1# SPDX-License-Identifier: GPL-2.0-only 2config OMAP2_DSS_INIT 3 bool 4 5config OMAP_DSS_BASE 6 tristate 7 8menuconfig OMAP2_DSS 9 tristate "OMAP2+ Display Subsystem support" 10 select OMAP_DSS_BASE 11 select VIDEOMODE_HELPERS 12 select OMAP2_DSS_INIT 13 select HDMI 14 help 15 OMAP2+ Display Subsystem support. 16 17if OMAP2_DSS 18 19config OMAP2_DSS_DEBUG 20 bool "Debug support" 21 default n 22 help 23 This enables printing of debug messages. Alternatively, debug messages 24 can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting 25 appropriate flags in <debugfs>/dynamic_debug/control. 26 27config OMAP2_DSS_DEBUGFS 28 bool "Debugfs filesystem support" 29 depends on DEBUG_FS 30 default n 31 help 32 This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables 33 querying about clock configuration and register configuration of dss, 34 dispc, dsi, hdmi and rfbi. 35 36config OMAP2_DSS_COLLECT_IRQ_STATS 37 bool "Collect DSS IRQ statistics" 38 depends on OMAP2_DSS_DEBUGFS 39 default n 40 help 41 Collect DSS IRQ statistics, printable via debugfs. 42 43 The statistics can be found from 44 <debugfs>/omapdss/dispc_irq for DISPC interrupts, and 45 <debugfs>/omapdss/dsi_irq for DSI interrupts. 46 47config OMAP2_DSS_DPI 48 bool "DPI support" 49 default y 50 help 51 DPI Interface. This is the Parallel Display Interface. 52 53config OMAP2_DSS_VENC 54 bool "VENC support" 55 default y 56 help 57 OMAP Video Encoder support for S-Video and composite TV-out. 58 59config OMAP2_DSS_HDMI_COMMON 60 bool 61 62config OMAP4_DSS_HDMI 63 bool "HDMI support for OMAP4" 64 default y 65 select OMAP2_DSS_HDMI_COMMON 66 help 67 HDMI support for OMAP4 based SoCs. 68 69config OMAP4_DSS_HDMI_CEC 70 bool "Enable HDMI CEC support for OMAP4" 71 depends on OMAP4_DSS_HDMI 72 select CEC_CORE 73 default y 74 help 75 When selected the HDMI transmitter will support the CEC feature. 76 77config OMAP5_DSS_HDMI 78 bool "HDMI support for OMAP5" 79 default n 80 select OMAP2_DSS_HDMI_COMMON 81 help 82 HDMI Interface for OMAP5 and similar cores. This adds the High 83 Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI 84 specification. 85 86config OMAP2_DSS_SDI 87 bool "SDI support" 88 default n 89 help 90 SDI (Serial Display Interface) support. 91 92 SDI is a high speed one-way display serial bus between the host 93 processor and a display. 94 95config OMAP2_DSS_DSI 96 bool "DSI support" 97 default n 98 help 99 MIPI DSI (Display Serial Interface) support. 100 101 DSI is a high speed half-duplex serial interface between the host 102 processor and a peripheral, such as a display or a framebuffer chip. 103 104 See http://www.mipi.org/ for DSI specifications. 105 106config OMAP2_DSS_MIN_FCK_PER_PCK 107 int "Minimum FCK/PCK ratio (for scaling)" 108 range 0 32 109 default 0 110 help 111 This can be used to adjust the minimum FCK/PCK ratio. 112 113 With this you can make sure that DISPC FCK is at least 114 n x PCK. Video plane scaling requires higher FCK than 115 normally. 116 117 If this is set to 0, there's no extra constraint on the 118 DISPC FCK. However, the FCK will at minimum be 119 2xPCK (if active matrix) or 3xPCK (if passive matrix). 120 121 Max FCK is 173MHz, so this doesn't work if your PCK 122 is very high. 123 124config OMAP2_DSS_SLEEP_AFTER_VENC_RESET 125 bool "Sleep 20ms after VENC reset" 126 default y 127 help 128 There is a 20ms sleep after VENC reset which seemed to fix the 129 reset. The reason for the bug is unclear, and it's also unclear 130 on what platforms this happens. 131 132 This option enables the sleep, and is enabled by default. You can 133 disable the sleep if it doesn't cause problems on your platform. 134 135endif 136