Searched full:microseconds (Results 1 – 25 of 99) sorted by relevance
1234
| /Documentation/userspace-api/media/rc/ |
| D | lirc-get-rec-resolution.rst | 13 LIRC_GET_REC_RESOLUTION - Obtain the value of receive resolution, in microseconds.
20 ``int ioctl(int fd, LIRC_GET_REC_RESOLUTION, __u32 *microseconds)``
28 ``microseconds``
29 Resolution, in microseconds.
|
| D | lirc-dev-intro.rst | 106 Signifies the presence of IR in microseconds.
110 Signifies absence of IR in microseconds.
123 this packet will be sent, with the number of microseconds with
133 The values are alternating pulse and space lengths, in microseconds. The
|
| D | lirc-set-rec-timeout.rst | 34 Timeout, in microseconds.
|
| /Documentation/ABI/testing/ |
| D | sysfs-module | 22 microframe to be 80%, that is 100 microseconds out of 125
23 microseconds (full microframe).
27 microseconds of isochronous bandwidth per microframe to work
32 microseconds of periodic bandwidth per microframe.
|
| D | debugfs-hyperv | 14 microseconds (inclusive).
21 Description: Fuzz testing message delay value between 0 - 1000 microseconds
|
| D | sysfs-class-rc-nuvoton | 8 All values are in microseconds.
|
| D | sysfs-class-led-flash | 26 Hardware timeout for flash, in microseconds. The flash strobe
36 Maximum flash timeout for this LED, in microseconds.
|
| /Documentation/devicetree/bindings/power/ |
| D | domain-idle-state.yaml | 32 The worst case latency in microseconds required to enter the idle
38 The worst case latency in microseconds required to exit the idle
43 The minimum residency duration in microseconds after which the idle
|
| /Documentation/devicetree/bindings/net/ |
| D | mdio.yaml | 38 RESET pulse width in microseconds. It applies to all MDIO devices
44 Delay after reset deassert in microseconds. It applies to all MDIO
92 Delay after the reset was asserted in microseconds. If this
97 Delay after the reset was deasserted in microseconds. If
|
| /Documentation/userspace-api/media/v4l/ |
| D | pixfmt-meta-d4xx.rst | 57 - Exposure time (in microseconds) used to capture the frame
91 - Time in microseconds from the beginning of a frame till its middle
93 - Time, used to read out a frame in microseconds
95 - Frame exposure time in microseconds
97 - In microseconds = 1000000 / framerate
99 - Time in microseconds from start of frame to data in USB buffer
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-arb-gpio-challenge.txt | 34 microseconds).
50 - slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us.
51 - wait-retry-us: we'll attempt another claim after this many microseconds.
53 - wait-free-us: we'll give up after this many microseconds. Default is 50000 us.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 91 -maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds
95 -maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds
111 Here supported time periods by device in microseconds are as follows:
112 MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds.
113 MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
114 MAX77663 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | fixed-regulator.yaml | 50 description: startup time in microseconds
54 description: off delay time in microseconds
|
| D | regulator.yaml | 64 description: The time taken, in microseconds, for the supply rail to
73 description: Settling time, in microseconds, for voltage change if regulator
78 description: Settling time, in microseconds, for voltage increase if
84 description: Settling time, in microseconds, for voltage decrease if
|
| D | tps65132-regulator.txt | 22 asserted for during active discharge, in microseconds.
|
| /Documentation/devicetree/bindings/input/ |
| D | qcom,pm8xxx-keypad.txt | 57 Definition: time in microseconds that key must be pressed or release
63 Definition: time in microseconds to pause between successive scans
|
| D | qcom,pm8xxx-pwrkey.txt | 28 Definition: time in microseconds that key must be pressed or release
|
| D | qcom,pm8941-pwrkey.txt | 27 Definition: time in microseconds that key must be pressed or released
|
| D | gpio-matrix-keypad.txt | 25 - col-scan-delay-us: delay, measured in microseconds, that is needed
|
| /Documentation/ABI/stable/ |
| D | sysfs-bus-w1 | 4 Description: Bus scanning interval, microseconds component.
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | at91_adc.txt | 13 - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
28 - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
|
| /Documentation/scheduler/ |
| D | sched-bwc.rst | 12 each given "period" (microseconds), a task group is allocated up to "quota"
13 microseconds of CPU time. That quota is assigned to per-cpu run queues in
28 cpu.cfs_quota_us: the total available run-time within a period (in microseconds)
29 cpu.cfs_period_us: the length of a period (in microseconds)
|
| /Documentation/devicetree/bindings/rng/ |
| D | timeriomem_rng.txt | 6 - period : wait time in microseconds to use between samples
|
| /Documentation/devicetree/bindings/spi/ |
| D | spi-controller.yaml | 134 Delay, in microseconds, after a read transfer.
145 Delay, in microseconds, after a write transfer.
|
| /Documentation/devicetree/bindings/sound/ |
| D | ti,tas5086.txt | 14 - ti,charge-period: This property should contain the time in microseconds
|
1234