Searched full:achieve (Results 1 – 25 of 94) sorted by relevance
1234
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-trigger-sysfs | 28 In order to achieve this, one should write a positive integer
39 achieve this, one should write a positive integer into the
|
| D | sysfs-class-backlight | 10 non-linear. To achieve a linear perception of brightness changes
|
| /Documentation/devicetree/bindings/arm/freescale/ |
| D | fsl,imx7ulp-pm.yaml | 16 controlling the power, clocks, and memories of the MCU to achieve the
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-class-multicolor.yaml | 15 etc.) or standalone LEDs, to achieve logically grouped multi-color LED
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | gpio-fan.txt | 10 control value that should be set to achieve them. This array
|
| /Documentation/userspace-api/media/mediactl/ |
| D | media-controller-model.rst | 9 is one of the goals of the media controller API. To achieve this,
|
| /Documentation/userspace-api/media/v4l/ |
| D | vidioc-g-parm.rst | 41 repeat frames to achieve the requested frame interval.
114 choose to skip or repeat frames in order to achieve the requested
239 driver writer may achieve that; it will depend on the hardware and
|
| /Documentation/devicetree/bindings/pwm/ |
| D | pwm-sifive.yaml | 19 the values it can achieve, which the driver rounds to the nearest
|
| D | nvidia,tegra20-pwm.txt | 52 Following will be DT binding to achieve this:
|
| /Documentation/block/ |
| D | bfq-iosched.rst | 19 goal, for a given device, is to achieve the maximum-possible
213 achieve this goal is to give to the queues associated with these
232 that it enables BFQ to achieve a high throughput, by queue
235 unified mechanism to achieve a high throughput with interleaved
456 DISABLE this mode if your only goal is to achieve a high throughput.
458 entail a lower throughput. To achieve the highest-possible throughput
492 it with auto-tuning. An alternative way to achieve this goal is to
|
| D | blk-mq.rst | 8 devices to achieve a huge number of input/output operations per second (IOPS)
19 development of the kernel. The Block IO subsystem aimed to achieve the best
|
| /Documentation/admin-guide/pm/ |
| D | cpufreq_drivers.rst | 121 OS wants for a logical processor. The platform firmware attempts to achieve
223 frequencies need to be listed because the BIOS will try to achieve any
237 conditions are met the BIOS can achieve a slightly higher speed than requested
|
| /Documentation/ide/ |
| D | ide-tape.rst | 67 a method by which we can achieve higher throughput when
|
| /Documentation/sound/soc/ |
| D | overview.rst | 53 To achieve all this, ASoC basically splits an embedded audio system into
|
| /Documentation/devicetree/bindings/regulator/ |
| D | gpio-regulator.yaml | 57 regulator and matching GPIO configurations to achieve them. If there are
|
| /Documentation/i2c/ |
| D | summary.rst | 21 achieve I2C branding. Modern PC mainboards rely on SMBus. The most common
|
| /Documentation/virt/kvm/arm/ |
| D | hyp-abi.rst | 23 In order to achieve this, the kernel must be booted at HYP (arm) or
|
| /Documentation/admin-guide/media/ |
| D | vimc.rst | 13 recompile the driver to achieve your own topology. This is the default topology:
|
| /Documentation/networking/device_drivers/cellular/qualcomm/ |
| D | rmnet.rst | 23 Aggregation is required to achieve high data rates. This involves hardware
|
| /Documentation/leds/ |
| D | leds-class-multicolor.rst | 50 for each LED that are necessary to achieve a certain color output from a
|
| /Documentation/driver-api/driver-model/ |
| D | design-patterns.rst | 21 The most common way to achieve this is to use the state container design
|
| /Documentation/locking/ |
| D | hwspinlock.rst | 26 To achieve fast message-based communications, a minimal kernel support
48 before it can be used to achieve synchronization.
309 hwspinlock is dynamically assigned: before it can be used to achieve
|
| /Documentation/timers/ |
| D | timers-howto.rst | 23 and will busy wait for enough loop cycles to achieve
|
| /Documentation/driver-api/memory-devices/ |
| D | ti-gpmc.rst | 29 generic timing routine was developed to achieve above requirements.
|
| /Documentation/bpf/ |
| D | ringbuf.rst | 81 - but still the ability to do busy polling for new data to achieve the
201 this allows to achieve a very high throughput without having to resort to
|
1234