Searched full:duration (Results 1 – 25 of 89) sorted by relevance
1234
| /Documentation/leds/ |
| D | ledtrig-transient.rst | 68 This trigger exports three properties, activate, state, and duration. When
71 - duration allows setting timer value in msecs. The initial value is 0.
73 duration as needed. The initial and default value is 0. This will allow
74 duration to be set after trigger activation.
76 duration.
82 to allow duration to be set.
85 duration running.
89 duration
90 - one shot timer value. When activate is set, duration value
93 echo new_value > duration
[all …]
|
| D | leds-sc27xx.rst | 20 - Min stage duration: 125 ms
21 - Max stage duration: 31875 ms
23 Since the stage duration step is 125 ms, the duration should be
|
| /Documentation/devicetree/bindings/watchdog/ |
| D | ziirave-wdt.txt | 9 - reset-duration-ms: Duration of the pulse generated when the watchdog times
18 reset-duration-ms = <30>;
|
| D | aspeed-wdt.txt | 41 - aspeed,ext-pulse-duration: External signal pulse duration in microseconds
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-papr-pmem | 55 * "HostSDur" : Host Store Duration
56 * "HostLDur" : Host Load Duration
59 * "MedRDur " : Media Read Duration
60 * "MedWDur " : Media Write Duration
|
| D | sysfs-class-led-trigger-pattern | 6 the brightness for the specified duration with one software
10 duration (ms).
|
| D | sysfs-driver-hid-prodikeys | 15 Allows control (via software) the sustain duration of a
|
| D | sysfs-class-led-trigger-netdev | 13 Specifies the duration of the LED blink in milliseconds.
|
| D | sysfs-driver-xen-blkback | 35 controls the duration in milliseconds that blkback will not
|
| /Documentation/driver-api/thermal/ |
| D | cpu-idle-cooling.rst | 36 duration in a controlled period, the SoC temperature will
37 decrease. Acting on the idle state duration or the idle cycle
48 belong to the same cluster, with a duration greater than the cluster
69 We use a fixed duration of idle injection that gives an acceptable
94 starting state is selected. With a fixed idle duration and the duty
95 cycle (aka the cooling device state), the running duration can be
130 The idle injection duration value must comply with the constraints:
173 injection duration, we can compute the running duration with::
192 * The injected idle duration must be greater than the idle state
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-trigger-pattern.txt | 3 The pattern is given by a series of tuples, of brightness and duration (ms).
5 specified duration. Duration of 0 means brightness should immediately change to
9 the tuple with duration less than dimming interval (50ms) is treated as a step
|
| /Documentation/devicetree/bindings/net/ |
| D | arc_emac.txt | 12 - phy-reset-duration : Reset duration in milliseconds. Should present
14 will have the duration be 1 millisecond. Numbers greater than 1000 are
|
| D | fsl-fec.txt | 52 - phy-reset-duration : Reset duration in milliseconds. Should present
54 will have the duration be 1 millisecond. Numbers greater than 1000 are
|
| /Documentation/devicetree/bindings/net/dsa/ |
| D | lan9303.txt | 14 - reset-duration: reset duration in milliseconds, defaults to 200 ms
41 reset-duration = <200>;
78 reset-duration = <100>;
|
| /Documentation/devicetree/bindings/memory-controllers/ |
| D | st,stm32-fmc2-ebi.yaml | 131 description: This property defines the duration of the address setup
135 description: This property defines the duration of the address hold
140 description: This property defines the duration of the data setup phase
148 description: This property defines the duration of the data hold phase
160 description: This property defines the duration of the address setup
164 description: This property defines the duration of the address hold
169 description: This property defines the duration of the data setup
177 description: This property defines the duration of the data hold phase
182 duration in nanoseconds for synchronous transactions. When this timing
|
| /Documentation/devicetree/bindings/thermal/ |
| D | thermal-idle.yaml | 34 duration-us:
36 The idle duration in microsecond the device should cool down.
71 duration-us = <10000>;
87 duration-us = <10000>;
|
| /Documentation/admin-guide/pm/ |
| D | cpuidle.rst | 156 duration* from now on) and it can use that information somehow along with the
157 time until the closest timer to estimate the idle duration in future. How the
208 the tick period length. Moreover, in that case the idle duration of any CPU
270 idle duration and uses the predicted value for idle state selection.
287 up and the closer the sleep length is to the observed idle duration, the closer
290 falls into to obtain the first approximation of the predicted idle duration.
293 idle duration prediction. Namely, it saves the last 8 observed idle duration
294 values and, when predicting the idle duration next time, it computes the average
298 interval" value. Otherwise, the longest of the saved observed idle duration
306 taken as the predicted idle duration.
[all …]
|
| /Documentation/devicetree/bindings/input/ |
| D | ti,palmas-pwrbutton.txt | 16 - ti,palmas-long-press-seconds: Duration in seconds which the power
20 - ti,palmas-pwron-debounce-milli-seconds: Duration in milliseconds
|
| D | input-reset.txt | 18 timeout-ms: duration keys must be pressed together in milliseconds before
|
| D | input.yaml | 32 Duration in seconds which the key should be kept pressed for device to
|
| /Documentation/devicetree/bindings/power/ |
| D | domain-idle-state.yaml | 33 state. Note that, the exit-latency-us duration may be guaranteed only
43 The minimum residency duration in microseconds after which the idle
|
| /Documentation/devicetree/bindings/iio/accel/ |
| D | lis302.txt | 43 - st,wu-duration-1: duration register for Free-Fall/Wake-Up
45 - st,wu-duration-2: duration register for Free-Fall/Wake-Up
|
| /Documentation/accounting/ |
| D | taskstats-struct.rst | 153 /* Accumulated RSS usage in duration of a task, in MBytes-usecs.
161 /* Accumulated virtual memory usage in duration of a task.
166 /* High watermark of RSS usage in duration of a task, in KBytes. */
169 /* High watermark of VM usage in duration of a task, in KBytes. */
|
| /Documentation/vm/ |
| D | highmem.rst | 55 * vmap(). This can be used to make a long duration mapping of multiple
59 * kmap(). This permits a short duration mapping of a single page. It needs
64 * kmap_atomic(). This permits a very short duration mapping of a single
|
| /Documentation/devicetree/bindings/pps/ |
| D | pps-gpio.txt | 12 - echo-active-ms: duration in ms of the active portion of the echo pulse
|
1234