1 // SPDX-License-Identifier: GPL-2.0+
2 #include <linux/clk.h>
3 #include <linux/component.h>
4 #include <linux/delay.h>
5 #include <linux/io.h>
6 #include <linux/mfd/syscon.h>
7 #include <linux/module.h>
8 #include <linux/of.h>
9 #include <linux/platform_device.h>
10 #include <linux/regmap.h>
11 #include <linux/regulator/consumer.h>
12 #include <video/mipi_display.h>
13
14 #include <drm/drm_atomic_helper.h>
15 #include <drm/drm_bridge.h>
16 #include <drm/drm_device.h>
17 #include <drm/drm_drv.h>
18 #include <drm/drm_encoder.h>
19 #include <drm/drm_mipi_dsi.h>
20 #include <drm/drm_modeset_helper_vtables.h>
21 #include <drm/drm_of.h>
22 #include <drm/drm_panel.h>
23 #include <drm/drm_print.h>
24 #include <drm/drm_probe_helper.h>
25
26 #include "mcde_drm.h"
27 #include "mcde_dsi_regs.h"
28
29 #define DSI_DEFAULT_LP_FREQ_HZ 19200000
30 #define DSI_DEFAULT_HS_FREQ_HZ 420160000
31
32 /* PRCMU DSI reset registers */
33 #define PRCM_DSI_SW_RESET 0x324
34 #define PRCM_DSI_SW_RESET_DSI0_SW_RESETN BIT(0)
35 #define PRCM_DSI_SW_RESET_DSI1_SW_RESETN BIT(1)
36 #define PRCM_DSI_SW_RESET_DSI2_SW_RESETN BIT(2)
37
38 struct mcde_dsi {
39 struct device *dev;
40 struct mcde *mcde;
41 struct drm_bridge bridge;
42 struct drm_panel *panel;
43 struct drm_bridge *bridge_out;
44 struct mipi_dsi_host dsi_host;
45 struct mipi_dsi_device *mdsi;
46 const struct drm_display_mode *mode;
47 struct clk *hs_clk;
48 struct clk *lp_clk;
49 unsigned long hs_freq;
50 unsigned long lp_freq;
51 bool unused;
52
53 void __iomem *regs;
54 struct regmap *prcmu;
55 };
56
bridge_to_mcde_dsi(struct drm_bridge * bridge)57 static inline struct mcde_dsi *bridge_to_mcde_dsi(struct drm_bridge *bridge)
58 {
59 return container_of(bridge, struct mcde_dsi, bridge);
60 }
61
host_to_mcde_dsi(struct mipi_dsi_host * h)62 static inline struct mcde_dsi *host_to_mcde_dsi(struct mipi_dsi_host *h)
63 {
64 return container_of(h, struct mcde_dsi, dsi_host);
65 }
66
mcde_dsi_irq(struct mipi_dsi_device * mdsi)67 bool mcde_dsi_irq(struct mipi_dsi_device *mdsi)
68 {
69 struct mcde_dsi *d;
70 u32 val;
71 bool te_received = false;
72
73 d = host_to_mcde_dsi(mdsi->host);
74
75 dev_dbg(d->dev, "%s called\n", __func__);
76
77 val = readl(d->regs + DSI_DIRECT_CMD_STS_FLAG);
78 if (val)
79 dev_dbg(d->dev, "DSI_DIRECT_CMD_STS_FLAG = %08x\n", val);
80 if (val & DSI_DIRECT_CMD_STS_WRITE_COMPLETED)
81 dev_dbg(d->dev, "direct command write completed\n");
82 if (val & DSI_DIRECT_CMD_STS_TE_RECEIVED) {
83 te_received = true;
84 dev_dbg(d->dev, "direct command TE received\n");
85 }
86 if (val & DSI_DIRECT_CMD_STS_ACKNOWLEDGE_WITH_ERR_RECEIVED)
87 dev_err(d->dev, "direct command ACK ERR received\n");
88 if (val & DSI_DIRECT_CMD_STS_READ_COMPLETED_WITH_ERR)
89 dev_err(d->dev, "direct command read ERR received\n");
90 /* Mask off the ACK value and clear status */
91 writel(val, d->regs + DSI_DIRECT_CMD_STS_CLR);
92
93 val = readl(d->regs + DSI_CMD_MODE_STS_FLAG);
94 if (val)
95 dev_dbg(d->dev, "DSI_CMD_MODE_STS_FLAG = %08x\n", val);
96 if (val & DSI_CMD_MODE_STS_ERR_NO_TE)
97 /* This happens all the time (safe to ignore) */
98 dev_dbg(d->dev, "CMD mode no TE\n");
99 if (val & DSI_CMD_MODE_STS_ERR_TE_MISS)
100 /* This happens all the time (safe to ignore) */
101 dev_dbg(d->dev, "CMD mode TE miss\n");
102 if (val & DSI_CMD_MODE_STS_ERR_SDI1_UNDERRUN)
103 dev_err(d->dev, "CMD mode SD1 underrun\n");
104 if (val & DSI_CMD_MODE_STS_ERR_SDI2_UNDERRUN)
105 dev_err(d->dev, "CMD mode SD2 underrun\n");
106 if (val & DSI_CMD_MODE_STS_ERR_UNWANTED_RD)
107 dev_err(d->dev, "CMD mode unwanted RD\n");
108 writel(val, d->regs + DSI_CMD_MODE_STS_CLR);
109
110 val = readl(d->regs + DSI_DIRECT_CMD_RD_STS_FLAG);
111 if (val)
112 dev_dbg(d->dev, "DSI_DIRECT_CMD_RD_STS_FLAG = %08x\n", val);
113 writel(val, d->regs + DSI_DIRECT_CMD_RD_STS_CLR);
114
115 val = readl(d->regs + DSI_TG_STS_FLAG);
116 if (val)
117 dev_dbg(d->dev, "DSI_TG_STS_FLAG = %08x\n", val);
118 writel(val, d->regs + DSI_TG_STS_CLR);
119
120 val = readl(d->regs + DSI_VID_MODE_STS_FLAG);
121 if (val)
122 dev_dbg(d->dev, "DSI_VID_MODE_STS_FLAG = %08x\n", val);
123 if (val & DSI_VID_MODE_STS_VSG_RUNNING)
124 dev_dbg(d->dev, "VID mode VSG running\n");
125 if (val & DSI_VID_MODE_STS_ERR_MISSING_DATA)
126 dev_err(d->dev, "VID mode missing data\n");
127 if (val & DSI_VID_MODE_STS_ERR_MISSING_HSYNC)
128 dev_err(d->dev, "VID mode missing HSYNC\n");
129 if (val & DSI_VID_MODE_STS_ERR_MISSING_VSYNC)
130 dev_err(d->dev, "VID mode missing VSYNC\n");
131 if (val & DSI_VID_MODE_STS_REG_ERR_SMALL_LENGTH)
132 dev_err(d->dev, "VID mode less bytes than expected between two HSYNC\n");
133 if (val & DSI_VID_MODE_STS_REG_ERR_SMALL_HEIGHT)
134 dev_err(d->dev, "VID mode less lines than expected between two VSYNC\n");
135 if (val & (DSI_VID_MODE_STS_ERR_BURSTWRITE |
136 DSI_VID_MODE_STS_ERR_LINEWRITE |
137 DSI_VID_MODE_STS_ERR_LONGREAD))
138 dev_err(d->dev, "VID mode read/write error\n");
139 if (val & DSI_VID_MODE_STS_ERR_VRS_WRONG_LENGTH)
140 dev_err(d->dev, "VID mode received packets differ from expected size\n");
141 if (val & DSI_VID_MODE_STS_VSG_RECOVERY)
142 dev_err(d->dev, "VID mode VSG in recovery mode\n");
143 writel(val, d->regs + DSI_VID_MODE_STS_CLR);
144
145 return te_received;
146 }
147
mcde_dsi_attach_to_mcde(struct mcde_dsi * d)148 static void mcde_dsi_attach_to_mcde(struct mcde_dsi *d)
149 {
150 d->mcde->mdsi = d->mdsi;
151
152 /*
153 * Select the way the DSI data flow is pushing to the display:
154 * currently we just support video or command mode depending
155 * on the type of display. Video mode defaults to using the
156 * formatter itself for synchronization (stateless video panel).
157 *
158 * FIXME: add flags to struct mipi_dsi_device .flags to indicate
159 * displays that require BTA (bus turn around) so we can handle
160 * such displays as well. Figure out how to properly handle
161 * single frame on-demand updates with DRM for command mode
162 * displays (MCDE_COMMAND_ONESHOT_FLOW).
163 */
164 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO)
165 d->mcde->flow_mode = MCDE_VIDEO_FORMATTER_FLOW;
166 else
167 d->mcde->flow_mode = MCDE_COMMAND_TE_FLOW;
168 }
169
mcde_dsi_host_attach(struct mipi_dsi_host * host,struct mipi_dsi_device * mdsi)170 static int mcde_dsi_host_attach(struct mipi_dsi_host *host,
171 struct mipi_dsi_device *mdsi)
172 {
173 struct mcde_dsi *d = host_to_mcde_dsi(host);
174
175 if (mdsi->lanes < 1 || mdsi->lanes > 2) {
176 DRM_ERROR("dsi device params invalid, 1 or 2 lanes supported\n");
177 return -EINVAL;
178 }
179
180 dev_info(d->dev, "attached DSI device with %d lanes\n", mdsi->lanes);
181 /* MIPI_DSI_FMT_RGB88 etc */
182 dev_info(d->dev, "format %08x, %dbpp\n", mdsi->format,
183 mipi_dsi_pixel_format_to_bpp(mdsi->format));
184 dev_info(d->dev, "mode flags: %08lx\n", mdsi->mode_flags);
185
186 d->mdsi = mdsi;
187 if (d->mcde)
188 mcde_dsi_attach_to_mcde(d);
189
190 return 0;
191 }
192
mcde_dsi_host_detach(struct mipi_dsi_host * host,struct mipi_dsi_device * mdsi)193 static int mcde_dsi_host_detach(struct mipi_dsi_host *host,
194 struct mipi_dsi_device *mdsi)
195 {
196 struct mcde_dsi *d = host_to_mcde_dsi(host);
197
198 d->mdsi = NULL;
199 if (d->mcde)
200 d->mcde->mdsi = NULL;
201
202 return 0;
203 }
204
205 #define MCDE_DSI_HOST_IS_READ(type) \
206 ((type == MIPI_DSI_GENERIC_READ_REQUEST_0_PARAM) || \
207 (type == MIPI_DSI_GENERIC_READ_REQUEST_1_PARAM) || \
208 (type == MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM) || \
209 (type == MIPI_DSI_DCS_READ))
210
mcde_dsi_execute_transfer(struct mcde_dsi * d,const struct mipi_dsi_msg * msg)211 static int mcde_dsi_execute_transfer(struct mcde_dsi *d,
212 const struct mipi_dsi_msg *msg)
213 {
214 const u32 loop_delay_us = 10; /* us */
215 u32 loop_counter;
216 size_t txlen = msg->tx_len;
217 size_t rxlen = msg->rx_len;
218 int i;
219 u32 val;
220 int ret;
221
222 writel(~0, d->regs + DSI_DIRECT_CMD_STS_CLR);
223 writel(~0, d->regs + DSI_CMD_MODE_STS_CLR);
224 /* Send command */
225 writel(1, d->regs + DSI_DIRECT_CMD_SEND);
226
227 loop_counter = 1000 * 1000 / loop_delay_us;
228 if (MCDE_DSI_HOST_IS_READ(msg->type)) {
229 /* Read command */
230 while (!(readl(d->regs + DSI_DIRECT_CMD_STS) &
231 (DSI_DIRECT_CMD_STS_READ_COMPLETED |
232 DSI_DIRECT_CMD_STS_READ_COMPLETED_WITH_ERR))
233 && --loop_counter)
234 usleep_range(loop_delay_us, (loop_delay_us * 3) / 2);
235 if (!loop_counter) {
236 dev_err(d->dev, "DSI read timeout!\n");
237 /* Set exit code and retry */
238 return -ETIME;
239 }
240 } else {
241 /* Writing only */
242 while (!(readl(d->regs + DSI_DIRECT_CMD_STS) &
243 DSI_DIRECT_CMD_STS_WRITE_COMPLETED)
244 && --loop_counter)
245 usleep_range(loop_delay_us, (loop_delay_us * 3) / 2);
246
247 if (!loop_counter) {
248 /* Set exit code and retry */
249 dev_err(d->dev, "DSI write timeout!\n");
250 return -ETIME;
251 }
252 }
253
254 val = readl(d->regs + DSI_DIRECT_CMD_STS);
255 if (val & DSI_DIRECT_CMD_STS_READ_COMPLETED_WITH_ERR) {
256 dev_err(d->dev, "read completed with error\n");
257 writel(1, d->regs + DSI_DIRECT_CMD_RD_INIT);
258 return -EIO;
259 }
260 if (val & DSI_DIRECT_CMD_STS_ACKNOWLEDGE_WITH_ERR_RECEIVED) {
261 val >>= DSI_DIRECT_CMD_STS_ACK_VAL_SHIFT;
262 dev_err(d->dev, "error during transmission: %04x\n",
263 val);
264 return -EIO;
265 }
266
267 if (!MCDE_DSI_HOST_IS_READ(msg->type)) {
268 /* Return number of bytes written */
269 ret = txlen;
270 } else {
271 /* OK this is a read command, get the response */
272 u32 rdsz;
273 u32 rddat;
274 u8 *rx = msg->rx_buf;
275
276 rdsz = readl(d->regs + DSI_DIRECT_CMD_RD_PROPERTY);
277 rdsz &= DSI_DIRECT_CMD_RD_PROPERTY_RD_SIZE_MASK;
278 rddat = readl(d->regs + DSI_DIRECT_CMD_RDDAT);
279 if (rdsz < rxlen) {
280 dev_err(d->dev, "read error, requested %zd got %d\n",
281 rxlen, rdsz);
282 return -EIO;
283 }
284 /* FIXME: read more than 4 bytes */
285 for (i = 0; i < 4 && i < rxlen; i++)
286 rx[i] = (rddat >> (i * 8)) & 0xff;
287 ret = rdsz;
288 }
289
290 /* Successful transmission */
291 return ret;
292 }
293
mcde_dsi_host_transfer(struct mipi_dsi_host * host,const struct mipi_dsi_msg * msg)294 static ssize_t mcde_dsi_host_transfer(struct mipi_dsi_host *host,
295 const struct mipi_dsi_msg *msg)
296 {
297 struct mcde_dsi *d = host_to_mcde_dsi(host);
298 const u8 *tx = msg->tx_buf;
299 size_t txlen = msg->tx_len;
300 size_t rxlen = msg->rx_len;
301 unsigned int retries = 0;
302 u32 val;
303 int ret;
304 int i;
305
306 if (txlen > 16) {
307 dev_err(d->dev,
308 "dunno how to write more than 16 bytes yet\n");
309 return -EIO;
310 }
311 if (rxlen > 4) {
312 dev_err(d->dev,
313 "dunno how to read more than 4 bytes yet\n");
314 return -EIO;
315 }
316
317 dev_dbg(d->dev,
318 "message to channel %d, write %zd bytes read %zd bytes\n",
319 msg->channel, txlen, rxlen);
320
321 /* Command "nature" */
322 if (MCDE_DSI_HOST_IS_READ(msg->type))
323 /* MCTL_MAIN_DATA_CTL already set up */
324 val = DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_NAT_READ;
325 else
326 val = DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_NAT_WRITE;
327 /*
328 * More than 2 bytes will not fit in a single packet, so it's
329 * time to set the "long not short" bit. One byte is used by
330 * the MIPI DCS command leaving just one byte for the payload
331 * in a short package.
332 */
333 if (mipi_dsi_packet_format_is_long(msg->type))
334 val |= DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_LONGNOTSHORT;
335 val |= 0 << DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_ID_SHIFT;
336 val |= txlen << DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_SIZE_SHIFT;
337 val |= DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_LP_EN;
338 val |= msg->type << DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_HEAD_SHIFT;
339 writel(val, d->regs + DSI_DIRECT_CMD_MAIN_SETTINGS);
340
341 /* MIPI DCS command is part of the data */
342 if (txlen > 0) {
343 val = 0;
344 for (i = 0; i < 4 && i < txlen; i++)
345 val |= tx[i] << (i * 8);
346 }
347 writel(val, d->regs + DSI_DIRECT_CMD_WRDAT0);
348 if (txlen > 4) {
349 val = 0;
350 for (i = 0; i < 4 && (i + 4) < txlen; i++)
351 val |= tx[i + 4] << (i * 8);
352 writel(val, d->regs + DSI_DIRECT_CMD_WRDAT1);
353 }
354 if (txlen > 8) {
355 val = 0;
356 for (i = 0; i < 4 && (i + 8) < txlen; i++)
357 val |= tx[i + 8] << (i * 8);
358 writel(val, d->regs + DSI_DIRECT_CMD_WRDAT2);
359 }
360 if (txlen > 12) {
361 val = 0;
362 for (i = 0; i < 4 && (i + 12) < txlen; i++)
363 val |= tx[i + 12] << (i * 8);
364 writel(val, d->regs + DSI_DIRECT_CMD_WRDAT3);
365 }
366
367 while (retries < 3) {
368 ret = mcde_dsi_execute_transfer(d, msg);
369 if (ret >= 0)
370 break;
371 retries++;
372 }
373 if (ret < 0 && retries)
374 dev_err(d->dev, "gave up after %d retries\n", retries);
375
376 /* Clear any errors */
377 writel(~0, d->regs + DSI_DIRECT_CMD_STS_CLR);
378 writel(~0, d->regs + DSI_CMD_MODE_STS_CLR);
379
380 return ret;
381 }
382
383 static const struct mipi_dsi_host_ops mcde_dsi_host_ops = {
384 .attach = mcde_dsi_host_attach,
385 .detach = mcde_dsi_host_detach,
386 .transfer = mcde_dsi_host_transfer,
387 };
388
389 /* This sends a direct (short) command to request TE */
mcde_dsi_te_request(struct mipi_dsi_device * mdsi)390 void mcde_dsi_te_request(struct mipi_dsi_device *mdsi)
391 {
392 struct mcde_dsi *d;
393 u32 val;
394
395 d = host_to_mcde_dsi(mdsi->host);
396
397 /* Command "nature" TE request */
398 val = DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_NAT_TE_REQ;
399 val |= 0 << DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_ID_SHIFT;
400 val |= 2 << DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_SIZE_SHIFT;
401 val |= DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_LP_EN;
402 val |= MIPI_DSI_GENERIC_SHORT_WRITE_1_PARAM <<
403 DSI_DIRECT_CMD_MAIN_SETTINGS_CMD_HEAD_SHIFT;
404 writel(val, d->regs + DSI_DIRECT_CMD_MAIN_SETTINGS);
405
406 /* Clear TE reveived and error status bits and enables them */
407 writel(DSI_DIRECT_CMD_STS_CLR_TE_RECEIVED_CLR |
408 DSI_DIRECT_CMD_STS_CLR_ACKNOWLEDGE_WITH_ERR_RECEIVED_CLR,
409 d->regs + DSI_DIRECT_CMD_STS_CLR);
410 val = readl(d->regs + DSI_DIRECT_CMD_STS_CTL);
411 val |= DSI_DIRECT_CMD_STS_CTL_TE_RECEIVED_EN;
412 val |= DSI_DIRECT_CMD_STS_CTL_ACKNOWLEDGE_WITH_ERR_EN;
413 writel(val, d->regs + DSI_DIRECT_CMD_STS_CTL);
414
415 /* Clear and enable no TE or TE missing status */
416 writel(DSI_CMD_MODE_STS_CLR_ERR_NO_TE_CLR |
417 DSI_CMD_MODE_STS_CLR_ERR_TE_MISS_CLR,
418 d->regs + DSI_CMD_MODE_STS_CLR);
419 val = readl(d->regs + DSI_CMD_MODE_STS_CTL);
420 val |= DSI_CMD_MODE_STS_CTL_ERR_NO_TE_EN;
421 val |= DSI_CMD_MODE_STS_CTL_ERR_TE_MISS_EN;
422 writel(val, d->regs + DSI_CMD_MODE_STS_CTL);
423
424 /* Send this TE request command */
425 writel(1, d->regs + DSI_DIRECT_CMD_SEND);
426 }
427
mcde_dsi_setup_video_mode(struct mcde_dsi * d,const struct drm_display_mode * mode)428 static void mcde_dsi_setup_video_mode(struct mcde_dsi *d,
429 const struct drm_display_mode *mode)
430 {
431 /* cpp, characters per pixel, number of bytes per pixel */
432 u8 cpp = mipi_dsi_pixel_format_to_bpp(d->mdsi->format) / 8;
433 u64 pclk;
434 u64 bpl;
435 int hfp;
436 int hbp;
437 int hsa;
438 u32 blkline_pck, line_duration;
439 u32 val;
440
441 val = 0;
442 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
443 val |= DSI_VID_MAIN_CTL_BURST_MODE;
444 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) {
445 val |= DSI_VID_MAIN_CTL_SYNC_PULSE_ACTIVE;
446 val |= DSI_VID_MAIN_CTL_SYNC_PULSE_HORIZONTAL;
447 }
448 /* RGB header and pixel mode */
449 switch (d->mdsi->format) {
450 case MIPI_DSI_FMT_RGB565:
451 val |= MIPI_DSI_PACKED_PIXEL_STREAM_16 <<
452 DSI_VID_MAIN_CTL_HEADER_SHIFT;
453 val |= DSI_VID_MAIN_CTL_VID_PIXEL_MODE_16BITS;
454 break;
455 case MIPI_DSI_FMT_RGB666_PACKED:
456 val |= MIPI_DSI_PACKED_PIXEL_STREAM_18 <<
457 DSI_VID_MAIN_CTL_HEADER_SHIFT;
458 val |= DSI_VID_MAIN_CTL_VID_PIXEL_MODE_18BITS;
459 break;
460 case MIPI_DSI_FMT_RGB666:
461 val |= MIPI_DSI_PIXEL_STREAM_3BYTE_18
462 << DSI_VID_MAIN_CTL_HEADER_SHIFT;
463 val |= DSI_VID_MAIN_CTL_VID_PIXEL_MODE_18BITS_LOOSE;
464 break;
465 case MIPI_DSI_FMT_RGB888:
466 val |= MIPI_DSI_PACKED_PIXEL_STREAM_24 <<
467 DSI_VID_MAIN_CTL_HEADER_SHIFT;
468 val |= DSI_VID_MAIN_CTL_VID_PIXEL_MODE_24BITS;
469 break;
470 default:
471 dev_err(d->dev, "unknown pixel mode\n");
472 return;
473 }
474
475 /* TODO: TVG (test video generator) could be enabled here */
476
477 /*
478 * During vertical blanking: go to LP mode
479 * Like with the EOL setting, if this is not set, the EOL area will be
480 * filled with NULL or blanking packets in the vblank area.
481 * FIXME: some Samsung phones and display panels such as s6e63m0 use
482 * DSI_VID_MAIN_CTL_REG_BLKLINE_MODE_BLANKING here instead,
483 * figure out how to properly configure that from the panel.
484 */
485 val |= DSI_VID_MAIN_CTL_REG_BLKLINE_MODE_LP_0;
486 /*
487 * During EOL: go to LP mode. If this is not set, the EOL area will be
488 * filled with NULL or blanking packets.
489 */
490 val |= DSI_VID_MAIN_CTL_REG_BLKEOL_MODE_LP_0;
491 /* Recovery mode 1 */
492 val |= 1 << DSI_VID_MAIN_CTL_RECOVERY_MODE_SHIFT;
493 /* All other fields zero */
494 writel(val, d->regs + DSI_VID_MAIN_CTL);
495
496 /* Vertical frame parameters are pretty straight-forward */
497 val = mode->vdisplay << DSI_VID_VSIZE_VACT_LENGTH_SHIFT;
498 /* vertical front porch */
499 val |= (mode->vsync_start - mode->vdisplay)
500 << DSI_VID_VSIZE_VFP_LENGTH_SHIFT;
501 /* vertical sync active */
502 val |= (mode->vsync_end - mode->vsync_start)
503 << DSI_VID_VSIZE_VSA_LENGTH_SHIFT;
504 /* vertical back porch */
505 val |= (mode->vtotal - mode->vsync_end)
506 << DSI_VID_VSIZE_VBP_LENGTH_SHIFT;
507 writel(val, d->regs + DSI_VID_VSIZE);
508
509 /*
510 * Horizontal frame parameters:
511 * horizontal resolution is given in pixels but must be re-calculated
512 * into bytes since this is what the hardware expects, these registers
513 * define the payload size of the packet.
514 *
515 * hfp = horizontal front porch in bytes
516 * hbp = horizontal back porch in bytes
517 * hsa = horizontal sync active in bytes
518 *
519 * 6 + 2 is HFP header + checksum
520 */
521 hfp = (mode->hsync_start - mode->hdisplay) * cpp - 6 - 2;
522 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) {
523 /*
524 * Use sync pulse for sync: explicit HSA time
525 * 6 is HBP header + checksum
526 * 4 is RGB header + checksum
527 */
528 hbp = (mode->htotal - mode->hsync_end) * cpp - 4 - 6;
529 /*
530 * 6 is HBP header + checksum
531 * 4 is HSW packet bytes
532 * 4 is RGB header + checksum
533 */
534 hsa = (mode->hsync_end - mode->hsync_start) * cpp - 4 - 4 - 6;
535 } else {
536 /*
537 * Use event for sync: HBP includes both back porch and sync
538 * 6 is HBP header + checksum
539 * 4 is HSW packet bytes
540 * 4 is RGB header + checksum
541 */
542 hbp = (mode->htotal - mode->hsync_start) * cpp - 4 - 4 - 6;
543 /* HSA is not present in this mode and set to 0 */
544 hsa = 0;
545 }
546 if (hfp < 0) {
547 dev_info(d->dev, "hfp negative, set to 0\n");
548 hfp = 0;
549 }
550 if (hbp < 0) {
551 dev_info(d->dev, "hbp negative, set to 0\n");
552 hbp = 0;
553 }
554 if (hsa < 0) {
555 dev_info(d->dev, "hsa negative, set to 0\n");
556 hsa = 0;
557 }
558 dev_dbg(d->dev, "hfp: %u, hbp: %u, hsa: %u bytes\n",
559 hfp, hbp, hsa);
560
561 /* Frame parameters: horizontal sync active */
562 val = hsa << DSI_VID_HSIZE1_HSA_LENGTH_SHIFT;
563 /* horizontal back porch */
564 val |= hbp << DSI_VID_HSIZE1_HBP_LENGTH_SHIFT;
565 /* horizontal front porch */
566 val |= hfp << DSI_VID_HSIZE1_HFP_LENGTH_SHIFT;
567 writel(val, d->regs + DSI_VID_HSIZE1);
568
569 /* RGB data length (visible bytes on one scanline) */
570 val = mode->hdisplay * cpp;
571 writel(val, d->regs + DSI_VID_HSIZE2);
572 dev_dbg(d->dev, "RGB length, visible area on a line: %u bytes\n", val);
573
574 /*
575 * Calculate the time between two pixels in picoseconds using
576 * the supplied refresh rate and total resolution including
577 * porches and sync.
578 */
579 /* (ps/s) / (pixels/s) = ps/pixels */
580 pclk = DIV_ROUND_UP_ULL(1000000000000, (mode->clock * 1000));
581 dev_dbg(d->dev, "picoseconds between two pixels: %llu\n",
582 pclk);
583
584 /*
585 * How many bytes per line will this update frequency yield?
586 *
587 * Calculate the number of picoseconds for one scanline (1), then
588 * divide by 1000000000000 (2) to get in pixels per second we
589 * want to output.
590 *
591 * Multiply with number of bytes per second at this video display
592 * frequency (3) to get number of bytes transferred during this
593 * time. Notice that we use the frequency the display wants,
594 * not what we actually get from the DSI PLL, which is hs_freq.
595 *
596 * These arithmetics are done in a different order to avoid
597 * overflow.
598 */
599 bpl = pclk * mode->htotal; /* (1) picoseconds per line */
600 dev_dbg(d->dev, "picoseconds per line: %llu\n", bpl);
601 /* Multiply with bytes per second (3) */
602 bpl *= (d->mdsi->hs_rate / 8);
603 /* Pixels per second (2) */
604 bpl = DIV_ROUND_DOWN_ULL(bpl, 1000000); /* microseconds */
605 bpl = DIV_ROUND_DOWN_ULL(bpl, 1000000); /* seconds */
606 /* parallel transactions in all lanes */
607 bpl *= d->mdsi->lanes;
608 dev_dbg(d->dev,
609 "calculated bytes per line: %llu @ %d Hz with HS %lu Hz\n",
610 bpl, drm_mode_vrefresh(mode), d->mdsi->hs_rate);
611
612 /*
613 * 6 is header + checksum, header = 4 bytes, checksum = 2 bytes
614 * 4 is short packet for vsync/hsync
615 */
616 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) {
617 /* Set the event packet size to 0 (not used) */
618 writel(0, d->regs + DSI_VID_BLKSIZE1);
619 /*
620 * FIXME: isn't the hsync width in pixels? The porch and
621 * sync area size is in pixels here, but this -6
622 * seems to be for bytes. It looks like this in the vendor
623 * code though. Is it completely untested?
624 */
625 blkline_pck = bpl - (mode->hsync_end - mode->hsync_start) - 6;
626 val = blkline_pck << DSI_VID_BLKSIZE2_BLKLINE_PULSE_PCK_SHIFT;
627 writel(val, d->regs + DSI_VID_BLKSIZE2);
628 } else {
629 /* Set the sync pulse packet size to 0 (not used) */
630 writel(0, d->regs + DSI_VID_BLKSIZE2);
631 /* Specifying payload size in bytes (-4-6 from manual) */
632 blkline_pck = bpl - 4 - 6;
633 if (blkline_pck > 0x1FFF)
634 dev_err(d->dev, "blkline_pck too big %d bytes\n",
635 blkline_pck);
636 val = blkline_pck << DSI_VID_BLKSIZE1_BLKLINE_EVENT_PCK_SHIFT;
637 val &= DSI_VID_BLKSIZE1_BLKLINE_EVENT_PCK_MASK;
638 writel(val, d->regs + DSI_VID_BLKSIZE1);
639 }
640
641 /*
642 * The line duration is used to scale back the frequency from
643 * the max frequency supported by the HS clock to the desired
644 * update frequency in vrefresh.
645 */
646 line_duration = blkline_pck + 6;
647 /*
648 * The datasheet contains this complex condition to decreasing
649 * the line duration by 1 under very specific circumstances.
650 * Here we also imply that LP is used during burst EOL.
651 */
652 if (d->mdsi->lanes == 2 && (hsa & 0x01) && (hfp & 0x01)
653 && (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST))
654 line_duration--;
655 line_duration = DIV_ROUND_CLOSEST(line_duration, d->mdsi->lanes);
656 dev_dbg(d->dev, "line duration %u bytes\n", line_duration);
657 val = line_duration << DSI_VID_DPHY_TIME_REG_LINE_DURATION_SHIFT;
658 /*
659 * This is the time to perform LP->HS on D-PHY
660 * FIXME: nowhere to get this from: DT property on the DSI?
661 * The manual says this is "system dependent".
662 * values like 48 and 72 seen in the vendor code.
663 */
664 val |= 48 << DSI_VID_DPHY_TIME_REG_WAKEUP_TIME_SHIFT;
665 writel(val, d->regs + DSI_VID_DPHY_TIME);
666
667 /*
668 * See the manual figure 657 page 2203 for understanding the impact
669 * of the different burst mode settings.
670 */
671 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) {
672 int blkeol_pck, blkeol_duration;
673 /*
674 * Packet size at EOL for burst mode, this is only used
675 * if DSI_VID_MAIN_CTL_REG_BLKEOL_MODE_LP_0 is NOT set,
676 * but we instead send NULL or blanking packets at EOL.
677 * This is given in number of bytes.
678 *
679 * See the manual page 2198 for the 13 reg_blkeol_pck bits.
680 */
681 blkeol_pck = bpl - (mode->htotal * cpp) - 6;
682 if (blkeol_pck < 0) {
683 dev_err(d->dev, "video block does not fit on line!\n");
684 dev_err(d->dev,
685 "calculated bytes per line: %llu @ %d Hz\n",
686 bpl, drm_mode_vrefresh(mode));
687 dev_err(d->dev,
688 "bytes per line (blkline_pck) %u bytes\n",
689 blkline_pck);
690 dev_err(d->dev,
691 "blkeol_pck becomes %d bytes\n", blkeol_pck);
692 return;
693 }
694 dev_dbg(d->dev, "BLKEOL packet: %d bytes\n", blkeol_pck);
695
696 val = readl(d->regs + DSI_VID_BLKSIZE1);
697 val &= ~DSI_VID_BLKSIZE1_BLKEOL_PCK_MASK;
698 val |= blkeol_pck << DSI_VID_BLKSIZE1_BLKEOL_PCK_SHIFT;
699 writel(val, d->regs + DSI_VID_BLKSIZE1);
700 /* Use the same value for exact burst limit */
701 val = blkeol_pck <<
702 DSI_VID_VCA_SETTING2_EXACT_BURST_LIMIT_SHIFT;
703 val &= DSI_VID_VCA_SETTING2_EXACT_BURST_LIMIT_MASK;
704 writel(val, d->regs + DSI_VID_VCA_SETTING2);
705 /*
706 * This BLKEOL duration is claimed to be the duration in clock
707 * cycles of the BLLP end-of-line (EOL) period for each line if
708 * DSI_VID_MAIN_CTL_REG_BLKEOL_MODE_LP_0 is set.
709 *
710 * It is hard to trust the manuals' claim that this is in clock
711 * cycles as we mimic the behaviour of the vendor code, which
712 * appears to write a number of bytes that would have been
713 * transferred on a single lane.
714 *
715 * See the manual figure 657 page 2203 and page 2198 for the 13
716 * reg_blkeol_duration bits.
717 *
718 * FIXME: should this also be set up also for non-burst mode
719 * according to figure 565 page 2202?
720 */
721 blkeol_duration = DIV_ROUND_CLOSEST(blkeol_pck + 6,
722 d->mdsi->lanes);
723 dev_dbg(d->dev, "BLKEOL duration: %d clock cycles\n",
724 blkeol_duration);
725
726 val = readl(d->regs + DSI_VID_PCK_TIME);
727 val &= ~DSI_VID_PCK_TIME_BLKEOL_DURATION_MASK;
728 val |= blkeol_duration <<
729 DSI_VID_PCK_TIME_BLKEOL_DURATION_SHIFT;
730 writel(val, d->regs + DSI_VID_PCK_TIME);
731
732 /* Max burst limit, this is given in bytes */
733 val = readl(d->regs + DSI_VID_VCA_SETTING1);
734 val &= ~DSI_VID_VCA_SETTING1_MAX_BURST_LIMIT_MASK;
735 val |= (blkeol_pck - 6) <<
736 DSI_VID_VCA_SETTING1_MAX_BURST_LIMIT_SHIFT;
737 writel(val, d->regs + DSI_VID_VCA_SETTING1);
738 }
739
740 /* Maximum line limit */
741 val = readl(d->regs + DSI_VID_VCA_SETTING2);
742 val &= ~DSI_VID_VCA_SETTING2_MAX_LINE_LIMIT_MASK;
743 val |= (blkline_pck - 6) <<
744 DSI_VID_VCA_SETTING2_MAX_LINE_LIMIT_SHIFT;
745 writel(val, d->regs + DSI_VID_VCA_SETTING2);
746 dev_dbg(d->dev, "blkline pck: %d bytes\n", blkline_pck - 6);
747 }
748
mcde_dsi_start(struct mcde_dsi * d)749 static void mcde_dsi_start(struct mcde_dsi *d)
750 {
751 unsigned long hs_freq;
752 u32 val;
753 int i;
754
755 /* No integration mode */
756 writel(0, d->regs + DSI_MCTL_INTEGRATION_MODE);
757
758 /* Enable the DSI port, from drivers/video/mcde/dsilink_v2.c */
759 val = DSI_MCTL_MAIN_DATA_CTL_LINK_EN |
760 DSI_MCTL_MAIN_DATA_CTL_BTA_EN |
761 DSI_MCTL_MAIN_DATA_CTL_READ_EN |
762 DSI_MCTL_MAIN_DATA_CTL_REG_TE_EN;
763 if (!(d->mdsi->mode_flags & MIPI_DSI_MODE_EOT_PACKET))
764 val |= DSI_MCTL_MAIN_DATA_CTL_HOST_EOT_GEN;
765 writel(val, d->regs + DSI_MCTL_MAIN_DATA_CTL);
766
767 /* Set a high command timeout, clear other fields */
768 val = 0x3ff << DSI_CMD_MODE_CTL_TE_TIMEOUT_SHIFT;
769 writel(val, d->regs + DSI_CMD_MODE_CTL);
770
771 /*
772 * UI_X4 is described as "unit interval times four"
773 * I guess since DSI packets are 4 bytes wide, one unit
774 * is one byte.
775 */
776 hs_freq = clk_get_rate(d->hs_clk);
777 hs_freq /= 1000000; /* MHz */
778 val = 4000 / hs_freq;
779 dev_dbg(d->dev, "UI value: %d\n", val);
780 val <<= DSI_MCTL_DPHY_STATIC_UI_X4_SHIFT;
781 val &= DSI_MCTL_DPHY_STATIC_UI_X4_MASK;
782 writel(val, d->regs + DSI_MCTL_DPHY_STATIC);
783
784 /*
785 * Enable clocking: 0x0f (something?) between each burst,
786 * enable the second lane if needed, enable continuous clock if
787 * needed, enable switch into ULPM (ultra-low power mode) on
788 * all the lines.
789 */
790 val = 0x0f << DSI_MCTL_MAIN_PHY_CTL_WAIT_BURST_TIME_SHIFT;
791 if (d->mdsi->lanes == 2)
792 val |= DSI_MCTL_MAIN_PHY_CTL_LANE2_EN;
793 if (!(d->mdsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS))
794 val |= DSI_MCTL_MAIN_PHY_CTL_CLK_CONTINUOUS;
795 val |= DSI_MCTL_MAIN_PHY_CTL_CLK_ULPM_EN |
796 DSI_MCTL_MAIN_PHY_CTL_DAT1_ULPM_EN |
797 DSI_MCTL_MAIN_PHY_CTL_DAT2_ULPM_EN;
798 writel(val, d->regs + DSI_MCTL_MAIN_PHY_CTL);
799
800 val = (1 << DSI_MCTL_ULPOUT_TIME_CKLANE_ULPOUT_TIME_SHIFT) |
801 (1 << DSI_MCTL_ULPOUT_TIME_DATA_ULPOUT_TIME_SHIFT);
802 writel(val, d->regs + DSI_MCTL_ULPOUT_TIME);
803
804 writel(DSI_DPHY_LANES_TRIM_DPHY_SPECS_90_81B_0_90,
805 d->regs + DSI_DPHY_LANES_TRIM);
806
807 /* High PHY timeout */
808 val = (0x0f << DSI_MCTL_DPHY_TIMEOUT_CLK_DIV_SHIFT) |
809 (0x3fff << DSI_MCTL_DPHY_TIMEOUT_HSTX_TO_VAL_SHIFT) |
810 (0x3fff << DSI_MCTL_DPHY_TIMEOUT_LPRX_TO_VAL_SHIFT);
811 writel(val, d->regs + DSI_MCTL_DPHY_TIMEOUT);
812
813 val = DSI_MCTL_MAIN_EN_PLL_START |
814 DSI_MCTL_MAIN_EN_CKLANE_EN |
815 DSI_MCTL_MAIN_EN_DAT1_EN |
816 DSI_MCTL_MAIN_EN_IF1_EN;
817 if (d->mdsi->lanes == 2)
818 val |= DSI_MCTL_MAIN_EN_DAT2_EN;
819 writel(val, d->regs + DSI_MCTL_MAIN_EN);
820
821 /* Wait for the PLL to lock and the clock and data lines to come up */
822 i = 0;
823 val = DSI_MCTL_MAIN_STS_PLL_LOCK |
824 DSI_MCTL_MAIN_STS_CLKLANE_READY |
825 DSI_MCTL_MAIN_STS_DAT1_READY;
826 if (d->mdsi->lanes == 2)
827 val |= DSI_MCTL_MAIN_STS_DAT2_READY;
828 while ((readl(d->regs + DSI_MCTL_MAIN_STS) & val) != val) {
829 /* Sleep for a millisecond */
830 usleep_range(1000, 1500);
831 if (i++ == 100) {
832 dev_warn(d->dev, "DSI lanes did not start up\n");
833 return;
834 }
835 }
836
837 /* TODO needed? */
838
839 /* Command mode, clear IF1 ID */
840 val = readl(d->regs + DSI_CMD_MODE_CTL);
841 /*
842 * If we enable low-power mode here,
843 * then display updates become really slow.
844 */
845 if (d->mdsi->mode_flags & MIPI_DSI_MODE_LPM)
846 val |= DSI_CMD_MODE_CTL_IF1_LP_EN;
847 val &= ~DSI_CMD_MODE_CTL_IF1_ID_MASK;
848 writel(val, d->regs + DSI_CMD_MODE_CTL);
849
850 /* Wait for DSI PHY to initialize */
851 usleep_range(100, 200);
852 dev_info(d->dev, "DSI link enabled\n");
853 }
854
855 /*
856 * Notice that this is called from inside the display controller
857 * and not from the bridge callbacks.
858 */
mcde_dsi_enable(struct drm_bridge * bridge)859 void mcde_dsi_enable(struct drm_bridge *bridge)
860 {
861 struct mcde_dsi *d = bridge_to_mcde_dsi(bridge);
862 unsigned long hs_freq, lp_freq;
863 u32 val;
864 int ret;
865
866 /* Copy maximum clock frequencies */
867 if (d->mdsi->lp_rate)
868 lp_freq = d->mdsi->lp_rate;
869 else
870 lp_freq = DSI_DEFAULT_LP_FREQ_HZ;
871 if (d->mdsi->hs_rate)
872 hs_freq = d->mdsi->hs_rate;
873 else
874 hs_freq = DSI_DEFAULT_HS_FREQ_HZ;
875
876 /* Enable LP (Low Power, Energy Save, ES) and HS (High Speed) clocks */
877 d->lp_freq = clk_round_rate(d->lp_clk, lp_freq);
878 ret = clk_set_rate(d->lp_clk, d->lp_freq);
879 if (ret)
880 dev_err(d->dev, "failed to set LP clock rate %lu Hz\n",
881 d->lp_freq);
882
883 d->hs_freq = clk_round_rate(d->hs_clk, hs_freq);
884 ret = clk_set_rate(d->hs_clk, d->hs_freq);
885 if (ret)
886 dev_err(d->dev, "failed to set HS clock rate %lu Hz\n",
887 d->hs_freq);
888
889 /* Start clocks */
890 ret = clk_prepare_enable(d->lp_clk);
891 if (ret)
892 dev_err(d->dev, "failed to enable LP clock\n");
893 else
894 dev_info(d->dev, "DSI LP clock rate %lu Hz\n",
895 d->lp_freq);
896 ret = clk_prepare_enable(d->hs_clk);
897 if (ret)
898 dev_err(d->dev, "failed to enable HS clock\n");
899 else
900 dev_info(d->dev, "DSI HS clock rate %lu Hz\n",
901 d->hs_freq);
902
903 /* Assert RESET through the PRCMU, active low */
904 /* FIXME: which DSI block? */
905 regmap_update_bits(d->prcmu, PRCM_DSI_SW_RESET,
906 PRCM_DSI_SW_RESET_DSI0_SW_RESETN, 0);
907
908 usleep_range(100, 200);
909
910 /* De-assert RESET again */
911 regmap_update_bits(d->prcmu, PRCM_DSI_SW_RESET,
912 PRCM_DSI_SW_RESET_DSI0_SW_RESETN,
913 PRCM_DSI_SW_RESET_DSI0_SW_RESETN);
914
915 /* Start up the hardware */
916 mcde_dsi_start(d);
917
918 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
919 /* Set up the video mode from the DRM mode */
920 mcde_dsi_setup_video_mode(d, d->mode);
921
922 /* Put IF1 into video mode */
923 val = readl(d->regs + DSI_MCTL_MAIN_DATA_CTL);
924 val |= DSI_MCTL_MAIN_DATA_CTL_IF1_MODE;
925 writel(val, d->regs + DSI_MCTL_MAIN_DATA_CTL);
926
927 /* Disable command mode on IF1 */
928 val = readl(d->regs + DSI_CMD_MODE_CTL);
929 val &= ~DSI_CMD_MODE_CTL_IF1_LP_EN;
930 writel(val, d->regs + DSI_CMD_MODE_CTL);
931
932 /* Enable some error interrupts */
933 val = readl(d->regs + DSI_VID_MODE_STS_CTL);
934 val |= DSI_VID_MODE_STS_CTL_ERR_MISSING_VSYNC;
935 val |= DSI_VID_MODE_STS_CTL_ERR_MISSING_DATA;
936 writel(val, d->regs + DSI_VID_MODE_STS_CTL);
937
938 /* Enable video mode */
939 val = readl(d->regs + DSI_MCTL_MAIN_DATA_CTL);
940 val |= DSI_MCTL_MAIN_DATA_CTL_VID_EN;
941 writel(val, d->regs + DSI_MCTL_MAIN_DATA_CTL);
942 } else {
943 /* Command mode, clear IF1 ID */
944 val = readl(d->regs + DSI_CMD_MODE_CTL);
945 /*
946 * If we enable low-power mode here
947 * the display updates become really slow.
948 */
949 if (d->mdsi->mode_flags & MIPI_DSI_MODE_LPM)
950 val |= DSI_CMD_MODE_CTL_IF1_LP_EN;
951 val &= ~DSI_CMD_MODE_CTL_IF1_ID_MASK;
952 writel(val, d->regs + DSI_CMD_MODE_CTL);
953 }
954
955 dev_info(d->dev, "enabled MCDE DSI master\n");
956 }
957
mcde_dsi_bridge_mode_set(struct drm_bridge * bridge,const struct drm_display_mode * mode,const struct drm_display_mode * adj)958 static void mcde_dsi_bridge_mode_set(struct drm_bridge *bridge,
959 const struct drm_display_mode *mode,
960 const struct drm_display_mode *adj)
961 {
962 struct mcde_dsi *d = bridge_to_mcde_dsi(bridge);
963
964 if (!d->mdsi) {
965 dev_err(d->dev, "no DSI device attached to encoder!\n");
966 return;
967 }
968
969 d->mode = mode;
970
971 dev_info(d->dev, "set DSI master to %dx%d %u Hz %s mode\n",
972 mode->hdisplay, mode->vdisplay, mode->clock * 1000,
973 (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO) ? "VIDEO" : "CMD"
974 );
975 }
976
mcde_dsi_wait_for_command_mode_stop(struct mcde_dsi * d)977 static void mcde_dsi_wait_for_command_mode_stop(struct mcde_dsi *d)
978 {
979 u32 val;
980 int i;
981
982 /*
983 * Wait until we get out of command mode
984 * CSM = Command State Machine
985 */
986 i = 0;
987 val = DSI_CMD_MODE_STS_CSM_RUNNING;
988 while ((readl(d->regs + DSI_CMD_MODE_STS) & val) == val) {
989 /* Sleep for a millisecond */
990 usleep_range(1000, 2000);
991 if (i++ == 100) {
992 dev_warn(d->dev,
993 "could not get out of command mode\n");
994 return;
995 }
996 }
997 }
998
mcde_dsi_wait_for_video_mode_stop(struct mcde_dsi * d)999 static void mcde_dsi_wait_for_video_mode_stop(struct mcde_dsi *d)
1000 {
1001 u32 val;
1002 int i;
1003
1004 /* Wait until we get out og video mode */
1005 i = 0;
1006 val = DSI_VID_MODE_STS_VSG_RUNNING;
1007 while ((readl(d->regs + DSI_VID_MODE_STS) & val) == val) {
1008 /* Sleep for a millisecond */
1009 usleep_range(1000, 2000);
1010 if (i++ == 100) {
1011 dev_warn(d->dev,
1012 "could not get out of video mode\n");
1013 return;
1014 }
1015 }
1016 }
1017
1018 /*
1019 * Notice that this is called from inside the display controller
1020 * and not from the bridge callbacks.
1021 */
mcde_dsi_disable(struct drm_bridge * bridge)1022 void mcde_dsi_disable(struct drm_bridge *bridge)
1023 {
1024 struct mcde_dsi *d = bridge_to_mcde_dsi(bridge);
1025 u32 val;
1026
1027 if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
1028 /* Stop video mode */
1029 val = readl(d->regs + DSI_MCTL_MAIN_DATA_CTL);
1030 val &= ~DSI_MCTL_MAIN_DATA_CTL_VID_EN;
1031 writel(val, d->regs + DSI_MCTL_MAIN_DATA_CTL);
1032 mcde_dsi_wait_for_video_mode_stop(d);
1033 } else {
1034 /* Stop command mode */
1035 mcde_dsi_wait_for_command_mode_stop(d);
1036 }
1037
1038 /*
1039 * Stop clocks and terminate any DSI traffic here so the panel can
1040 * send commands to shut down the display using DSI direct write until
1041 * this point.
1042 */
1043
1044 /* Disable all error interrupts */
1045 writel(0, d->regs + DSI_VID_MODE_STS_CTL);
1046 clk_disable_unprepare(d->hs_clk);
1047 clk_disable_unprepare(d->lp_clk);
1048 }
1049
mcde_dsi_bridge_attach(struct drm_bridge * bridge,enum drm_bridge_attach_flags flags)1050 static int mcde_dsi_bridge_attach(struct drm_bridge *bridge,
1051 enum drm_bridge_attach_flags flags)
1052 {
1053 struct mcde_dsi *d = bridge_to_mcde_dsi(bridge);
1054 struct drm_device *drm = bridge->dev;
1055 int ret;
1056
1057 if (!drm_core_check_feature(drm, DRIVER_ATOMIC)) {
1058 dev_err(d->dev, "we need atomic updates\n");
1059 return -ENOTSUPP;
1060 }
1061
1062 /* Attach the DSI bridge to the output (panel etc) bridge */
1063 ret = drm_bridge_attach(bridge->encoder, d->bridge_out, bridge, flags);
1064 if (ret) {
1065 dev_err(d->dev, "failed to attach the DSI bridge\n");
1066 return ret;
1067 }
1068
1069 return 0;
1070 }
1071
1072 static const struct drm_bridge_funcs mcde_dsi_bridge_funcs = {
1073 .attach = mcde_dsi_bridge_attach,
1074 .mode_set = mcde_dsi_bridge_mode_set,
1075 };
1076
mcde_dsi_bind(struct device * dev,struct device * master,void * data)1077 static int mcde_dsi_bind(struct device *dev, struct device *master,
1078 void *data)
1079 {
1080 struct drm_device *drm = data;
1081 struct mcde *mcde = to_mcde(drm);
1082 struct mcde_dsi *d = dev_get_drvdata(dev);
1083 struct device_node *child;
1084 struct drm_panel *panel = NULL;
1085 struct drm_bridge *bridge = NULL;
1086
1087 if (!of_get_available_child_count(dev->of_node)) {
1088 dev_info(dev, "unused DSI interface\n");
1089 d->unused = true;
1090 return 0;
1091 }
1092 d->mcde = mcde;
1093 /* If the display attached before binding, set this up */
1094 if (d->mdsi)
1095 mcde_dsi_attach_to_mcde(d);
1096
1097 /* Obtain the clocks */
1098 d->hs_clk = devm_clk_get(dev, "hs");
1099 if (IS_ERR(d->hs_clk)) {
1100 dev_err(dev, "unable to get HS clock\n");
1101 return PTR_ERR(d->hs_clk);
1102 }
1103
1104 d->lp_clk = devm_clk_get(dev, "lp");
1105 if (IS_ERR(d->lp_clk)) {
1106 dev_err(dev, "unable to get LP clock\n");
1107 return PTR_ERR(d->lp_clk);
1108 }
1109
1110 /* Look for a panel as a child to this node */
1111 for_each_available_child_of_node(dev->of_node, child) {
1112 panel = of_drm_find_panel(child);
1113 if (IS_ERR(panel)) {
1114 dev_err(dev, "failed to find panel try bridge (%ld)\n",
1115 PTR_ERR(panel));
1116 panel = NULL;
1117
1118 bridge = of_drm_find_bridge(child);
1119 if (!bridge) {
1120 dev_err(dev, "failed to find bridge\n");
1121 of_node_put(child);
1122 return -EINVAL;
1123 }
1124 }
1125 }
1126 if (panel) {
1127 bridge = drm_panel_bridge_add_typed(panel,
1128 DRM_MODE_CONNECTOR_DSI);
1129 if (IS_ERR(bridge)) {
1130 dev_err(dev, "error adding panel bridge\n");
1131 return PTR_ERR(bridge);
1132 }
1133 dev_info(dev, "connected to panel\n");
1134 d->panel = panel;
1135 } else if (bridge) {
1136 /* TODO: AV8100 HDMI encoder goes here for example */
1137 dev_info(dev, "connected to non-panel bridge (unsupported)\n");
1138 return -ENODEV;
1139 } else {
1140 dev_err(dev, "no panel or bridge\n");
1141 return -ENODEV;
1142 }
1143
1144 d->bridge_out = bridge;
1145
1146 /* Create a bridge for this DSI channel */
1147 d->bridge.funcs = &mcde_dsi_bridge_funcs;
1148 d->bridge.of_node = dev->of_node;
1149 drm_bridge_add(&d->bridge);
1150
1151 /* TODO: first come first serve, use a list */
1152 mcde->bridge = &d->bridge;
1153
1154 dev_info(dev, "initialized MCDE DSI bridge\n");
1155
1156 return 0;
1157 }
1158
mcde_dsi_unbind(struct device * dev,struct device * master,void * data)1159 static void mcde_dsi_unbind(struct device *dev, struct device *master,
1160 void *data)
1161 {
1162 struct mcde_dsi *d = dev_get_drvdata(dev);
1163
1164 if (d->panel)
1165 drm_panel_bridge_remove(d->bridge_out);
1166 regmap_update_bits(d->prcmu, PRCM_DSI_SW_RESET,
1167 PRCM_DSI_SW_RESET_DSI0_SW_RESETN, 0);
1168 }
1169
1170 static const struct component_ops mcde_dsi_component_ops = {
1171 .bind = mcde_dsi_bind,
1172 .unbind = mcde_dsi_unbind,
1173 };
1174
mcde_dsi_probe(struct platform_device * pdev)1175 static int mcde_dsi_probe(struct platform_device *pdev)
1176 {
1177 struct device *dev = &pdev->dev;
1178 struct mcde_dsi *d;
1179 struct mipi_dsi_host *host;
1180 struct resource *res;
1181 u32 dsi_id;
1182 int ret;
1183
1184 d = devm_kzalloc(dev, sizeof(*d), GFP_KERNEL);
1185 if (!d)
1186 return -ENOMEM;
1187 d->dev = dev;
1188 platform_set_drvdata(pdev, d);
1189
1190 /* Get a handle on the PRCMU so we can do reset */
1191 d->prcmu =
1192 syscon_regmap_lookup_by_compatible("stericsson,db8500-prcmu");
1193 if (IS_ERR(d->prcmu)) {
1194 dev_err(dev, "no PRCMU regmap\n");
1195 return PTR_ERR(d->prcmu);
1196 }
1197
1198 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1199 d->regs = devm_ioremap_resource(dev, res);
1200 if (IS_ERR(d->regs)) {
1201 dev_err(dev, "no DSI regs\n");
1202 return PTR_ERR(d->regs);
1203 }
1204
1205 dsi_id = readl(d->regs + DSI_ID_REG);
1206 dev_info(dev, "HW revision 0x%08x\n", dsi_id);
1207
1208 host = &d->dsi_host;
1209 host->dev = dev;
1210 host->ops = &mcde_dsi_host_ops;
1211 ret = mipi_dsi_host_register(host);
1212 if (ret < 0) {
1213 dev_err(dev, "failed to register DSI host: %d\n", ret);
1214 return ret;
1215 }
1216 dev_info(dev, "registered DSI host\n");
1217
1218 platform_set_drvdata(pdev, d);
1219 return component_add(dev, &mcde_dsi_component_ops);
1220 }
1221
mcde_dsi_remove(struct platform_device * pdev)1222 static int mcde_dsi_remove(struct platform_device *pdev)
1223 {
1224 struct mcde_dsi *d = platform_get_drvdata(pdev);
1225
1226 component_del(&pdev->dev, &mcde_dsi_component_ops);
1227 mipi_dsi_host_unregister(&d->dsi_host);
1228
1229 return 0;
1230 }
1231
1232 static const struct of_device_id mcde_dsi_of_match[] = {
1233 {
1234 .compatible = "ste,mcde-dsi",
1235 },
1236 {},
1237 };
1238
1239 struct platform_driver mcde_dsi_driver = {
1240 .driver = {
1241 .name = "mcde-dsi",
1242 .of_match_table = of_match_ptr(mcde_dsi_of_match),
1243 },
1244 .probe = mcde_dsi_probe,
1245 .remove = mcde_dsi_remove,
1246 };
1247