Home
last modified time | relevance | path

Searched +full:filter +full:- +full:gpios (Results 1 – 8 of 8) sorted by relevance

/Documentation/devicetree/bindings/iio/adc/
Dadi,ad7780.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Michael Hennerich <michael.hennerich@analog.com>
13 The ad7780 is a sigma-delta analog to digital converter. This driver provides
15 Its interface also allows writing on the FILTER and GAIN GPIO pins on the
20 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7170.pdf
22 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7171.pdf
24 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7780.pdf
26 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7781.pdf
[all …]
Dadi,ad7768-1.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/iio/adc/adi,ad7768-1.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Analog Devices AD7768-1 ADC device driver
10 - Michael Hennerich <michael.hennerich@analog.com>
14 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf
18 const: adi,ad7768-1
26 clock-names:
32 vref-supply:
[all …]
/Documentation/devicetree/bindings/i2c/
Di2c.txt8 -----------------------------
10 - #address-cells - should be <1>. Read more about addresses below.
11 - #size-cells - should be <0>.
12 - compatible - name of I2C bus controller
21 -----------------------------
26 - clock-frequency
29 - i2c-bus
31 devices and non-I2C devices, the 'i2c-bus' subnode can be used for
32 populating I2C devices. If the 'i2c-bus' subnode is present, only
34 '#address-cells' and '#size-cells' must be defined under this subnode
[all …]
/Documentation/devicetree/bindings/gpio/
Dgpio-xra1403.txt1 GPIO Driver for XRA1403 16-BIT GPIO Expander With Reset Input from EXAR
3 The XRA1403 is an 16-bit GPIO expander with an SPI interface. Features available:
4 - Individually programmable inputs:
5 - Internal pull-up resistors
6 - Polarity inversion
7 - Individual interrupt enable
8 - Rising edge and/or Falling edge interrupt
9 - Input filter
10 - Individually programmable outputs
11 - Output Level Control
[all …]
/Documentation/devicetree/bindings/input/touchscreen/
Dtsc2007.txt4 - compatible: must be "ti,tsc2007".
5 - reg: I2C address of the chip.
6 - ti,x-plate-ohms: X-plate resistance in ohms.
9 - gpios: the interrupt gpio the chip is connected to (trough the penirq pin).
12 - interrupts: (gpio) interrupt to which the chip is connected
14 - ti,max-rt: maximum pressure.
15 - ti,fuzzx: specifies the absolute input fuzz x value.
16 If set, it will permit noise in the data up to +- the value given to the fuzz
17 parameter, that is used to filter noise from the event stream.
18 - ti,fuzzy: specifies the absolute input fuzz y value.
[all …]
/Documentation/driver-api/
Dptp.rst1 .. SPDX-License-Identifier: GPL-2.0
18 - Set time
19 - Get time
20 - Shift the clock by a given offset atomically
21 - Adjust clock frequency
24 - Time stamp external events
25 - Period output signals configurable from user space
26 - Low Pass Filter (LPF) access from user space
27 - Synchronization of the Linux system time via the PPS subsystem
65 ancillary feature, then the driver should just return -EOPNOTSUPP
[all …]
/Documentation/devicetree/bindings/sound/
Dst,sta350.txt7 - compatible: "st,sta350"
8 - reg: the I2C address of the device for I2C
9 - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
12 - power-down-gpios: a GPIO spec for the power down pin. If specified,
16 - vdd-dig-supply: regulator spec, providing 3.3V
17 - vdd-pll-supply: regulator spec, providing 3.3V
18 - vcc-supply: regulator spec, providing 5V - 26V
22 - st,output-conf: number, Selects the output configuration:
23 0: 2-channel (full-bridge) power, 2-channel data-out
24 1: 2 (half-bridge). 1 (full-bridge) on-board power
[all …]
/Documentation/hwmon/
Dlm93.rst10 Addresses scanned: I2C 0x2c-0x2e
18 Addresses scanned: I2C 0x2c-0x2e
24 - Mark M. Hoffman <mhoffman@lightlink.com>
25 - Ported to 2.6 by Eric J. Bowersox <ericb@aspsys.com>
26 - Adapted to 2.6.20 by Carsten Emde <ce@osadl.org>
27 - Modified for mainline integration by Hans J. Koch <hjk@hansjkoch.de>
30 -----------------
33 Set to non-zero to force some initializations (default is 0).
38 Configures in7 and in8 limit type, where 0 means absolute and non-zero
54 --------------------
[all …]