Searched full:ldo1 (Results 1 – 25 of 62) sorted by relevance
123
| /Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd70528-regulator.txt | 4 - regulator-name: should be "buck1", "buck2", "buck3", "ldo1", "ldo2", "ldo3",
12 BUCK1, BUCK2, BUCK3, LDO1, LDO2, LDO3, LED_LDO1, LED_LDO2
40 ldo1: LDO1 {
41 regulator-name = "ldo1";
|
| D | mt6360-regulator.yaml | 14 after their hardware counterparts buck1/2 or ldo1/2/3/5/6/7
21 description: Input supply phandle(s) for LDO1/2/3
80 ldo1 {
81 regulator-compatible = "LDO1";
82 regulator-name = "mt6360,ldo1";
|
| D | tps65218.txt | 8 after their hardware counterparts: dcdc[1-6] and ldo1
16 regulator-dcdc5, regulator-dcdc6, regulator-ldo1, regulator-ls3.
67 ldo1: regulator-ldo1 {
|
| D | ltc3589.txt | 9 ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as
13 nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify
22 0.3625 * (1 + R1/R2) V and 0.75 * (1 + R1/R2) V. Regulators bb-out and ldo1
26 and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not
71 ldo1_reg: ldo1 {
|
| D | pv88090.txt | 11 BUCK1, BUCK2, BUCK3, LDO1, and LDO2.
51 LDO1 {
52 regulator-name = "ldo1";
|
| D | ltc3676.txt | 9 ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as
13 nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify
24 Regulators ldo1, ldo2, and ldo4 have a fixed 0.725 V reference and thus output
25 0.725 * (1 + R1/R2) V. The ldo3 regulator is fixed to 1.8 V. The ldo1 standby
|
| D | qcom,rpmh-regulator.txt | 26 PM8009: smps1 - smps2, ldo1 - ldo7
27 PM8150: smps1 - smps10, ldo1 - ldo18
28 PM8150L: smps1 - smps8, ldo1 - ldo11, bob, flash, rgb
29 PM8998: smps1 - smps13, ldo1 - ldo28, lvs1 - lvs2
31 PM6150: smps1 - smps5, ldo1 - ldo19
32 PM6150L: smps1 - smps8, ldo1 - ldo11, bob
|
| D | max8925-regulator.txt | 8 - LDO1 for LDO LDO1
|
| D | slg51000.txt | 29 ldo1
46 ldo1 {
47 regulator-name = "ldo1";
|
| D | wlf,arizona.yaml | 27 ldo1:
29 Initial data for the LDO1 regulator.
|
| D | 88pm800.txt | 14 buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7,
30 ldo1 {
|
| D | nxp,pca9450-regulator.yaml | 22 #LDO1, LDO2, LDO3, LDO4, LDO5
142 ldo1: LDO1 {
143 regulator-name = "LDO1";
|
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
35 LDO1 {
36 regulator-name = "ldo1";
|
| D | lp872x.txt | 34 LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck)
35 LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2)
61 vaf: ldo1 {
105 vcam_io: ldo1 {
|
| D | mcp16502-regulator.txt | 18 5) LDO1 - LDO (1.2 - 3.7 V)
112 LDO1 {
113 regulator-name = "LDO1";
|
| /Documentation/devicetree/bindings/mfd/ |
| D | wm831x.txt | 43 ldo1 : LDO1
75 ldo1: ldo1 {
76 regulator-name = "LDO1";
|
| D | lp873x.txt | 12 buck0, buck1, ldo0 or ldo1.
26 ldo1-in-supply = <&vsys_3v3>;
59 lp8733_ldo1: ldo1 {
60 regulator-name = "lp8733-ldo1";
|
| D | da9055.txt | 35 ldo1 : regulator LDO1
65 ldo1: LDO1 {
|
| D | tps65912.txt | 43 ldo1 {
44 regulator-name = "ldo1";
|
| D | da9052-i2c.txt | 23 ldo1 : regulator LDO1
|
| D | rohm,bd70528-pmic.txt | 73 ldo1: LDO1 {
74 regulator-name = "ldo1";
|
| D | da9062.txt | 60 ldo1 : LDO_1
70 ldo1 : LDO_1
115 DA9062_LDO1: ldo1 {
|
| /Documentation/devicetree/bindings/sound/ |
| D | rt5668.txt | 28 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
45 realtek,ldo1-en-gpios =
|
| D | rt5665.txt | 35 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
66 realtek,ldo1-en-gpios =
|
| D | rt5659.txt | 41 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
76 realtek,ldo1-en-gpios =
|
123