Home
last modified time | relevance | path

Searched full:ua (Results 1 – 25 of 32) sorted by relevance

12

/Documentation/devicetree/bindings/iio/adc/
Dpalmas-gpadc.txt26 ti,channel0-current-microamp: Channel 0 current in uA.
27 Values are rounded to derive 0uA, 5uA, 15uA, 20uA.
28 ti,channel3-current-microamp: Channel 3 current in uA.
29 Values are rounded to derive 0uA, 10uA, 400uA, 800uA.
/Documentation/devicetree/bindings/rtc/
Drtc-palmas.txt17 backup battery. Device supports the < 100uA and > 100uA charging.
18 The high current will be > 100uA. Absence of this property will
19 charge battery to lower current i.e. < 100uA.
/Documentation/devicetree/bindings/usb/
Dusb251xb.txt52 attached peripheral (range: 0 - 100000 uA, default 1000 uA)
56 attached peripheral (range: 0 - 510000 uA, default 100000 uA)
60 attached peripheral (range: 0 - 100000 uA, default 1000 uA)
64 attached peripheral (range: 0 - 510000 uA, default 100000 uA)
/Documentation/devicetree/bindings/power/supply/
Dbq25890.txt15 - ti,charge-current: integer, maximum charging current (in uA);
17 constant-voltage phase drops below this value (in uA);
19 phase (in uA);
25 (in uA).
Drt9455_charger.txt10 battery, in uA.
26 - richtek,avg-input-current-regulation: integer, input current value in uA drained by the
28 Default: 500000 uA (500mA)
Dbq24257.txt12 - ti,charge-current: integer, maximum charging current in uA.
14 constant-voltage phase drops below this value (in uA).
23 (in uA). If this property is not specified, the input limit current is
Dsummit,smb347-charger.yaml56 description: Maximum input current from AC/DC input (in uA)
59 description: Maximum input current from USB input (in uA)
62 description: Charge current compensation (in uA)
Dgpio-charger.yaml48 description: List of tuples with current in uA and a GPIO bitmap (in
55 Current limit in uA
Dqcom_smbb.txt45 Value type: <u32>; uA; range [100mA : 3A]
71 Value type: <u32>; uA; range [100mA : 3A]
90 Value type: <u32>; uA; range [100mA : 2.5A]
/Documentation/devicetree/bindings/sound/
Dcs43130.txt24 1 = 7.5uA
25 2 = 12.5uA
26 3 = 15uA
Dcs35l33.txt35 The range starts at 1850000uA and goes to a maximum of 3600000uA
36 with a step size of 15625uA. The default is 2500000uA.
/Documentation/devicetree/bindings/iio/health/
Dmax30102.txt21 Note that each step is approximately 200 microamps, ranging from 0 uA to
22 50800 uA.
/Documentation/devicetree/bindings/mfd/
Das3711.txt15 - su1-max-uA : maximum current
20 - su1-max-uA : maximum current
66 su2-max-uA = <36000>;
Dmax14577.txt24 - maxim,fast-charge-uamp : Current in uA for Fast Charge;
28 - maxim,eoc-uamp : Current in uA for End-Of-Charge mode;
/Documentation/devicetree/bindings/pinctrl/
Dqcom,pmic-gpio.txt152 1: 30uA (PMIC_GPIO_PULL_UP_30)
153 2: 1.5uA (PMIC_GPIO_PULL_UP_1P5)
154 3: 31.5uA (PMIC_GPIO_PULL_UP_31P5)
155 4: 1.5uA + 30uA boost (PMIC_GPIO_PULL_UP_1P5_30)
156 If this property is omitted 30uA strength will be used if
Dmeson,pinctrl.txt62 - drive-strength-microamp: Drive strength for the specified pins in uA.
Dpincfg-node.yaml71 description: sink or source at most X uA
/Documentation/devicetree/bindings/leds/
Dleds-lm3532.txt66 bank. The range is from 5000uA-29800uA in increments
67 of 800uA.
Dleds-lm36274.txt6 the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA.
/Documentation/devicetree/bindings/regulator/
Dqcom,spmi-regulator.txt282 0 = 0.05 uA
283 1 = 0.25 uA
284 2 = 0.55 uA
285 3 = 0.75 uA
Dmax77802.txt61 3: Low Power which reduces the quiescent current down to only 1uA
/Documentation/devicetree/bindings/input/
Diqs269a.yaml292 0: 2.5 uA
293 1: 5 uA
294 2: 10 uA
295 3: 20 uA
/Documentation/devicetree/bindings/iio/dac/
Dad5758.txt57 The following values are currently supported [uA]:
/Documentation/scsi/
Dadvansys.rst45 - ABP940UA/3940UA - Bus-Master PCI Ultra (240 CDB)
60 - ABP980UA/3980UA - Four Channel Bus-Master PCI Ultra (16 CDB Per Chan.)
/Documentation/devicetree/bindings/phy/
Dqcom,qusb2-phy.yaml114 Possible range is - 15mA to 24mA (stepsize of 600 uA).

12