1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * cx18 gpio functions
4 *
5 * Derived from ivtv-gpio.c
6 *
7 * Copyright (C) 2007 Hans Verkuil <hverkuil@xs4all.nl>
8 * Copyright (C) 2008 Andy Walls <awalls@md.metrocast.net>
9 */
10
11 #include "cx18-driver.h"
12 #include "cx18-io.h"
13 #include "cx18-cards.h"
14 #include "cx18-gpio.h"
15 #include "tuner-xc2028.h"
16
17 /********************* GPIO stuffs *********************/
18
19 /* GPIO registers */
20 #define CX18_REG_GPIO_IN 0xc72010
21 #define CX18_REG_GPIO_OUT1 0xc78100
22 #define CX18_REG_GPIO_DIR1 0xc78108
23 #define CX18_REG_GPIO_OUT2 0xc78104
24 #define CX18_REG_GPIO_DIR2 0xc7810c
25
26 /*
27 * HVR-1600 GPIO pins, courtesy of Hauppauge:
28 *
29 * gpio0: zilog ir process reset pin
30 * gpio1: zilog programming pin (you should never use this)
31 * gpio12: cx24227 reset pin
32 * gpio13: cs5345 reset pin
33 */
34
35 /*
36 * File scope utility functions
37 */
gpio_write(struct cx18 * cx)38 static void gpio_write(struct cx18 *cx)
39 {
40 u32 dir_lo = cx->gpio_dir & 0xffff;
41 u32 val_lo = cx->gpio_val & 0xffff;
42 u32 dir_hi = cx->gpio_dir >> 16;
43 u32 val_hi = cx->gpio_val >> 16;
44
45 cx18_write_reg_expect(cx, dir_lo << 16,
46 CX18_REG_GPIO_DIR1, ~dir_lo, dir_lo);
47 cx18_write_reg_expect(cx, (dir_lo << 16) | val_lo,
48 CX18_REG_GPIO_OUT1, val_lo, dir_lo);
49 cx18_write_reg_expect(cx, dir_hi << 16,
50 CX18_REG_GPIO_DIR2, ~dir_hi, dir_hi);
51 cx18_write_reg_expect(cx, (dir_hi << 16) | val_hi,
52 CX18_REG_GPIO_OUT2, val_hi, dir_hi);
53 }
54
gpio_update(struct cx18 * cx,u32 mask,u32 data)55 static void gpio_update(struct cx18 *cx, u32 mask, u32 data)
56 {
57 if (mask == 0)
58 return;
59
60 mutex_lock(&cx->gpio_lock);
61 cx->gpio_val = (cx->gpio_val & ~mask) | (data & mask);
62 gpio_write(cx);
63 mutex_unlock(&cx->gpio_lock);
64 }
65
gpio_reset_seq(struct cx18 * cx,u32 active_lo,u32 active_hi,unsigned int assert_msecs,unsigned int recovery_msecs)66 static void gpio_reset_seq(struct cx18 *cx, u32 active_lo, u32 active_hi,
67 unsigned int assert_msecs,
68 unsigned int recovery_msecs)
69 {
70 u32 mask;
71
72 mask = active_lo | active_hi;
73 if (mask == 0)
74 return;
75
76 /*
77 * Assuming that active_hi and active_lo are a subsets of the bits in
78 * gpio_dir. Also assumes that active_lo and active_hi don't overlap
79 * in any bit position
80 */
81
82 /* Assert */
83 gpio_update(cx, mask, ~active_lo);
84 schedule_timeout_uninterruptible(msecs_to_jiffies(assert_msecs));
85
86 /* Deassert */
87 gpio_update(cx, mask, ~active_hi);
88 schedule_timeout_uninterruptible(msecs_to_jiffies(recovery_msecs));
89 }
90
91 /*
92 * GPIO Multiplexer - logical device
93 */
gpiomux_log_status(struct v4l2_subdev * sd)94 static int gpiomux_log_status(struct v4l2_subdev *sd)
95 {
96 struct cx18 *cx = v4l2_get_subdevdata(sd);
97
98 mutex_lock(&cx->gpio_lock);
99 CX18_INFO_DEV(sd, "GPIO: direction 0x%08x, value 0x%08x\n",
100 cx->gpio_dir, cx->gpio_val);
101 mutex_unlock(&cx->gpio_lock);
102 return 0;
103 }
104
gpiomux_s_radio(struct v4l2_subdev * sd)105 static int gpiomux_s_radio(struct v4l2_subdev *sd)
106 {
107 struct cx18 *cx = v4l2_get_subdevdata(sd);
108
109 /*
110 * FIXME - work out the cx->active/audio_input mess - this is
111 * intended to handle the switch to radio mode and set the
112 * audio routing, but we need to update the state in cx
113 */
114 gpio_update(cx, cx->card->gpio_audio_input.mask,
115 cx->card->gpio_audio_input.radio);
116 return 0;
117 }
118
gpiomux_s_std(struct v4l2_subdev * sd,v4l2_std_id norm)119 static int gpiomux_s_std(struct v4l2_subdev *sd, v4l2_std_id norm)
120 {
121 struct cx18 *cx = v4l2_get_subdevdata(sd);
122 u32 data;
123
124 switch (cx->card->audio_inputs[cx->audio_input].muxer_input) {
125 case 1:
126 data = cx->card->gpio_audio_input.linein;
127 break;
128 case 0:
129 data = cx->card->gpio_audio_input.tuner;
130 break;
131 default:
132 /*
133 * FIXME - work out the cx->active/audio_input mess - this is
134 * intended to handle the switch from radio mode and set the
135 * audio routing, but we need to update the state in cx
136 */
137 data = cx->card->gpio_audio_input.tuner;
138 break;
139 }
140 gpio_update(cx, cx->card->gpio_audio_input.mask, data);
141 return 0;
142 }
143
gpiomux_s_audio_routing(struct v4l2_subdev * sd,u32 input,u32 output,u32 config)144 static int gpiomux_s_audio_routing(struct v4l2_subdev *sd,
145 u32 input, u32 output, u32 config)
146 {
147 struct cx18 *cx = v4l2_get_subdevdata(sd);
148 u32 data;
149
150 switch (input) {
151 case 0:
152 data = cx->card->gpio_audio_input.tuner;
153 break;
154 case 1:
155 data = cx->card->gpio_audio_input.linein;
156 break;
157 case 2:
158 data = cx->card->gpio_audio_input.radio;
159 break;
160 default:
161 return -EINVAL;
162 }
163 gpio_update(cx, cx->card->gpio_audio_input.mask, data);
164 return 0;
165 }
166
167 static const struct v4l2_subdev_core_ops gpiomux_core_ops = {
168 .log_status = gpiomux_log_status,
169 };
170
171 static const struct v4l2_subdev_tuner_ops gpiomux_tuner_ops = {
172 .s_radio = gpiomux_s_radio,
173 };
174
175 static const struct v4l2_subdev_audio_ops gpiomux_audio_ops = {
176 .s_routing = gpiomux_s_audio_routing,
177 };
178
179 static const struct v4l2_subdev_video_ops gpiomux_video_ops = {
180 .s_std = gpiomux_s_std,
181 };
182
183 static const struct v4l2_subdev_ops gpiomux_ops = {
184 .core = &gpiomux_core_ops,
185 .tuner = &gpiomux_tuner_ops,
186 .audio = &gpiomux_audio_ops,
187 .video = &gpiomux_video_ops,
188 };
189
190 /*
191 * GPIO Reset Controller - logical device
192 */
resetctrl_log_status(struct v4l2_subdev * sd)193 static int resetctrl_log_status(struct v4l2_subdev *sd)
194 {
195 struct cx18 *cx = v4l2_get_subdevdata(sd);
196
197 mutex_lock(&cx->gpio_lock);
198 CX18_INFO_DEV(sd, "GPIO: direction 0x%08x, value 0x%08x\n",
199 cx->gpio_dir, cx->gpio_val);
200 mutex_unlock(&cx->gpio_lock);
201 return 0;
202 }
203
resetctrl_reset(struct v4l2_subdev * sd,u32 val)204 static int resetctrl_reset(struct v4l2_subdev *sd, u32 val)
205 {
206 struct cx18 *cx = v4l2_get_subdevdata(sd);
207 const struct cx18_gpio_i2c_slave_reset *p;
208
209 p = &cx->card->gpio_i2c_slave_reset;
210 switch (val) {
211 case CX18_GPIO_RESET_I2C:
212 gpio_reset_seq(cx, p->active_lo_mask, p->active_hi_mask,
213 p->msecs_asserted, p->msecs_recovery);
214 break;
215 case CX18_GPIO_RESET_Z8F0811:
216 /*
217 * Assert timing for the Z8F0811 on HVR-1600 boards:
218 * 1. Assert RESET for min of 4 clock cycles at 18.432 MHz to
219 * initiate
220 * 2. Reset then takes 66 WDT cycles at 10 kHz + 16 xtal clock
221 * cycles (6,601,085 nanoseconds ~= 7 milliseconds)
222 * 3. DBG pin must be high before chip exits reset for normal
223 * operation. DBG is open drain and hopefully pulled high
224 * since we don't normally drive it (GPIO 1?) for the
225 * HVR-1600
226 * 4. Z8F0811 won't exit reset until RESET is deasserted
227 * 5. Zilog comes out of reset, loads reset vector address and
228 * executes from there. Required recovery delay unknown.
229 */
230 gpio_reset_seq(cx, p->ir_reset_mask, 0,
231 p->msecs_asserted, p->msecs_recovery);
232 break;
233 case CX18_GPIO_RESET_XC2028:
234 if (cx->card->tuners[0].tuner == TUNER_XC2028)
235 gpio_reset_seq(cx, (1 << cx->card->xceive_pin), 0,
236 1, 1);
237 break;
238 }
239 return 0;
240 }
241
242 static const struct v4l2_subdev_core_ops resetctrl_core_ops = {
243 .log_status = resetctrl_log_status,
244 .reset = resetctrl_reset,
245 };
246
247 static const struct v4l2_subdev_ops resetctrl_ops = {
248 .core = &resetctrl_core_ops,
249 };
250
251 /*
252 * External entry points
253 */
cx18_gpio_init(struct cx18 * cx)254 void cx18_gpio_init(struct cx18 *cx)
255 {
256 mutex_lock(&cx->gpio_lock);
257 cx->gpio_dir = cx->card->gpio_init.direction;
258 cx->gpio_val = cx->card->gpio_init.initial_value;
259
260 if (cx->card->tuners[0].tuner == TUNER_XC2028) {
261 cx->gpio_dir |= 1 << cx->card->xceive_pin;
262 cx->gpio_val |= 1 << cx->card->xceive_pin;
263 }
264
265 if (cx->gpio_dir == 0) {
266 mutex_unlock(&cx->gpio_lock);
267 return;
268 }
269
270 CX18_DEBUG_INFO("GPIO initial dir: %08x/%08x out: %08x/%08x\n",
271 cx18_read_reg(cx, CX18_REG_GPIO_DIR1),
272 cx18_read_reg(cx, CX18_REG_GPIO_DIR2),
273 cx18_read_reg(cx, CX18_REG_GPIO_OUT1),
274 cx18_read_reg(cx, CX18_REG_GPIO_OUT2));
275
276 gpio_write(cx);
277 mutex_unlock(&cx->gpio_lock);
278 }
279
cx18_gpio_register(struct cx18 * cx,u32 hw)280 int cx18_gpio_register(struct cx18 *cx, u32 hw)
281 {
282 struct v4l2_subdev *sd;
283 const struct v4l2_subdev_ops *ops;
284 char *str;
285
286 switch (hw) {
287 case CX18_HW_GPIO_MUX:
288 sd = &cx->sd_gpiomux;
289 ops = &gpiomux_ops;
290 str = "gpio-mux";
291 break;
292 case CX18_HW_GPIO_RESET_CTRL:
293 sd = &cx->sd_resetctrl;
294 ops = &resetctrl_ops;
295 str = "gpio-reset-ctrl";
296 break;
297 default:
298 return -EINVAL;
299 }
300
301 v4l2_subdev_init(sd, ops);
302 v4l2_set_subdevdata(sd, cx);
303 snprintf(sd->name, sizeof(sd->name), "%s %s", cx->v4l2_dev.name, str);
304 sd->grp_id = hw;
305 return v4l2_device_register_subdev(&cx->v4l2_dev, sd);
306 }
307
cx18_reset_ir_gpio(void * data)308 void cx18_reset_ir_gpio(void *data)
309 {
310 struct cx18 *cx = to_cx18((struct v4l2_device *)data);
311
312 if (cx->card->gpio_i2c_slave_reset.ir_reset_mask == 0)
313 return;
314
315 CX18_DEBUG_INFO("Resetting IR microcontroller\n");
316
317 v4l2_subdev_call(&cx->sd_resetctrl,
318 core, reset, CX18_GPIO_RESET_Z8F0811);
319 }
320 EXPORT_SYMBOL(cx18_reset_ir_gpio);
321 /* This symbol is exported for use by lirc_pvr150 for the IR-blaster */
322
323 /* Xceive tuner reset function */
cx18_reset_tuner_gpio(void * dev,int component,int cmd,int value)324 int cx18_reset_tuner_gpio(void *dev, int component, int cmd, int value)
325 {
326 struct i2c_algo_bit_data *algo = dev;
327 struct cx18_i2c_algo_callback_data *cb_data = algo->data;
328 struct cx18 *cx = cb_data->cx;
329
330 if (cmd != XC2028_TUNER_RESET ||
331 cx->card->tuners[0].tuner != TUNER_XC2028)
332 return 0;
333
334 CX18_DEBUG_INFO("Resetting XCeive tuner\n");
335 return v4l2_subdev_call(&cx->sd_resetctrl,
336 core, reset, CX18_GPIO_RESET_XC2028);
337 }
338