Searched +full:0 +full:x28 (Results 1 – 25 of 69) sorted by relevance
123
| /Documentation/devicetree/bindings/arm/freescale/ |
| D | tigerp.txt | 11 reg = <0x83fa0000 0x28>;
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | ad741x.txt | 14 reg = <0x28>;
|
| /Documentation/devicetree/bindings/rng/ |
| D | brcm,iproc-rng200.txt | 15 reg = <0x18032000 0x28>;
|
| /Documentation/devicetree/bindings/watchdog/ |
| D | brcm,bcm2835-pm-wdog.txt | 16 reg = <0x7e100000 0x28>;
|
| /Documentation/devicetree/bindings/phy/ |
| D | brcm,kona-usb2-phy.txt | 6 - #phy-cells: must be 0
13 reg = <0x3f130000 0x28>;
14 #phy-cells = <0>;
|
| D | intel,lgm-usb-phy.yaml | 35 const: 0
51 reg = <0xe7e00000 0x10000>;
53 resets = <&rcu 0x70 0x24>,
54 <&rcu 0x70 0x26>,
55 <&rcu 0x70 0x28>;
57 #phy-cells = <0>;
|
| /Documentation/hwmon/ |
| D | lm80.rst | 10 Addresses scanned: I2C 0x28 - 0x2f
20 Addresses scanned: I2C 0x28 - 0x2f
63 inputs can measure voltages between 0 and 2.55 volts, with a resolution
|
| D | lm78.rst | 10 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
20 Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
64 inputs can measure voltages between 0 and 4.08 volts, with a resolution
|
| /Documentation/devicetree/bindings/sound/ |
| D | rt1015.txt | 21 reg = <0x28>;
|
| /Documentation/devicetree/bindings/iio/potentiometer/ |
| D | ds1803.txt | 19 reg = <0x28>;
|
| D | max5432.yaml | 39 #size-cells = <0>;
42 reg = <0x28>;
|
| /Documentation/devicetree/bindings/spi/ |
| D | spi-sc18is602.txt | 21 reg = <0x28>;
|
| D | spi-orion.txt | 19 chip-select lines 0 through 7 respectively.
37 #size-cells = <0>;
38 cell-index = <0>;
39 reg = <0x10600 0x28>;
47 #size-cells = <0>;
48 cell-index = <0>;
49 reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */
50 <MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */
51 <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */
52 <MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */
[all …]
|
| /Documentation/devicetree/bindings/pwm/ |
| D | brcm,bcm7038-pwm.txt | 17 reg = <0xf0408000 0x28>;
|
| D | brcm,iproc-pwm.txt | 18 reg = <0x18031000 0x28>;
|
| D | pwm-bcm2835.txt | 16 reg = <0x2020c000 0x28>;
26 #clock-cells = <0>;
|
| /Documentation/devicetree/bindings/timer/ |
| D | via,vt8500-timer.txt | 13 reg = <0xd8130100 0x28>;
|
| /Documentation/devicetree/bindings/i2c/ |
| D | renesas,iic-emev2.txt | 10 - #size-cells : should be <0>
16 #size-cells = <0>;
18 reg = <0xe0070000 0x28>;
19 interrupts = <0 32 IRQ_TYPE_EDGE_RISING>;
|
| /Documentation/devicetree/bindings/iio/proximity/ |
| D | sx9500.txt | 19 reg = <0x28>;
|
| /Documentation/devicetree/bindings/thermal/ |
| D | brcm,avs-tmon.txt | 19 reg = <0xf04d1500 0x28>;
20 interrupts = <0x6>;
|
| D | st-thermal.txt | 27 reg = <0x91a0000 0x28>;
|
| /Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ |
| D | ucc.txt | 15 - port-number : for UART drivers, the port number to use, between 0 and 3.
16 This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
36 0x00 : clock source is disabled;
37 0x1~0x10 : clock source is BRG1~BRG16 respectively;
38 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
40 0x00 : clock source is disabled;
41 0x1~0x10 : clock source is BRG1~BRG16 respectively;
42 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
60 interrupts = <a0 0>;
|
| /Documentation/devicetree/bindings/net/nfc/ |
| D | pn544.txt | 13 - pintctrl-0: Specifies the pin control groups used for this controller.
24 reg = <0x28>;
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio-ts4900.txt | 25 reg = <0x28>;
|
| /Documentation/devicetree/bindings/nvmem/ |
| D | uniphier-efuse.txt | 20 ranges = <0x0 0x5f900000 0x2000>;
24 reg = <0x100 0x28>;
29 reg = <0x200 0x68>;
35 reg = <0x54 0xc>;
|
123