner_addr = ADDR_UNSET,
2738 },
2739 [BTTV_BOARD_GEOVISION_GV800S] = {
2740 /* Bruno Christo <bchristo@inf.ufsm.br>
2741 *
2742 * GeoVision GV-800(S) has 4 Conexant Fusion 878A:
2743 * 1 audio input per BT878A = 4 audio inputs
2744 * 4 video inputs per BT878A = 16 video inputs
2745 * This is the first BT878A chip of the GV-800(S). It's the
2746 * "master" chip and it controls the video inputs through an
2747 * analog multiplexer (a CD22M3494) via some GPIO pins. The
2748 * slaves should use card type 0x9e (following this one).
2749 * There is a EEPROM on the card which is currently not handled.
2750 * The audio input is not working yet.
2751 */
2752 .name = "Geovision GV-800(S) (master)",
2753 .video_inputs = 4,
2754 /* .audio_inputs= 1, */
2755 .tuner_type = TUNER_ABSENT,
2756 .tuner_addr = ADDR_UNSET,
2757 .svhs = NO_SVHS,
2758 .gpiomask = 0xf107f,
2759 .no_gpioirq = 1,
2760 .muxsel = MUXSEL(2, 2, 2, 2),
2761 .pll = PLL_28,
2762 .no_msp34xx = 1,
2763 .no_tda7432 = 1,
2764 .muxsel_hook = gv800s_muxsel,
2765 },
2766 [BTTV_BOARD_GEOVISION_GV800S_SL] = {
2767 /* Bruno Christo <bchristo@inf.ufsm.br>
2768 *
2769 * GeoVision GV-800(S) has 4 Conexant Fusion 878A:
2770 * 1 audio input per BT878A = 4 audio inputs
2771 * 4 video inputs per BT878A = 16 video inputs
2772 * The 3 other BT878A chips are "slave" chips of the GV-800(S)
2773 * and should use this card type.
2774 * The audio input is not working yet.
2775 */
2776 .name = "Geovision GV-800(S) (slave)",
2777 .video_inputs = 4,
2778 /* .audio_inputs= 1, */
2779 .tuner_type = TUNER_ABSENT,
2780 .tuner_addr = ADDR_UNSET,
2781 .svhs = NO_SVHS,
2782 .gpiomask = 0x00,
2783 .no_gpioirq = 1,
2784 .muxsel = MUXSEL(2, 2, 2, 2),
2785 .pll = PLL_28,
2786 .no_msp34xx = 1,
2787 .no_tda7432 = 1,
2788 .muxsel_hook = gv800s_muxsel,
2789 },
2790 [BTTV_BOARD_PV183] = {
2791 .name = "ProVideo PV183", /* 0x9f */
2792 .video_inputs = 2,
2793 /* .audio_inputs= 0, */
2794 .svhs = NO_SVHS,
2795 .gpiomask = 0,
2796 .muxsel = MUXSEL(2, 3),
2797 .gpiomux = { 0 },
2798 .no_msp34xx = 1,
2799 .pll = PLL_28,
2800 .tuner_type = TUNER_ABSENT,
2801 .tuner_addr = ADDR_UNSET,
2802 },
2803 /* ---- card 0xa0---------------------------------- */
2804 [BTTV_BOARD_TVT_TD3116] = {
2805 .name = "Tongwei Video Technology TD-3116",
2806 .video_inputs = 16,
2807 .gpiomask = 0xc00ff,
2808 .muxsel = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2809 .muxsel_hook = td3116_muxsel,
2810 .svhs = NO_SVHS,
2811 .pll = PLL_28,
2812 .tuner_type = TUNER_ABSENT,
2813 },
2814 [BTTV_BOARD_APOSONIC_WDVR] = {
2815 .name = "Aposonic W-DVR",
2816 .video_inputs = 4,
2817 .svhs = NO_SVHS,
2818 .muxsel = MUXSEL(2, 3, 1, 0),
2819 .tuner_type = TUNER_ABSENT,
2820 },
2821 [BTTV_BOARD_ADLINK_MPG24] = {
2822 /* Adlink MPG24 */
2823 .name = "Adlink MPG24",
2824 .video_inputs = 1,
2825 /* .audio_inputs= 1, */
2826 .svhs = NO_SVHS,
2827 .muxsel = MUXSEL(2, 2, 2, 2),
2828 .tuner_type = UNSET,
2829 .tuner_addr = ADDR_UNSET,
2830 .pll = PLL_28,
2831 },
2832 [BTTV_BOARD_BT848_CAP_14] = {
2833 .name = "Bt848 Capture 14MHz",
2834 .video_inputs = 4,
2835 .svhs = 2,
2836 .muxsel = MUXSEL(2, 3, 1, 0),
2837 .pll = PLL_14,
2838 .tuner_type = TUNER_ABSENT,
2839 },
2840 [BTTV_BOARD_CYBERVISION_CV06] = {
2841 .name = "CyberVision CV06 (SV)",
2842 .video_inputs = 4,
2843 /* .audio_inputs= 0, */
2844 .svhs = NO_SVHS,
2845 .muxsel = MUXSEL(2, 3, 1, 0),
2846 .pll = PLL_28,
2847 .tuner_type = TUNER_ABSENT,
2848 .tuner_addr = ADDR_UNSET,
2849 },
2850 [BTTV_BOARD_KWORLD_VSTREAM_XPERT] = {
2851 /* Pojar George <geoubuntu@gmail.com> */
2852 .name = "Kworld V-Stream Xpert TV PVR878",
2853 .video_inputs = 3,
2854 /* .audio_inputs= 1, */
2855 .svhs = 2,
2856 .gpiomask = 0x001c0007,
2857 .muxsel = MUXSEL(2, 3, 1, 1),
2858 .gpiomux = { 0, 1, 2, 2 },
2859 .gpiomute = 3,
2860 .pll = PLL_28,
2861 .tuner_type = TUNER_TENA_9533_DI,
2862 .tuner_addr = ADDR_UNSET,
2863 .has_remote = 1,
2864 .has_radio = 1,
2865 },
2866 /* ---- card 0xa6---------------------------------- */
2867 [BTTV_BOARD_PCI_8604PW] = {
2868 /* PCI-8604PW with special unlock sequence */
2869 .name = "PCI-8604PW",
2870 .video_inputs = 2,
2871 /* .audio_inputs= 0, */
2872 .svhs = NO_SVHS,
2873 /* The second input is available on CN4, if populated.
2874 * The other 5x2 header (CN2?) connects to the same inputs
2875 * as the on-board BNCs */
2876 .muxsel = MUXSEL(2, 3),
2877 .tuner_type = TUNER_ABSENT,
2878 .no_msp34xx = 1,
2879 .no_tda7432 = 1,
2880 .pll = PLL_35,
2881 },
2882 };
2883
2884 static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards);
2885
2886 /* ----------------------------------------------------------------------- */
2887
2888 static unsigned char eeprom_data[256];
2889
2890 /*
2891 * identify card
2892 */
bttv_idcard(struct bttv * btv)2893 void bttv_idcard(struct bttv *btv)
2894 {
2895 unsigned int gpiobits;
2896 int i,type;
2897
2898 /* read PCI subsystem ID */
2899 btv->cardid = btv->c.pci->subsystem_device << 16;
2900 btv->cardid |= btv->c.pci->subsystem_vendor;
2901
2902 if (0 != btv->cardid && 0xffffffff != btv->cardid) {
2903 /* look for the card */
2904 for (type = -1, i = 0; cards[i].id != 0; i++)
2905 if (cards[i].id == btv->cardid)
2906 type = i;
2907
2908 if (type != -1) {
2909 /* found it */
2910 pr_info("%d: detected: %s [card=%d], PCI subsystem ID is %04x:%04x\n",
2911 btv->c.nr, cards[type].name, cards[type].cardnr,
2912 btv->cardid & 0xffff,
2913 (btv->cardid >> 16) & 0xffff);
2914 btv->c.type = cards[type].cardnr;
2915 } else {
2916 /* 404 */
2917 pr_info("%d: subsystem: %04x:%04x (UNKNOWN)\n",
2918 btv->c.nr, btv->cardid & 0xffff,
2919 (btv->cardid >> 16) & 0xffff);
2920 pr_debug("please mail id, board name and the correct card= insmod option to linux-media@vger.kernel.org\n");
2921 }
2922 }
2923
2924 /* let the user override the autodetected type */
2925 if (card[btv->c.nr] < bttv_num_tvcards)
2926 btv->c.type=card[btv->c.nr];
2927
2928 /* print which card config we are using */
2929 pr_info("%d: using: %s [card=%d,%s]\n",
2930 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type,
2931 card[btv->c.nr] < bttv_num_tvcards
2932 ? "insmod option" : "autodetected");
2933
2934 /* overwrite gpio stuff ?? */
2935 if (UNSET == audioall && UNSET == audiomux[0])
2936 return;
2937
2938 if (UNSET != audiomux[0]) {
2939 gpiobits = 0;
2940 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2941 bttv_tvcards[btv->c.type].gpiomux[i] = audiomux[i];
2942 gpiobits |= audiomux[i];
2943 }
2944 } else {
2945 gpiobits = audioall;
2946 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2947 bttv_tvcards[btv->c.type].gpiomux[i] = audioall;
2948 }
2949 }
2950 bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits;
2951 pr_info("%d: gpio config override: mask=0x%x, mux=",
2952 btv->c.nr, bttv_tvcards[btv->c.type].gpiomask);
2953 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2954 pr_cont("%s0x%x",
2955 i ? "," : "", bttv_tvcards[btv->c.type].gpiomux[i]);
2956 }
2957 pr_cont("\n");
2958 }
2959
2960 /*
2961 * (most) board specific initialisations goes here
2962 */
2963
2964 /* Some Modular Technology cards have an eeprom, but no subsystem ID */
identify_by_eeprom(struct bttv * btv,unsigned char eeprom_data[256])2965 static void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256])
2966 {
2967 int type = -1;
2968
2969 if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13))
2970 type = BTTV_BOARD_MODTEC_205;
2971 else if (0 == strncmp(eeprom_data+20,"Picolo",7))
2972 type = BTTV_BOARD_EURESYS_PICOLO;
2973 else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0)
2974 type = BTTV_BOARD_HAUPPAUGE; /* old bt848 */
2975
2976 if (-1 != type) {
2977 btv->c.type = type;
2978 pr_info("%d: detected by eeprom: %s [card=%d]\n",
2979 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type);
2980 }
2981 }
2982
flyvideo_gpio(struct bttv * btv)2983 static void flyvideo_gpio(struct bttv *btv)
2984 {
2985 int gpio, has_remote, has_radio, is_capture_only;
2986 int is_lr90, has_tda9820_tda9821;
2987 int tuner_type = UNSET, ttype;
2988
2989 gpio_inout(0xffffff, 0);
2990 udelay(8); /* without this we would see the 0x1800 mask */
2991 gpio = gpio_read();
2992 /* FIXME: must restore OUR_EN ??? */
2993
2994 /* all cards provide GPIO info, some have an additional eeprom
2995 * LR50: GPIO coding can be found lower right CP1 .. CP9
2996 * CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1.
2997 * GPIO14-12: n.c.
2998 * LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878)
2999
3000 * lowest 3 bytes are remote control codes (no handshake needed)
3001 * xxxFFF: No remote control chip soldered
3002 * xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered
3003 * Note: Some bits are Audio_Mask !
3004 */
3005 ttype = (gpio & 0x0f0000) >> 16;
3006 switch (ttype) {
3007 case 0x0:
3008 tuner_type = 2; /* NTSC, e.g. TPI8NSR11P */
3009 break;
3010 case 0x2:
3011 tuner_type = 39; /* LG NTSC (newer TAPC series) TAPC-H701P */
3012 break;
3013 case 0x4:
3014 tuner_type = 5; /* Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216 */
3015 break;
3016 case 0x6:
3017 tuner_type = 37; /* LG PAL (newer TAPC series) TAPC-G702P */
3018 break;
3019 case 0xC:
3020 tuner_type = 3; /* Philips SECAM(+PAL) FQ1216ME or FI1216MF */
3021 break;
3022 default:
3023 pr_info("%d: FlyVideo_gpio: unknown tuner type\n", btv->c.nr);
3024 break;
3025 }
3026
3027 has_remote = gpio & 0x800000;
3028 has_radio = gpio & 0x400000;
3029 /* unknown 0x200000;
3030 * unknown2 0x100000; */
3031 is_capture_only = !(gpio & 0x008000); /* GPIO15 */
3032 has_tda9820_tda9821 = !(gpio & 0x004000);
3033 is_lr90 = !(gpio & 0x002000); /* else LR26/LR50 (LR38/LR51 f. capture only) */
3034 /*
3035 * gpio & 0x001000 output bit for audio routing */
3036
3037 if (is_capture_only)
3038 tuner_type = TUNER_ABSENT; /* No tuner present */
3039
3040 pr_info("%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n",
3041 btv->c.nr, has_radio ? "yes" : "no",
3042 has_remote ? "yes" : "no", tuner_type, gpio);
3043 pr_info("%d: FlyVideo LR90=%s tda9821/tda9820=%s capture_only=%s\n",
3044 btv->c.nr, is_lr90 ? "yes" : "no",
3045 has_tda9820_tda9821 ? "yes" : "no",
3046 is_capture_only ? "yes" : "no");
3047
3048 if (tuner_type != UNSET) /* only set if known tuner autodetected, else let insmod option through */
3049 btv->tuner_type = tuner_type;
3050 btv->has_radio = has_radio;
3051
3052 /* LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80
3053 * LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00
3054 * Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute */
3055 if (has_tda9820_tda9821)
3056 btv->audio_mode_gpio = lt9415_audio;
3057 /* todo: if(has_tda9874) btv->audio_mode_gpio = fv2000s_audio; */
3058 }
3059
3060 static int miro_tunermap[] = { 0,6,2,3, 4,5,6,0, 3,0,4,5, 5,2,16,1,
3061 14,2,17,1, 4,1,4,3, 1,2,16,1, 4,4,4,4 };
3062 static int miro_fmtuner[] = { 0,0,0,0, 0,0,0,0, 0,0,0,0, 0,0,0,1,
3063 1,1,1,1, 1,1,1,0, 0,0,0,0, 0,1,0,0 };
3064
miro_pinnacle_gpio(struct bttv * btv)3065 static void miro_pinnacle_gpio(struct bttv *btv)
3066 {
3067 int id,msp,gpio;
3068 char *info;
3069
3070 gpio_inout(0xffffff, 0);
3071 gpio = gpio_read();
3072 id = ((gpio>>10) & 63) -1;
3073 msp = bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx");
3074 if (id < 32) {
3075 btv->tuner_type = miro_tunermap[id];
3076 if (0 == (gpio & 0x20)) {
3077 btv->has_radio = 1;
3078 if (!miro_fmtuner[id]) {
3079 btv->has_tea575x = 1;
3080 btv->tea_gpio.wren = 6;
3081 btv->tea_gpio.most = 7;
3082 btv->tea_gpio.clk = 8;
3083 btv->tea_gpio.data = 9;
3084 tea575x_init(btv);
3085 }
3086 } else {
3087 btv->has_radio = 0;
3088 }
3089 if (-1 != msp) {
3090 if (btv->c.type == BTTV_BOARD_MIRO)
3091 btv->c.type = BTTV_BOARD_MIROPRO;
3092 if (btv->c.type == BTTV_BOARD_PINNACLE)
3093 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3094 }
3095 pr_info("%d: miro: id=%d tuner=%d radio=%s stereo=%s\n",
3096 btv->c.nr, id+1, btv->tuner_type,
3097 !btv->has_radio ? "no" :
3098 (btv->has_tea575x ? "tea575x" : "fmtuner"),
3099 (-1 == msp) ? "no" : "yes");
3100 } else {
3101 /* new cards with microtune tuner */
3102 id = 63 - id;
3103 btv->has_radio = 0;
3104 switch (id) {
3105 case 1:
3106 info = "PAL / mono";
3107 btv->tda9887_conf = TDA9887_INTERCARRIER;
3108 break;
3109 case 2:
3110 info = "PAL+SECAM / stereo";
3111 btv->has_radio = 1;
3112 btv->tda9887_conf = TDA9887_QSS;
3113 break;
3114 case 3:
3115 info = "NTSC / stereo";
3116 btv->has_radio = 1;
3117 btv->tda9887_conf = TDA9887_QSS;
3118 break;
3119 case 4:
3120 info = "PAL+SECAM / mono";
3121 btv->tda9887_conf = TDA9887_QSS;
3122 break;
3123 case 5:
3124 info = "NTSC / mono";
3125 btv->tda9887_conf = TDA9887_INTERCARRIER;
3126 break;
3127 case 6:
3128 info = "NTSC / stereo";
3129 btv->tda9887_conf = TDA9887_INTERCARRIER;
3130 break;
3131 case 7:
3132 info = "PAL / stereo";
3133 btv->tda9887_conf = TDA9887_INTERCARRIER;
3134 break;
3135 default:
3136 info = "oops: unknown card";
3137 break;
3138 }
3139 if (-1 != msp)
3140 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3141 pr_info("%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n",
3142 btv->c.nr, id, info, btv->has_radio ? "yes" : "no");
3143 btv->tuner_type = TUNER_MT2032;
3144 }
3145 }
3146
3147 /* GPIO21 L: Buffer aktiv, H: Buffer inaktiv */
3148 #define LM1882_SYNC_DRIVE 0x200000L
3149
init_ids_eagle(struct bttv * btv)3150 static void init_ids_eagle(struct bttv *btv)
3151 {
3152 gpio_inout(0xffffff,0xFFFF37);
3153 gpio_write(0x200020);
3154
3155 /* flash strobe inverter ?! */
3156 gpio_write(0x200024);
3157
3158 /* switch sync drive off */
3159 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3160
3161 /* set BT848 muxel to 2 */
3162 btaor((2)<<5, ~(2<<5), BT848_IFORM);
3163 }
3164
3165 /* Muxsel helper for the IDS Eagle.
3166 * the eagles does not use the standard muxsel-bits but
3167 * has its own multiplexer */
eagle_muxsel(struct bttv * btv,unsigned int input)3168 static void eagle_muxsel(struct bttv *btv, unsigned int input)
3169 {
3170 gpio_bits(3, input & 3);
3171
3172 /* composite */
3173 /* set chroma ADC to sleep */
3174 btor(BT848_ADC_C_SLEEP, BT848_ADC);
3175 /* set to composite video */
3176 btand(~BT848_CONTROL_COMP, BT848_E_CONTROL);
3177 btand(~BT848_CONTROL_COMP, BT848_O_CONTROL);
3178
3179 /* switch sync drive off */
3180 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3181 }
3182
gvc1100_muxsel(struct bttv * btv,unsigned int input)3183 static void gvc1100_muxsel(struct bttv *btv, unsigned int input)
3184 {
3185 static const int masks[] = {0x30, 0x01, 0x12, 0x23};
3186 gpio_write(masks[input%4]);
3187 }
3188
3189 /* LMLBT4x initialization - to allow access to GPIO bits for sensors input and
3190 alarms output
3191
3192 GPIObit | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
3193 assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1| | |
3194
3195 IN - sensor inputs, INx - sensor inputs and TI XORed together
3196 O1,O2,O3 - alarm outputs (relays)
3197
3198 OUT ENABLE 1 1 0 . 1 1 0 0 . 0 0 0 0 = 0x6C0
3199
3200 */
3201
init_lmlbt4x(struct bttv * btv)3202 static void init_lmlbt4x(struct bttv *btv)
3203 {
3204 pr_debug("LMLBT4x init\n");
3205 btwrite(0x000000, BT848_GPIO_REG_INP);
3206 gpio_inout(0xffffff, 0x0006C0);
3207 gpio_write(0x000000);
3208 }
3209
sigmaSQ_muxsel(struct bttv * btv,unsigned int input)3210 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input)
3211 {
3212 unsigned int inmux = input % 8;
3213 gpio_inout( 0xf, 0xf );
3214 gpio_bits( 0xf, inmux );
3215 }
3216
sigmaSLC_muxsel(struct bttv * btv,unsigned int input)3217 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input)
3218 {
3219 unsigned int inmux = input % 4;
3220 gpio_inout( 3<<9, 3<<9 );
3221 gpio_bits( 3<<9, inmux<<9 );
3222 }
3223
geovision_muxsel(struct bttv * btv,unsigned int input)3224 static void geovision_muxsel(struct bttv *btv, unsigned int input)
3225 {
3226 unsigned int inmux = input % 16;
3227 gpio_inout(0xf, 0xf);
3228 gpio_bits(0xf, inmux);
3229 }
3230
3231 /*
3232 * The TD3116 has 2 74HC4051 muxes wired to the MUX0 input of a bt878.
3233 * The first 74HC4051 has the lower 8 inputs, the second one the higher 8.
3234 * The muxes are controlled via a 74HC373 latch which is connected to
3235 * GPIOs 0-7. GPIO 18 is connected to the LE signal of the latch.
3236 * Q0 of the latch is connected to the Enable (~E) input of the first
3237 * 74HC4051. Q1 - Q3 are connected to S0 - S2 of the same 74HC4051.
3238 * Q4 - Q7 are connected to the second 74HC4051 in the same way.
3239 */
3240
td3116_latch_value(struct bttv * btv,u32 value)3241 static void td3116_latch_value(struct bttv *btv, u32 value)
3242 {
3243 gpio_bits((1<<18) | 0xff, value);
3244 gpio_bits((1<<18) | 0xff, (1<<18) | value);
3245 udelay(1);
3246 gpio_bits((1<<18) | 0xff, value);
3247 }
3248
td3116_muxsel(struct bttv * btv,unsigned int input)3249 static void td3116_muxsel(struct bttv *btv, unsigned int input)
3250 {
3251 u32 value;
3252 u32 highbit;
3253
3254 highbit = (input & 0x8) >> 3 ;
3255
3256 /* Disable outputs and set value in the mux */
3257 value = 0x11; /* Disable outputs */
3258 value |= ((input & 0x7) << 1) << (4 * highbit);
3259 td3116_latch_value(btv, value);
3260
3261 /* Enable the correct output */
3262 value &= ~0x11;
3263 value |= ((highbit ^ 0x1) << 4) | highbit;
3264 td3116_latch_value(btv, value);
3265 }
3266
3267 /* ----------------------------------------------------------------------- */
3268
bttv_reset_audio(struct bttv * btv)3269 static void bttv_reset_audio(struct bttv *btv)
3270 {
3271 /*
3272 * BT878A has a audio-reset register.
3273 * 1. This register is an audio reset function but it is in
3274 * function-0 (video capture) address space.
3275 * 2. It is enough to do this once per power-up of the card.
3276 * 3. There is a typo in the Conexant doc -- it is not at
3277 * 0x5B, but at 0x058. (B is an odd-number, obviously a typo!).
3278 * --//Shrikumar 030609
3279 */
3280 if (btv->id != 878)
3281 return;
3282
3283 if (bttv_debug)
3284 pr_debug("%d: BT878A ARESET\n", btv->c.nr);
3285 btwrite((1<<7), 0x058);
3286 udelay(10);
3287 btwrite( 0, 0x058);
3288 }
3289
3290 /* initialization part one -- before registering i2c bus */
bttv_init_card1(struct bttv * btv)3291 void bttv_init_card1(struct bttv *btv)
3292 {
3293 switch (btv->c.type) {
3294 case BTTV_BOARD_HAUPPAUGE:
3295 case BTTV_BOARD_HAUPPAUGE878:
3296 boot_msp34xx(btv,5);
3297 break;
3298 case BTTV_BOARD_VOODOOTV_200:
3299 case BTTV_BOARD_VOODOOTV_FM:
3300 boot_msp34xx(btv,20);
3301 break;
3302 case BTTV_BOARD_AVERMEDIA98:
3303 boot_msp34xx(btv,11);
3304 break;
3305 case BTTV_BOARD_HAUPPAUGEPVR:
3306 pvr_boot(btv);
3307 break;
3308 case BTTV_BOARD_TWINHAN_DST:
3309 case BTTV_BOARD_AVDVBT_771:
3310 case BTTV_BOARD_PINNACLESAT:
3311 btv->use_i2c_hw = 1;
3312 break;
3313 case BTTV_BOARD_ADLINK_RTV24:
3314 init_RTV24( btv );
3315 break;
3316 case BTTV_BOARD_PCI_8604PW:
3317 init_PCI8604PW(btv);
3318 break;
3319
3320 }
3321 if (!bttv_tvcards[btv->c.type].has_dvb)
3322 bttv_reset_audio(btv);
3323 }
3324
3325 /* initialization part two -- after registering i2c bus */
bttv_init_card2(struct bttv * btv)3326 void bttv_init_card2(struct bttv *btv)
3327 {
3328 btv->tuner_type = UNSET;
3329
3330 if (BTTV_BOARD_UNKNOWN == btv->c.type) {
3331 bttv_readee(btv,eeprom_data,0xa0);
3332 identify_by_eeprom(btv,eeprom_data);
3333 }
3334
3335 switch (btv->c.type) {
3336 case BTTV_BOARD_MIRO:
3337 case BTTV_BOARD_MIROPRO:
3338 case BTTV_BOARD_PINNACLE:
3339 case BTTV_BOARD_PINNACLEPRO:
3340 /* miro/pinnacle */
3341 miro_pinnacle_gpio(btv);
3342 break;
3343 case BTTV_BOARD_FLYVIDEO_98:
3344 case BTTV_BOARD_MAXI:
3345 case BTTV_BOARD_LIFE_FLYKIT:
3346 case BTTV_BOARD_FLYVIDEO:
3347 case BTTV_BOARD_TYPHOON_TVIEW:
3348 case BTTV_BOARD_CHRONOS_VS2:
3349 case BTTV_BOARD_FLYVIDEO_98FM:
3350 case BTTV_BOARD_FLYVIDEO2000:
3351 case BTTV_BOARD_FLYVIDEO98EZ:
3352 case BTTV_BOARD_CONFERENCETV:
3353 case BTTV_BOARD_LIFETEC_9415:
3354 flyvideo_gpio(btv);
3355 break;
3356 case BTTV_BOARD_HAUPPAUGE:
3357 case BTTV_BOARD_HAUPPAUGE878:
3358 case BTTV_BOARD_HAUPPAUGEPVR:
3359 /* pick up some config infos from the eeprom */
3360 bttv_readee(btv,eeprom_data,0xa0);
3361 hauppauge_eeprom(btv);
3362 break;
3363 case BTTV_BOARD_AVERMEDIA98:
3364 case BTTV_BOARD_AVPHONE98:
3365 bttv_readee(btv,eeprom_data,0xa0);
3366 avermedia_eeprom(btv);
3367 break;
3368 case BTTV_BOARD_PXC200:
3369 init_PXC200(btv);
3370 break;
3371 case BTTV_BOARD_PICOLO_TETRA_CHIP:
3372 picolo_tetra_init(btv);
3373 break;
3374 case BTTV_BOARD_VHX:
3375 btv->has_radio = 1;
3376 btv->has_tea575x = 1;
3377 btv->tea_gpio.wren = 5;
3378 btv->tea_gpio.most = 6;
3379 btv->tea_gpio.clk = 3;
3380 btv->tea_gpio.data = 4;
3381 tea575x_init(btv);
3382 break;
3383 case BTTV_BOARD_VOBIS_BOOSTAR:
3384 case BTTV_BOARD_TERRATV:
3385 terratec_active_radio_upgrade(btv);
3386 break;
3387 case BTTV_BOARD_MAGICTVIEW061:
3388 if (btv->cardid == 0x3002144f) {
3389 btv->has_radio=1;
3390 pr_info("%d: radio detected by subsystem id (CPH05x)\n",
3391 btv->c.nr);
3392 }
3393 break;
3394 case BTTV_BOARD_STB2:
3395 if (btv->cardid == 0x3060121a) {
3396 /* Fix up entry for 3DFX VoodooTV 100,
3397 which is an OEM STB card variant. */
3398 btv->has_radio=0;
3399 btv->tuner_type=TUNER_TEMIC_NTSC;
3400 }
3401 break;
3402 case BTTV_BOARD_OSPREY1x0:
3403 case BTTV_BOARD_OSPREY1x0_848:
3404 case BTTV_BOARD_OSPREY101_848:
3405 case BTTV_BOARD_OSPREY1x1:
3406 case BTTV_BOARD_OSPREY1x1_SVID:
3407 case BTTV_BOARD_OSPREY2xx:
3408 case BTTV_BOARD_OSPREY2x0_SVID:
3409 case BTTV_BOARD_OSPREY2x0:
3410 case BTTV_BOARD_OSPREY440:
3411 case BTTV_BOARD_OSPREY500:
3412 case BTTV_BOARD_OSPREY540:
3413 case BTTV_BOARD_OSPREY2000:
3414 bttv_readee(btv,eeprom_data,0xa0);
3415 osprey_eeprom(btv, eeprom_data);
3416 break;
3417 case BTTV_BOARD_IDS_EAGLE:
3418 init_ids_eagle(btv);
3419 break;
3420 case BTTV_BOARD_MODTEC_205:
3421 bttv_readee(btv,eeprom_data,0xa0);
3422 modtec_eeprom(btv);
3423 break;
3424 case BTTV_BOARD_LMLBT4:
3425 init_lmlbt4x(btv);
3426 break;
3427 case BTTV_BOARD_TIBET_CS16:
3428 tibetCS16_init(btv);
3429 break;
3430 case BTTV_BOARD_KODICOM_4400R:
3431 kodicom4400r_init(btv);
3432 break;
3433 case BTTV_BOARD_GEOVISION_GV800S:
3434 gv800s_init(btv);
3435 break;
3436 }
3437
3438 /* pll configuration */
3439 if (!(btv->id==848 && btv->revision==0x11)) {
3440 /* defaults from card list */
3441 if (PLL_28 == bttv_tvcards[btv->c.type].pll) {
3442 btv->pll.pll_ifreq=28636363;
3443 btv->pll.pll_crystal=BT848_IFORM_XT0;
3444 }
3445 if (PLL_35 == bttv_tvcards[btv->c.type].pll) {
3446 btv->pll.pll_ifreq=35468950;
3447 btv->pll.pll_crystal=BT848_IFORM_XT1;
3448 }
3449 if (PLL_14 == bttv_tvcards[btv->c.type].pll) {
3450 btv->pll.pll_ifreq = 14318181;
3451 btv->pll.pll_crystal = BT848_IFORM_XT0;
3452 }
3453 /* insmod options can override */
3454 switch (pll[btv->c.nr]) {
3455 case 0: /* none */
3456 btv->pll.pll_crystal = 0;
3457 btv->pll.pll_ifreq = 0;
3458 btv->pll.pll_ofreq = 0;
3459 break;
3460 case 1: /* 28 MHz */
3461 case 28:
3462 btv->pll.pll_ifreq = 28636363;
3463 btv->pll.pll_ofreq = 0;
3464 btv->pll.pll_crystal = BT848_IFORM_XT0;
3465 break;
3466 case 2: /* 35 MHz */
3467 case 35:
3468 btv->pll.pll_ifreq = 35468950;
3469 btv->pll.pll_ofreq = 0;
3470 btv->pll.pll_crystal = BT848_IFORM_XT1;
3471 break;
3472 case 3: /* 14 MHz */
3473 case 14:
3474 btv->pll.pll_ifreq = 14318181;
3475 btv->pll.pll_ofreq = 0;
3476 btv->pll.pll_crystal = BT848_IFORM_XT0;
3477 break;
3478 }
3479 }
3480 btv->pll.pll_current = -1;
3481
3482 /* tuner configuration (from card list / autodetect / insmod option) */
3483 if (UNSET != bttv_tvcards[btv->c.type].tuner_type)
3484 if (UNSET == btv->tuner_type)
3485 btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type;
3486 if (UNSET != tuner[btv->c.nr])
3487 btv->tuner_type = tuner[btv->c.nr];
3488
3489 if (btv->tuner_type == TUNER_ABSENT)
3490 pr_info("%d: tuner absent\n", btv->c.nr);
3491 else if (btv->tuner_type == UNSET)
3492 pr_warn("%d: tuner type unset\n", btv->c.nr);
3493 else
3494 pr_info("%d: tuner type=%d\n", btv->c.nr, btv->tuner_type);
3495
3496 if (autoload != UNSET) {
3497 pr_warn("%d: the autoload option is obsolete\n", btv->c.nr);
3498 pr_warn("%d: use option msp3400, tda7432 or tvaudio to override which audio module should be used\n",
3499 btv->c.nr);
3500 }
3501
3502 if (UNSET == btv->tuner_type)
3503 btv->tuner_type = TUNER_ABSENT;
3504
3505 btv->dig = bttv_tvcards[btv->c.type].has_dig_in ?
3506 bttv_tvcards[btv->c.type].video_inputs - 1 : UNSET;
3507 btv->svhs = bttv_tvcards[btv->c.type].svhs == NO_SVHS ?
3508 UNSET : bttv_tvcards[btv->c.type].svhs;
3509 if (svhs[btv->c.nr] != UNSET)
3510 btv->svhs = svhs[btv->c.nr];
3511 if (remote[btv->c.nr] != UNSET)
3512 btv->has_remote = remote[btv->c.nr];
3513
3514 if (bttv_tvcards[btv->c.type].has_radio)
3515 btv->has_radio = 1;
3516 if (bttv_tvcards[btv->c.type].has_remote)
3517 btv->has_remote = 1;
3518 if (!bttv_tvcards[btv->c.type].no_gpioirq)
3519 btv->gpioirq = 1;
3520 if (bttv_tvcards[btv->c.type].volume_gpio)
3521 btv->volume_gpio = bttv_tvcards[btv->c.type].volume_gpio;
3522 if (bttv_tvcards[btv->c.type].audio_mode_gpio)
3523 btv->audio_mode_gpio = bttv_tvcards[btv->c.type].audio_mode_gpio;
3524
3525 if (btv->tuner_type == TUNER_ABSENT)
3526 return; /* no tuner or related drivers to load */
3527
3528 if (btv->has_saa6588 || saa6588[btv->c.nr]) {
3529 /* Probe for RDS receiver chip */
3530 static const unsigned short addrs[] = {
3531 0x20 >> 1,
3532 0x22 >> 1,
3533 I2C_CLIENT_END
3534 };
3535 struct v4l2_subdev *sd;
3536
3537 sd = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3538 &btv->c.i2c_adap, "saa6588", 0, addrs);
3539 btv->has_saa6588 = (sd != NULL);
3540 }
3541
3542 /* try to detect audio/fader chips */
3543
3544 /* First check if the user specified the audio chip via a module
3545 option. */
3546
3547 switch (audiodev[btv->c.nr]) {
3548 case -1:
3549 return; /* do not load any audio module */
3550
3551 case 0: /* autodetect */
3552 break;
3553
3554 case 1: {
3555 /* The user specified that we should probe for msp3400 */
3556 static const unsigned short addrs[] = {
3557 I2C_ADDR_MSP3400 >> 1,
3558 I2C_ADDR_MSP3400_ALT >> 1,
3559 I2C_CLIENT_END
3560 };
3561
3562 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3563 &btv->c.i2c_adap, "msp3400", 0, addrs);
3564 if (btv->sd_msp34xx)
3565 return;
3566 goto no_audio;
3567 }
3568
3569 case 2: {
3570 /* The user specified that we should probe for tda7432 */
3571 static const unsigned short addrs[] = {
3572 I2C_ADDR_TDA7432 >> 1,
3573 I2C_CLIENT_END
3574 };
3575
3576 if (v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3577 &btv->c.i2c_adap, "tda7432", 0, addrs))
3578 return;
3579 goto no_audio;
3580 }
3581
3582 case 3: {
3583 /* The user specified that we should probe for tvaudio */
3584 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3585 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3586 if (btv->sd_tvaudio)
3587 return;
3588 goto no_audio;
3589 }
3590
3591 default:
3592 pr_warn("%d: unknown audiodev value!\n", btv->c.nr);
3593 return;
3594 }
3595
3596 /* There were no overrides, so now we try to discover this through the
3597 card definition */
3598
3599 /* probe for msp3400 first: this driver can detect whether or not
3600 it really is a msp3400, so it will return NULL when the device
3601 found is really something else (e.g. a tea6300). */
3602 if (!bttv_tvcards[btv->c.type].no_msp34xx) {
3603 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3604 &btv->c.i2c_adap, "msp3400",
3605 0, I2C_ADDRS(I2C_ADDR_MSP3400 >> 1));
3606 } else if (bttv_tvcards[btv->c.type].msp34xx_alt) {
3607 btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3608 &btv->c.i2c_adap, "msp3400",
3609 0, I2C_ADDRS(I2C_ADDR_MSP3400_ALT >> 1));
3610 }
3611
3612 /* If we found a msp34xx, then we're done. */
3613 if (btv->sd_msp34xx)
3614 return;
3615
3616 /* Now see if we can find one of the tvaudio devices. */
3617 btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3618 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3619 if (btv->sd_tvaudio) {
3620 /* There may be two tvaudio chips on the card, so try to
3621 find another. */
3622 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3623 &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3624 }
3625
3626 /* it might also be a tda7432. */
3627 if (!bttv_tvcards[btv->c.type].no_tda7432) {
3628 static const unsigned short addrs[] = {
3629 I2C_ADDR_TDA7432 >> 1,
3630 I2C_CLIENT_END
3631 };
3632
3633 btv->sd_tda7432 = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3634 &btv->c.i2c_adap, "tda7432", 0, addrs);
3635 if (btv->sd_tda7432)
3636 return;
3637 }
3638 if (btv->sd_tvaudio)
3639 return;
3640
3641 no_audio:
3642 pr_warn("%d: audio absent, no audio device found!\n", btv->c.nr);
3643 }
3644
3645
3646 /* initialize the tuner */
bttv_init_tuner(struct bttv * btv)3647 void bttv_init_tuner(struct bttv *btv)
3648 {
3649 int addr = ADDR_UNSET;
3650
3651 if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr)
3652 addr = bttv_tvcards[btv->c.type].tuner_addr;
3653
3654 if (btv->tuner_type != TUNER_ABSENT) {
3655 struct tuner_setup tun_setup;
3656
3657 /* Load tuner module before issuing tuner config call! */
3658 if (btv->has_radio)
3659 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3660 &btv->c.i2c_adap, "tuner",
3661 0, v4l2_i2c_tuner_addrs(ADDRS_RADIO));
3662 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3663 &btv->c.i2c_adap, "tuner",
3664 0, v4l2_i2c_tuner_addrs(ADDRS_DEMOD));
3665 v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3666 &btv->c.i2c_adap, "tuner",
3667 0, v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD));
3668
3669 tun_setup.mode_mask = T_ANALOG_TV;
3670 tun_setup.type = btv->tuner_type;
3671 tun_setup.addr = addr;
3672
3673 if (btv->has_radio)
3674 tun_setup.mode_mask |= T_RADIO;
3675
3676 bttv_call_all(btv, tuner, s_type_addr, &tun_setup);
3677 }
3678
3679 if (btv->tda9887_conf) {
3680 struct v4l2_priv_tun_config tda9887_cfg;
3681
3682 tda9887_cfg.tuner = TUNER_TDA9887;
3683 tda9887_cfg.priv = &btv->tda9887_conf;
3684
3685 bttv_call_all(btv, tuner, s_config, &tda9887_cfg);
3686 }
3687 }
3688
3689 /* ----------------------------------------------------------------------- */
3690
modtec_eeprom(struct bttv * btv)3691 static void modtec_eeprom(struct bttv *btv)
3692 {
3693 if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) {
3694 btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I;
3695 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3696 btv->c.nr, &eeprom_data[0x1e]);
3697 } else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) {
3698 btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I;
3699 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3700 btv->c.nr, &eeprom_data[0x1e]);
3701 } else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) {
3702 btv->tuner_type=TUNER_PHILIPS_NTSC;
3703 pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3704 btv->c.nr, &eeprom_data[0x1e]);
3705 } else {
3706 pr_info("%d: Modtec: Unknown TunerString: %s\n",
3707 btv->c.nr, &eeprom_data[0x1e]);
3708 }
3709 }
3710
hauppauge_eeprom(struct bttv * btv)3711 static void hauppauge_eeprom(struct bttv *btv)
3712 {
3713 struct tveeprom tv;
3714
3715 tveeprom_hauppauge_analog(&tv, eeprom_data);
3716 btv->tuner_type = tv.tuner_type;
3717 btv->has_radio = tv.has_radio;
3718
3719 pr_info("%d: Hauppauge eeprom indicates model#%d\n",
3720 btv->c.nr, tv.model);
3721
3722 /*
3723 * Some of the 878 boards have duplicate PCI IDs. Switch the board
3724 * type based on model #.
3725 */
3726 if(tv.model == 64900) {
3727 pr_info("%d: Switching board type from %s to %s\n",
3728 btv->c.nr,
3729 bttv_tvcards[btv->c.type].name,
3730 bttv_tvcards[BTTV_BOARD_HAUPPAUGE_IMPACTVCB].name);
3731 btv->c.type = BTTV_BOARD_HAUPPAUGE_IMPACTVCB;
3732 }
3733
3734 /* The 61334 needs the msp3410 to do the radio demod to get sound */
3735 if (tv.model == 61334)
3736 btv->radio_uses_msp_demodulator = 1;
3737 }
3738
3739 /* ----------------------------------------------------------------------- */
3740
bttv_tea575x_set_pins(struct snd_tea575x * tea,u8 pins)3741 static void bttv_tea575x_set_pins(struct snd_tea575x *tea, u8 pins)
3742 {
3743 struct bttv *btv = tea->private_data;
3744 struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3745 u16 val = 0;
3746
3747 val |= (pins & TEA575X_DATA) ? (1 << gpio.data) : 0;
3748 val |= (pins & TEA575X_CLK) ? (1 << gpio.clk) : 0;
3749 val |= (pins & TEA575X_WREN) ? (1 << gpio.wren) : 0;
3750
3751 gpio_bits((1 << gpio.data) | (1 << gpio.clk) | (1 << gpio.wren), val);
3752 if (btv->mbox_ior) {
3753 /* IOW and CSEL active */
3754 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
3755 udelay(5);
3756 /* all inactive */
3757 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
3758 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
3759 }
3760 }
3761
bttv_tea575x_get_pins(struct snd_tea575x * tea)3762 static u8 bttv_tea575x_get_pins(struct snd_tea575x *tea)
3763 {
3764 struct bttv *btv = tea->private_data;
3765 struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3766 u8 ret = 0;
3767 u16 val;
3768
3769 if (btv->mbox_ior) {
3770 /* IOR and CSEL active */
3771 gpio_bits(btv->mbox_ior | btv->mbox_csel, 0);
3772 udelay(5);
3773 }
3774 val = gpio_read();
3775 if (btv->mbox_ior) {
3776 /* all inactive */
3777 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
3778 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
3779 }
3780
3781 if (val & (1 << gpio.data))
3782 ret |= TEA575X_DATA;
3783 if (val & (1 << gpio.most))
3784 ret |= TEA575X_MOST;
3785
3786 return ret;
3787 }
3788
bttv_tea575x_set_direction(struct snd_tea575x * tea,bool output)3789 static void bttv_tea575x_set_direction(struct snd_tea575x *tea, bool output)
3790 {
3791 struct bttv *btv = tea->private_data;
3792 struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3793 u32 mask = (1 << gpio.clk) | (1 << gpio.wren) | (1 << gpio.data) |
3794 (1 << gpio.most);
3795
3796 if (output)
3797 gpio_inout(mask, (1 << gpio.data) | (1 << gpio.clk) |
3798 (1 << gpio.wren));
3799 else
3800 gpio_inout(mask, (1 << gpio.clk) | (1 << gpio.wren));
3801 }
3802
3803 static const struct snd_tea575x_ops bttv_tea_ops = {
3804 .set_pins = bttv_tea575x_set_pins,
3805 .get_pins = bttv_tea575x_get_pins,
3806 .set_direction = bttv_tea575x_set_direction,
3807 };
3808
tea575x_init(struct bttv * btv)3809 static int tea575x_init(struct bttv *btv)
3810 {
3811 btv->tea.private_data = btv;
3812 btv->tea.ops = &bttv_tea_ops;
3813 if (!snd_tea575x_hw_init(&btv->tea)) {
3814 pr_info("%d: detected TEA575x radio\n", btv->c.nr);
3815 btv->tea.mute = false;
3816 return 0;
3817 }
3818
3819 btv->has_tea575x = 0;
3820 btv->has_radio = 0;
3821
3822 return -ENODEV;
3823 }
3824
3825 /* ----------------------------------------------------------------------- */
3826
terratec_active_radio_upgrade(struct bttv * btv)3827 static int terratec_active_radio_upgrade(struct bttv *btv)
3828 {
3829 btv->has_radio = 1;
3830 btv->has_tea575x = 1;
3831 btv->tea_gpio.wren = 4;
3832 btv->tea_gpio.most = 5;
3833 btv->tea_gpio.clk = 3;
3834 btv->tea_gpio.data = 2;
3835
3836 btv->mbox_iow = 1 << 8;
3837 btv->mbox_ior = 1 << 9;
3838 btv->mbox_csel = 1 << 10;
3839
3840 if (!tea575x_init(btv)) {
3841 pr_info("%d: Terratec Active Radio Upgrade found\n", btv->c.nr);
3842 btv->has_saa6588 = 1;
3843 }
3844
3845 return 0;
3846 }
3847
3848
3849 /* ----------------------------------------------------------------------- */
3850
3851 /*
3852 * minimal bootstrap for the WinTV/PVR -- upload altera firmware.
3853 *
3854 * The hcwamc.rbf firmware file is on the Hauppauge driver CD. Have
3855 * a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be
3856 * unpacked with unzip).
3857 */
3858 #define PVR_GPIO_DELAY 10
3859
3860 #define BTTV_ALT_DATA 0x000001
3861 #define BTTV_ALT_DCLK 0x100000
3862 #define BTTV_ALT_NCONFIG 0x800000
3863
pvr_altera_load(struct bttv * btv,const u8 * micro,u32 microlen)3864 static int pvr_altera_load(struct bttv *btv, const u8 *micro, u32 microlen)
3865 {
3866 u32 n;
3867 u8 bits;
3868 int i;
3869
3870 gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG);
3871 gpio_write(0);
3872 udelay(PVR_GPIO_DELAY);
3873
3874 gpio_write(BTTV_ALT_NCONFIG);
3875 udelay(PVR_GPIO_DELAY);
3876
3877 for (n = 0; n < microlen; n++) {
3878 bits = micro[n];
3879 for (i = 0 ; i < 8 ; i++) {
3880 gpio_bits(BTTV_ALT_DCLK,0);
3881 if (bits & 0x01)
3882 gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA);
3883 else
3884 gpio_bits(BTTV_ALT_DATA,0);
3885 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3886 bits >>= 1;
3887 }
3888 }
3889 gpio_bits(BTTV_ALT_DCLK,0);
3890 udelay(PVR_GPIO_DELAY);
3891
3892 /* begin Altera init loop (Not necessary,but doesn't hurt) */
3893 for (i = 0 ; i < 30 ; i++) {
3894 gpio_bits(BTTV_ALT_DCLK,0);
3895 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3896 }
3897 gpio_bits(BTTV_ALT_DCLK,0);
3898 return 0;
3899 }
3900
pvr_boot(struct bttv * btv)3901 static int pvr_boot(struct bttv *btv)
3902 {
3903 const struct firmware *fw_entry;
3904 int rc;
3905
3906 rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev);
3907 if (rc != 0) {
3908 pr_warn("%d: no altera firmware [via hotplug]\n", btv->c.nr);
3909 return rc;
3910 }
3911 rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size);
3912 pr_info("%d: altera firmware upload %s\n",
3913 btv->c.nr, (rc < 0) ? "failed" : "ok");
3914 release_firmware(fw_entry);
3915 return rc;
3916 }
3917
3918 /* ----------------------------------------------------------------------- */
3919 /* some osprey specific stuff */
3920
osprey_eeprom(struct bttv * btv,const u8 ee[256])3921 static void osprey_eeprom(struct bttv *btv, const u8 ee[256])
3922 {
3923 int i;
3924 u32 serial = 0;
3925 int cardid = -1;
3926
3927 /* This code will nevery actually get called in this case.... */
3928 if (btv->c.type == BTTV_BOARD_UNKNOWN) {
3929 /* this might be an antique... check for MMAC label in eeprom */
3930 if (!strncmp(ee, "MMAC", 4)) {
3931 u8 checksum = 0;
3932 for (i = 0; i < 21; i++)
3933 checksum += ee[i];
3934 if (checksum != ee[21])
3935 return;
3936 cardid = BTTV_BOARD_OSPREY1x0_848;
3937 for (i = 12; i < 21; i++)
3938 serial *= 10, serial += ee[i] - '0';
3939 }
3940 } else {
3941 unsigned short type;
3942
3943 for (i = 4 * 16; i < 8 * 16; i += 16) {
3944 u16 checksum = (__force u16)ip_compute_csum(ee + i, 16);
3945
3946 if ((checksum & 0xff) + (checksum >> 8) == 0xff)
3947 break;
3948 }
3949 if (i >= 8*16)
3950 return;
3951 ee += i;
3952
3953 /* found a valid descriptor */
3954 type = get_unaligned_be16((__be16 *)(ee+4));
3955
3956 switch(type) {
3957 /* 848 based */
3958 case 0x0004:
3959 cardid = BTTV_BOARD_OSPREY1x0_848;
3960 break;
3961 case 0x0005:
3962 cardid = BTTV_BOARD_OSPREY101_848;
3963 break;
3964
3965 /* 878 based */
3966 case 0x0012:
3967 case 0x0013:
3968 cardid = BTTV_BOARD_OSPREY1x0;
3969 break;
3970 case 0x0014:
3971 case 0x0015:
3972 cardid = BTTV_BOARD_OSPREY1x1;
3973 break;
3974 case 0x0016:
3975 case 0x0017:
3976 case 0x0020:
3977 cardid = BTTV_BOARD_OSPREY1x1_SVID;
3978 break;
3979 case 0x0018:
3980 case 0x0019:
3981 case 0x001E:
3982 case 0x001F:
3983 cardid = BTTV_BOARD_OSPREY2xx;
3984 break;
3985 case 0x001A:
3986 case 0x001B:
3987 cardid = BTTV_BOARD_OSPREY2x0_SVID;
3988 break;
3989 case 0x0040:
3990 cardid = BTTV_BOARD_OSPREY500;
3991 break;
3992 case 0x0050:
3993 case 0x0056:
3994 cardid = BTTV_BOARD_OSPREY540;
3995 /* bttv_osprey_540_init(btv); */
3996 break;
3997 case 0x0060:
3998 case 0x0070:
3999 case 0x00A0:
4000 cardid = BTTV_BOARD_OSPREY2x0;
4001 /* enable output on select control lines */
4002 gpio_inout(0xffffff,0x000303);
4003 break;
4004 case 0x00D8:
4005 cardid = BTTV_BOARD_OSPREY440;
4006 break;
4007 default:
4008 /* unknown...leave generic, but get serial # */
4009 pr_info("%d: osprey eeprom: unknown card type 0x%04x\n",
4010 btv->c.nr, type);
4011 break;
4012 }
4013 serial = get_unaligned_be32((__be32 *)(ee+6));
4014 }
4015
4016 pr_info("%d: osprey eeprom: card=%d '%s' serial=%u\n",
4017 btv->c.nr, cardid,
4018 cardid > 0 ? bttv_tvcards[cardid].name : "Unknown", serial);
4019
4020 if (cardid<0 || btv->c.type == cardid)
4021 return;
4022
4023 /* card type isn't set correctly */
4024 if (card[btv->c.nr] < bttv_num_tvcards) {
4025 pr_warn("%d: osprey eeprom: Not overriding user specified card type\n",
4026 btv->c.nr);
4027 } else {
4028 pr_info("%d: osprey eeprom: Changing card type from %d to %d\n",
4029 btv->c.nr, btv->c.type, cardid);
4030 btv->c.type = cardid;
4031 }
4032 }
4033
4034 /* ----------------------------------------------------------------------- */
4035 /* AVermedia specific stuff, from bktr_card.c */
4036
4037 static int tuner_0_table[] = {
4038 TUNER_PHILIPS_NTSC, TUNER_PHILIPS_PAL /* PAL-BG*/,
4039 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL /* PAL-I*/,
4040 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL,
4041 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM,
4042 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL,
4043 TUNER_PHILIPS_FM1216ME_MK3 };
4044
4045 static int tuner_1_table[] = {
4046 TUNER_TEMIC_NTSC, TUNER_TEMIC_PAL,
4047 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
4048 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
4049 TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, /* TUNER_TEMIC_SECAM */
4050 TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL};
4051
avermedia_eeprom(struct bttv * btv)4052 static void avermedia_eeprom(struct bttv *btv)
4053 {
4054 int tuner_make, tuner_tv_fm, tuner_format, tuner_type = 0;
4055
4056 tuner_make = (eeprom_data[0x41] & 0x7);
4057 tuner_tv_fm = (eeprom_data[0x41] & 0x18) >> 3;
4058 tuner_format = (eeprom_data[0x42] & 0xf0) >> 4;
4059 btv->has_remote = (eeprom_data[0x42] & 0x01);
4060
4061 if (tuner_make == 0 || tuner_make == 2)
4062 if (tuner_format <= 0x0a)
4063 tuner_type = tuner_0_table[tuner_format];
4064 if (tuner_make == 1)
4065 if (tuner_format <= 9)
4066 tuner_type = tuner_1_table[tuner_format];
4067
4068 if (tuner_make == 4)
4069 if (tuner_format == 0x09)
4070 tuner_type = TUNER_LG_NTSC_NEW_TAPC; /* TAPC-G702P */
4071
4072 pr_info("%d: Avermedia eeprom[0x%02x%02x]: tuner=",
4073 btv->c.nr, eeprom_data[0x41], eeprom_data[0x42]);
4074 if (tuner_type) {
4075 btv->tuner_type = tuner_type;
4076 pr_cont("%d", tuner_type);
4077 } else
4078 pr_cont("Unknown type");
4079 pr_cont(" radio:%s remote control:%s\n",
4080 tuner_tv_fm ? "yes" : "no",
4081 btv->has_remote ? "yes" : "no");
4082 }
4083
4084 /*
4085 * For Voodoo TV/FM and Voodoo 200. These cards' tuners use a TDA9880
4086 * analog demod, which is not I2C controlled like the newer and more common
4087 * TDA9887 series. Instead is has two tri-state input pins, S0 and S1,
4088 * that control the IF for the video and audio. Apparently, bttv GPIO
4089 * 0x10000 is connected to S0. S0 low selects a 38.9 MHz VIF for B/G/D/K/I
4090 * (i.e., PAL) while high selects 45.75 MHz for M/N (i.e., NTSC).
4091 */
bttv_tda9880_setnorm(struct bttv * btv,u32 gpiobits)4092 u32 bttv_tda9880_setnorm(struct bttv *btv, u32 gpiobits)
4093 {
4094
4095 if (btv->audio_input == TVAUDIO_INPUT_TUNER) {
4096 if (bttv_tvnorms[btv->tvnorm].v4l2_id & V4L2_STD_MN)
4097 gpiobits |= 0x10000;
4098 else
4099 gpiobits &= ~0x10000;
4100 }
4101
4102 gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpiobits);
4103 return gpiobits;
4104 }
4105
4106
4107 /*
4108 * reset/enable the MSP on some Hauppauge cards
4109 * Thanks to Kyösti Mälkki (kmalkki@cc.hut.fi)!
4110 *
4111 * Hauppauge: pin 5
4112 * Voodoo: pin 20
4113 */
boot_msp34xx(struct bttv * btv,int pin)4114 static void boot_msp34xx(struct bttv *btv, int pin)
4115 {
4116 int mask = (1 << pin);
4117
4118 gpio_inout(mask,mask);
4119 gpio_bits(mask,0);
4120 mdelay(2);
4121 udelay(500);
4122 gpio_bits(mask,mask);
4123
4124 if (bttv_gpio)
4125 bttv_gpio_tracking(btv,"msp34xx");
4126 if (bttv_verbose)
4127 pr_info("%d: Hauppauge/Voodoo msp34xx: reset line init [%d]\n",
4128 btv->c.nr, pin);
4129 }
4130
4131 /* ----------------------------------------------------------------------- */
4132 /* Imagenation L-Model PXC200 Framegrabber */
4133 /* This is basically the same procedure as
4134 * used by Alessandro Rubini in his pxc200
4135 * driver, but using BTTV functions */
4136
init_PXC200(struct bttv * btv)4137 static void init_PXC200(struct bttv *btv)
4138 {
4139 static int vals[] = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d, 0x01, 0x02,
4140 0x03, 0x04, 0x05, 0x06, 0x00 };
4141 unsigned int i;
4142 int tmp;
4143 u32 val;
4144
4145 /* Initialise GPIO-connevted stuff */
4146 gpio_inout(0xffffff, (1<<13));
4147 gpio_write(0);
4148 udelay(3);
4149 gpio_write(1<<13);
4150 /* GPIO inputs are pulled up, so no need to drive
4151 * reset pin any longer */
4152 gpio_bits(0xffffff, 0);
4153 if (bttv_gpio)
4154 bttv_gpio_tracking(btv,"pxc200");
4155
4156 /* we could/should try and reset/control the AD pots? but
4157 right now we simply turned off the crushing. Without
4158 this the AGC drifts drifts
4159 remember the EN is reverse logic -->
4160 setting BT848_ADC_AGC_EN disable the AGC
4161 tboult@eecs.lehigh.edu
4162 */
4163
4164 btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC);
4165
4166 /* Initialise MAX517 DAC */
4167 pr_info("Setting DAC reference voltage level ...\n");
4168 bttv_I2CWrite(btv,0x5E,0,0x80,1);
4169
4170 /* Initialise 12C508 PIC */
4171 /* The I2CWrite and I2CRead commands are actually to the
4172 * same chips - but the R/W bit is included in the address
4173 * argument so the numbers are different */
4174
4175
4176 pr_info("Initialising 12C508 PIC chip ...\n");
4177
4178 /* First of all, enable the clock line. This is used in the PXC200-F */
4179 val = btread(BT848_GPIO_DMA_CTL);
4180 val |= BT848_GPIO_DMA_CTL_GPCLKMODE;
4181 btwrite(val, BT848_GPIO_DMA_CTL);
4182
4183 /* Then, push to 0 the reset pin long enough to reset the *
4184 * device same as above for the reset line, but not the same
4185 * value sent to the GPIO-connected stuff
4186 * which one is the good one? */
4187 gpio_inout(0xffffff,(1<<2));
4188 gpio_write(0);
4189 udelay(10);
4190 gpio_write(1<<2);
4191
4192 for (i = 0; i < ARRAY_SIZE(vals); i++) {
4193 tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1);
4194 if (tmp != -1) {
4195 pr_info("I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n",
4196 vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL));
4197 }
4198 }
4199
4200 pr_info("PXC200 Initialised\n");
4201 }
4202
4203
4204
4205 /* ----------------------------------------------------------------------- */
4206 /*
4207 * The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock
4208 * it. This apparently involves the following procedure for each 878 chip:
4209 *
4210 * 1) write 0x00C3FEFF to the GPIO_OUT_EN register
4211 *
4212 * 2) write to GPIO_DATA
4213 * - 0x0E
4214 * - sleep 1ms
4215 * - 0x10 + 0x0E
4216 * - sleep 10ms
4217 * - 0x0E
4218 * read from GPIO_DATA into buf (uint_32)
4219 * - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 )
4220 * error. ERROR_CPLD_Check_Failed stop.
4221 *
4222 * 3) write to GPIO_DATA
4223 * - write 0x4400 + 0x0E
4224 * - sleep 10ms
4225 * - write 0x4410 + 0x0E
4226 * - sleep 1ms
4227 * - write 0x0E
4228 * read from GPIO_DATA into buf (uint_32)
4229 * - if ( buf>>18 & 0x01 ) || ( buf>>19 & 0x01 != 0 )
4230 * error. ERROR_CPLD_Check_Failed.
4231 */
4232 /* ----------------------------------------------------------------------- */
4233 static void
init_RTV24(struct bttv * btv)4234 init_RTV24 (struct bttv *btv)
4235 {
4236 uint32_t dataRead = 0;
4237 long watchdog_value = 0x0E;
4238
4239 pr_info("%d: Adlink RTV-24 initialisation in progress ...\n",
4240 btv->c.nr);
4241
4242 btwrite (0x00c3feff, BT848_GPIO_OUT_EN);
4243
4244 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4245 msleep (1);
4246 btwrite (0x10 + watchdog_value, BT848_GPIO_DATA);
4247 msleep (10);
4248 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4249
4250 dataRead = btread (BT848_GPIO_DATA);
4251
4252 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 1)) {
4253 pr_info("%d: Adlink RTV-24 initialisation(1) ERROR_CPLD_Check_Failed (read %d)\n",
4254 btv->c.nr, dataRead);
4255 }
4256
4257 btwrite (0x4400 + watchdog_value, BT848_GPIO_DATA);
4258 msleep (10);
4259 btwrite (0x4410 + watchdog_value, BT848_GPIO_DATA);
4260 msleep (1);
4261 btwrite (watchdog_value, BT848_GPIO_DATA);
4262 msleep (1);
4263 dataRead = btread (BT848_GPIO_DATA);
4264
4265 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 0)) {
4266 pr_info("%d: Adlink RTV-24 initialisation(2) ERROR_CPLD_Check_Failed (read %d)\n",
4267 btv->c.nr, dataRead);
4268
4269 return;
4270 }
4271
4272 pr_info("%d: Adlink RTV-24 initialisation complete\n", btv->c.nr);
4273 }
4274
4275
4276
4277 /* ----------------------------------------------------------------------- */
4278 /*
4279 * The PCI-8604PW contains a CPLD, probably an ispMACH 4A, that filters
4280 * the PCI REQ signals coming from the four BT878 chips. After power
4281 * up, the CPLD does not forward requests to the bus, which prevents
4282 * the BT878 from fetching RISC instructions from memory. While the
4283 * CPLD is connected to most of the GPIOs of PCI device 0xD, only
4284 * five appear to play a role in unlocking the REQ signal. The following
4285 * sequence has been determined by trial and error without access to the
4286 * original driver.
4287 *
4288 * Eight GPIOs of device 0xC are provided on connector CN4 (4 in, 4 out).
4289 * Devices 0xE and 0xF do not appear to have anything connected to their
4290 * GPIOs.
4291 *
4292 * The correct GPIO_OUT_EN value might have some more bits set. It should
4293 * be possible to derive it from a boundary scan of the CPLD. Its JTAG
4294 * pins are routed to test points.
4295 *
4296 */
4297 /* ----------------------------------------------------------------------- */
4298 static void
init_PCI8604PW(struct bttv * btv)4299 init_PCI8604PW(struct bttv *btv)
4300 {
4301 int state;
4302
4303 if ((PCI_SLOT(btv->c.pci->devfn) & ~3) != 0xC) {
4304 pr_warn("This is not a PCI-8604PW\n");
4305 return;
4306 }
4307
4308 if (PCI_SLOT(btv->c.pci->devfn) != 0xD)
4309 return;
4310
4311 btwrite(0x080002, BT848_GPIO_OUT_EN);
4312
4313 state = (btread(BT848_GPIO_DATA) >> 21) & 7;
4314
4315 for (;;) {
4316 switch (state) {
4317 case 1:
4318 case 5:
4319 case 6:
4320 case 4:
4321 pr_debug("PCI-8604PW in state %i, toggling pin\n",
4322 state);
4323 btwrite(0x080000, BT848_GPIO_DATA);
4324 msleep(1);
4325 btwrite(0x000000, BT848_GPIO_DATA);
4326 msleep(1);
4327 break;
4328 case 7:
4329 pr_info("PCI-8604PW unlocked\n");
4330 return;
4331 case 0:
4332 /* FIXME: If we are in state 7 and toggle GPIO[19] one
4333 more time, the CPLD goes into state 0, where PCI bus
4334 mastering is inhibited again. We have not managed to
4335 get out of that state. */
4336
4337 pr_err("PCI-8604PW locked until reset\n");
4338 return;
4339 default:
4340 pr_err("PCI-8604PW in unknown state %i\n", state);
4341 return;
4342 }
4343
4344 state = (state << 4) | ((btread(BT848_GPIO_DATA) >> 21) & 7);
4345
4346 switch (state) {
4347 case 0x15:
4348 case 0x56:
4349 case 0x64:
4350 case 0x47:
4351 /* The transition from state 7 to state 0 is, as explained
4352 above, valid but undesired and with this code impossible
4353 as we exit as soon as we are in state 7.
4354 case 0x70: */
4355 break;
4356 default:
4357 pr_err("PCI-8604PW invalid transition %i -> %i\n",
4358 state >> 4, state & 7);
4359 return;
4360 }
4361 state &= 7;
4362 }
4363 }
4364
4365 /* RemoteVision MX (rv605) muxsel helper [Miguel Freitas]
4366 *
4367 * This is needed because rv605 don't use a normal multiplex, but a crosspoint
4368 * switch instead (CD22M3494E). This IC can have multiple active connections
4369 * between Xn (input) and Yn (output) pins. We need to clear any existing
4370 * connection prior to establish a new one, pulsing the STROBE pin.
4371 *
4372 * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
4373 * GPIO pins are wired as:
4374 * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller)
4375 * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller)
4376 * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller)
4377 * GPIO[8] - - P3[5] (microcontroller)
4378 * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller)
4379 * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller)
4380 * GPINTR - - P3[4] (microcontroller)
4381 *
4382 * The microcontroller is a 80C32 like. It should be possible to change xpoint
4383 * configuration either directly (as we are doing) or using the microcontroller
4384 * which is also wired to I2C interface. I have no further info on the
4385 * microcontroller features, one would need to disassembly the firmware.
4386 * note: the vendor refused to give any information on this product, all
4387 * that stuff was found using a multimeter! :)
4388 */
rv605_muxsel(struct bttv * btv,unsigned int input)4389 static void rv605_muxsel(struct bttv *btv, unsigned int input)
4390 {
4391 static const u8 muxgpio[] = { 0x3, 0x1, 0x2, 0x4, 0xf, 0x7, 0xe, 0x0,
4392 0xd, 0xb, 0xc, 0x6, 0x9, 0x5, 0x8, 0xa };
4393
4394 gpio_bits(0x07f, muxgpio[input]);
4395
4396 /* reset all connections */
4397 gpio_bits(0x200,0x200);
4398 mdelay(1);
4399 gpio_bits(0x200,0x000);
4400 mdelay(1);
4401
4402 /* create a new connection */
4403 gpio_bits(0x480,0x480);
4404 mdelay(1);
4405 gpio_bits(0x480,0x080);
4406 mdelay(1);
4407 }
4408
4409 /* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning]
4410 *
4411 * The CS16 (available on eBay cheap) is a PCI board with four Fusion
4412 * 878A chips, a PCI bridge, an Atmel microcontroller, four sync separator
4413 * chips, ten eight input analog multiplexors, a not chip and a few
4414 * other components.
4415 *
4416 * 16 inputs on a secondary bracket are provided and can be selected
4417 * from each of the four capture chips. Two of the eight input
4418 * multiplexors are used to select from any of the 16 input signals.
4419 *
4420 * Unsupported hardware capabilities:
4421 * . A video output monitor on the secondary bracket can be selected from
4422 * one of the 878A chips.
4423 * . Another passthrough but I haven't spent any time investigating it.
4424 * . Digital I/O (logic level connected to GPIO) is available from an
4425 * onboard header.
4426 *
4427 * The on chip input mux should always be set to 2.
4428 * GPIO[16:19] - Video input selection
4429 * GPIO[0:3] - Video output monitor select (only available from one 878A)
4430 * GPIO[?:?] - Digital I/O.
4431 *
4432 * There is an ATMEL microcontroller with an 8031 core on board. I have not
4433 * determined what function (if any) it provides. With the microcontroller
4434 * and sync separator chips a guess is that it might have to do with video
4435 * switching and maybe some digital I/O.
4436 */
tibetCS16_muxsel(struct bttv * btv,unsigned int input)4437 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input)
4438 {
4439 /* video mux */
4440 gpio_bits(0x0f0000, input << 16);
4441 }
4442
tibetCS16_init(struct bttv * btv)4443 static void tibetCS16_init(struct bttv *btv)
4444 {
4445 /* enable gpio bits, mask obtained via btSpy */
4446 gpio_inout(0xffffff, 0x0f7fff);
4447 gpio_write(0x0f7fff);
4448 }
4449
4450 /*
4451 * The following routines for the Kodicom-4400r get a little mind-twisting.
4452 * There is a "master" controller and three "slave" controllers, together
4453 * an analog switch which connects any of 16 cameras to any of the BT87A's.
4454 * The analog switch is controlled by the "master", but the detection order
4455 * of the four BT878A chips is in an order which I just don't understand.
4456 * The "master" is actually the second controller to be detected. The
4457 * logic on the board uses logical numbers for the 4 controllers, but
4458 * those numbers are different from the detection sequence. When working
4459 * with the analog switch, we need to "map" from the detection sequence
4460 * over to the board's logical controller number. This mapping sequence
4461 * is {3, 0, 2, 1}, i.e. the first controller to be detected is logical
4462 * unit 3, the second (which is the master) is logical unit 0, etc.
4463 * We need to maintain the status of the analog switch (which of the 16
4464 * cameras is connected to which of the 4 controllers) in sw_status array.
4465 */
4466
4467 /*
4468 * First a routine to set the analog switch, which controls which camera
4469 * is routed to which controller. The switch comprises an X-address
4470 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4471 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4472 * A data value (gpio bit 7) of '1' enables the switch, and '0' disables
4473 * the switch. A STROBE bit (gpio bit 8) latches the data value into the
4474 * specified address. The idea is to set the address and data, then bring
4475 * STROBE high, and finally bring STROBE back to low.
4476 */
kodicom4400r_write(struct bttv * btv,unsigned char xaddr,unsigned char yaddr,unsigned char data)4477 static void kodicom4400r_write(struct bttv *btv,
4478 unsigned char xaddr,
4479 unsigned char yaddr,
4480 unsigned char data) {
4481 unsigned int udata;
4482
4483 udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf);
4484 gpio_bits(0x1ff, udata); /* write ADDR and DAT */
4485 gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */
4486 gpio_bits(0x1ff, udata); /* strobe low */
4487 }
4488
4489 /*
4490 * Next the mux select. Both the "master" and "slave" 'cards' (controllers)
4491 * use this routine. The routine finds the "master" for the card, maps
4492 * the controller number from the detected position over to the logical
4493 * number, writes the appropriate data to the analog switch, and housekeeps
4494 * the local copy of the switch information. The parameter 'input' is the
4495 * requested camera number (0 - 15).
4496 */
kodicom4400r_muxsel(struct bttv * btv,unsigned int input)4497 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
4498 {
4499 int xaddr, yaddr;
4500 struct bttv *mctlr;
4501 static unsigned char map[4] = {3, 0, 2, 1};
4502
4503 mctlr = master[btv->c.nr];
4504 if (mctlr == NULL) { /* ignore if master not yet detected */
4505 return;
4506 }
4507 yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */
4508 yaddr = map[yaddr];
4509 xaddr = input & 0xf;
4510 /* Check if the controller/camera pair has changed, else ignore */
4511 if (mctlr->sw_status[yaddr] != xaddr)
4512 {
4513 /* "open" the old switch, "close" the new one, save the new */
4514 kodicom4400r_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
4515 mctlr->sw_status[yaddr] = xaddr;
4516 kodicom4400r_write(mctlr, xaddr, yaddr, 1);
4517 }
4518 }
4519
4520 /*
4521 * During initialisation, we need to reset the analog switch. We
4522 * also preset the switch to map the 4 connectors on the card to the
4523 * *user's* (see above description of kodicom4400r_muxsel) channels
4524 * 0 through 3
4525 */
kodicom4400r_init(struct bttv * btv)4526 static void kodicom4400r_init(struct bttv *btv)
4527 {
4528 int ix;
4529
4530 gpio_inout(0x0003ff, 0x0003ff);
4531 gpio_write(1 << 9); /* reset MUX */
4532 gpio_write(0);
4533 /* Preset camera 0 to the 4 controllers */
4534 for (ix = 0; ix < 4; ix++) {
4535 btv->sw_status[ix] = ix;
4536 kodicom4400r_write(btv, ix, ix, 1);
4537 }
4538 /*
4539 * Since this is the "master", we need to set up the
4540 * other three controller chips' pointers to this structure
4541 * for later use in the muxsel routine.
4542 */
4543 if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3))
4544 return;
4545 master[btv->c.nr-1] = btv;
4546 master[btv->c.nr] = btv;
4547 master[btv->c.nr+1] = btv;
4548 master[btv->c.nr+2] = btv;
4549 }
4550
4551 /* The Grandtec X-Guard framegrabber card uses two Dual 4-channel
4552 * video multiplexers to provide up to 16 video inputs. These
4553 * multiplexers are controlled by the lower 8 GPIO pins of the
4554 * bt878. The multiplexers probably Pericom PI5V331Q or similar.
4555
4556 * xxx0 is pin xxx of multiplexer U5,
4557 * yyy1 is pin yyy of multiplexer U2
4558 */
4559 #define ENA0 0x01
4560 #define ENB0 0x02
4561 #define ENA1 0x04
4562 #define ENB1 0x08
4563
4564 #define IN10 0x10
4565 #define IN00 0x20
4566 #define IN11 0x40
4567 #define IN01 0x80
4568
xguard_muxsel(struct bttv * btv,unsigned int input)4569 static void xguard_muxsel(struct bttv *btv, unsigned int input)
4570 {
4571 static const int masks[] = {
4572 ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10,
4573 ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10,
4574 ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11,
4575 ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11,
4576 };
4577 gpio_write(masks[input%16]);
4578 }
picolo_tetra_init(struct bttv * btv)4579 static void picolo_tetra_init(struct bttv *btv)
4580 {
4581 /*This is the video input redirection fonctionality : I DID NOT USED IT. */
4582 btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */
4583 btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A] set to 1*/
4584 }
picolo_tetra_muxsel(struct bttv * btv,unsigned int input)4585 static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input)
4586 {
4587
4588 dprintk("%d : picolo_tetra_muxsel => input = %d\n", btv->c.nr, input);
4589 /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/
4590 /*GPIO[20]&GPIO[21] used to choose the right input*/
4591 btwrite (input<<20,BT848_GPIO_DATA);
4592
4593 }
4594
4595 /*
4596 * ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>]
4597 *
4598 * The IVC120G security card has 4 i2c controlled TDA8540 matrix
4599 * swichers to provide 16 channels to MUX0. The TDA8540's have
4600 * 4 independent outputs and as such the IVC120G also has the
4601 * optional "Monitor Out" bus. This allows the card to be looking
4602 * at one input while the monitor is looking at another.
4603 *
4604 * Since I've couldn't be bothered figuring out how to add an
4605 * independent muxsel for the monitor bus, I've just set it to
4606 * whatever the card is looking at.
4607 *
4608 * OUT0 of the TDA8540's is connected to MUX0 (0x03)
4609 * OUT1 of the TDA8540's is connected to "Monitor Out" (0x0C)
4610 *
4611 * TDA8540_ALT3 IN0-3 = Channel 13 - 16 (0x03)
4612 * TDA8540_ALT4 IN0-3 = Channel 1 - 4 (0x03)
4613 * TDA8540_ALT5 IN0-3 = Channel 5 - 8 (0x03)
4614 * TDA8540_ALT6 IN0-3 = Channel 9 - 12 (0x03)
4615 *
4616 */
4617
4618 /* All 7 possible sub-ids for the TDA8540 Matrix Switcher */
4619 #define I2C_TDA8540 0x90
4620 #define I2C_TDA8540_ALT1 0x92
4621 #define I2C_TDA8540_ALT2 0x94
4622 #define I2C_TDA8540_ALT3 0x96
4623 #define I2C_TDA8540_ALT4 0x98
4624 #define I2C_TDA8540_ALT5 0x9a
4625 #define I2C_TDA8540_ALT6 0x9c
4626
ivc120_muxsel(struct bttv * btv,unsigned int input)4627 static void ivc120_muxsel(struct bttv *btv, unsigned int input)
4628 {
4629 /* Simple maths */
4630 int key = input % 4;
4631 int matrix = input / 4;
4632
4633 dprintk("%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n",
4634 btv->c.nr, input, matrix, key);
4635
4636 /* Handles the input selection on the TDA8540's */
4637 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00,
4638 ((matrix == 3) ? (key | key << 2) : 0x00), 1);
4639 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00,
4640 ((matrix == 0) ? (key | key << 2) : 0x00), 1);
4641 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00,
4642 ((matrix == 1) ? (key | key << 2) : 0x00), 1);
4643 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00,
4644 ((matrix == 2) ? (key | key << 2) : 0x00), 1);
4645
4646 /* Handles the output enables on the TDA8540's */
4647 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02,
4648 ((matrix == 3) ? 0x03 : 0x00), 1); /* 13 - 16 */
4649 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02,
4650 ((matrix == 0) ? 0x03 : 0x00), 1); /* 1-4 */
4651 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02,
4652 ((matrix == 1) ? 0x03 : 0x00), 1); /* 5-8 */
4653 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02,
4654 ((matrix == 2) ? 0x03 : 0x00), 1); /* 9-12 */
4655
4656 /* 878's MUX0 is already selected for input via muxsel values */
4657 }
4658
4659
4660 /* PXC200 muxsel helper
4661 * luke@syseng.anu.edu.au
4662 * another transplant
4663 * from Alessandro Rubini (rubini@linux.it)
4664 *
4665 * There are 4 kinds of cards:
4666 * PXC200L which is bt848
4667 * PXC200F which is bt848 with PIC controlling mux
4668 * PXC200AL which is bt878
4669 * PXC200AF which is bt878 with PIC controlling mux
4670 */
4671 #define PX_CFG_PXC200F 0x01
4672 #define PX_FLAG_PXC200A 0x00001000 /* a pxc200A is bt-878 based */
4673 #define PX_I2C_PIC 0x0f
4674 #define PX_PXC200A_CARDID 0x200a1295
4675 #define PX_I2C_CMD_CFG 0x00
4676
PXC200_muxsel(struct bttv * btv,unsigned int input)4677 static void PXC200_muxsel(struct bttv *btv, unsigned int input)
4678 {
4679 int rc;
4680 long mux;
4681 int bitmask;
4682 unsigned char buf[2];
4683
4684 /* Read PIC config to determine if this is a PXC200F */
4685 /* PX_I2C_CMD_CFG*/
4686 buf[0]=0;
4687 buf[1]=0;
4688 rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1);
4689 if (rc) {
4690 pr_debug("%d: PXC200_muxsel: pic cfg write failed:%d\n",
4691 btv->c.nr, rc);
4692 /* not PXC ? do nothing */
4693 return;
4694 }
4695
4696 rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL);
4697 if (!(rc & PX_CFG_PXC200F)) {
4698 pr_debug("%d: PXC200_muxsel: not PXC200F rc:%d\n",
4699 btv->c.nr, rc);
4700 return;
4701 }
4702
4703
4704 /* The multiplexer in the 200F is handled by the GPIO port */
4705 /* get correct mapping between inputs */
4706 /* mux = bttv_tvcards[btv->type].muxsel[input] & 3; */
4707 /* ** not needed!? */
4708 mux = input;
4709
4710 /* make sure output pins are enabled */
4711 /* bitmask=0x30f; */
4712 bitmask=0x302;
4713 /* check whether we have a PXC200A */
4714 if (btv->cardid == PX_PXC200A_CARDID) {
4715 bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */
4716 bitmask |= 7<<4; /* the DAC */
4717 }
4718 btwrite(bitmask, BT848_GPIO_OUT_EN);
4719
4720 bitmask = btread(BT848_GPIO_DATA);
4721 if (btv->cardid == PX_PXC200A_CARDID)
4722 bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7);
4723 else /* older device */
4724 bitmask = (bitmask & ~0x300) | ((mux & 3) << 8);
4725 btwrite(bitmask,BT848_GPIO_DATA);
4726
4727 /*
4728 * Was "to be safe, set the bt848 to input 0"
4729 * Actually, since it's ok at load time, better not messing
4730 * with these bits (on PXC200AF you need to set mux 2 here)
4731 *
4732 * needed because bttv-driver sets mux before calling this function
4733 */
4734 if (btv->cardid == PX_PXC200A_CARDID)
4735 btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM);
4736 else /* older device */
4737 btand(~BT848_IFORM_MUXSEL,BT848_IFORM);
4738
4739 pr_debug("%d: setting input channel to:%d\n", btv->c.nr, (int)mux);
4740 }
4741
phytec_muxsel(struct bttv * btv,unsigned int input)4742 static void phytec_muxsel(struct bttv *btv, unsigned int input)
4743 {
4744 unsigned int mux = input % 4;
4745
4746 if (input == btv->svhs)
4747 mux = 0;
4748
4749 gpio_bits(0x3, mux);
4750 }
4751
4752 /*
4753 * GeoVision GV-800(S) functions
4754 * Bruno Christo <bchristo@inf.ufsm.br>
4755 */
4756
4757 /* This is a function to control the analog switch, which determines which
4758 * camera is routed to which controller. The switch comprises an X-address
4759 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4760 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4761 * A data value (gpio bit 18) of '1' enables the switch, and '0' disables
4762 * the switch. A STROBE bit (gpio bit 17) latches the data value into the
4763 * specified address. There is also a chip select (gpio bit 16).
4764 * The idea is to set the address and chip select together, bring
4765 * STROBE high, write the data, and finally bring STROBE back to low.
4766 */
gv800s_write(struct bttv * btv,unsigned char xaddr,unsigned char yaddr,unsigned char data)4767 static void gv800s_write(struct bttv *btv,
4768 unsigned char xaddr,
4769 unsigned char yaddr,
4770 unsigned char data) {
4771 /* On the "master" 878A:
4772 * GPIO bits 0-9 are used for the analog switch:
4773 * 00 - 03: camera selector
4774 * 04 - 06: 878A (controller) selector
4775 * 16: cselect
4776 * 17: strobe
4777 * 18: data (1->on, 0->off)
4778 * 19: reset
4779 */
4780 const u32 ADDRESS = ((xaddr&0xf) | (yaddr&3)<<4);
4781 const u32 CSELECT = 1<<16;
4782 const u32 STROBE = 1<<17;
4783 const u32 DATA = data<<18;
4784
4785 gpio_bits(0x1007f, ADDRESS | CSELECT); /* write ADDRESS and CSELECT */
4786 gpio_bits(0x20000, STROBE); /* STROBE high */
4787 gpio_bits(0x40000, DATA); /* write DATA */
4788 gpio_bits(0x20000, ~STROBE); /* STROBE low */
4789 }
4790
4791 /*
4792 * GeoVision GV-800(S) muxsel
4793 *
4794 * Each of the 4 cards (controllers) use this function.
4795 * The controller using this function selects the input through the GPIO pins
4796 * of the "master" card. A pointer to this card is stored in master[btv->c.nr].
4797 *
4798 * The parameter 'input' is the requested camera number (0-4) on the controller.
4799 * The map array has the address of each input. Note that the addresses in the
4800 * array are in the sequence the original GeoVision driver uses, that is, set
4801 * every controller to input 0, then to input 1, 2, 3, repeat. This means that
4802 * the physical "camera 1" connector corresponds to controller 0 input 0,
4803 * "camera 2" corresponds to controller 1 input 0, and so on.
4804 *
4805 * After getting the input address, the function then writes the appropriate
4806 * data to the analog switch, and housekeeps the local copy of the switch
4807 * information.
4808 */
gv800s_muxsel(struct bttv * btv,unsigned int input)4809 static void gv800s_muxsel(struct bttv *btv, unsigned int input)
4810 {
4811 struct bttv *mctlr;
4812 int xaddr, yaddr;
4813 static unsigned int map[4][4] = { { 0x0, 0x4, 0xa, 0x6 },
4814 { 0x1, 0x5, 0xb, 0x7 },
4815 { 0x2, 0x8, 0xc, 0xe },
4816 { 0x3, 0x9, 0xd, 0xf } };
4817 input = input%4;
4818 mctlr = master[btv->c.nr];
4819 if (mctlr == NULL) {
4820 /* do nothing until the "master" is detected */
4821 return;
4822 }
4823 yaddr = (btv->c.nr - mctlr->c.nr) & 3;
4824 xaddr = map[yaddr][input] & 0xf;
4825
4826 /* Check if the controller/camera pair has changed, ignore otherwise */
4827 if (mctlr->sw_status[yaddr] != xaddr) {
4828 /* disable the old switch, enable the new one and save status */
4829 gv800s_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
4830 mctlr->sw_status[yaddr] = xaddr;
4831 gv800s_write(mctlr, xaddr, yaddr, 1);
4832 }
4833 }
4834
4835 /* GeoVision GV-800(S) "master" chip init */
gv800s_init(struct bttv * btv)4836 static void gv800s_init(struct bttv *btv)
4837 {
4838 int ix;
4839
4840 gpio_inout(0xf107f, 0xf107f);
4841 gpio_write(1<<19); /* reset the analog MUX */
4842 gpio_write(0);
4843
4844 /* Preset camera 0 to the 4 controllers */
4845 for (ix = 0; ix < 4; ix++) {
4846 btv->sw_status[ix] = ix;
4847 gv800s_write(btv, ix, ix, 1);
4848 }
4849
4850 /* Inputs on the "master" controller need this brightness fix */
4851 bttv_I2CWrite(btv, 0x18, 0x5, 0x90, 1);
4852
4853 if (btv->c.nr > BTTV_MAX-4)
4854 return;
4855 /*
4856 * Store the "master" controller pointer in the master
4857 * array for later use in the muxsel function.
4858 */
4859 master[btv->c.nr] = btv;
4860 master[btv->c.nr+1] = btv;
4861 master[btv->c.nr+2] = btv;
4862 master[btv->c.nr+3] = btv;
4863 }
4864
4865 /* ----------------------------------------------------------------------- */
4866 /* motherboard chipset specific stuff */
4867
bttv_check_chipset(void)4868 void __init bttv_check_chipset(void)
4869 {
4870 int pcipci_fail = 0;
4871 struct pci_dev *dev = NULL;
4872
4873 if (pci_pci_problems & (PCIPCI_FAIL|PCIAGP_FAIL)) /* should check if target is AGP */
4874 pcipci_fail = 1;
4875 if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF))
4876 triton1 = 1;
4877 if (pci_pci_problems & PCIPCI_VSFX)
4878 vsfx = 1;
4879 #ifdef PCIPCI_ALIMAGIK
4880 if (pci_pci_problems & PCIPCI_ALIMAGIK)
4881 latency = 0x0A;
4882 #endif
4883
4884
4885 /* print warnings about any quirks found */
4886 if (triton1)
4887 pr_info("Host bridge needs ETBF enabled\n");
4888 if (vsfx)
4889 pr_info("Host bridge needs VSFX enabled\n");
4890 if (pcipci_fail) {
4891 pr_info("bttv and your chipset may not work together\n");
4892 if (!no_overlay) {
4893 pr_info("overlay will be disabled\n");
4894 no_overlay = 1;
4895 } else {
4896 pr_info("overlay forced. Use this option at your own risk.\n");
4897 }
4898 }
4899 if (UNSET != latency)
4900 pr_info("pci latency fixup [%d]\n", latency);
4901 while ((dev = pci_get_device(PCI_VENDOR_ID_INTEL,
4902 PCI_DEVICE_ID_INTEL_82441, dev))) {
4903 unsigned char b;
4904 pci_read_config_byte(dev, 0x53, &b);
4905 if (bttv_debug)
4906 pr_info("Host bridge: 82441FX Natoma, bufcon=0x%02x\n",
4907 b);
4908 }
4909 }
4910
bttv_handle_chipset(struct bttv * btv)4911 int bttv_handle_chipset(struct bttv *btv)
4912 {
4913 unsigned char command;
4914
4915 if (!triton1 && !vsfx && UNSET == latency)
4916 return 0;
4917
4918 if (bttv_verbose) {
4919 if (triton1)
4920 pr_info("%d: enabling ETBF (430FX/VP3 compatibility)\n",
4921 btv->c.nr);
4922 if (vsfx && btv->id >= 878)
4923 pr_info("%d: enabling VSFX\n", btv->c.nr);
4924 if (UNSET != latency)
4925 pr_info("%d: setting pci timer to %d\n",
4926 btv->c.nr, latency);
4927 }
4928
4929 if (btv->id < 878) {
4930 /* bt848 (mis)uses a bit in the irq mask for etbf */
4931 if (triton1)
4932 btv->triton1 = BT848_INT_ETBF;
4933 } else {
4934 /* bt878 has a bit in the pci config space for it */
4935 pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command);
4936 if (triton1)
4937 command |= BT878_EN_TBFX;
4938 if (vsfx)
4939 command |= BT878_EN_VSFX;
4940 pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command);
4941 }
4942 if (UNSET != latency)
4943 pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency);
4944 return 0;
4945 }
4946