Searched full:sending (Results 1 – 25 of 177) sorted by relevance
12345678
| /Documentation/devicetree/bindings/serial/ |
| D | rs485.yaml | 23 milliseconds. It corresponds to the delay before sending data.
27 It corresponds to the delay after sending data and actual release
33 description: drive RTS low when sending (default is high).
42 description: enables the receiving of data even while sending data.
|
| D | omap_serial.txt | 25 - rs485-rts-active-high: drive RTS high when sending (default is low).
|
| /Documentation/driver-api/serial/ |
| D | serial-rs485.rst | 68 /* Set logical level for RTS pin equal to 1 when sending: */
70 /* or, set logical level for RTS pin equal to 0 when sending: */
73 /* Set logical level for RTS pin equal to 1 after sending: */
75 /* or, set logical level for RTS pin equal to 0 after sending: */
84 /* Set this flag if you want to receive data even while sending data */
|
| /Documentation/sparc/ |
| D | console.rst | 1 Steps for sending 'break' on sunhv console
|
| /Documentation/process/ |
| D | email-clients.rst | 61 and successfully apply it with 'patch' before sending patches to Linux
68 Here are some specific MUA configuration hints for editing and sending
83 In the :menuselection:`Sending Preferences` section:
86 - :menuselection:`Strip Whitespace Before Sending` must be ``disabled``
146 KMail 1.13.5 (KDE 4.5.4), KMail will apply word wrapping when sending
149 long lines, you must make the composer window very wide before sending
319 Does not work for sending patches.
|
| /Documentation/devicetree/bindings/iio/proximity/ |
| D | devantech-srf04.yaml | 14 - trigger-gpio is raised by the driver to start sending out an ultrasonic
16 - echo-gpio is held high by the sensor after sending ultrasonic burst
|
| /Documentation/devicetree/bindings/ata/ |
| D | sata_highbank.yaml | 33 sending an SGPIO pattern.
39 sending an SGPIO pattern.
|
| /Documentation/devicetree/bindings/power/reset/ |
| D | qnap-poweroff.txt | 5 Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the
|
| /Documentation/timers/ |
| D | no_hz.rst | 68 If a CPU is idle, there is little point in sending it a scheduling-clock
73 The CONFIG_NO_HZ_IDLE=y Kconfig option causes the kernel to avoid sending
81 is strong motivation to avoid sending scheduling-clock interrupts to
107 If a CPU has only one runnable task, there is little point in sending it
113 sending scheduling-clock interrupts to CPUs with a single runnable task,
122 again strong motivation to avoid sending scheduling-clock interrupts.
271 this CPU, so there is no point in sending a scheduling-clock
|
| /Documentation/admin-guide/blockdev/drbd/ |
| D | disk-states-8.dot | 15 Failed -> Diskless [ label = "sending notify to peer" ]
|
| /Documentation/ABI/obsolete/ |
| D | sysfs-driver-intel_pmc_bxt | 1 These files allow sending arbitrary IPC commands to the PMC/SCU which
|
| /Documentation/networking/device_drivers/ethernet/huawei/ |
| D | hinic.rst | 58 Application Programmable Interface commands(API CMD) - Interface for sending
61 Management (MGMT) - the PF to MGMT channel that uses API CMD for sending MGMT
77 Command Queues(CMDQ) - The queues for sending commands for IO management and is
|
| /Documentation/userspace-api/media/rc/ |
| D | lirc-dev-intro.rst | 49 LIRC supports some modes of receiving and sending IR codes, as shown
58 This mode is for both sending and receiving IR.
60 For transmitting (aka sending), create a ``struct lirc_scancode`` with
|
| /Documentation/networking/ |
| D | ipvs-sysctl.rst | 180 It controls sending icmp error messages (ICMP_DEST_UNREACH)
239 parts of memory when the sending rate is lower than the queuing
290 The version of the synchronisation protocol used when sending
294 should be used when sending synchronisation messages to a legacy
|
| D | ipsec.rst | 36 when sending non-compressed packet to the peer (whether or not packet len
|
| /Documentation/hid/ |
| D | uhid.rst | 48 The first thing you should do is sending an UHID_CREATE2 event. This will
50 start sending data to and reading data from UHID. However, unless UHID sends the
99 You can create a new device by sending UHID_CREATE2 again. There is no need to
103 You must send UHID_CREATE2 before sending input to the kernel! This event
|
| /Documentation/devicetree/bindings/clock/ |
| D | hi3660-clock.txt | 25 - mboxes: Phandle to the mailbox for sending message to MCU.
|
| /Documentation/networking/caif/ |
| D | caif.rst | 63 - 0x02 means SENDING, this is a transient state.
126 notified that sending is completed.
|
| /Documentation/sound/cards/ |
| D | serial-u16550.rst | 61 sent to, with midiCnD1 sending to Out 1, midiCnD2 to Out 2, midiCnD4 to
77 but does not allow sending the same byte simultaneously to multiple MIDI Outs.
|
| /Documentation/translations/zh_CN/process/ |
| D | email-clients.rst | 72 在"Sending Preferences"部分：
75 - "Strip Whitespace Before Sending"必须关闭
|
| /Documentation/driver-api/thermal/ |
| D | x86_pkg_temperature_thermal.rst | 47 Setting 0, stops sending thermal notifications.
|
| /Documentation/driver-api/i3c/ |
| D | protocol.rst | 132 payload is either sent by the master sending the command (write CCC command),
135 Note that, when sending a CCC command to a specific device, the device address
171 When sending an HDR command, the whole bus has to enter HDR mode, which is done
|
| /Documentation/virt/kvm/ |
| D | vcpu-requests.rst | 68 as well as to avoid sending unnecessary IPIs (see "IPI Reduction"), and
236 sending kick also change the VCPU mode to something !IN_GUEST_MODE. The
247 KVM_REQUEST_WAIT flag changes the condition for sending an IPI from
269 role of ``vcpu->requests``. When sending a posted interrupt, PIR.ON is
|
| /Documentation/userspace-api/media/v4l/ |
| D | dev-mem2mem.rst | 17 supports both output (sending frames from memory to the hardware)
|
| /Documentation/ABI/testing/ |
| D | debugfs-wilco-ec | 33 // Corresponds with sending type 0x00f0 with
|
12345678