Searched full:selecting (Results 1 – 25 of 76) sorted by relevance
1234
| /Documentation/leds/ |
| D | ledtrig-usbport.rst | 9 It requires selecting USB ports that should be observed. All available ones are
10 listed as separated entries in a "ports" subdirectory. Selecting is handled by
13 Please note that this trigger allows selecting multiple USB ports for a single
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-led-trigger-usbport | 8 selected for the USB port trigger. Selecting ports makes trigger
|
| D | sysfs-bus-iio-counter-104-quad-8 | 76 clock mode. Selecting non-quadrature clock mode will disable
85 direction control input, with B = 1 selecting UP Count
86 mode and B = 0 selecting Down Count mode.
|
| D | sysfs-bus-event_source-devices-events | 63 need to be provided by the user selecting the particular event.
|
| /Documentation/admin-guide/hw-vuln/ |
| D | index.rst | 6 possible mitigations along with guidance for selecting mitigations if they
|
| /Documentation/devicetree/bindings/clock/ |
| D | gpio-mux-clock.txt | 11 - select-gpios : GPIO reference for selecting the parent clock.
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | actions,s900-pinctrl.txt | 57 These pins are used for selecting the pull control and schmitt
91 group. These pin groups are used for selecting the pinmux
113 These pin groups are used for selecting the drive strength
126 These pin groups are used for selecting the slew rate
|
| D | actions,s700-pinctrl.txt | 57 These pins are used for selecting the pull control and schmitt
85 group. These pin groups are used for selecting the pinmux
103 These pin groups are used for selecting the drive strength
|
| /Documentation/networking/ |
| D | secid.rst | 10 the label of the flow. This label of the flow is currently used in selecting
|
| /Documentation/block/ |
| D | deadline-iosched.rst | 9 Selecting IO schedulers
12 selecting an io scheduler on a per-device basis.
|
| /Documentation/driver-api/media/drivers/ |
| D | davinci-vpbe-devel.rst | 32 - add support for selecting external encoder as default at probe time.
|
| /Documentation/userspace-api/media/v4l/ |
| D | common.rst | 12 - Changing device properties, selecting a video and audio input, video
|
| D | ext-ctrls-image-process.rst | 35 by selecting the desired horizontal and vertical blanking. The unit
|
| /Documentation/devicetree/bindings/sound/ |
| D | adi,adau1701.txt | 19 - adi,pin-config: An array of 12 numerical values selecting one of the
|
| /Documentation/userspace-api/media/dvb/ |
| D | fe-dishnetwork-send-legacy-cmd.rst | 38 It provides a non-standard method for selecting Diseqc voltage on the
|
| D | fe-set-tone.rst | 44 capability of selecting the band. So, it is recommended that applications
|
| D | frontend.rst | 43 control the antenna subsystem, selecting the polarization and choosing
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | bu21013.txt | 6 - reset-gpios : GPIO pin enabling (selecting) chip (CS)
|
| /Documentation/hwmon/ |
| D | lm93.rst | 95 #P1_PROCHOT and #P2_PROCHOT, respectively. Selecting a value not in this
150 are constrained by the hardware. Selecting a value which is not available
160 frequency values are constrained by the hardware. Selecting a value which is
245 the hardware. Selecting a value which is not available will cause the driver
258 The available ramp times are constrained by the hardware. Selecting a value
|
| /Documentation/devicetree/bindings/ |
| D | property-units.txt | 7 prefixes is due to selecting the most commonly used variants.
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-aat1290.txt | 5 respectively. In order to add a capability of selecting the strobe signal source
|
| /Documentation/admin-guide/media/ |
| D | building.rst | 64 The ``HDMI CEC drivers`` option allow selecting platform and USB drivers
122 The remote controller menu allows selecting drivers for specific devices.
143 The ``Remote controller decoders`` option allows selecting the
|
| /Documentation/devicetree/bindings/mfd/ |
| D | cirrus,lochnagar.yaml | 187 A property selecting which of the CODEC minicard micbias outputs
212 A property selecting which of the CODEC minicard micbias outputs
|
| /Documentation/bpf/ |
| D | prog_sk_lookup.rst | 62 selection. Selecting a socket only takes effect if the program has terminated
|
| /Documentation/devicetree/bindings/phy/ |
| D | ti,phy-am654-serdes.txt | 35 for selecting the correct reference clock. This can be used while
|
1234