Searched full:gpio4 (Results 1 – 25 of 57) sorted by relevance
123
| /Documentation/devicetree/bindings/fpga/ |
| D | altera-passive-serial.txt | 26 nconfig-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
27 nstat-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
28 confd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | sht15.txt | 16 clk-gpios = <&gpio4 12 0>;
17 data-gpios = <&gpio4 13 0>;
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | tsc2005.txt | 28 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
51 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
52 interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
|
| D | tsc2007.txt | 32 interrupt-parent = <&gpio4>;
34 gpios = <&gpio4 0 0>;
|
| D | sx8654.txt | 22 reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
|
| D | elan,elants_i2c.yaml | 65 interrupt-parent = <&gpio4>;
|
| /Documentation/devicetree/bindings/phy/ |
| D | phy-mapphone-mdm6600.txt | 22 motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
23 <&gpio4 8 GPIO_ACTIVE_HIGH>,
|
| /Documentation/devicetree/bindings/mfd/ |
| D | as3711.txt | 34 - su2-fbprot-gpio4 : GPIO4 is used for over-voltage protection
68 su2-fbprot-gpio4;
|
| D | retu.txt | 20 interrupt-parent = <&gpio4>;
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | cirrus,lochnagar.yaml | 90 enum: [ fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4,
92 codec-gpio3, codec-gpio4, codec-gpio5, codec-gpio6,
94 dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6,
125 enum: [ aif, fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4,
127 codec-gpio3, codec-gpio4, codec-gpio5, codec-gpio6,
129 dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6,
|
| D | qcom,msm8974-pinctrl.txt | 105 pins = "gpio4", "gpio5";
110 pins = "gpio4";
|
| D | qcom,pmic-gpio.txt | 92 gpio1-gpio4 for pm8005
96 gpio1-gpio4 for pm8916
109 gpio1-gpio12 for pm8150b (holes on gpio3, gpio4, gpio7)
|
| /Documentation/devicetree/bindings/sound/ |
| D | rt5640.txt | 33 2: using GPIO4 pin as dmic2 data pin
43 6: Use GPIO4 for jack-detect
|
| D | tpa6130a2.txt | 26 power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
|
| D | dmic.txt | 18 dmicen-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
|
| D | tas2552.txt | 32 enable-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
|
| D | rt5665.txt | 23 1: using GPIO4 pin as dmic1 data pin
|
| /Documentation/devicetree/bindings/iio/light/ |
| D | vcnl4035.txt | 16 interrupt-parent = <&gpio4>;
|
| /Documentation/devicetree/bindings/input/ |
| D | ilitek,ili2xxx.txt | 24 interrupt-parent = <&gpio4>;
|
| D | elan_i2c.txt | 38 interrupt-parent = <&gpio4>;
|
| /Documentation/devicetree/bindings/net/can/ |
| D | holt_hi311x.txt | 19 interrupt-parent = <&gpio4>;
|
| D | microchip,mcp251x.txt | 24 interrupt-parent = <&gpio4>;
|
| /Documentation/devicetree/bindings/misc/ |
| D | eeprom-93xx46.txt | 24 select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/rtc/ |
| D | rtc-ds1307.txt | 49 interrupt-parent = <&gpio4>;
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | novatek,nt35510.yaml | 51 reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
|
123