Searched full:127 (Results 1 – 25 of 86) sorted by relevance
1234
| /Documentation/ABI/testing/ |
| D | sysfs-class-rtc-rtc0-device-rtc_calibration | 11 The range of the attribute is -127 to +127 in units of
|
| D | sysfs-class-backlight-driver-adp8870 | 15 on this <backlight>. Values are between 0 and 127. This file
29 on this <backlight>. Values are between 0 and 127, typically
|
| D | sysfs-class-backlight-adp5520 | 17 is an input code between 0 and 127, which is transformed to a
30 input code between 0 and 127, which is transformed to a value
|
| D | sysfs-class-backlight-adp8860 | 22 is an input code between 0 and 127, which is transformed to a
36 input code between 0 and 127, which is transformed to a value
|
| D | sysfs-bus-usb-lvstest | 18 and 127. It is needed for TD.7.18, TD.7.19, TD.7.20 and TD.7.21.
26 and 127. It is needed for TD.7.18, TD.7.19, TD.7.20 and TD.7.21.
|
| D | sysfs-driver-wacom | 28 Writing to this file sets the status LED luminance (1..127)
38 Writing to this file sets the status LED luminance (1..127)
|
| /Documentation/hwmon/ |
| D | lm95245.rst | 34 is given within a range of -127 to +127.875 degrees. Remote temperatures are
35 given within a range of -127 to +255 degrees. Resolution depends on
|
| D | w83773g.rst | 28 range of -40 to +125 degrees Celsius (for local sensor) and -40 to +127
|
| D | dme1737.rst | 147 temp1: Remote diode 1 (3904 type) temperature -127C - +127C
148 temp2: DME1737 internal temperature -127C - +127C
149 temp3: Remote diode 2 (3904 type) temperature -127C - +127C
|
| D | lm95234.rst | 37 is provided within a range of -127 to +255 degrees (+127.875 degrees for
|
| D | asb100.rst | 63 .. [1] This alarm will only trigger if the hysteresis value is 127C.
|
| /Documentation/driver-api/serial/ |
| D | n_gsm.rst | 60 /* our modem defaults to a maximum size of 127 bytes */
61 c.mru = 127;
62 c.mtu = 127;
|
| /Documentation/admin-guide/ |
| D | cputopology.rst | 170 kernel_max: 127
171 offline: 2,4-127,128-143
173 possible: 0-127
|
| /Documentation/devicetree/bindings/dma/ |
| D | dma-controller.yaml | 33 dma-requests = <127>;
|
| /Documentation/trace/ |
| D | stm.rst | 24 48 to 63 and channels 0 to 127.
45 0 127
49 through 127 in it. Now, any producer (trace source) identifying itself
|
| /Documentation/arm64/ |
| D | sve.rst | 70 values, with bits [(127 - 8 * i) : (120 - 8 * i)] of the register encoded at
97 * On syscall, V0..V31 are preserved (as without SVE). Thus, bits [127:0] of
162 data. However, for backward compatibility reasons, bits [127:0] of Z0..Z31
238 Z0..Z31 except for Z0 bits [127:0] .. Z31 bits [127:0] to become
421 For each Zn, Zn bits [127:0] alias the ARMv8-A vector register Vn.
424 Zn except for bits [127:0].
506 127 0 bit index
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | ti,c64x+megamod-pic.txt | 61 position. Allowed values are 4 - 127. Mapping for
67 Single cell specifying the megamodule interrupt source (4-127). Note that
|
| /Documentation/devicetree/bindings/pci/ |
| D | fsl,imx6q-pcie.txt | 25 - fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127
26 - fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127
|
| /Documentation/devicetree/bindings/mfd/ |
| D | ene-kb3930.yaml | 51 <&gpio 127 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-pwm.txt | 42 max-brightness = <127>;
|
| /Documentation/userspace-api/media/v4l/ |
| D | pixfmt-tch-td08.rst | 18 Delta values may range from -128 to 127. Typically the values will vary through
|
| D | dev-radio.rst | 14 ``/dev/radio63`` with major number 81 and minor numbers 64 to 127.
|
| /Documentation/devicetree/bindings/bus/ |
| D | brcm,bus-axi.txt | 41 <0x00012000 1 &gic GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
|
| D | baikal,bt1-axi.yaml | 99 interrupts = <GIC_SHARED 127 IRQ_TYPE_LEVEL_HIGH>;
|
| /Documentation/devicetree/bindings/sound/ |
| D | marvell,mmp-sspa.yaml | 107 clocks = <&soc_clocks 127>,
|
1234