Searched full:assumed (Results 1 – 25 of 165) sorted by relevance
1234567
| /Documentation/devicetree/bindings/display/panel/ |
| D | sharp,lq150x1lg11.yaml | 27 the RL/UD and/or SELLVDS pins are assumed to be handled
35 the RL/UD and/or SELLVDS pins are assumed to be handled
|
| /Documentation/devicetree/bindings/sound/ |
| D | adi,adau7002.txt | 12 If this property is not present it is assumed that the supply pin is
|
| D | tscs454.txt | 13 Note: If clock is not provided then bit clock is assumed
|
| D | ssm2518.txt | 12 assumed that the nSD pin is hardwired to always on.
|
| D | everest,es7241.txt | 16 If this property is not provided, sdout is assumed to pulled
|
| D | qcom,msm8916-wcd-analog.txt | 44 its assumed that hphl pin on jack is NC
48 its assumed that gnd pin on jack is NC
|
| D | pcm512x.txt | 27 external connection from the pll-out pin to the SCLK pin is assumed.
|
| /Documentation/userspace-api/media/v4l/ |
| D | selection-api-examples.rst | 7 (A video capture device is assumed; change
57 A video output device is assumed; change ``V4L2_BUF_TYPE_VIDEO_OUTPUT``
|
| /Documentation/devicetree/bindings/net/ |
| D | lpc-eth.txt | 10 absent, "rmii" is assumed.
|
| D | ftgmac100.txt | 19 absent, "rgmii" is assumed. Supported values are "rgmii*" and "rmii" for
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-frequency-adf4350 | 7 the fractional-N PLL. It is assumed that the algorithm
|
| D | sysfs-bus-iio-icm42600 | 10 Hardware applied calibration offset (assumed to fix production
|
| /Documentation/devicetree/bindings/regulator/ |
| D | pwm-regulator.txt | 39 defined, <100> is assumed, meaning that
47 If not defined, <0 100> is assumed.
|
| /Documentation/devicetree/bindings/spi/ |
| D | spi-clps711x.txt | 14 which is assumed to be in the same device tree, with and marked
|
| /Documentation/devicetree/bindings/net/can/ |
| D | fsl,flexcan.yaml | 73 node then controller is assumed to be little endian. If this property is
74 present then controller is assumed to be big endian.
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-rk3x.yaml | 82 (t(r) in I2C specification). If not specified this is assumed to be
90 (t(f) in the I2C specification). If not specified this is assumed to
|
| /Documentation/devicetree/bindings/ufs/ |
| D | ufshcd-pltfrm.txt | 48 defined or a value in the array is "0" then it is assumed
61 Note: If above properties are not defined it can be assumed that the supply
|
| D | ufs-mediatek.txt | 23 defined or a value in the array is "0" then it is assumed
|
| D | ufs-hisi.txt | 19 defined or a value in the array is "0" then it is assumed
|
| /Documentation/devicetree/bindings/input/ |
| D | qcom,pm8941-pwrkey.txt | 42 When property is omitted KEY_POWER is assumed.
|
| /Documentation/hwmon/ |
| D | g760a.rst | 24 cycle counts of an assumed 32kHz clock source.
|
| /Documentation/devicetree/bindings/iio/dac/ |
| D | dpot-dac.txt | 3 It is assumed that the dpot is used as a voltage divider between the
|
| /Documentation/devicetree/bindings/iio/light/ |
| D | cm3605.txt | 28 calibration curves for. If not supplied, 100 kOhm will be assumed
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | snps,archs-idu-intc.txt | 23 When no second cell is specified, the interrupt is assumed to be level
|
| /Documentation/devicetree/bindings/mmc/ |
| D | synopsys-dw-mshc-common.yaml | 46 offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A)
|
1234567