Searched full:calculate (Results 1 – 25 of 87) sorted by relevance
1234
| /Documentation/driver-api/media/drivers/ |
| D | sh_mobile_ceu_camera.rst | 72 1. Calculate current sensor scales:
76 2. Calculate "effective" input crop (sensor subwindow) - CEU crop scaled back at
81 3. Calculate new combined scales from "effective" input window to requested user
86 4. Calculate sensor output window by applying combined scales to real input
97 7. Calculate new sensor scales:
101 8. Calculate new CEU crop - apply sensor scales to previously calculated
137 4. Sensor scaled to 3 : 3'. Sensor's scale is (2' - 2) / (3' - 3). Calculate
140 5. Calculate and apply host scale = (6' - 6) / (4' - 4)
142 6. Calculate and apply host crop: 6 - 7 = (5 - 2) * (6' - 6) / (5' - 5)
|
| /Documentation/hwmon/ |
| D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
51 is installed. If a different sense resistor is installed, calculate the real
|
| D | ltc4261.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
51 is installed. If a different sense resistor is installed, calculate the real
|
| D | fam15h_power.rst | 62 calculate the average power consumed by a processor during a
110 v. Calculate the average power consumption for a compute unit over
|
| D | ltc2945.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
51 is installed. If a different sense resistor is installed, calculate the real
|
| D | vexpress.rst | 33 temperature and power usage. Some of them also calculate consumed energy
|
| D | tmp513.rst | 85 register value. Those values are calculate by the hardware using those
|
| /Documentation/ABI/testing/ |
| D | sysfs-cfq-target-latency | 8 use it to calculate the time slice used for every task.
|
| D | sysfs-bus-iio-adc-max9611 | 16 attributes as it is used to calculate two different values: power load and
|
| D | sysfs-driver-w1_ds28e17 | 18 Description: When written, this file sets the multiplier used to calculate
|
| /Documentation/devicetree/bindings/net/ |
| D | arc_emac.txt | 18 The clock frequency is needed to calculate and set polling period of EMAC.
|
| D | emac_rockchip.txt | 20 - clock-names: Shall be "hclk" for the host clock needed to calculate and set
|
| D | xilinx_axienet.txt | 42 Used to calculate MDIO clock divisor. If not specified, it is
|
| /Documentation/networking/ |
| D | 6lowpan.rst | 10 The priv_size of each interface should be calculate by::
|
| /Documentation/devicetree/bindings/mfd/ |
| D | mxs-lradc.txt | 14 - fsl,ave-ctrl: number of samples per direction to calculate an average value.
|
| /Documentation/driver-api/thermal/ |
| D | power_allocator.rst | 200 allocator governor to calculate how much power to give to each cooling
220 on failure. This is currently used by thermal core to calculate the
235 Calculate a cooling device state that would make the device consume at
|
| /Documentation/security/tpm/ |
| D | tpm_event_log.rst | 45 before the Linux EFI stub gets to run. Thus, it needs to calculate and save the
|
| /Documentation/usb/ |
| D | misc_usbsevseg.rst | 47 to set the nth decimal place calculate 10 ** n
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | dongwoon,dw9768.yaml | 61 factor to calculate VCM ring periodic time Tvib.
|
| /Documentation/w1/masters/ |
| D | omap-hdq.rst | 36 be used to calculate the CRC and pass back an appropriate slave ID to the W1
|
| /Documentation/devicetree/bindings/gpio/ |
| D | socionext,uniphier-gpio.yaml | 92 // UNIPHIER_GPIO_PORT() is a helper macro to calculate 29 * 8 + 4.
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | adi,ltc2947.yaml | 36 calculate charge and energy so that, they can be only accumulated for
|
| /Documentation/userspace-api/media/v4l/ |
| D | colorspaces.rst | 42 can take an SPD and calculate the stimulus for each color receptor.
140 encoding and the colorspace. From that information you can calculate the
|
| /Documentation/trace/ |
| D | uprobetracer.rst | 19 user to calculate the offset of the probepoint in the object.
126 .. note:: User has to explicitly calculate the offset of the probe-point
|
| /Documentation/devicetree/bindings/regulator/ |
| D | pwm-regulator.txt | 18 regulator-{min,max}-microvolt properties to calculate
|
1234