1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * mxuport.c - MOXA UPort series driver
4 *
5 * Copyright (c) 2006 Moxa Technologies Co., Ltd.
6 * Copyright (c) 2013 Andrew Lunn <andrew@lunn.ch>
7 *
8 * Supports the following Moxa USB to serial converters:
9 * 2 ports : UPort 1250, UPort 1250I
10 * 4 ports : UPort 1410, UPort 1450, UPort 1450I
11 * 8 ports : UPort 1610-8, UPort 1650-8
12 * 16 ports : UPort 1610-16, UPort 1650-16
13 */
14
15 #include <linux/kernel.h>
16 #include <linux/module.h>
17 #include <linux/firmware.h>
18 #include <linux/jiffies.h>
19 #include <linux/serial.h>
20 #include <linux/serial_reg.h>
21 #include <linux/slab.h>
22 #include <linux/tty.h>
23 #include <linux/tty_driver.h>
24 #include <linux/tty_flip.h>
25 #include <linux/uaccess.h>
26 #include <linux/usb.h>
27 #include <linux/usb/serial.h>
28 #include <asm/unaligned.h>
29
30 /* Definitions for the vendor ID and device ID */
31 #define MX_USBSERIAL_VID 0x110A
32 #define MX_UPORT1250_PID 0x1250
33 #define MX_UPORT1251_PID 0x1251
34 #define MX_UPORT1410_PID 0x1410
35 #define MX_UPORT1450_PID 0x1450
36 #define MX_UPORT1451_PID 0x1451
37 #define MX_UPORT1618_PID 0x1618
38 #define MX_UPORT1658_PID 0x1658
39 #define MX_UPORT1613_PID 0x1613
40 #define MX_UPORT1653_PID 0x1653
41
42 /* Definitions for USB info */
43 #define HEADER_SIZE 4
44 #define EVENT_LENGTH 8
45 #define DOWN_BLOCK_SIZE 64
46
47 /* Definitions for firmware info */
48 #define VER_ADDR_1 0x20
49 #define VER_ADDR_2 0x24
50 #define VER_ADDR_3 0x28
51
52 /* Definitions for USB vendor request */
53 #define RQ_VENDOR_NONE 0x00
54 #define RQ_VENDOR_SET_BAUD 0x01 /* Set baud rate */
55 #define RQ_VENDOR_SET_LINE 0x02 /* Set line status */
56 #define RQ_VENDOR_SET_CHARS 0x03 /* Set Xon/Xoff chars */
57 #define RQ_VENDOR_SET_RTS 0x04 /* Set RTS */
58 #define RQ_VENDOR_SET_DTR 0x05 /* Set DTR */
59 #define RQ_VENDOR_SET_XONXOFF 0x06 /* Set auto Xon/Xoff */
60 #define RQ_VENDOR_SET_RX_HOST_EN 0x07 /* Set RX host enable */
61 #define RQ_VENDOR_SET_OPEN 0x08 /* Set open/close port */
62 #define RQ_VENDOR_PURGE 0x09 /* Purge Rx/Tx buffer */
63 #define RQ_VENDOR_SET_MCR 0x0A /* Set MCR register */
64 #define RQ_VENDOR_SET_BREAK 0x0B /* Set Break signal */
65
66 #define RQ_VENDOR_START_FW_DOWN 0x0C /* Start firmware download */
67 #define RQ_VENDOR_STOP_FW_DOWN 0x0D /* Stop firmware download */
68 #define RQ_VENDOR_QUERY_FW_READY 0x0E /* Query if new firmware ready */
69
70 #define RQ_VENDOR_SET_FIFO_DISABLE 0x0F /* Set fifo disable */
71 #define RQ_VENDOR_SET_INTERFACE 0x10 /* Set interface */
72 #define RQ_VENDOR_SET_HIGH_PERFOR 0x11 /* Set hi-performance */
73
74 #define RQ_VENDOR_ERASE_BLOCK 0x12 /* Erase flash block */
75 #define RQ_VENDOR_WRITE_PAGE 0x13 /* Write flash page */
76 #define RQ_VENDOR_PREPARE_WRITE 0x14 /* Prepare write flash */
77 #define RQ_VENDOR_CONFIRM_WRITE 0x15 /* Confirm write flash */
78 #define RQ_VENDOR_LOCATE 0x16 /* Locate the device */
79
80 #define RQ_VENDOR_START_ROM_DOWN 0x17 /* Start firmware download */
81 #define RQ_VENDOR_ROM_DATA 0x18 /* Rom file data */
82 #define RQ_VENDOR_STOP_ROM_DOWN 0x19 /* Stop firmware download */
83 #define RQ_VENDOR_FW_DATA 0x20 /* Firmware data */
84
85 #define RQ_VENDOR_RESET_DEVICE 0x23 /* Try to reset the device */
86 #define RQ_VENDOR_QUERY_FW_CONFIG 0x24
87
88 #define RQ_VENDOR_GET_VERSION 0x81 /* Get firmware version */
89 #define RQ_VENDOR_GET_PAGE 0x82 /* Read flash page */
90 #define RQ_VENDOR_GET_ROM_PROC 0x83 /* Get ROM process state */
91
92 #define RQ_VENDOR_GET_INQUEUE 0x84 /* Data in input buffer */
93 #define RQ_VENDOR_GET_OUTQUEUE 0x85 /* Data in output buffer */
94
95 #define RQ_VENDOR_GET_MSR 0x86 /* Get modem status register */
96
97 /* Definitions for UPort event type */
98 #define UPORT_EVENT_NONE 0 /* None */
99 #define UPORT_EVENT_TXBUF_THRESHOLD 1 /* Tx buffer threshold */
100 #define UPORT_EVENT_SEND_NEXT 2 /* Send next */
101 #define UPORT_EVENT_MSR 3 /* Modem status */
102 #define UPORT_EVENT_LSR 4 /* Line status */
103 #define UPORT_EVENT_MCR 5 /* Modem control */
104
105 /* Definitions for serial event type */
106 #define SERIAL_EV_CTS 0x0008 /* CTS changed state */
107 #define SERIAL_EV_DSR 0x0010 /* DSR changed state */
108 #define SERIAL_EV_RLSD 0x0020 /* RLSD changed state */
109
110 /* Definitions for modem control event type */
111 #define SERIAL_EV_XOFF 0x40 /* XOFF received */
112
113 /* Definitions for line control of communication */
114 #define MX_WORDLENGTH_5 5
115 #define MX_WORDLENGTH_6 6
116 #define MX_WORDLENGTH_7 7
117 #define MX_WORDLENGTH_8 8
118
119 #define MX_PARITY_NONE 0
120 #define MX_PARITY_ODD 1
121 #define MX_PARITY_EVEN 2
122 #define MX_PARITY_MARK 3
123 #define MX_PARITY_SPACE 4
124
125 #define MX_STOP_BITS_1 0
126 #define MX_STOP_BITS_1_5 1
127 #define MX_STOP_BITS_2 2
128
129 #define MX_RTS_DISABLE 0x0
130 #define MX_RTS_ENABLE 0x1
131 #define MX_RTS_HW 0x2
132 #define MX_RTS_NO_CHANGE 0x3 /* Flag, not valid register value*/
133
134 #define MX_INT_RS232 0
135 #define MX_INT_2W_RS485 1
136 #define MX_INT_RS422 2
137 #define MX_INT_4W_RS485 3
138
139 /* Definitions for holding reason */
140 #define MX_WAIT_FOR_CTS 0x0001
141 #define MX_WAIT_FOR_DSR 0x0002
142 #define MX_WAIT_FOR_DCD 0x0004
143 #define MX_WAIT_FOR_XON 0x0008
144 #define MX_WAIT_FOR_START_TX 0x0010
145 #define MX_WAIT_FOR_UNTHROTTLE 0x0020
146 #define MX_WAIT_FOR_LOW_WATER 0x0040
147 #define MX_WAIT_FOR_SEND_NEXT 0x0080
148
149 #define MX_UPORT_2_PORT BIT(0)
150 #define MX_UPORT_4_PORT BIT(1)
151 #define MX_UPORT_8_PORT BIT(2)
152 #define MX_UPORT_16_PORT BIT(3)
153
154 /* This structure holds all of the local port information */
155 struct mxuport_port {
156 u8 mcr_state; /* Last MCR state */
157 u8 msr_state; /* Last MSR state */
158 struct mutex mutex; /* Protects mcr_state */
159 spinlock_t spinlock; /* Protects msr_state */
160 };
161
162 /* Table of devices that work with this driver */
163 static const struct usb_device_id mxuport_idtable[] = {
164 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1250_PID),
165 .driver_info = MX_UPORT_2_PORT },
166 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1251_PID),
167 .driver_info = MX_UPORT_2_PORT },
168 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1410_PID),
169 .driver_info = MX_UPORT_4_PORT },
170 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1450_PID),
171 .driver_info = MX_UPORT_4_PORT },
172 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1451_PID),
173 .driver_info = MX_UPORT_4_PORT },
174 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1618_PID),
175 .driver_info = MX_UPORT_8_PORT },
176 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1658_PID),
177 .driver_info = MX_UPORT_8_PORT },
178 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1613_PID),
179 .driver_info = MX_UPORT_16_PORT },
180 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1653_PID),
181 .driver_info = MX_UPORT_16_PORT },
182 {} /* Terminating entry */
183 };
184
185 MODULE_DEVICE_TABLE(usb, mxuport_idtable);
186
187 /*
188 * Add a four byte header containing the port number and the number of
189 * bytes of data in the message. Return the number of bytes in the
190 * buffer.
191 */
mxuport_prepare_write_buffer(struct usb_serial_port * port,void * dest,size_t size)192 static int mxuport_prepare_write_buffer(struct usb_serial_port *port,
193 void *dest, size_t size)
194 {
195 u8 *buf = dest;
196 int count;
197
198 count = kfifo_out_locked(&port->write_fifo, buf + HEADER_SIZE,
199 size - HEADER_SIZE,
200 &port->lock);
201
202 put_unaligned_be16(port->port_number, buf);
203 put_unaligned_be16(count, buf + 2);
204
205 dev_dbg(&port->dev, "%s - size %zd count %d\n", __func__,
206 size, count);
207
208 return count + HEADER_SIZE;
209 }
210
211 /* Read the given buffer in from the control pipe. */
mxuport_recv_ctrl_urb(struct usb_serial * serial,u8 request,u16 value,u16 index,u8 * data,size_t size)212 static int mxuport_recv_ctrl_urb(struct usb_serial *serial,
213 u8 request, u16 value, u16 index,
214 u8 *data, size_t size)
215 {
216 int status;
217
218 status = usb_control_msg(serial->dev,
219 usb_rcvctrlpipe(serial->dev, 0),
220 request,
221 (USB_DIR_IN | USB_TYPE_VENDOR |
222 USB_RECIP_DEVICE), value, index,
223 data, size,
224 USB_CTRL_GET_TIMEOUT);
225 if (status < 0) {
226 dev_err(&serial->interface->dev,
227 "%s - usb_control_msg failed (%d)\n",
228 __func__, status);
229 return status;
230 }
231
232 if (status != size) {
233 dev_err(&serial->interface->dev,
234 "%s - short read (%d / %zd)\n",
235 __func__, status, size);
236 return -EIO;
237 }
238
239 return status;
240 }
241
242 /* Write the given buffer out to the control pipe. */
mxuport_send_ctrl_data_urb(struct usb_serial * serial,u8 request,u16 value,u16 index,u8 * data,size_t size)243 static int mxuport_send_ctrl_data_urb(struct usb_serial *serial,
244 u8 request,
245 u16 value, u16 index,
246 u8 *data, size_t size)
247 {
248 int status;
249
250 status = usb_control_msg(serial->dev,
251 usb_sndctrlpipe(serial->dev, 0),
252 request,
253 (USB_DIR_OUT | USB_TYPE_VENDOR |
254 USB_RECIP_DEVICE), value, index,
255 data, size,
256 USB_CTRL_SET_TIMEOUT);
257 if (status < 0) {
258 dev_err(&serial->interface->dev,
259 "%s - usb_control_msg failed (%d)\n",
260 __func__, status);
261 return status;
262 }
263
264 if (status != size) {
265 dev_err(&serial->interface->dev,
266 "%s - short write (%d / %zd)\n",
267 __func__, status, size);
268 return -EIO;
269 }
270
271 return 0;
272 }
273
274 /* Send a vendor request without any data */
mxuport_send_ctrl_urb(struct usb_serial * serial,u8 request,u16 value,u16 index)275 static int mxuport_send_ctrl_urb(struct usb_serial *serial,
276 u8 request, u16 value, u16 index)
277 {
278 return mxuport_send_ctrl_data_urb(serial, request, value, index,
279 NULL, 0);
280 }
281
282 /*
283 * mxuport_throttle - throttle function of driver
284 *
285 * This function is called by the tty driver when it wants to stop the
286 * data being read from the port. Since all the data comes over one
287 * bulk in endpoint, we cannot stop submitting urbs by setting
288 * port->throttle. Instead tell the device to stop sending us data for
289 * the port.
290 */
mxuport_throttle(struct tty_struct * tty)291 static void mxuport_throttle(struct tty_struct *tty)
292 {
293 struct usb_serial_port *port = tty->driver_data;
294 struct usb_serial *serial = port->serial;
295
296 dev_dbg(&port->dev, "%s\n", __func__);
297
298 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
299 0, port->port_number);
300 }
301
302 /*
303 * mxuport_unthrottle - unthrottle function of driver
304 *
305 * This function is called by the tty driver when it wants to resume
306 * the data being read from the port. Tell the device it can resume
307 * sending us received data from the port.
308 */
mxuport_unthrottle(struct tty_struct * tty)309 static void mxuport_unthrottle(struct tty_struct *tty)
310 {
311
312 struct usb_serial_port *port = tty->driver_data;
313 struct usb_serial *serial = port->serial;
314
315 dev_dbg(&port->dev, "%s\n", __func__);
316
317 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
318 1, port->port_number);
319 }
320
321 /*
322 * Processes one chunk of data received for a port. Mostly a copy of
323 * usb_serial_generic_process_read_urb().
324 */
mxuport_process_read_urb_data(struct usb_serial_port * port,char * data,int size)325 static void mxuport_process_read_urb_data(struct usb_serial_port *port,
326 char *data, int size)
327 {
328 int i;
329
330 if (port->sysrq) {
331 for (i = 0; i < size; i++, data++) {
332 if (!usb_serial_handle_sysrq_char(port, *data))
333 tty_insert_flip_char(&port->port, *data,
334 TTY_NORMAL);
335 }
336 } else {
337 tty_insert_flip_string(&port->port, data, size);
338 }
339 tty_flip_buffer_push(&port->port);
340 }
341
mxuport_msr_event(struct usb_serial_port * port,u8 buf[4])342 static void mxuport_msr_event(struct usb_serial_port *port, u8 buf[4])
343 {
344 struct mxuport_port *mxport = usb_get_serial_port_data(port);
345 u8 rcv_msr_hold = buf[2] & 0xF0;
346 u16 rcv_msr_event = get_unaligned_be16(buf);
347 unsigned long flags;
348
349 if (rcv_msr_event == 0)
350 return;
351
352 /* Update MSR status */
353 spin_lock_irqsave(&mxport->spinlock, flags);
354
355 dev_dbg(&port->dev, "%s - current MSR status = 0x%x\n",
356 __func__, mxport->msr_state);
357
358 if (rcv_msr_hold & UART_MSR_CTS) {
359 mxport->msr_state |= UART_MSR_CTS;
360 dev_dbg(&port->dev, "%s - CTS high\n", __func__);
361 } else {
362 mxport->msr_state &= ~UART_MSR_CTS;
363 dev_dbg(&port->dev, "%s - CTS low\n", __func__);
364 }
365
366 if (rcv_msr_hold & UART_MSR_DSR) {
367 mxport->msr_state |= UART_MSR_DSR;
368 dev_dbg(&port->dev, "%s - DSR high\n", __func__);
369 } else {
370 mxport->msr_state &= ~UART_MSR_DSR;
371 dev_dbg(&port->dev, "%s - DSR low\n", __func__);
372 }
373
374 if (rcv_msr_hold & UART_MSR_DCD) {
375 mxport->msr_state |= UART_MSR_DCD;
376 dev_dbg(&port->dev, "%s - DCD high\n", __func__);
377 } else {
378 mxport->msr_state &= ~UART_MSR_DCD;
379 dev_dbg(&port->dev, "%s - DCD low\n", __func__);
380 }
381 spin_unlock_irqrestore(&mxport->spinlock, flags);
382
383 if (rcv_msr_event &
384 (SERIAL_EV_CTS | SERIAL_EV_DSR | SERIAL_EV_RLSD)) {
385
386 if (rcv_msr_event & SERIAL_EV_CTS) {
387 port->icount.cts++;
388 dev_dbg(&port->dev, "%s - CTS change\n", __func__);
389 }
390
391 if (rcv_msr_event & SERIAL_EV_DSR) {
392 port->icount.dsr++;
393 dev_dbg(&port->dev, "%s - DSR change\n", __func__);
394 }
395
396 if (rcv_msr_event & SERIAL_EV_RLSD) {
397 port->icount.dcd++;
398 dev_dbg(&port->dev, "%s - DCD change\n", __func__);
399 }
400 wake_up_interruptible(&port->port.delta_msr_wait);
401 }
402 }
403
mxuport_lsr_event(struct usb_serial_port * port,u8 buf[4])404 static void mxuport_lsr_event(struct usb_serial_port *port, u8 buf[4])
405 {
406 u8 lsr_event = buf[2];
407
408 if (lsr_event & UART_LSR_BI) {
409 port->icount.brk++;
410 dev_dbg(&port->dev, "%s - break error\n", __func__);
411 }
412
413 if (lsr_event & UART_LSR_FE) {
414 port->icount.frame++;
415 dev_dbg(&port->dev, "%s - frame error\n", __func__);
416 }
417
418 if (lsr_event & UART_LSR_PE) {
419 port->icount.parity++;
420 dev_dbg(&port->dev, "%s - parity error\n", __func__);
421 }
422
423 if (lsr_event & UART_LSR_OE) {
424 port->icount.overrun++;
425 dev_dbg(&port->dev, "%s - overrun error\n", __func__);
426 }
427 }
428
429 /*
430 * When something interesting happens, modem control lines XON/XOFF
431 * etc, the device sends an event. Process these events.
432 */
mxuport_process_read_urb_event(struct usb_serial_port * port,u8 buf[4],u32 event)433 static void mxuport_process_read_urb_event(struct usb_serial_port *port,
434 u8 buf[4], u32 event)
435 {
436 dev_dbg(&port->dev, "%s - receive event : %04x\n", __func__, event);
437
438 switch (event) {
439 case UPORT_EVENT_SEND_NEXT:
440 /*
441 * Sent as part of the flow control on device buffers.
442 * Not currently used.
443 */
444 break;
445 case UPORT_EVENT_MSR:
446 mxuport_msr_event(port, buf);
447 break;
448 case UPORT_EVENT_LSR:
449 mxuport_lsr_event(port, buf);
450 break;
451 case UPORT_EVENT_MCR:
452 /*
453 * Event to indicate a change in XON/XOFF from the
454 * peer. Currently not used. We just continue
455 * sending the device data and it will buffer it if
456 * needed. This event could be used for flow control
457 * between the host and the device.
458 */
459 break;
460 default:
461 dev_dbg(&port->dev, "Unexpected event\n");
462 break;
463 }
464 }
465
466 /*
467 * One URB can contain data for multiple ports. Demultiplex the data,
468 * checking the port exists, is opened and the message is valid.
469 */
mxuport_process_read_urb_demux_data(struct urb * urb)470 static void mxuport_process_read_urb_demux_data(struct urb *urb)
471 {
472 struct usb_serial_port *port = urb->context;
473 struct usb_serial *serial = port->serial;
474 u8 *data = urb->transfer_buffer;
475 u8 *end = data + urb->actual_length;
476 struct usb_serial_port *demux_port;
477 u8 *ch;
478 u16 rcv_port;
479 u16 rcv_len;
480
481 while (data < end) {
482 if (data + HEADER_SIZE > end) {
483 dev_warn(&port->dev, "%s - message with short header\n",
484 __func__);
485 return;
486 }
487
488 rcv_port = get_unaligned_be16(data);
489 if (rcv_port >= serial->num_ports) {
490 dev_warn(&port->dev, "%s - message for invalid port\n",
491 __func__);
492 return;
493 }
494
495 demux_port = serial->port[rcv_port];
496 rcv_len = get_unaligned_be16(data + 2);
497 if (!rcv_len || data + HEADER_SIZE + rcv_len > end) {
498 dev_warn(&port->dev, "%s - short data\n", __func__);
499 return;
500 }
501
502 if (tty_port_initialized(&demux_port->port)) {
503 ch = data + HEADER_SIZE;
504 mxuport_process_read_urb_data(demux_port, ch, rcv_len);
505 } else {
506 dev_dbg(&demux_port->dev, "%s - data for closed port\n",
507 __func__);
508 }
509 data += HEADER_SIZE + rcv_len;
510 }
511 }
512
513 /*
514 * One URB can contain events for multiple ports. Demultiplex the event,
515 * checking the port exists, and is opened.
516 */
mxuport_process_read_urb_demux_event(struct urb * urb)517 static void mxuport_process_read_urb_demux_event(struct urb *urb)
518 {
519 struct usb_serial_port *port = urb->context;
520 struct usb_serial *serial = port->serial;
521 u8 *data = urb->transfer_buffer;
522 u8 *end = data + urb->actual_length;
523 struct usb_serial_port *demux_port;
524 u8 *ch;
525 u16 rcv_port;
526 u16 rcv_event;
527
528 while (data < end) {
529 if (data + EVENT_LENGTH > end) {
530 dev_warn(&port->dev, "%s - message with short event\n",
531 __func__);
532 return;
533 }
534
535 rcv_port = get_unaligned_be16(data);
536 if (rcv_port >= serial->num_ports) {
537 dev_warn(&port->dev, "%s - message for invalid port\n",
538 __func__);
539 return;
540 }
541
542 demux_port = serial->port[rcv_port];
543 if (tty_port_initialized(&demux_port->port)) {
544 ch = data + HEADER_SIZE;
545 rcv_event = get_unaligned_be16(data + 2);
546 mxuport_process_read_urb_event(demux_port, ch,
547 rcv_event);
548 } else {
549 dev_dbg(&demux_port->dev,
550 "%s - event for closed port\n", __func__);
551 }
552 data += EVENT_LENGTH;
553 }
554 }
555
556 /*
557 * This is called when we have received data on the bulk in
558 * endpoint. Depending on which port it was received on, it can
559 * contain serial data or events.
560 */
mxuport_process_read_urb(struct urb * urb)561 static void mxuport_process_read_urb(struct urb *urb)
562 {
563 struct usb_serial_port *port = urb->context;
564 struct usb_serial *serial = port->serial;
565
566 if (port == serial->port[0])
567 mxuport_process_read_urb_demux_data(urb);
568
569 if (port == serial->port[1])
570 mxuport_process_read_urb_demux_event(urb);
571 }
572
573 /*
574 * Ask the device how many bytes it has queued to be sent out. If
575 * there are none, return true.
576 */
mxuport_tx_empty(struct usb_serial_port * port)577 static bool mxuport_tx_empty(struct usb_serial_port *port)
578 {
579 struct usb_serial *serial = port->serial;
580 bool is_empty = true;
581 u32 txlen;
582 u8 *len_buf;
583 int err;
584
585 len_buf = kzalloc(4, GFP_KERNEL);
586 if (!len_buf)
587 goto out;
588
589 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_OUTQUEUE, 0,
590 port->port_number, len_buf, 4);
591 if (err < 0)
592 goto out;
593
594 txlen = get_unaligned_be32(len_buf);
595 dev_dbg(&port->dev, "%s - tx len = %u\n", __func__, txlen);
596
597 if (txlen != 0)
598 is_empty = false;
599
600 out:
601 kfree(len_buf);
602 return is_empty;
603 }
604
mxuport_set_mcr(struct usb_serial_port * port,u8 mcr_state)605 static int mxuport_set_mcr(struct usb_serial_port *port, u8 mcr_state)
606 {
607 struct usb_serial *serial = port->serial;
608 int err;
609
610 dev_dbg(&port->dev, "%s - %02x\n", __func__, mcr_state);
611
612 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_MCR,
613 mcr_state, port->port_number);
614 if (err)
615 dev_err(&port->dev, "%s - failed to change MCR\n", __func__);
616
617 return err;
618 }
619
mxuport_set_dtr(struct usb_serial_port * port,int on)620 static int mxuport_set_dtr(struct usb_serial_port *port, int on)
621 {
622 struct mxuport_port *mxport = usb_get_serial_port_data(port);
623 struct usb_serial *serial = port->serial;
624 int err;
625
626 mutex_lock(&mxport->mutex);
627
628 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_DTR,
629 !!on, port->port_number);
630 if (!err) {
631 if (on)
632 mxport->mcr_state |= UART_MCR_DTR;
633 else
634 mxport->mcr_state &= ~UART_MCR_DTR;
635 }
636
637 mutex_unlock(&mxport->mutex);
638
639 return err;
640 }
641
mxuport_set_rts(struct usb_serial_port * port,u8 state)642 static int mxuport_set_rts(struct usb_serial_port *port, u8 state)
643 {
644 struct mxuport_port *mxport = usb_get_serial_port_data(port);
645 struct usb_serial *serial = port->serial;
646 int err;
647 u8 mcr_state;
648
649 mutex_lock(&mxport->mutex);
650 mcr_state = mxport->mcr_state;
651
652 switch (state) {
653 case MX_RTS_DISABLE:
654 mcr_state &= ~UART_MCR_RTS;
655 break;
656 case MX_RTS_ENABLE:
657 mcr_state |= UART_MCR_RTS;
658 break;
659 case MX_RTS_HW:
660 /*
661 * Do not update mxport->mcr_state when doing hardware
662 * flow control.
663 */
664 break;
665 default:
666 /*
667 * Should not happen, but somebody might try passing
668 * MX_RTS_NO_CHANGE, which is not valid.
669 */
670 err = -EINVAL;
671 goto out;
672 }
673 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RTS,
674 state, port->port_number);
675 if (!err)
676 mxport->mcr_state = mcr_state;
677
678 out:
679 mutex_unlock(&mxport->mutex);
680
681 return err;
682 }
683
mxuport_dtr_rts(struct usb_serial_port * port,int on)684 static void mxuport_dtr_rts(struct usb_serial_port *port, int on)
685 {
686 struct mxuport_port *mxport = usb_get_serial_port_data(port);
687 u8 mcr_state;
688 int err;
689
690 mutex_lock(&mxport->mutex);
691 mcr_state = mxport->mcr_state;
692
693 if (on)
694 mcr_state |= (UART_MCR_RTS | UART_MCR_DTR);
695 else
696 mcr_state &= ~(UART_MCR_RTS | UART_MCR_DTR);
697
698 err = mxuport_set_mcr(port, mcr_state);
699 if (!err)
700 mxport->mcr_state = mcr_state;
701
702 mutex_unlock(&mxport->mutex);
703 }
704
mxuport_tiocmset(struct tty_struct * tty,unsigned int set,unsigned int clear)705 static int mxuport_tiocmset(struct tty_struct *tty, unsigned int set,
706 unsigned int clear)
707 {
708 struct usb_serial_port *port = tty->driver_data;
709 struct mxuport_port *mxport = usb_get_serial_port_data(port);
710 int err;
711 u8 mcr_state;
712
713 mutex_lock(&mxport->mutex);
714 mcr_state = mxport->mcr_state;
715
716 if (set & TIOCM_RTS)
717 mcr_state |= UART_MCR_RTS;
718
719 if (set & TIOCM_DTR)
720 mcr_state |= UART_MCR_DTR;
721
722 if (clear & TIOCM_RTS)
723 mcr_state &= ~UART_MCR_RTS;
724
725 if (clear & TIOCM_DTR)
726 mcr_state &= ~UART_MCR_DTR;
727
728 err = mxuport_set_mcr(port, mcr_state);
729 if (!err)
730 mxport->mcr_state = mcr_state;
731
732 mutex_unlock(&mxport->mutex);
733
734 return err;
735 }
736
mxuport_tiocmget(struct tty_struct * tty)737 static int mxuport_tiocmget(struct tty_struct *tty)
738 {
739 struct mxuport_port *mxport;
740 struct usb_serial_port *port = tty->driver_data;
741 unsigned int result;
742 unsigned long flags;
743 unsigned int msr;
744 unsigned int mcr;
745
746 mxport = usb_get_serial_port_data(port);
747
748 mutex_lock(&mxport->mutex);
749 spin_lock_irqsave(&mxport->spinlock, flags);
750
751 msr = mxport->msr_state;
752 mcr = mxport->mcr_state;
753
754 spin_unlock_irqrestore(&mxport->spinlock, flags);
755 mutex_unlock(&mxport->mutex);
756
757 result = (((mcr & UART_MCR_DTR) ? TIOCM_DTR : 0) | /* 0x002 */
758 ((mcr & UART_MCR_RTS) ? TIOCM_RTS : 0) | /* 0x004 */
759 ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0) | /* 0x020 */
760 ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) | /* 0x040 */
761 ((msr & UART_MSR_RI) ? TIOCM_RI : 0) | /* 0x080 */
762 ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0)); /* 0x100 */
763
764 dev_dbg(&port->dev, "%s - 0x%04x\n", __func__, result);
765
766 return result;
767 }
768
mxuport_set_termios_flow(struct tty_struct * tty,struct ktermios * old_termios,struct usb_serial_port * port,struct usb_serial * serial)769 static int mxuport_set_termios_flow(struct tty_struct *tty,
770 struct ktermios *old_termios,
771 struct usb_serial_port *port,
772 struct usb_serial *serial)
773 {
774 u8 xon = START_CHAR(tty);
775 u8 xoff = STOP_CHAR(tty);
776 int enable;
777 int err;
778 u8 *buf;
779 u8 rts;
780
781 buf = kmalloc(2, GFP_KERNEL);
782 if (!buf)
783 return -ENOMEM;
784
785 /* S/W flow control settings */
786 if (I_IXOFF(tty) || I_IXON(tty)) {
787 enable = 1;
788 buf[0] = xon;
789 buf[1] = xoff;
790
791 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_CHARS,
792 0, port->port_number,
793 buf, 2);
794 if (err)
795 goto out;
796
797 dev_dbg(&port->dev, "%s - XON = 0x%02x, XOFF = 0x%02x\n",
798 __func__, xon, xoff);
799 } else {
800 enable = 0;
801 }
802
803 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_XONXOFF,
804 enable, port->port_number);
805 if (err)
806 goto out;
807
808 rts = MX_RTS_NO_CHANGE;
809
810 /* H/W flow control settings */
811 if (!old_termios ||
812 C_CRTSCTS(tty) != (old_termios->c_cflag & CRTSCTS)) {
813 if (C_CRTSCTS(tty))
814 rts = MX_RTS_HW;
815 else
816 rts = MX_RTS_ENABLE;
817 }
818
819 if (C_BAUD(tty)) {
820 if (old_termios && (old_termios->c_cflag & CBAUD) == B0) {
821 /* Raise DTR and RTS */
822 if (C_CRTSCTS(tty))
823 rts = MX_RTS_HW;
824 else
825 rts = MX_RTS_ENABLE;
826 mxuport_set_dtr(port, 1);
827 }
828 } else {
829 /* Drop DTR and RTS */
830 rts = MX_RTS_DISABLE;
831 mxuport_set_dtr(port, 0);
832 }
833
834 if (rts != MX_RTS_NO_CHANGE)
835 err = mxuport_set_rts(port, rts);
836
837 out:
838 kfree(buf);
839 return err;
840 }
841
mxuport_set_termios(struct tty_struct * tty,struct usb_serial_port * port,struct ktermios * old_termios)842 static void mxuport_set_termios(struct tty_struct *tty,
843 struct usb_serial_port *port,
844 struct ktermios *old_termios)
845 {
846 struct usb_serial *serial = port->serial;
847 u8 *buf;
848 u8 data_bits;
849 u8 stop_bits;
850 u8 parity;
851 int baud;
852 int err;
853
854 if (old_termios &&
855 !tty_termios_hw_change(&tty->termios, old_termios) &&
856 tty->termios.c_iflag == old_termios->c_iflag) {
857 dev_dbg(&port->dev, "%s - nothing to change\n", __func__);
858 return;
859 }
860
861 buf = kmalloc(4, GFP_KERNEL);
862 if (!buf)
863 return;
864
865 /* Set data bit of termios */
866 switch (C_CSIZE(tty)) {
867 case CS5:
868 data_bits = MX_WORDLENGTH_5;
869 break;
870 case CS6:
871 data_bits = MX_WORDLENGTH_6;
872 break;
873 case CS7:
874 data_bits = MX_WORDLENGTH_7;
875 break;
876 case CS8:
877 default:
878 data_bits = MX_WORDLENGTH_8;
879 break;
880 }
881
882 /* Set parity of termios */
883 if (C_PARENB(tty)) {
884 if (C_CMSPAR(tty)) {
885 if (C_PARODD(tty))
886 parity = MX_PARITY_MARK;
887 else
888 parity = MX_PARITY_SPACE;
889 } else {
890 if (C_PARODD(tty))
891 parity = MX_PARITY_ODD;
892 else
893 parity = MX_PARITY_EVEN;
894 }
895 } else {
896 parity = MX_PARITY_NONE;
897 }
898
899 /* Set stop bit of termios */
900 if (C_CSTOPB(tty))
901 stop_bits = MX_STOP_BITS_2;
902 else
903 stop_bits = MX_STOP_BITS_1;
904
905 buf[0] = data_bits;
906 buf[1] = parity;
907 buf[2] = stop_bits;
908 buf[3] = 0;
909
910 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_LINE,
911 0, port->port_number, buf, 4);
912 if (err)
913 goto out;
914
915 err = mxuport_set_termios_flow(tty, old_termios, port, serial);
916 if (err)
917 goto out;
918
919 baud = tty_get_baud_rate(tty);
920 if (!baud)
921 baud = 9600;
922
923 /* Note: Little Endian */
924 put_unaligned_le32(baud, buf);
925
926 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_BAUD,
927 0, port->port_number,
928 buf, 4);
929 if (err)
930 goto out;
931
932 dev_dbg(&port->dev, "baud_rate : %d\n", baud);
933 dev_dbg(&port->dev, "data_bits : %d\n", data_bits);
934 dev_dbg(&port->dev, "parity : %d\n", parity);
935 dev_dbg(&port->dev, "stop_bits : %d\n", stop_bits);
936
937 out:
938 kfree(buf);
939 }
940
941 /*
942 * Determine how many ports this device has dynamically. It will be
943 * called after the probe() callback is called, but before attach().
944 */
mxuport_calc_num_ports(struct usb_serial * serial,struct usb_serial_endpoints * epds)945 static int mxuport_calc_num_ports(struct usb_serial *serial,
946 struct usb_serial_endpoints *epds)
947 {
948 unsigned long features = (unsigned long)usb_get_serial_data(serial);
949 int num_ports;
950 int i;
951
952 if (features & MX_UPORT_2_PORT) {
953 num_ports = 2;
954 } else if (features & MX_UPORT_4_PORT) {
955 num_ports = 4;
956 } else if (features & MX_UPORT_8_PORT) {
957 num_ports = 8;
958 } else if (features & MX_UPORT_16_PORT) {
959 num_ports = 16;
960 } else {
961 dev_warn(&serial->interface->dev,
962 "unknown device, assuming two ports\n");
963 num_ports = 2;
964 }
965
966 /*
967 * Setup bulk-out endpoint multiplexing. All ports share the same
968 * bulk-out endpoint.
969 */
970 BUILD_BUG_ON(ARRAY_SIZE(epds->bulk_out) < 16);
971
972 for (i = 1; i < num_ports; ++i)
973 epds->bulk_out[i] = epds->bulk_out[0];
974
975 epds->num_bulk_out = num_ports;
976
977 return num_ports;
978 }
979
980 /* Get the version of the firmware currently running. */
mxuport_get_fw_version(struct usb_serial * serial,u32 * version)981 static int mxuport_get_fw_version(struct usb_serial *serial, u32 *version)
982 {
983 u8 *ver_buf;
984 int err;
985
986 ver_buf = kzalloc(4, GFP_KERNEL);
987 if (!ver_buf)
988 return -ENOMEM;
989
990 /* Get firmware version from SDRAM */
991 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_VERSION, 0, 0,
992 ver_buf, 4);
993 if (err != 4) {
994 err = -EIO;
995 goto out;
996 }
997
998 *version = (ver_buf[0] << 16) | (ver_buf[1] << 8) | ver_buf[2];
999 err = 0;
1000 out:
1001 kfree(ver_buf);
1002 return err;
1003 }
1004
1005 /* Given a firmware blob, download it to the device. */
mxuport_download_fw(struct usb_serial * serial,const struct firmware * fw_p)1006 static int mxuport_download_fw(struct usb_serial *serial,
1007 const struct firmware *fw_p)
1008 {
1009 u8 *fw_buf;
1010 size_t txlen;
1011 size_t fwidx;
1012 int err;
1013
1014 fw_buf = kmalloc(DOWN_BLOCK_SIZE, GFP_KERNEL);
1015 if (!fw_buf)
1016 return -ENOMEM;
1017
1018 dev_dbg(&serial->interface->dev, "Starting firmware download...\n");
1019 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_START_FW_DOWN, 0, 0);
1020 if (err)
1021 goto out;
1022
1023 fwidx = 0;
1024 do {
1025 txlen = min_t(size_t, (fw_p->size - fwidx), DOWN_BLOCK_SIZE);
1026
1027 memcpy(fw_buf, &fw_p->data[fwidx], txlen);
1028 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_FW_DATA,
1029 0, 0, fw_buf, txlen);
1030 if (err) {
1031 mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN,
1032 0, 0);
1033 goto out;
1034 }
1035
1036 fwidx += txlen;
1037 usleep_range(1000, 2000);
1038
1039 } while (fwidx < fw_p->size);
1040
1041 msleep(1000);
1042 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, 0, 0);
1043 if (err)
1044 goto out;
1045
1046 msleep(1000);
1047 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_READY, 0, 0);
1048
1049 out:
1050 kfree(fw_buf);
1051 return err;
1052 }
1053
mxuport_probe(struct usb_serial * serial,const struct usb_device_id * id)1054 static int mxuport_probe(struct usb_serial *serial,
1055 const struct usb_device_id *id)
1056 {
1057 u16 productid = le16_to_cpu(serial->dev->descriptor.idProduct);
1058 const struct firmware *fw_p = NULL;
1059 u32 version;
1060 int local_ver;
1061 char buf[32];
1062 int err;
1063
1064 /* Load our firmware */
1065 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_CONFIG, 0, 0);
1066 if (err) {
1067 mxuport_send_ctrl_urb(serial, RQ_VENDOR_RESET_DEVICE, 0, 0);
1068 return err;
1069 }
1070
1071 err = mxuport_get_fw_version(serial, &version);
1072 if (err < 0)
1073 return err;
1074
1075 dev_dbg(&serial->interface->dev, "Device firmware version v%x.%x.%x\n",
1076 (version & 0xff0000) >> 16,
1077 (version & 0xff00) >> 8,
1078 (version & 0xff));
1079
1080 snprintf(buf, sizeof(buf) - 1, "moxa/moxa-%04x.fw", productid);
1081
1082 err = request_firmware(&fw_p, buf, &serial->interface->dev);
1083 if (err) {
1084 dev_warn(&serial->interface->dev, "Firmware %s not found\n",
1085 buf);
1086
1087 /* Use the firmware already in the device */
1088 err = 0;
1089 } else {
1090 local_ver = ((fw_p->data[VER_ADDR_1] << 16) |
1091 (fw_p->data[VER_ADDR_2] << 8) |
1092 fw_p->data[VER_ADDR_3]);
1093 dev_dbg(&serial->interface->dev,
1094 "Available firmware version v%x.%x.%x\n",
1095 fw_p->data[VER_ADDR_1], fw_p->data[VER_ADDR_2],
1096 fw_p->data[VER_ADDR_3]);
1097 if (local_ver > version) {
1098 err = mxuport_download_fw(serial, fw_p);
1099 if (err)
1100 goto out;
1101 err = mxuport_get_fw_version(serial, &version);
1102 if (err < 0)
1103 goto out;
1104 }
1105 }
1106
1107 dev_info(&serial->interface->dev,
1108 "Using device firmware version v%x.%x.%x\n",
1109 (version & 0xff0000) >> 16,
1110 (version & 0xff00) >> 8,
1111 (version & 0xff));
1112
1113 /*
1114 * Contains the features of this hardware. Store away for
1115 * later use, eg, number of ports.
1116 */
1117 usb_set_serial_data(serial, (void *)id->driver_info);
1118 out:
1119 if (fw_p)
1120 release_firmware(fw_p);
1121 return err;
1122 }
1123
1124
mxuport_port_probe(struct usb_serial_port * port)1125 static int mxuport_port_probe(struct usb_serial_port *port)
1126 {
1127 struct usb_serial *serial = port->serial;
1128 struct mxuport_port *mxport;
1129 int err;
1130
1131 mxport = devm_kzalloc(&port->dev, sizeof(struct mxuport_port),
1132 GFP_KERNEL);
1133 if (!mxport)
1134 return -ENOMEM;
1135
1136 mutex_init(&mxport->mutex);
1137 spin_lock_init(&mxport->spinlock);
1138
1139 /* Set the port private data */
1140 usb_set_serial_port_data(port, mxport);
1141
1142 /* Set FIFO (Enable) */
1143 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_FIFO_DISABLE,
1144 0, port->port_number);
1145 if (err)
1146 return err;
1147
1148 /* Set transmission mode (Hi-Performance) */
1149 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_HIGH_PERFOR,
1150 0, port->port_number);
1151 if (err)
1152 return err;
1153
1154 /* Set interface (RS-232) */
1155 return mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_INTERFACE,
1156 MX_INT_RS232,
1157 port->port_number);
1158 }
1159
mxuport_attach(struct usb_serial * serial)1160 static int mxuport_attach(struct usb_serial *serial)
1161 {
1162 struct usb_serial_port *port0 = serial->port[0];
1163 struct usb_serial_port *port1 = serial->port[1];
1164 int err;
1165
1166 /*
1167 * All data from the ports is received on the first bulk in
1168 * endpoint, with a multiplex header. The second bulk in is
1169 * used for events.
1170 *
1171 * Start to read from the device.
1172 */
1173 err = usb_serial_generic_submit_read_urbs(port0, GFP_KERNEL);
1174 if (err)
1175 return err;
1176
1177 err = usb_serial_generic_submit_read_urbs(port1, GFP_KERNEL);
1178 if (err) {
1179 usb_serial_generic_close(port0);
1180 return err;
1181 }
1182
1183 return 0;
1184 }
1185
mxuport_release(struct usb_serial * serial)1186 static void mxuport_release(struct usb_serial *serial)
1187 {
1188 struct usb_serial_port *port0 = serial->port[0];
1189 struct usb_serial_port *port1 = serial->port[1];
1190
1191 usb_serial_generic_close(port1);
1192 usb_serial_generic_close(port0);
1193 }
1194
mxuport_open(struct tty_struct * tty,struct usb_serial_port * port)1195 static int mxuport_open(struct tty_struct *tty, struct usb_serial_port *port)
1196 {
1197 struct mxuport_port *mxport = usb_get_serial_port_data(port);
1198 struct usb_serial *serial = port->serial;
1199 int err;
1200
1201 /* Set receive host (enable) */
1202 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
1203 1, port->port_number);
1204 if (err)
1205 return err;
1206
1207 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN,
1208 1, port->port_number);
1209 if (err) {
1210 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
1211 0, port->port_number);
1212 return err;
1213 }
1214
1215 /* Initial port termios */
1216 if (tty)
1217 mxuport_set_termios(tty, port, NULL);
1218
1219 /*
1220 * TODO: use RQ_VENDOR_GET_MSR, once we know what it
1221 * returns.
1222 */
1223 mxport->msr_state = 0;
1224
1225 return err;
1226 }
1227
mxuport_close(struct usb_serial_port * port)1228 static void mxuport_close(struct usb_serial_port *port)
1229 {
1230 struct usb_serial *serial = port->serial;
1231
1232 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, 0,
1233 port->port_number);
1234
1235 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 0,
1236 port->port_number);
1237 }
1238
1239 /* Send a break to the port. */
mxuport_break_ctl(struct tty_struct * tty,int break_state)1240 static void mxuport_break_ctl(struct tty_struct *tty, int break_state)
1241 {
1242 struct usb_serial_port *port = tty->driver_data;
1243 struct usb_serial *serial = port->serial;
1244 int enable;
1245
1246 if (break_state == -1) {
1247 enable = 1;
1248 dev_dbg(&port->dev, "%s - sending break\n", __func__);
1249 } else {
1250 enable = 0;
1251 dev_dbg(&port->dev, "%s - clearing break\n", __func__);
1252 }
1253
1254 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_BREAK,
1255 enable, port->port_number);
1256 }
1257
mxuport_resume(struct usb_serial * serial)1258 static int mxuport_resume(struct usb_serial *serial)
1259 {
1260 struct usb_serial_port *port;
1261 int c = 0;
1262 int i;
1263 int r;
1264
1265 for (i = 0; i < 2; i++) {
1266 port = serial->port[i];
1267
1268 r = usb_serial_generic_submit_read_urbs(port, GFP_NOIO);
1269 if (r < 0)
1270 c++;
1271 }
1272
1273 for (i = 0; i < serial->num_ports; i++) {
1274 port = serial->port[i];
1275 if (!tty_port_initialized(&port->port))
1276 continue;
1277
1278 r = usb_serial_generic_write_start(port, GFP_NOIO);
1279 if (r < 0)
1280 c++;
1281 }
1282
1283 return c ? -EIO : 0;
1284 }
1285
1286 static struct usb_serial_driver mxuport_device = {
1287 .driver = {
1288 .owner = THIS_MODULE,
1289 .name = "mxuport",
1290 },
1291 .description = "MOXA UPort",
1292 .id_table = mxuport_idtable,
1293 .num_bulk_in = 2,
1294 .num_bulk_out = 1,
1295 .probe = mxuport_probe,
1296 .port_probe = mxuport_port_probe,
1297 .attach = mxuport_attach,
1298 .release = mxuport_release,
1299 .calc_num_ports = mxuport_calc_num_ports,
1300 .open = mxuport_open,
1301 .close = mxuport_close,
1302 .set_termios = mxuport_set_termios,
1303 .break_ctl = mxuport_break_ctl,
1304 .tx_empty = mxuport_tx_empty,
1305 .tiocmiwait = usb_serial_generic_tiocmiwait,
1306 .get_icount = usb_serial_generic_get_icount,
1307 .throttle = mxuport_throttle,
1308 .unthrottle = mxuport_unthrottle,
1309 .tiocmget = mxuport_tiocmget,
1310 .tiocmset = mxuport_tiocmset,
1311 .dtr_rts = mxuport_dtr_rts,
1312 .process_read_urb = mxuport_process_read_urb,
1313 .prepare_write_buffer = mxuport_prepare_write_buffer,
1314 .resume = mxuport_resume,
1315 };
1316
1317 static struct usb_serial_driver *const serial_drivers[] = {
1318 &mxuport_device, NULL
1319 };
1320
1321 module_usb_serial_driver(serial_drivers, mxuport_idtable);
1322
1323 MODULE_AUTHOR("Andrew Lunn <andrew@lunn.ch>");
1324 MODULE_AUTHOR("<support@moxa.com>");
1325 MODULE_LICENSE("GPL");
1326