1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Driver for the NXP SAA7164 PCIe bridge
4 *
5 * Copyright (c) 2010-2015 Steven Toth <stoth@kernellabs.com>
6 */
7
8 #include <linux/init.h>
9 #include <linux/module.h>
10 #include <linux/pci.h>
11 #include <linux/delay.h>
12
13 #include "saa7164.h"
14
15 /* The Bridge API needs to understand register widths (in bytes) for the
16 * attached I2C devices, so we can simplify the virtual i2c mechansms
17 * and keep the -i2c.c implementation clean.
18 */
19 #define REGLEN_0bit 0
20 #define REGLEN_8bit 1
21 #define REGLEN_16bit 2
22
23 struct saa7164_board saa7164_boards[] = {
24 [SAA7164_BOARD_UNKNOWN] = {
25 /* Bridge will not load any firmware, without knowing
26 * the rev this would be fatal. */
27 .name = "Unknown",
28 },
29 [SAA7164_BOARD_UNKNOWN_REV2] = {
30 /* Bridge will load the v2 f/w and dump descriptors */
31 /* Required during new board bringup */
32 .name = "Generic Rev2",
33 .chiprev = SAA7164_CHIP_REV2,
34 },
35 [SAA7164_BOARD_UNKNOWN_REV3] = {
36 /* Bridge will load the v2 f/w and dump descriptors */
37 /* Required during new board bringup */
38 .name = "Generic Rev3",
39 .chiprev = SAA7164_CHIP_REV3,
40 },
41 [SAA7164_BOARD_HAUPPAUGE_HVR2200] = {
42 .name = "Hauppauge WinTV-HVR2200",
43 .porta = SAA7164_MPEG_DVB,
44 .portb = SAA7164_MPEG_DVB,
45 .portc = SAA7164_MPEG_ENCODER,
46 .portd = SAA7164_MPEG_ENCODER,
47 .porte = SAA7164_MPEG_VBI,
48 .portf = SAA7164_MPEG_VBI,
49 .chiprev = SAA7164_CHIP_REV3,
50 .unit = {{
51 .id = 0x1d,
52 .type = SAA7164_UNIT_EEPROM,
53 .name = "4K EEPROM",
54 .i2c_bus_nr = SAA7164_I2C_BUS_0,
55 .i2c_bus_addr = 0xa0 >> 1,
56 .i2c_reg_len = REGLEN_8bit,
57 }, {
58 .id = 0x04,
59 .type = SAA7164_UNIT_TUNER,
60 .name = "TDA18271-1",
61 .i2c_bus_nr = SAA7164_I2C_BUS_1,
62 .i2c_bus_addr = 0xc0 >> 1,
63 .i2c_reg_len = REGLEN_8bit,
64 }, {
65 .id = 0x1b,
66 .type = SAA7164_UNIT_TUNER,
67 .name = "TDA18271-2",
68 .i2c_bus_nr = SAA7164_I2C_BUS_2,
69 .i2c_bus_addr = 0xc0 >> 1,
70 .i2c_reg_len = REGLEN_8bit,
71 }, {
72 .id = 0x1e,
73 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
74 .name = "TDA10048-1",
75 .i2c_bus_nr = SAA7164_I2C_BUS_1,
76 .i2c_bus_addr = 0x10 >> 1,
77 .i2c_reg_len = REGLEN_8bit,
78 }, {
79 .id = 0x1f,
80 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
81 .name = "TDA10048-2",
82 .i2c_bus_nr = SAA7164_I2C_BUS_2,
83 .i2c_bus_addr = 0x12 >> 1,
84 .i2c_reg_len = REGLEN_8bit,
85 } },
86 },
87 [SAA7164_BOARD_HAUPPAUGE_HVR2200_2] = {
88 .name = "Hauppauge WinTV-HVR2200",
89 .porta = SAA7164_MPEG_DVB,
90 .portb = SAA7164_MPEG_DVB,
91 .portc = SAA7164_MPEG_ENCODER,
92 .portd = SAA7164_MPEG_ENCODER,
93 .porte = SAA7164_MPEG_VBI,
94 .portf = SAA7164_MPEG_VBI,
95 .chiprev = SAA7164_CHIP_REV2,
96 .unit = {{
97 .id = 0x06,
98 .type = SAA7164_UNIT_EEPROM,
99 .name = "4K EEPROM",
100 .i2c_bus_nr = SAA7164_I2C_BUS_0,
101 .i2c_bus_addr = 0xa0 >> 1,
102 .i2c_reg_len = REGLEN_8bit,
103 }, {
104 .id = 0x04,
105 .type = SAA7164_UNIT_TUNER,
106 .name = "TDA18271-1",
107 .i2c_bus_nr = SAA7164_I2C_BUS_1,
108 .i2c_bus_addr = 0xc0 >> 1,
109 .i2c_reg_len = REGLEN_8bit,
110 }, {
111 .id = 0x05,
112 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
113 .name = "TDA10048-1",
114 .i2c_bus_nr = SAA7164_I2C_BUS_1,
115 .i2c_bus_addr = 0x10 >> 1,
116 .i2c_reg_len = REGLEN_8bit,
117 }, {
118 .id = 0x1e,
119 .type = SAA7164_UNIT_TUNER,
120 .name = "TDA18271-2",
121 .i2c_bus_nr = SAA7164_I2C_BUS_2,
122 .i2c_bus_addr = 0xc0 >> 1,
123 .i2c_reg_len = REGLEN_8bit,
124 }, {
125 .id = 0x1f,
126 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
127 .name = "TDA10048-2",
128 .i2c_bus_nr = SAA7164_I2C_BUS_2,
129 .i2c_bus_addr = 0x12 >> 1,
130 .i2c_reg_len = REGLEN_8bit,
131 } },
132 },
133 [SAA7164_BOARD_HAUPPAUGE_HVR2200_3] = {
134 .name = "Hauppauge WinTV-HVR2200",
135 .porta = SAA7164_MPEG_DVB,
136 .portb = SAA7164_MPEG_DVB,
137 .portc = SAA7164_MPEG_ENCODER,
138 .portd = SAA7164_MPEG_ENCODER,
139 .porte = SAA7164_MPEG_VBI,
140 .portf = SAA7164_MPEG_VBI,
141 .chiprev = SAA7164_CHIP_REV2,
142 .unit = {{
143 .id = 0x1d,
144 .type = SAA7164_UNIT_EEPROM,
145 .name = "4K EEPROM",
146 .i2c_bus_nr = SAA7164_I2C_BUS_0,
147 .i2c_bus_addr = 0xa0 >> 1,
148 .i2c_reg_len = REGLEN_8bit,
149 }, {
150 .id = 0x04,
151 .type = SAA7164_UNIT_TUNER,
152 .name = "TDA18271-1",
153 .i2c_bus_nr = SAA7164_I2C_BUS_1,
154 .i2c_bus_addr = 0xc0 >> 1,
155 .i2c_reg_len = REGLEN_8bit,
156 }, {
157 .id = 0x05,
158 .type = SAA7164_UNIT_ANALOG_DEMODULATOR,
159 .name = "TDA8290-1",
160 .i2c_bus_nr = SAA7164_I2C_BUS_1,
161 .i2c_bus_addr = 0x84 >> 1,
162 .i2c_reg_len = REGLEN_8bit,
163 }, {
164 .id = 0x1b,
165 .type = SAA7164_UNIT_TUNER,
166 .name = "TDA18271-2",
167 .i2c_bus_nr = SAA7164_I2C_BUS_2,
168 .i2c_bus_addr = 0xc0 >> 1,
169 .i2c_reg_len = REGLEN_8bit,
170 }, {
171 .id = 0x1c,
172 .type = SAA7164_UNIT_ANALOG_DEMODULATOR,
173 .name = "TDA8290-2",
174 .i2c_bus_nr = SAA7164_I2C_BUS_2,
175 .i2c_bus_addr = 0x84 >> 1,
176 .i2c_reg_len = REGLEN_8bit,
177 }, {
178 .id = 0x1e,
179 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
180 .name = "TDA10048-1",
181 .i2c_bus_nr = SAA7164_I2C_BUS_1,
182 .i2c_bus_addr = 0x10 >> 1,
183 .i2c_reg_len = REGLEN_8bit,
184 }, {
185 .id = 0x1f,
186 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
187 .name = "TDA10048-2",
188 .i2c_bus_nr = SAA7164_I2C_BUS_2,
189 .i2c_bus_addr = 0x12 >> 1,
190 .i2c_reg_len = REGLEN_8bit,
191 } },
192 },
193 [SAA7164_BOARD_HAUPPAUGE_HVR2200_4] = {
194 .name = "Hauppauge WinTV-HVR2200",
195 .porta = SAA7164_MPEG_DVB,
196 .portb = SAA7164_MPEG_DVB,
197 .portc = SAA7164_MPEG_ENCODER,
198 .portd = SAA7164_MPEG_ENCODER,
199 .porte = SAA7164_MPEG_VBI,
200 .portf = SAA7164_MPEG_VBI,
201 .chiprev = SAA7164_CHIP_REV3,
202 .unit = {{
203 .id = 0x1d,
204 .type = SAA7164_UNIT_EEPROM,
205 .name = "4K EEPROM",
206 .i2c_bus_nr = SAA7164_I2C_BUS_0,
207 .i2c_bus_addr = 0xa0 >> 1,
208 .i2c_reg_len = REGLEN_8bit,
209 }, {
210 .id = 0x04,
211 .type = SAA7164_UNIT_TUNER,
212 .name = "TDA18271-1",
213 .i2c_bus_nr = SAA7164_I2C_BUS_1,
214 .i2c_bus_addr = 0xc0 >> 1,
215 .i2c_reg_len = REGLEN_8bit,
216 }, {
217 .id = 0x05,
218 .type = SAA7164_UNIT_ANALOG_DEMODULATOR,
219 .name = "TDA8290-1",
220 .i2c_bus_nr = SAA7164_I2C_BUS_1,
221 .i2c_bus_addr = 0x84 >> 1,
222 .i2c_reg_len = REGLEN_8bit,
223 }, {
224 .id = 0x1b,
225 .type = SAA7164_UNIT_TUNER,
226 .name = "TDA18271-2",
227 .i2c_bus_nr = SAA7164_I2C_BUS_2,
228 .i2c_bus_addr = 0xc0 >> 1,
229 .i2c_reg_len = REGLEN_8bit,
230 }, {
231 .id = 0x1c,
232 .type = SAA7164_UNIT_ANALOG_DEMODULATOR,
233 .name = "TDA8290-2",
234 .i2c_bus_nr = SAA7164_I2C_BUS_2,
235 .i2c_bus_addr = 0x84 >> 1,
236 .i2c_reg_len = REGLEN_8bit,
237 }, {
238 .id = 0x1e,
239 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
240 .name = "TDA10048-1",
241 .i2c_bus_nr = SAA7164_I2C_BUS_1,
242 .i2c_bus_addr = 0x10 >> 1,
243 .i2c_reg_len = REGLEN_8bit,
244 }, {
245 .id = 0x1f,
246 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
247 .name = "TDA10048-2",
248 .i2c_bus_nr = SAA7164_I2C_BUS_2,
249 .i2c_bus_addr = 0x12 >> 1,
250 .i2c_reg_len = REGLEN_8bit,
251 } },
252 },
253 [SAA7164_BOARD_HAUPPAUGE_HVR2250] = {
254 .name = "Hauppauge WinTV-HVR2250",
255 .porta = SAA7164_MPEG_DVB,
256 .portb = SAA7164_MPEG_DVB,
257 .portc = SAA7164_MPEG_ENCODER,
258 .portd = SAA7164_MPEG_ENCODER,
259 .porte = SAA7164_MPEG_VBI,
260 .portf = SAA7164_MPEG_VBI,
261 .chiprev = SAA7164_CHIP_REV3,
262 .unit = {{
263 .id = 0x22,
264 .type = SAA7164_UNIT_EEPROM,
265 .name = "4K EEPROM",
266 .i2c_bus_nr = SAA7164_I2C_BUS_0,
267 .i2c_bus_addr = 0xa0 >> 1,
268 .i2c_reg_len = REGLEN_8bit,
269 }, {
270 .id = 0x04,
271 .type = SAA7164_UNIT_TUNER,
272 .name = "TDA18271-1",
273 .i2c_bus_nr = SAA7164_I2C_BUS_1,
274 .i2c_bus_addr = 0xc0 >> 1,
275 .i2c_reg_len = REGLEN_8bit,
276 }, {
277 .id = 0x07,
278 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
279 .name = "CX24228/S5H1411-1 (TOP)",
280 .i2c_bus_nr = SAA7164_I2C_BUS_1,
281 .i2c_bus_addr = 0x32 >> 1,
282 .i2c_reg_len = REGLEN_8bit,
283 }, {
284 .id = 0x08,
285 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
286 .name = "CX24228/S5H1411-1 (QAM)",
287 .i2c_bus_nr = SAA7164_I2C_BUS_1,
288 .i2c_bus_addr = 0x34 >> 1,
289 .i2c_reg_len = REGLEN_8bit,
290 }, {
291 .id = 0x1e,
292 .type = SAA7164_UNIT_TUNER,
293 .name = "TDA18271-2",
294 .i2c_bus_nr = SAA7164_I2C_BUS_2,
295 .i2c_bus_addr = 0xc0 >> 1,
296 .i2c_reg_len = REGLEN_8bit,
297 }, {
298 .id = 0x20,
299 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
300 .name = "CX24228/S5H1411-2 (TOP)",
301 .i2c_bus_nr = SAA7164_I2C_BUS_2,
302 .i2c_bus_addr = 0x32 >> 1,
303 .i2c_reg_len = REGLEN_8bit,
304 }, {
305 .id = 0x23,
306 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
307 .name = "CX24228/S5H1411-2 (QAM)",
308 .i2c_bus_nr = SAA7164_I2C_BUS_2,
309 .i2c_bus_addr = 0x34 >> 1,
310 .i2c_reg_len = REGLEN_8bit,
311 } },
312 },
313 [SAA7164_BOARD_HAUPPAUGE_HVR2250_2] = {
314 .name = "Hauppauge WinTV-HVR2250",
315 .porta = SAA7164_MPEG_DVB,
316 .portb = SAA7164_MPEG_DVB,
317 .portc = SAA7164_MPEG_ENCODER,
318 .portd = SAA7164_MPEG_ENCODER,
319 .porte = SAA7164_MPEG_VBI,
320 .portf = SAA7164_MPEG_VBI,
321 .chiprev = SAA7164_CHIP_REV3,
322 .unit = {{
323 .id = 0x28,
324 .type = SAA7164_UNIT_EEPROM,
325 .name = "4K EEPROM",
326 .i2c_bus_nr = SAA7164_I2C_BUS_0,
327 .i2c_bus_addr = 0xa0 >> 1,
328 .i2c_reg_len = REGLEN_8bit,
329 }, {
330 .id = 0x04,
331 .type = SAA7164_UNIT_TUNER,
332 .name = "TDA18271-1",
333 .i2c_bus_nr = SAA7164_I2C_BUS_1,
334 .i2c_bus_addr = 0xc0 >> 1,
335 .i2c_reg_len = REGLEN_8bit,
336 }, {
337 .id = 0x07,
338 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
339 .name = "CX24228/S5H1411-1 (TOP)",
340 .i2c_bus_nr = SAA7164_I2C_BUS_1,
341 .i2c_bus_addr = 0x32 >> 1,
342 .i2c_reg_len = REGLEN_8bit,
343 }, {
344 .id = 0x08,
345 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
346 .name = "CX24228/S5H1411-1 (QAM)",
347 .i2c_bus_nr = SAA7164_I2C_BUS_1,
348 .i2c_bus_addr = 0x34 >> 1,
349 .i2c_reg_len = REGLEN_8bit,
350 }, {
351 .id = 0x24,
352 .type = SAA7164_UNIT_TUNER,
353 .name = "TDA18271-2",
354 .i2c_bus_nr = SAA7164_I2C_BUS_2,
355 .i2c_bus_addr = 0xc0 >> 1,
356 .i2c_reg_len = REGLEN_8bit,
357 }, {
358 .id = 0x26,
359 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
360 .name = "CX24228/S5H1411-2 (TOP)",
361 .i2c_bus_nr = SAA7164_I2C_BUS_2,
362 .i2c_bus_addr = 0x32 >> 1,
363 .i2c_reg_len = REGLEN_8bit,
364 }, {
365 .id = 0x29,
366 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
367 .name = "CX24228/S5H1411-2 (QAM)",
368 .i2c_bus_nr = SAA7164_I2C_BUS_2,
369 .i2c_bus_addr = 0x34 >> 1,
370 .i2c_reg_len = REGLEN_8bit,
371 } },
372 },
373 [SAA7164_BOARD_HAUPPAUGE_HVR2250_3] = {
374 .name = "Hauppauge WinTV-HVR2250",
375 .porta = SAA7164_MPEG_DVB,
376 .portb = SAA7164_MPEG_DVB,
377 .portc = SAA7164_MPEG_ENCODER,
378 .portd = SAA7164_MPEG_ENCODER,
379 .porte = SAA7164_MPEG_VBI,
380 .portf = SAA7164_MPEG_VBI,
381 .chiprev = SAA7164_CHIP_REV3,
382 .unit = {{
383 .id = 0x26,
384 .type = SAA7164_UNIT_EEPROM,
385 .name = "4K EEPROM",
386 .i2c_bus_nr = SAA7164_I2C_BUS_0,
387 .i2c_bus_addr = 0xa0 >> 1,
388 .i2c_reg_len = REGLEN_8bit,
389 }, {
390 .id = 0x04,
391 .type = SAA7164_UNIT_TUNER,
392 .name = "TDA18271-1",
393 .i2c_bus_nr = SAA7164_I2C_BUS_1,
394 .i2c_bus_addr = 0xc0 >> 1,
395 .i2c_reg_len = REGLEN_8bit,
396 }, {
397 .id = 0x07,
398 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
399 .name = "CX24228/S5H1411-1 (TOP)",
400 .i2c_bus_nr = SAA7164_I2C_BUS_1,
401 .i2c_bus_addr = 0x32 >> 1,
402 .i2c_reg_len = REGLEN_8bit,
403 }, {
404 .id = 0x08,
405 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
406 .name = "CX24228/S5H1411-1 (QAM)",
407 .i2c_bus_nr = SAA7164_I2C_BUS_1,
408 .i2c_bus_addr = 0x34 >> 1,
409 .i2c_reg_len = REGLEN_8bit,
410 }, {
411 .id = 0x22,
412 .type = SAA7164_UNIT_TUNER,
413 .name = "TDA18271-2",
414 .i2c_bus_nr = SAA7164_I2C_BUS_2,
415 .i2c_bus_addr = 0xc0 >> 1,
416 .i2c_reg_len = REGLEN_8bit,
417 }, {
418 .id = 0x24,
419 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
420 .name = "CX24228/S5H1411-2 (TOP)",
421 .i2c_bus_nr = SAA7164_I2C_BUS_2,
422 .i2c_bus_addr = 0x32 >> 1,
423 .i2c_reg_len = REGLEN_8bit,
424 }, {
425 .id = 0x27,
426 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
427 .name = "CX24228/S5H1411-2 (QAM)",
428 .i2c_bus_nr = SAA7164_I2C_BUS_2,
429 .i2c_bus_addr = 0x34 >> 1,
430 .i2c_reg_len = REGLEN_8bit,
431 } },
432 },
433 [SAA7164_BOARD_HAUPPAUGE_HVR2200_5] = {
434 .name = "Hauppauge WinTV-HVR2200",
435 .porta = SAA7164_MPEG_DVB,
436 .portb = SAA7164_MPEG_DVB,
437 .chiprev = SAA7164_CHIP_REV3,
438 .unit = {{
439 .id = 0x23,
440 .type = SAA7164_UNIT_EEPROM,
441 .name = "4K EEPROM",
442 .i2c_bus_nr = SAA7164_I2C_BUS_0,
443 .i2c_bus_addr = 0xa0 >> 1,
444 .i2c_reg_len = REGLEN_8bit,
445 }, {
446 .id = 0x04,
447 .type = SAA7164_UNIT_TUNER,
448 .name = "TDA18271-1",
449 .i2c_bus_nr = SAA7164_I2C_BUS_1,
450 .i2c_bus_addr = 0xc0 >> 1,
451 .i2c_reg_len = REGLEN_8bit,
452 }, {
453 .id = 0x05,
454 .type = SAA7164_UNIT_ANALOG_DEMODULATOR,
455 .name = "TDA8290-1",
456 .i2c_bus_nr = SAA7164_I2C_BUS_1,
457 .i2c_bus_addr = 0x84 >> 1,
458 .i2c_reg_len = REGLEN_8bit,
459 }, {
460 .id = 0x21,
461 .type = SAA7164_UNIT_TUNER,
462 .name = "TDA18271-2",
463 .i2c_bus_nr = SAA7164_I2C_BUS_2,
464 .i2c_bus_addr = 0xc0 >> 1,
465 .i2c_reg_len = REGLEN_8bit,
466 }, {
467 .id = 0x22,
468 .type = SAA7164_UNIT_ANALOG_DEMODULATOR,
469 .name = "TDA8290-2",
470 .i2c_bus_nr = SAA7164_I2C_BUS_2,
471 .i2c_bus_addr = 0x84 >> 1,
472 .i2c_reg_len = REGLEN_8bit,
473 }, {
474 .id = 0x24,
475 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
476 .name = "TDA10048-1",
477 .i2c_bus_nr = SAA7164_I2C_BUS_1,
478 .i2c_bus_addr = 0x10 >> 1,
479 .i2c_reg_len = REGLEN_8bit,
480 }, {
481 .id = 0x25,
482 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
483 .name = "TDA10048-2",
484 .i2c_bus_nr = SAA7164_I2C_BUS_2,
485 .i2c_bus_addr = 0x12 >> 1,
486 .i2c_reg_len = REGLEN_8bit,
487 } },
488 },
489 [SAA7164_BOARD_HAUPPAUGE_HVR2255proto] = {
490 .name = "Hauppauge WinTV-HVR2255(proto)",
491 .porta = SAA7164_MPEG_DVB,
492 .portb = SAA7164_MPEG_DVB,
493 .portc = SAA7164_MPEG_ENCODER,
494 .portd = SAA7164_MPEG_ENCODER,
495 .porte = SAA7164_MPEG_VBI,
496 .portf = SAA7164_MPEG_VBI,
497 .chiprev = SAA7164_CHIP_REV3,
498 .unit = {{
499 .id = 0x27,
500 .type = SAA7164_UNIT_EEPROM,
501 .name = "4K EEPROM",
502 .i2c_bus_nr = SAA7164_I2C_BUS_0,
503 .i2c_bus_addr = 0xa0 >> 1,
504 .i2c_reg_len = REGLEN_8bit,
505 }, {
506 .id = 0x04,
507 .type = SAA7164_UNIT_TUNER,
508 .name = "SI2157-1",
509 .i2c_bus_nr = SAA7164_I2C_BUS_0,
510 .i2c_bus_addr = 0xc0 >> 1,
511 .i2c_reg_len = REGLEN_0bit,
512 }, {
513 .id = 0x06,
514 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
515 .name = "LGDT3306",
516 .i2c_bus_nr = SAA7164_I2C_BUS_2,
517 .i2c_bus_addr = 0xb2 >> 1,
518 .i2c_reg_len = REGLEN_8bit,
519 }, {
520 .id = 0x24,
521 .type = SAA7164_UNIT_TUNER,
522 .name = "SI2157-2",
523 .i2c_bus_nr = SAA7164_I2C_BUS_1,
524 .i2c_bus_addr = 0xc0 >> 1,
525 .i2c_reg_len = REGLEN_0bit,
526 }, {
527 .id = 0x26,
528 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
529 .name = "LGDT3306-2",
530 .i2c_bus_nr = SAA7164_I2C_BUS_2,
531 .i2c_bus_addr = 0x1c >> 1,
532 .i2c_reg_len = REGLEN_8bit,
533 } },
534 },
535 [SAA7164_BOARD_HAUPPAUGE_HVR2255] = {
536 .name = "Hauppauge WinTV-HVR2255",
537 .porta = SAA7164_MPEG_DVB,
538 .portb = SAA7164_MPEG_DVB,
539 .portc = SAA7164_MPEG_ENCODER,
540 .portd = SAA7164_MPEG_ENCODER,
541 .porte = SAA7164_MPEG_VBI,
542 .portf = SAA7164_MPEG_VBI,
543 .chiprev = SAA7164_CHIP_REV3,
544 .unit = {{
545 .id = 0x28,
546 .type = SAA7164_UNIT_EEPROM,
547 .name = "4K EEPROM",
548 .i2c_bus_nr = SAA7164_I2C_BUS_0,
549 .i2c_bus_addr = 0xa0 >> 1,
550 .i2c_reg_len = REGLEN_8bit,
551 }, {
552 .id = 0x04,
553 .type = SAA7164_UNIT_TUNER,
554 .name = "SI2157-1",
555 .i2c_bus_nr = SAA7164_I2C_BUS_0,
556 .i2c_bus_addr = 0xc0 >> 1,
557 .i2c_reg_len = REGLEN_0bit,
558 }, {
559 .id = 0x06,
560 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
561 .name = "LGDT3306-1",
562 .i2c_bus_nr = SAA7164_I2C_BUS_2,
563 .i2c_bus_addr = 0xb2 >> 1,
564 .i2c_reg_len = REGLEN_8bit,
565 }, {
566 .id = 0x25,
567 .type = SAA7164_UNIT_TUNER,
568 .name = "SI2157-2",
569 .i2c_bus_nr = SAA7164_I2C_BUS_1,
570 .i2c_bus_addr = 0xc0 >> 1,
571 .i2c_reg_len = REGLEN_0bit,
572 }, {
573 .id = 0x27,
574 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
575 .name = "LGDT3306-2",
576 .i2c_bus_nr = SAA7164_I2C_BUS_2,
577 .i2c_bus_addr = 0x1c >> 1,
578 .i2c_reg_len = REGLEN_8bit,
579 } },
580 },
581 [SAA7164_BOARD_HAUPPAUGE_HVR2205] = {
582 .name = "Hauppauge WinTV-HVR2205",
583 .porta = SAA7164_MPEG_DVB,
584 .portb = SAA7164_MPEG_DVB,
585 .portc = SAA7164_MPEG_ENCODER,
586 .portd = SAA7164_MPEG_ENCODER,
587 .porte = SAA7164_MPEG_VBI,
588 .portf = SAA7164_MPEG_VBI,
589 .chiprev = SAA7164_CHIP_REV3,
590 .unit = {{
591 .id = 0x28,
592 .type = SAA7164_UNIT_EEPROM,
593 .name = "4K EEPROM",
594 .i2c_bus_nr = SAA7164_I2C_BUS_0,
595 .i2c_bus_addr = 0xa0 >> 1,
596 .i2c_reg_len = REGLEN_8bit,
597 }, {
598 .id = 0x04,
599 .type = SAA7164_UNIT_TUNER,
600 .name = "SI2157-1",
601 .i2c_bus_nr = SAA7164_I2C_BUS_0,
602 .i2c_bus_addr = 0xc0 >> 1,
603 .i2c_reg_len = REGLEN_0bit,
604 }, {
605 .id = 0x06,
606 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
607 .name = "SI2168-1",
608 .i2c_bus_nr = SAA7164_I2C_BUS_2,
609 .i2c_bus_addr = 0xc8 >> 1,
610 .i2c_reg_len = REGLEN_0bit,
611 }, {
612 .id = 0x25,
613 .type = SAA7164_UNIT_TUNER,
614 .name = "SI2157-2",
615 .i2c_bus_nr = SAA7164_I2C_BUS_1,
616 .i2c_bus_addr = 0xc0 >> 1,
617 .i2c_reg_len = REGLEN_0bit,
618 }, {
619 .id = 0x27,
620 .type = SAA7164_UNIT_DIGITAL_DEMODULATOR,
621 .name = "SI2168-2",
622 .i2c_bus_nr = SAA7164_I2C_BUS_2,
623 .i2c_bus_addr = 0xcc >> 1,
624 .i2c_reg_len = REGLEN_0bit,
625 } },
626 },
627 };
628 const unsigned int saa7164_bcount = ARRAY_SIZE(saa7164_boards);
629
630 /* ------------------------------------------------------------------ */
631 /* PCI subsystem IDs */
632
633 struct saa7164_subid saa7164_subids[] = {
634 {
635 .subvendor = 0x0070,
636 .subdevice = 0x8880,
637 .card = SAA7164_BOARD_HAUPPAUGE_HVR2250,
638 }, {
639 .subvendor = 0x0070,
640 .subdevice = 0x8810,
641 .card = SAA7164_BOARD_HAUPPAUGE_HVR2250,
642 }, {
643 .subvendor = 0x0070,
644 .subdevice = 0x8980,
645 .card = SAA7164_BOARD_HAUPPAUGE_HVR2200,
646 }, {
647 .subvendor = 0x0070,
648 .subdevice = 0x8900,
649 .card = SAA7164_BOARD_HAUPPAUGE_HVR2200_2,
650 }, {
651 .subvendor = 0x0070,
652 .subdevice = 0x8901,
653 .card = SAA7164_BOARD_HAUPPAUGE_HVR2200_3,
654 }, {
655 .subvendor = 0x0070,
656 .subdevice = 0x88A1,
657 .card = SAA7164_BOARD_HAUPPAUGE_HVR2250_3,
658 }, {
659 .subvendor = 0x0070,
660 .subdevice = 0x8891,
661 .card = SAA7164_BOARD_HAUPPAUGE_HVR2250_2,
662 }, {
663 .subvendor = 0x0070,
664 .subdevice = 0x8851,
665 .card = SAA7164_BOARD_HAUPPAUGE_HVR2250_2,
666 }, {
667 .subvendor = 0x0070,
668 .subdevice = 0x8940,
669 .card = SAA7164_BOARD_HAUPPAUGE_HVR2200_4,
670 }, {
671 .subvendor = 0x0070,
672 .subdevice = 0x8953,
673 .card = SAA7164_BOARD_HAUPPAUGE_HVR2200_5,
674 }, {
675 .subvendor = 0x0070,
676 .subdevice = 0xf111,
677 .card = SAA7164_BOARD_HAUPPAUGE_HVR2255,
678 /* Prototype card left here for documentation purposes.
679 .card = SAA7164_BOARD_HAUPPAUGE_HVR2255proto,
680 */
681 }, {
682 .subvendor = 0x0070,
683 .subdevice = 0xf123,
684 .card = SAA7164_BOARD_HAUPPAUGE_HVR2205,
685 }, {
686 .subvendor = 0x0070,
687 .subdevice = 0xf120,
688 .card = SAA7164_BOARD_HAUPPAUGE_HVR2205,
689 },
690 };
691 const unsigned int saa7164_idcount = ARRAY_SIZE(saa7164_subids);
692
saa7164_card_list(struct saa7164_dev * dev)693 void saa7164_card_list(struct saa7164_dev *dev)
694 {
695 int i;
696
697 if (0 == dev->pci->subsystem_vendor &&
698 0 == dev->pci->subsystem_device) {
699 printk(KERN_ERR
700 "%s: Board has no valid PCIe Subsystem ID and can't\n"
701 "%s: be autodetected. Pass card=<n> insmod option to\n"
702 "%s: workaround that. Send complaints to the vendor\n"
703 "%s: of the TV card. Best regards,\n"
704 "%s: -- tux\n",
705 dev->name, dev->name, dev->name, dev->name, dev->name);
706 } else {
707 printk(KERN_ERR
708 "%s: Your board isn't known (yet) to the driver.\n"
709 "%s: Try to pick one of the existing card configs via\n"
710 "%s: card=<n> insmod option. Updating to the latest\n"
711 "%s: version might help as well.\n",
712 dev->name, dev->name, dev->name, dev->name);
713 }
714
715 printk(KERN_ERR "%s: Here are valid choices for the card=<n> insmod option:\n",
716 dev->name);
717
718 for (i = 0; i < saa7164_bcount; i++)
719 printk(KERN_ERR "%s: card=%d -> %s\n",
720 dev->name, i, saa7164_boards[i].name);
721 }
722
723 /* TODO: clean this define up into the -cards.c structs */
724 #define PCIEBRIDGE_UNITID 2
725
saa7164_gpio_setup(struct saa7164_dev * dev)726 void saa7164_gpio_setup(struct saa7164_dev *dev)
727 {
728 switch (dev->board) {
729 case SAA7164_BOARD_HAUPPAUGE_HVR2200:
730 case SAA7164_BOARD_HAUPPAUGE_HVR2200_2:
731 case SAA7164_BOARD_HAUPPAUGE_HVR2200_3:
732 case SAA7164_BOARD_HAUPPAUGE_HVR2200_4:
733 case SAA7164_BOARD_HAUPPAUGE_HVR2200_5:
734 case SAA7164_BOARD_HAUPPAUGE_HVR2250:
735 case SAA7164_BOARD_HAUPPAUGE_HVR2250_2:
736 case SAA7164_BOARD_HAUPPAUGE_HVR2250_3:
737 case SAA7164_BOARD_HAUPPAUGE_HVR2255proto:
738 case SAA7164_BOARD_HAUPPAUGE_HVR2255:
739 case SAA7164_BOARD_HAUPPAUGE_HVR2205:
740 /*
741 HVR2200 / HVR2250
742 GPIO 2: s5h1411 / tda10048-1 demod reset
743 GPIO 3: s5h1411 / tda10048-2 demod reset
744 GPIO 7: IRBlaster Zilog reset
745 */
746
747 /* HVR2255
748 * GPIO 2: lgdg3306-1 demod reset
749 * GPIO 3: lgdt3306-2 demod reset
750 */
751
752 /* HVR2205
753 * GPIO 2: si2168-1 demod reset
754 * GPIO 3: si2168-2 demod reset
755 */
756
757 /* Reset parts by going in and out of reset */
758 saa7164_api_clear_gpiobit(dev, PCIEBRIDGE_UNITID, 2);
759 saa7164_api_clear_gpiobit(dev, PCIEBRIDGE_UNITID, 3);
760
761 msleep(20);
762
763 saa7164_api_set_gpiobit(dev, PCIEBRIDGE_UNITID, 2);
764 saa7164_api_set_gpiobit(dev, PCIEBRIDGE_UNITID, 3);
765 break;
766 }
767 }
768
hauppauge_eeprom(struct saa7164_dev * dev,u8 * eeprom_data)769 static void hauppauge_eeprom(struct saa7164_dev *dev, u8 *eeprom_data)
770 {
771 struct tveeprom tv;
772
773 tveeprom_hauppauge_analog(&tv, eeprom_data);
774
775 /* Make sure we support the board model */
776 switch (tv.model) {
777 case 88001:
778 /* Development board - Limit circulation */
779 /* WinTV-HVR2250 (PCIe, Retail, full-height bracket)
780 * ATSC/QAM (TDA18271/S5H1411) and basic analog, no IR, FM */
781 case 88021:
782 /* WinTV-HVR2250 (PCIe, Retail, full-height bracket)
783 * ATSC/QAM (TDA18271/S5H1411) and basic analog, MCE CIR, FM */
784 break;
785 case 88041:
786 /* WinTV-HVR2250 (PCIe, Retail, full-height bracket)
787 * ATSC/QAM (TDA18271/S5H1411) and basic analog, no IR, FM */
788 break;
789 case 88061:
790 /* WinTV-HVR2250 (PCIe, Retail, full-height bracket)
791 * ATSC/QAM (TDA18271/S5H1411) and basic analog, FM */
792 break;
793 case 89519:
794 case 89609:
795 /* WinTV-HVR2200 (PCIe, Retail, full-height)
796 * DVB-T (TDA18271/TDA10048) and basic analog, no IR */
797 break;
798 case 89619:
799 /* WinTV-HVR2200 (PCIe, Retail, half-height)
800 * DVB-T (TDA18271/TDA10048) and basic analog, no IR */
801 break;
802 case 151009:
803 /* First production board rev B2I6 */
804 /* WinTV-HVR2205 (PCIe, Retail, full-height bracket)
805 * DVB-T/T2/C (SI2157/SI2168) and basic analog, FM */
806 break;
807 case 151609:
808 /* First production board rev B2I6 */
809 /* WinTV-HVR2205 (PCIe, Retail, half-height bracket)
810 * DVB-T/T2/C (SI2157/SI2168) and basic analog, FM */
811 break;
812 case 151061:
813 /* First production board rev B1I6 */
814 /* WinTV-HVR2255 (PCIe, Retail, full-height bracket)
815 * ATSC/QAM (SI2157/LGDT3306) and basic analog, FM */
816 break;
817 default:
818 printk(KERN_ERR "%s: Warning: Unknown Hauppauge model #%d\n",
819 dev->name, tv.model);
820 break;
821 }
822
823 printk(KERN_INFO "%s: Hauppauge eeprom: model=%d\n", dev->name,
824 tv.model);
825 }
826
saa7164_card_setup(struct saa7164_dev * dev)827 void saa7164_card_setup(struct saa7164_dev *dev)
828 {
829 static u8 eeprom[256];
830
831 if (dev->i2c_bus[0].i2c_rc == 0) {
832 if (saa7164_api_read_eeprom(dev, &eeprom[0],
833 sizeof(eeprom)) < 0)
834 return;
835 }
836
837 switch (dev->board) {
838 case SAA7164_BOARD_HAUPPAUGE_HVR2200:
839 case SAA7164_BOARD_HAUPPAUGE_HVR2200_2:
840 case SAA7164_BOARD_HAUPPAUGE_HVR2200_3:
841 case SAA7164_BOARD_HAUPPAUGE_HVR2200_4:
842 case SAA7164_BOARD_HAUPPAUGE_HVR2200_5:
843 case SAA7164_BOARD_HAUPPAUGE_HVR2250:
844 case SAA7164_BOARD_HAUPPAUGE_HVR2250_2:
845 case SAA7164_BOARD_HAUPPAUGE_HVR2250_3:
846 case SAA7164_BOARD_HAUPPAUGE_HVR2255proto:
847 case SAA7164_BOARD_HAUPPAUGE_HVR2255:
848 case SAA7164_BOARD_HAUPPAUGE_HVR2205:
849 hauppauge_eeprom(dev, &eeprom[0]);
850 break;
851 }
852 }
853
854 /* With most other drivers, the kernel expects to communicate with subdrivers
855 * through i2c. This bridge does not allow that, it does not expose any direct
856 * access to I2C. Instead we have to communicate through the device f/w for
857 * register access to 'processing units'. Each unit has a unique
858 * id, regardless of how the physical implementation occurs across
859 * the three physical i2c buses. The being said if we want leverge of
860 * the existing kernel drivers for tuners and demods we have to 'speak i2c',
861 * to this bridge implements 3 virtual i2c buses. This is a helper function
862 * for those.
863 *
864 * Description: Translate the kernels notion of an i2c address and bus into
865 * the appropriate unitid.
866 */
saa7164_i2caddr_to_unitid(struct saa7164_i2c * bus,int addr)867 int saa7164_i2caddr_to_unitid(struct saa7164_i2c *bus, int addr)
868 {
869 /* For a given bus and i2c device address, return the saa7164 unique
870 * unitid. < 0 on error */
871
872 struct saa7164_dev *dev = bus->dev;
873 struct saa7164_unit *unit;
874 int i;
875
876 for (i = 0; i < SAA7164_MAX_UNITS; i++) {
877 unit = &saa7164_boards[dev->board].unit[i];
878
879 if (unit->type == SAA7164_UNIT_UNDEFINED)
880 continue;
881 if ((bus->nr == unit->i2c_bus_nr) &&
882 (addr == unit->i2c_bus_addr))
883 return unit->id;
884 }
885
886 return -1;
887 }
888
889 /* The 7164 API needs to know the i2c register length in advance.
890 * this is a helper function. Based on a specific chip addr and bus return the
891 * reg length.
892 */
saa7164_i2caddr_to_reglen(struct saa7164_i2c * bus,int addr)893 int saa7164_i2caddr_to_reglen(struct saa7164_i2c *bus, int addr)
894 {
895 /* For a given bus and i2c device address, return the
896 * saa7164 registry address width. < 0 on error
897 */
898
899 struct saa7164_dev *dev = bus->dev;
900 struct saa7164_unit *unit;
901 int i;
902
903 for (i = 0; i < SAA7164_MAX_UNITS; i++) {
904 unit = &saa7164_boards[dev->board].unit[i];
905
906 if (unit->type == SAA7164_UNIT_UNDEFINED)
907 continue;
908
909 if ((bus->nr == unit->i2c_bus_nr) &&
910 (addr == unit->i2c_bus_addr))
911 return unit->i2c_reg_len;
912 }
913
914 return -1;
915 }
916 /* TODO: implement a 'findeeprom' functio like the above and fix any other
917 * eeprom related todo's in -api.c.
918 */
919
920 /* Translate a unitid into a x readable device name, for display purposes. */
saa7164_unitid_name(struct saa7164_dev * dev,u8 unitid)921 char *saa7164_unitid_name(struct saa7164_dev *dev, u8 unitid)
922 {
923 char *undefed = "UNDEFINED";
924 char *bridge = "BRIDGE";
925 struct saa7164_unit *unit;
926 int i;
927
928 if (unitid == 0)
929 return bridge;
930
931 for (i = 0; i < SAA7164_MAX_UNITS; i++) {
932 unit = &saa7164_boards[dev->board].unit[i];
933
934 if (unit->type == SAA7164_UNIT_UNDEFINED)
935 continue;
936
937 if (unitid == unit->id)
938 return unit->name;
939 }
940
941 return undefed;
942 }
943
944