Searched full:gnd (Results 1 – 21 of 21) sorted by relevance
| /Documentation/spi/ |
| D | butterfly.rst | 39 GND J403.GND pin 23/GND
52 GND J400.GND pin 24/GND
70 GND J403.GND pin 22/GND
73 GND J402.GND(P2) pin 25/GND
|
| D | spi-lm70llp.rst | 47 GND 25 - GND 7
|
| /Documentation/admin-guide/auxdisplay/ |
| D | cfag12864b.rst | 65 (11) [GND]---( 2) Ground
67 (13) [GND]---(15) Read / Write
72 Ground (18)---[GND] [+5v]---(19) LED +
73 Ground (19)---[GND]
74 Ground (20)---[GND] E A Values:
75 Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm
76 Ground (22)---[GND] | - P1 = Preset = 10 Kohm
77 Ground (23)---[GND] ---- S ------( 3) V0 - P2 = Preset = 1 Kohm
78 Ground (24)---[GND] | |
79 Ground (25)---[GND] [GND]---[P2]---[R]---(20) LED -
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | ti,ads1015.yaml | 53 4: Voltage over AIN0 and GND.
54 5: Voltage over AIN1 and GND.
55 6: Voltage over AIN2 and GND.
56 7: Voltage over AIN3 and GND.
|
| D | ti,adc12138.yaml | 42 (Note that this must not go below GND or exceed vref-p)
|
| D | qcom,spmi-vadc.yaml | 115 specified VADC will use the VDD reference (1.8V) and GND for
121 the VDD reference (1.875V) and GND for channel calibration. If
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-adc-hi8435 | 7 Could be either "GND-Open" or "Supply-Open" mode. Y is a
19 is separately set for "GND-Open" and "Supply-Open" modes.
38 is separately set for "GND-Open" and "Supply-Open" modes.
|
| /Documentation/devicetree/bindings/sound/ |
| D | qcom,msm8916-wcd-analog.txt | 46 - qcom,gnd-jack-type-normally-open: boolean, present if gnd pin on jack is
48 its assumed that gnd pin on jack is NC
|
| /Documentation/i2c/busses/ |
| D | i2c-parport.rst | 75 GND GND
88 - Pins 18-25 of the parallel port connected to GND.
135 GND GND
|
| /Documentation/input/devices/ |
| D | walkera0701.rst | 21 pin 3 is GND. Between pin 3 and CPU 5k6 resistor can be found. To get
31 / O 4 3 O \ pin 3 (GND) LED ________________ 10 ACK
35 ------- 3 __________________________________|________________ 25 GND
|
| D | amijoy.rst | 36 8 Gnd
53 8 Gnd
70 8 Gnd
87 8 Gnd
|
| D | joystick-parport.rst | 479 8 (Gnd) 18 (Gnd)
607 18-25 GND Signal Ground
|
| /Documentation/devicetree/bindings/mmc/ |
| D | sdhci-atmel.txt | 20 For instance on SAMA5D2, the pin is usually tied to the GND with a resistor
|
| /Documentation/devicetree/bindings/iio/afe/ |
| D | voltage-divider.txt | 21 GND
|
| /Documentation/devicetree/bindings/mfd/ |
| D | tps6507x.txt | 29 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND.
|
| /Documentation/driver-api/gpio/ |
| D | driver.rst | 147 GND GND
183 GND
203 By disabling the P-MOS transistor, the output can be driven between GND and
|
| /Documentation/driver-api/ |
| D | pps.rst | 229 18-25 GND *-----------*
|
| D | pinctl.rst | 208 effectively disconnected. You may be able to connect an input pin to VDD or GND
428 pins you see some will be taken by things like a few VCC and GND to feed power
|
| /Documentation/networking/ |
| D | plip.rst | 184 GND->ERROR 18 - 15
|
| /Documentation/devicetree/bindings/iio/temperature/ |
| D | adi,ltc2983.yaml | 425 /*2-wire, internal gnd, no current rotation*/
|
| /Documentation/admin-guide/media/ |
| D | bttv.rst | 625 - CP9..1=100001001 (1: 0-Ohm-Widerstand gegen GND unbestückt; 0: bestückt)
|