1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Murata ZPA2326 pressure and temperature sensor IIO driver
4 *
5 * Copyright (c) 2016 Parrot S.A.
6 *
7 * Author: Gregor Boirie <gregor.boirie@parrot.com>
8 */
9
10 /**
11 * DOC: ZPA2326 theory of operations
12 *
13 * This driver supports %INDIO_DIRECT_MODE and %INDIO_BUFFER_TRIGGERED IIO
14 * modes.
15 * A internal hardware trigger is also implemented to dispatch registered IIO
16 * trigger consumers upon "sample ready" interrupts.
17 *
18 * ZPA2326 hardware supports 2 sampling mode: one shot and continuous.
19 *
20 * A complete one shot sampling cycle gets device out of low power mode,
21 * performs pressure and temperature measurements, then automatically switches
22 * back to low power mode. It is meant for on demand sampling with optimal power
23 * saving at the cost of lower sampling rate and higher software overhead.
24 * This is a natural candidate for IIO read_raw hook implementation
25 * (%INDIO_DIRECT_MODE). It is also used for triggered buffering support to
26 * ensure explicit synchronization with external trigger events
27 * (%INDIO_BUFFER_TRIGGERED).
28 *
29 * The continuous mode works according to a periodic hardware measurement
30 * process continuously pushing samples into an internal hardware FIFO (for
31 * pressure samples only). Measurement cycle completion may be signaled by a
32 * "sample ready" interrupt.
33 * Typical software sequence of operations :
34 * - get device out of low power mode,
35 * - setup hardware sampling period,
36 * - at end of period, upon data ready interrupt: pop pressure samples out of
37 * hardware FIFO and fetch temperature sample
38 * - when no longer needed, stop sampling process by putting device into
39 * low power mode.
40 * This mode is used to implement %INDIO_BUFFER_TRIGGERED mode if device tree
41 * declares a valid interrupt line. In this case, the internal hardware trigger
42 * drives acquisition.
43 *
44 * Note that hardware sampling frequency is taken into account only when
45 * internal hardware trigger is attached as the highest sampling rate seems to
46 * be the most energy efficient.
47 *
48 * TODO:
49 * preset pressure threshold crossing / IIO events ;
50 * differential pressure sampling ;
51 * hardware samples averaging.
52 */
53
54 #include <linux/module.h>
55 #include <linux/kernel.h>
56 #include <linux/delay.h>
57 #include <linux/interrupt.h>
58 #include <linux/regulator/consumer.h>
59 #include <linux/pm_runtime.h>
60 #include <linux/regmap.h>
61 #include <linux/iio/iio.h>
62 #include <linux/iio/sysfs.h>
63 #include <linux/iio/buffer.h>
64 #include <linux/iio/trigger.h>
65 #include <linux/iio/trigger_consumer.h>
66 #include <linux/iio/triggered_buffer.h>
67 #include <asm/unaligned.h>
68 #include "zpa2326.h"
69
70 /* 200 ms should be enough for the longest conversion time in one-shot mode. */
71 #define ZPA2326_CONVERSION_JIFFIES (HZ / 5)
72
73 /* There should be a 1 ms delay (Tpup) after getting out of reset. */
74 #define ZPA2326_TPUP_USEC_MIN (1000)
75 #define ZPA2326_TPUP_USEC_MAX (2000)
76
77 /**
78 * struct zpa2326_frequency - Hardware sampling frequency descriptor
79 * @hz : Frequency in Hertz.
80 * @odr: Output Data Rate word as expected by %ZPA2326_CTRL_REG3_REG.
81 */
82 struct zpa2326_frequency {
83 int hz;
84 u16 odr;
85 };
86
87 /*
88 * Keep these in strict ascending order: last array entry is expected to
89 * correspond to the highest sampling frequency.
90 */
91 static const struct zpa2326_frequency zpa2326_sampling_frequencies[] = {
92 { .hz = 1, .odr = 1 << ZPA2326_CTRL_REG3_ODR_SHIFT },
93 { .hz = 5, .odr = 5 << ZPA2326_CTRL_REG3_ODR_SHIFT },
94 { .hz = 11, .odr = 6 << ZPA2326_CTRL_REG3_ODR_SHIFT },
95 { .hz = 23, .odr = 7 << ZPA2326_CTRL_REG3_ODR_SHIFT },
96 };
97
98 /* Return the highest hardware sampling frequency available. */
zpa2326_highest_frequency(void)99 static const struct zpa2326_frequency *zpa2326_highest_frequency(void)
100 {
101 return &zpa2326_sampling_frequencies[
102 ARRAY_SIZE(zpa2326_sampling_frequencies) - 1];
103 }
104
105 /**
106 * struct zpa_private - Per-device internal private state
107 * @timestamp: Buffered samples ready datum.
108 * @regmap: Underlying I2C / SPI bus adapter used to abstract slave register
109 * accesses.
110 * @result: Allows sampling logic to get completion status of operations
111 * that interrupt handlers perform asynchronously.
112 * @data_ready: Interrupt handler uses this to wake user context up at sampling
113 * operation completion.
114 * @trigger: Optional hardware / interrupt driven trigger used to notify
115 * external devices a new sample is ready.
116 * @waken: Flag indicating whether or not device has just been powered on.
117 * @irq: Optional interrupt line: negative or zero if not declared into
118 * DT, in which case sampling logic keeps polling status register
119 * to detect completion.
120 * @frequency: Current hardware sampling frequency.
121 * @vref: Power / voltage reference.
122 * @vdd: Power supply.
123 */
124 struct zpa2326_private {
125 s64 timestamp;
126 struct regmap *regmap;
127 int result;
128 struct completion data_ready;
129 struct iio_trigger *trigger;
130 bool waken;
131 int irq;
132 const struct zpa2326_frequency *frequency;
133 struct regulator *vref;
134 struct regulator *vdd;
135 };
136
137 #define zpa2326_err(idev, fmt, ...) \
138 dev_err(idev->dev.parent, fmt "\n", ##__VA_ARGS__)
139
140 #define zpa2326_warn(idev, fmt, ...) \
141 dev_warn(idev->dev.parent, fmt "\n", ##__VA_ARGS__)
142
143 #define zpa2326_dbg(idev, fmt, ...) \
144 dev_dbg(idev->dev.parent, fmt "\n", ##__VA_ARGS__)
145
zpa2326_isreg_writeable(struct device * dev,unsigned int reg)146 bool zpa2326_isreg_writeable(struct device *dev, unsigned int reg)
147 {
148 switch (reg) {
149 case ZPA2326_REF_P_XL_REG:
150 case ZPA2326_REF_P_L_REG:
151 case ZPA2326_REF_P_H_REG:
152 case ZPA2326_RES_CONF_REG:
153 case ZPA2326_CTRL_REG0_REG:
154 case ZPA2326_CTRL_REG1_REG:
155 case ZPA2326_CTRL_REG2_REG:
156 case ZPA2326_CTRL_REG3_REG:
157 case ZPA2326_THS_P_LOW_REG:
158 case ZPA2326_THS_P_HIGH_REG:
159 return true;
160
161 default:
162 return false;
163 }
164 }
165 EXPORT_SYMBOL_GPL(zpa2326_isreg_writeable);
166
zpa2326_isreg_readable(struct device * dev,unsigned int reg)167 bool zpa2326_isreg_readable(struct device *dev, unsigned int reg)
168 {
169 switch (reg) {
170 case ZPA2326_REF_P_XL_REG:
171 case ZPA2326_REF_P_L_REG:
172 case ZPA2326_REF_P_H_REG:
173 case ZPA2326_DEVICE_ID_REG:
174 case ZPA2326_RES_CONF_REG:
175 case ZPA2326_CTRL_REG0_REG:
176 case ZPA2326_CTRL_REG1_REG:
177 case ZPA2326_CTRL_REG2_REG:
178 case ZPA2326_CTRL_REG3_REG:
179 case ZPA2326_INT_SOURCE_REG:
180 case ZPA2326_THS_P_LOW_REG:
181 case ZPA2326_THS_P_HIGH_REG:
182 case ZPA2326_STATUS_REG:
183 case ZPA2326_PRESS_OUT_XL_REG:
184 case ZPA2326_PRESS_OUT_L_REG:
185 case ZPA2326_PRESS_OUT_H_REG:
186 case ZPA2326_TEMP_OUT_L_REG:
187 case ZPA2326_TEMP_OUT_H_REG:
188 return true;
189
190 default:
191 return false;
192 }
193 }
194 EXPORT_SYMBOL_GPL(zpa2326_isreg_readable);
195
zpa2326_isreg_precious(struct device * dev,unsigned int reg)196 bool zpa2326_isreg_precious(struct device *dev, unsigned int reg)
197 {
198 switch (reg) {
199 case ZPA2326_INT_SOURCE_REG:
200 case ZPA2326_PRESS_OUT_H_REG:
201 return true;
202
203 default:
204 return false;
205 }
206 }
207 EXPORT_SYMBOL_GPL(zpa2326_isreg_precious);
208
209 /**
210 * zpa2326_enable_device() - Enable device, i.e. get out of low power mode.
211 * @indio_dev: The IIO device associated with the hardware to enable.
212 *
213 * Required to access complete register space and to perform any sampling
214 * or control operations.
215 *
216 * Return: Zero when successful, a negative error code otherwise.
217 */
zpa2326_enable_device(const struct iio_dev * indio_dev)218 static int zpa2326_enable_device(const struct iio_dev *indio_dev)
219 {
220 int err;
221
222 err = regmap_write(((struct zpa2326_private *)
223 iio_priv(indio_dev))->regmap,
224 ZPA2326_CTRL_REG0_REG, ZPA2326_CTRL_REG0_ENABLE);
225 if (err) {
226 zpa2326_err(indio_dev, "failed to enable device (%d)", err);
227 return err;
228 }
229
230 zpa2326_dbg(indio_dev, "enabled");
231
232 return 0;
233 }
234
235 /**
236 * zpa2326_sleep() - Disable device, i.e. switch to low power mode.
237 * @indio_dev: The IIO device associated with the hardware to disable.
238 *
239 * Only %ZPA2326_DEVICE_ID_REG and %ZPA2326_CTRL_REG0_REG registers may be
240 * accessed once device is in the disabled state.
241 *
242 * Return: Zero when successful, a negative error code otherwise.
243 */
zpa2326_sleep(const struct iio_dev * indio_dev)244 static int zpa2326_sleep(const struct iio_dev *indio_dev)
245 {
246 int err;
247
248 err = regmap_write(((struct zpa2326_private *)
249 iio_priv(indio_dev))->regmap,
250 ZPA2326_CTRL_REG0_REG, 0);
251 if (err) {
252 zpa2326_err(indio_dev, "failed to sleep (%d)", err);
253 return err;
254 }
255
256 zpa2326_dbg(indio_dev, "sleeping");
257
258 return 0;
259 }
260
261 /**
262 * zpa2326_reset_device() - Reset device to default hardware state.
263 * @indio_dev: The IIO device associated with the hardware to reset.
264 *
265 * Disable sampling and empty hardware FIFO.
266 * Device must be enabled before reset, i.e. not in low power mode.
267 *
268 * Return: Zero when successful, a negative error code otherwise.
269 */
zpa2326_reset_device(const struct iio_dev * indio_dev)270 static int zpa2326_reset_device(const struct iio_dev *indio_dev)
271 {
272 int err;
273
274 err = regmap_write(((struct zpa2326_private *)
275 iio_priv(indio_dev))->regmap,
276 ZPA2326_CTRL_REG2_REG, ZPA2326_CTRL_REG2_SWRESET);
277 if (err) {
278 zpa2326_err(indio_dev, "failed to reset device (%d)", err);
279 return err;
280 }
281
282 usleep_range(ZPA2326_TPUP_USEC_MIN, ZPA2326_TPUP_USEC_MAX);
283
284 zpa2326_dbg(indio_dev, "reset");
285
286 return 0;
287 }
288
289 /**
290 * zpa2326_start_oneshot() - Start a single sampling cycle, i.e. in one shot
291 * mode.
292 * @indio_dev: The IIO device associated with the sampling hardware.
293 *
294 * Device must have been previously enabled and configured for one shot mode.
295 * Device will be switched back to low power mode at end of cycle.
296 *
297 * Return: Zero when successful, a negative error code otherwise.
298 */
zpa2326_start_oneshot(const struct iio_dev * indio_dev)299 static int zpa2326_start_oneshot(const struct iio_dev *indio_dev)
300 {
301 int err;
302
303 err = regmap_write(((struct zpa2326_private *)
304 iio_priv(indio_dev))->regmap,
305 ZPA2326_CTRL_REG0_REG,
306 ZPA2326_CTRL_REG0_ENABLE |
307 ZPA2326_CTRL_REG0_ONE_SHOT);
308 if (err) {
309 zpa2326_err(indio_dev, "failed to start one shot cycle (%d)",
310 err);
311 return err;
312 }
313
314 zpa2326_dbg(indio_dev, "one shot cycle started");
315
316 return 0;
317 }
318
319 /**
320 * zpa2326_power_on() - Power on device to allow subsequent configuration.
321 * @indio_dev: The IIO device associated with the sampling hardware.
322 * @private: Internal private state related to @indio_dev.
323 *
324 * Sampling will be disabled, preventing strange things from happening in our
325 * back. Hardware FIFO content will be cleared.
326 * When successful, device will be left in the enabled state to allow further
327 * configuration.
328 *
329 * Return: Zero when successful, a negative error code otherwise.
330 */
zpa2326_power_on(const struct iio_dev * indio_dev,const struct zpa2326_private * private)331 static int zpa2326_power_on(const struct iio_dev *indio_dev,
332 const struct zpa2326_private *private)
333 {
334 int err;
335
336 err = regulator_enable(private->vref);
337 if (err)
338 return err;
339
340 err = regulator_enable(private->vdd);
341 if (err)
342 goto vref;
343
344 zpa2326_dbg(indio_dev, "powered on");
345
346 err = zpa2326_enable_device(indio_dev);
347 if (err)
348 goto vdd;
349
350 err = zpa2326_reset_device(indio_dev);
351 if (err)
352 goto sleep;
353
354 return 0;
355
356 sleep:
357 zpa2326_sleep(indio_dev);
358 vdd:
359 regulator_disable(private->vdd);
360 vref:
361 regulator_disable(private->vref);
362
363 zpa2326_dbg(indio_dev, "powered off");
364
365 return err;
366 }
367
368 /**
369 * zpa2326_power_off() - Power off device, i.e. disable attached power
370 * regulators.
371 * @indio_dev: The IIO device associated with the sampling hardware.
372 * @private: Internal private state related to @indio_dev.
373 *
374 * Return: Zero when successful, a negative error code otherwise.
375 */
zpa2326_power_off(const struct iio_dev * indio_dev,const struct zpa2326_private * private)376 static void zpa2326_power_off(const struct iio_dev *indio_dev,
377 const struct zpa2326_private *private)
378 {
379 regulator_disable(private->vdd);
380 regulator_disable(private->vref);
381
382 zpa2326_dbg(indio_dev, "powered off");
383 }
384
385 /**
386 * zpa2326_config_oneshot() - Setup device for one shot / on demand mode.
387 * @indio_dev: The IIO device associated with the sampling hardware.
388 * @irq: Optional interrupt line the hardware uses to notify new data
389 * samples are ready. Negative or zero values indicate no interrupts
390 * are available, meaning polling is required.
391 *
392 * Output Data Rate is configured for the highest possible rate so that
393 * conversion time and power consumption are reduced to a minimum.
394 * Note that hardware internal averaging machinery (not implemented in this
395 * driver) is not applicable in this mode.
396 *
397 * Device must have been previously enabled before calling
398 * zpa2326_config_oneshot().
399 *
400 * Return: Zero when successful, a negative error code otherwise.
401 */
zpa2326_config_oneshot(const struct iio_dev * indio_dev,int irq)402 static int zpa2326_config_oneshot(const struct iio_dev *indio_dev,
403 int irq)
404 {
405 struct regmap *regs = ((struct zpa2326_private *)
406 iio_priv(indio_dev))->regmap;
407 const struct zpa2326_frequency *freq = zpa2326_highest_frequency();
408 int err;
409
410 /* Setup highest available Output Data Rate for one shot mode. */
411 err = regmap_write(regs, ZPA2326_CTRL_REG3_REG, freq->odr);
412 if (err)
413 return err;
414
415 if (irq > 0) {
416 /* Request interrupt when new sample is available. */
417 err = regmap_write(regs, ZPA2326_CTRL_REG1_REG,
418 (u8)~ZPA2326_CTRL_REG1_MASK_DATA_READY);
419
420 if (err) {
421 dev_err(indio_dev->dev.parent,
422 "failed to setup one shot mode (%d)", err);
423 return err;
424 }
425 }
426
427 zpa2326_dbg(indio_dev, "one shot mode setup @%dHz", freq->hz);
428
429 return 0;
430 }
431
432 /**
433 * zpa2326_clear_fifo() - Clear remaining entries in hardware FIFO.
434 * @indio_dev: The IIO device associated with the sampling hardware.
435 * @min_count: Number of samples present within hardware FIFO.
436 *
437 * @min_count argument is a hint corresponding to the known minimum number of
438 * samples currently living in the FIFO. This allows to reduce the number of bus
439 * accesses by skipping status register read operation as long as we know for
440 * sure there are still entries left.
441 *
442 * Return: Zero when successful, a negative error code otherwise.
443 */
zpa2326_clear_fifo(const struct iio_dev * indio_dev,unsigned int min_count)444 static int zpa2326_clear_fifo(const struct iio_dev *indio_dev,
445 unsigned int min_count)
446 {
447 struct regmap *regs = ((struct zpa2326_private *)
448 iio_priv(indio_dev))->regmap;
449 int err;
450 unsigned int val;
451
452 if (!min_count) {
453 /*
454 * No hint: read status register to determine whether FIFO is
455 * empty or not.
456 */
457 err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
458
459 if (err < 0)
460 goto err;
461
462 if (val & ZPA2326_STATUS_FIFO_E)
463 /* Fifo is empty: nothing to trash. */
464 return 0;
465 }
466
467 /* Clear FIFO. */
468 do {
469 /*
470 * A single fetch from pressure MSB register is enough to pop
471 * values out of FIFO.
472 */
473 err = regmap_read(regs, ZPA2326_PRESS_OUT_H_REG, &val);
474 if (err < 0)
475 goto err;
476
477 if (min_count) {
478 /*
479 * We know for sure there are at least min_count entries
480 * left in FIFO. Skip status register read.
481 */
482 min_count--;
483 continue;
484 }
485
486 err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
487 if (err < 0)
488 goto err;
489
490 } while (!(val & ZPA2326_STATUS_FIFO_E));
491
492 zpa2326_dbg(indio_dev, "FIFO cleared");
493
494 return 0;
495
496 err:
497 zpa2326_err(indio_dev, "failed to clear FIFO (%d)", err);
498
499 return err;
500 }
501
502 /**
503 * zpa2326_dequeue_pressure() - Retrieve the most recent pressure sample from
504 * hardware FIFO.
505 * @indio_dev: The IIO device associated with the sampling hardware.
506 * @pressure: Sampled pressure output.
507 *
508 * Note that ZPA2326 hardware FIFO stores pressure samples only.
509 *
510 * Return: Zero when successful, a negative error code otherwise.
511 */
zpa2326_dequeue_pressure(const struct iio_dev * indio_dev,u32 * pressure)512 static int zpa2326_dequeue_pressure(const struct iio_dev *indio_dev,
513 u32 *pressure)
514 {
515 struct regmap *regs = ((struct zpa2326_private *)
516 iio_priv(indio_dev))->regmap;
517 unsigned int val;
518 int err;
519 int cleared = -1;
520
521 err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
522 if (err < 0)
523 return err;
524
525 *pressure = 0;
526
527 if (val & ZPA2326_STATUS_P_OR) {
528 /*
529 * Fifo overrun : first sample dequeued from FIFO is the
530 * newest.
531 */
532 zpa2326_warn(indio_dev, "FIFO overflow");
533
534 err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, pressure,
535 3);
536 if (err)
537 return err;
538
539 #define ZPA2326_FIFO_DEPTH (16U)
540 /* Hardware FIFO may hold no more than 16 pressure samples. */
541 return zpa2326_clear_fifo(indio_dev, ZPA2326_FIFO_DEPTH - 1);
542 }
543
544 /*
545 * Fifo has not overflown : retrieve newest sample. We need to pop
546 * values out until FIFO is empty : last fetched pressure is the newest.
547 * In nominal cases, we should find a single queued sample only.
548 */
549 do {
550 err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, pressure,
551 3);
552 if (err)
553 return err;
554
555 err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
556 if (err < 0)
557 return err;
558
559 cleared++;
560 } while (!(val & ZPA2326_STATUS_FIFO_E));
561
562 if (cleared)
563 /*
564 * Samples were pushed by hardware during previous rounds but we
565 * didn't consume them fast enough: inform user.
566 */
567 zpa2326_dbg(indio_dev, "cleared %d FIFO entries", cleared);
568
569 return 0;
570 }
571
572 /**
573 * zpa2326_fill_sample_buffer() - Enqueue new channel samples to IIO buffer.
574 * @indio_dev: The IIO device associated with the sampling hardware.
575 * @private: Internal private state related to @indio_dev.
576 *
577 * Return: Zero when successful, a negative error code otherwise.
578 */
zpa2326_fill_sample_buffer(struct iio_dev * indio_dev,const struct zpa2326_private * private)579 static int zpa2326_fill_sample_buffer(struct iio_dev *indio_dev,
580 const struct zpa2326_private *private)
581 {
582 struct {
583 u32 pressure;
584 u16 temperature;
585 u64 timestamp;
586 } sample;
587 int err;
588
589 if (test_bit(0, indio_dev->active_scan_mask)) {
590 /* Get current pressure from hardware FIFO. */
591 err = zpa2326_dequeue_pressure(indio_dev, &sample.pressure);
592 if (err) {
593 zpa2326_warn(indio_dev, "failed to fetch pressure (%d)",
594 err);
595 return err;
596 }
597 }
598
599 if (test_bit(1, indio_dev->active_scan_mask)) {
600 /* Get current temperature. */
601 err = regmap_bulk_read(private->regmap, ZPA2326_TEMP_OUT_L_REG,
602 &sample.temperature, 2);
603 if (err) {
604 zpa2326_warn(indio_dev,
605 "failed to fetch temperature (%d)", err);
606 return err;
607 }
608 }
609
610 /*
611 * Now push samples using timestamp stored either :
612 * - by hardware interrupt handler if interrupt is available: see
613 * zpa2326_handle_irq(),
614 * - or oneshot completion polling machinery : see
615 * zpa2326_trigger_handler().
616 */
617 zpa2326_dbg(indio_dev, "filling raw samples buffer");
618
619 iio_push_to_buffers_with_timestamp(indio_dev, &sample,
620 private->timestamp);
621
622 return 0;
623 }
624
625 #ifdef CONFIG_PM
zpa2326_runtime_suspend(struct device * parent)626 static int zpa2326_runtime_suspend(struct device *parent)
627 {
628 const struct iio_dev *indio_dev = dev_get_drvdata(parent);
629
630 if (pm_runtime_autosuspend_expiration(parent))
631 /* Userspace changed autosuspend delay. */
632 return -EAGAIN;
633
634 zpa2326_power_off(indio_dev, iio_priv(indio_dev));
635
636 return 0;
637 }
638
zpa2326_runtime_resume(struct device * parent)639 static int zpa2326_runtime_resume(struct device *parent)
640 {
641 const struct iio_dev *indio_dev = dev_get_drvdata(parent);
642
643 return zpa2326_power_on(indio_dev, iio_priv(indio_dev));
644 }
645
646 const struct dev_pm_ops zpa2326_pm_ops = {
647 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
648 pm_runtime_force_resume)
649 SET_RUNTIME_PM_OPS(zpa2326_runtime_suspend, zpa2326_runtime_resume,
650 NULL)
651 };
652 EXPORT_SYMBOL_GPL(zpa2326_pm_ops);
653
654 /**
655 * zpa2326_resume() - Request the PM layer to power supply the device.
656 * @indio_dev: The IIO device associated with the sampling hardware.
657 *
658 * Return:
659 * < 0 - a negative error code meaning failure ;
660 * 0 - success, device has just been powered up ;
661 * 1 - success, device was already powered.
662 */
zpa2326_resume(const struct iio_dev * indio_dev)663 static int zpa2326_resume(const struct iio_dev *indio_dev)
664 {
665 int err;
666
667 err = pm_runtime_get_sync(indio_dev->dev.parent);
668 if (err < 0) {
669 pm_runtime_put(indio_dev->dev.parent);
670 return err;
671 }
672
673 if (err > 0) {
674 /*
675 * Device was already power supplied: get it out of low power
676 * mode and inform caller.
677 */
678 zpa2326_enable_device(indio_dev);
679 return 1;
680 }
681
682 /* Inform caller device has just been brought back to life. */
683 return 0;
684 }
685
686 /**
687 * zpa2326_suspend() - Schedule a power down using autosuspend feature of PM
688 * layer.
689 * @indio_dev: The IIO device associated with the sampling hardware.
690 *
691 * Device is switched to low power mode at first to save power even when
692 * attached regulator is a "dummy" one.
693 */
zpa2326_suspend(struct iio_dev * indio_dev)694 static void zpa2326_suspend(struct iio_dev *indio_dev)
695 {
696 struct device *parent = indio_dev->dev.parent;
697
698 zpa2326_sleep(indio_dev);
699
700 pm_runtime_mark_last_busy(parent);
701 pm_runtime_put_autosuspend(parent);
702 }
703
zpa2326_init_runtime(struct device * parent)704 static void zpa2326_init_runtime(struct device *parent)
705 {
706 pm_runtime_get_noresume(parent);
707 pm_runtime_set_active(parent);
708 pm_runtime_enable(parent);
709 pm_runtime_set_autosuspend_delay(parent, 1000);
710 pm_runtime_use_autosuspend(parent);
711 pm_runtime_mark_last_busy(parent);
712 pm_runtime_put_autosuspend(parent);
713 }
714
zpa2326_fini_runtime(struct device * parent)715 static void zpa2326_fini_runtime(struct device *parent)
716 {
717 pm_runtime_disable(parent);
718 pm_runtime_set_suspended(parent);
719 }
720 #else /* !CONFIG_PM */
zpa2326_resume(const struct iio_dev * indio_dev)721 static int zpa2326_resume(const struct iio_dev *indio_dev)
722 {
723 zpa2326_enable_device(indio_dev);
724
725 return 0;
726 }
727
zpa2326_suspend(struct iio_dev * indio_dev)728 static void zpa2326_suspend(struct iio_dev *indio_dev)
729 {
730 zpa2326_sleep(indio_dev);
731 }
732
733 #define zpa2326_init_runtime(_parent)
734 #define zpa2326_fini_runtime(_parent)
735 #endif /* !CONFIG_PM */
736
737 /**
738 * zpa2326_handle_irq() - Process hardware interrupts.
739 * @irq: Interrupt line the hardware uses to notify new data has arrived.
740 * @data: The IIO device associated with the sampling hardware.
741 *
742 * Timestamp buffered samples as soon as possible then schedule threaded bottom
743 * half.
744 *
745 * Return: Always successful.
746 */
zpa2326_handle_irq(int irq,void * data)747 static irqreturn_t zpa2326_handle_irq(int irq, void *data)
748 {
749 struct iio_dev *indio_dev = data;
750
751 if (iio_buffer_enabled(indio_dev)) {
752 /* Timestamping needed for buffered sampling only. */
753 ((struct zpa2326_private *)
754 iio_priv(indio_dev))->timestamp = iio_get_time_ns(indio_dev);
755 }
756
757 return IRQ_WAKE_THREAD;
758 }
759
760 /**
761 * zpa2326_handle_threaded_irq() - Interrupt bottom-half handler.
762 * @irq: Interrupt line the hardware uses to notify new data has arrived.
763 * @data: The IIO device associated with the sampling hardware.
764 *
765 * Mainly ensures interrupt is caused by a real "new sample available"
766 * condition. This relies upon the ability to perform blocking / sleeping bus
767 * accesses to slave's registers. This is why zpa2326_handle_threaded_irq() is
768 * called from within a thread, i.e. not called from hard interrupt context.
769 *
770 * When device is using its own internal hardware trigger in continuous sampling
771 * mode, data are available into hardware FIFO once interrupt has occurred. All
772 * we have to do is to dispatch the trigger, which in turn will fetch data and
773 * fill IIO buffer.
774 *
775 * When not using its own internal hardware trigger, the device has been
776 * configured in one-shot mode either by an external trigger or the IIO read_raw
777 * hook. This means one of the latter is currently waiting for sampling
778 * completion, in which case we must simply wake it up.
779 *
780 * See zpa2326_trigger_handler().
781 *
782 * Return:
783 * %IRQ_NONE - no consistent interrupt happened ;
784 * %IRQ_HANDLED - there was new samples available.
785 */
zpa2326_handle_threaded_irq(int irq,void * data)786 static irqreturn_t zpa2326_handle_threaded_irq(int irq, void *data)
787 {
788 struct iio_dev *indio_dev = data;
789 struct zpa2326_private *priv = iio_priv(indio_dev);
790 unsigned int val;
791 bool cont;
792 irqreturn_t ret = IRQ_NONE;
793
794 /*
795 * Are we using our own internal trigger in triggered buffer mode, i.e.,
796 * currently working in continuous sampling mode ?
797 */
798 cont = (iio_buffer_enabled(indio_dev) &&
799 iio_trigger_using_own(indio_dev));
800
801 /*
802 * Device works according to a level interrupt scheme: reading interrupt
803 * status de-asserts interrupt line.
804 */
805 priv->result = regmap_read(priv->regmap, ZPA2326_INT_SOURCE_REG, &val);
806 if (priv->result < 0) {
807 if (cont)
808 return IRQ_NONE;
809
810 goto complete;
811 }
812
813 /* Data ready is the only interrupt source we requested. */
814 if (!(val & ZPA2326_INT_SOURCE_DATA_READY)) {
815 /*
816 * Interrupt happened but no new sample available: likely caused
817 * by spurious interrupts, in which case, returning IRQ_NONE
818 * allows to benefit from the generic spurious interrupts
819 * handling.
820 */
821 zpa2326_warn(indio_dev, "unexpected interrupt status %02x",
822 val);
823
824 if (cont)
825 return IRQ_NONE;
826
827 priv->result = -ENODATA;
828 goto complete;
829 }
830
831 /* New sample available: dispatch internal trigger consumers. */
832 iio_trigger_poll_chained(priv->trigger);
833
834 if (cont)
835 /*
836 * Internal hardware trigger has been scheduled above : it will
837 * fetch data on its own.
838 */
839 return IRQ_HANDLED;
840
841 ret = IRQ_HANDLED;
842
843 complete:
844 /*
845 * Wake up direct or externaly triggered buffer mode waiters: see
846 * zpa2326_sample_oneshot() and zpa2326_trigger_handler().
847 */
848 complete(&priv->data_ready);
849
850 return ret;
851 }
852
853 /**
854 * zpa2326_wait_oneshot_completion() - Wait for oneshot data ready interrupt.
855 * @indio_dev: The IIO device associated with the sampling hardware.
856 * @private: Internal private state related to @indio_dev.
857 *
858 * Return: Zero when successful, a negative error code otherwise.
859 */
zpa2326_wait_oneshot_completion(const struct iio_dev * indio_dev,struct zpa2326_private * private)860 static int zpa2326_wait_oneshot_completion(const struct iio_dev *indio_dev,
861 struct zpa2326_private *private)
862 {
863 unsigned int val;
864 long timeout;
865
866 zpa2326_dbg(indio_dev, "waiting for one shot completion interrupt");
867
868 timeout = wait_for_completion_interruptible_timeout(
869 &private->data_ready, ZPA2326_CONVERSION_JIFFIES);
870 if (timeout > 0)
871 /*
872 * Interrupt handler completed before timeout: return operation
873 * status.
874 */
875 return private->result;
876
877 /* Clear all interrupts just to be sure. */
878 regmap_read(private->regmap, ZPA2326_INT_SOURCE_REG, &val);
879
880 if (!timeout) {
881 /* Timed out. */
882 zpa2326_warn(indio_dev, "no one shot interrupt occurred (%ld)",
883 timeout);
884 return -ETIME;
885 }
886
887 zpa2326_warn(indio_dev, "wait for one shot interrupt cancelled");
888 return -ERESTARTSYS;
889 }
890
zpa2326_init_managed_irq(struct device * parent,struct iio_dev * indio_dev,struct zpa2326_private * private,int irq)891 static int zpa2326_init_managed_irq(struct device *parent,
892 struct iio_dev *indio_dev,
893 struct zpa2326_private *private,
894 int irq)
895 {
896 int err;
897
898 private->irq = irq;
899
900 if (irq <= 0) {
901 /*
902 * Platform declared no interrupt line: device will be polled
903 * for data availability.
904 */
905 dev_info(parent, "no interrupt found, running in polling mode");
906 return 0;
907 }
908
909 init_completion(&private->data_ready);
910
911 /* Request handler to be scheduled into threaded interrupt context. */
912 err = devm_request_threaded_irq(parent, irq, zpa2326_handle_irq,
913 zpa2326_handle_threaded_irq,
914 IRQF_TRIGGER_RISING | IRQF_ONESHOT,
915 dev_name(parent), indio_dev);
916 if (err) {
917 dev_err(parent, "failed to request interrupt %d (%d)", irq,
918 err);
919 return err;
920 }
921
922 dev_info(parent, "using interrupt %d", irq);
923
924 return 0;
925 }
926
927 /**
928 * zpa2326_poll_oneshot_completion() - Actively poll for one shot data ready.
929 * @indio_dev: The IIO device associated with the sampling hardware.
930 *
931 * Loop over registers content to detect end of sampling cycle. Used when DT
932 * declared no valid interrupt lines.
933 *
934 * Return: Zero when successful, a negative error code otherwise.
935 */
zpa2326_poll_oneshot_completion(const struct iio_dev * indio_dev)936 static int zpa2326_poll_oneshot_completion(const struct iio_dev *indio_dev)
937 {
938 unsigned long tmout = jiffies + ZPA2326_CONVERSION_JIFFIES;
939 struct regmap *regs = ((struct zpa2326_private *)
940 iio_priv(indio_dev))->regmap;
941 unsigned int val;
942 int err;
943
944 zpa2326_dbg(indio_dev, "polling for one shot completion");
945
946 /*
947 * At least, 100 ms is needed for the device to complete its one-shot
948 * cycle.
949 */
950 if (msleep_interruptible(100))
951 return -ERESTARTSYS;
952
953 /* Poll for conversion completion in hardware. */
954 while (true) {
955 err = regmap_read(regs, ZPA2326_CTRL_REG0_REG, &val);
956 if (err < 0)
957 goto err;
958
959 if (!(val & ZPA2326_CTRL_REG0_ONE_SHOT))
960 /* One-shot bit self clears at conversion end. */
961 break;
962
963 if (time_after(jiffies, tmout)) {
964 /* Prevent from waiting forever : let's time out. */
965 err = -ETIME;
966 goto err;
967 }
968
969 usleep_range(10000, 20000);
970 }
971
972 /*
973 * In oneshot mode, pressure sample availability guarantees that
974 * temperature conversion has also completed : just check pressure
975 * status bit to keep things simple.
976 */
977 err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
978 if (err < 0)
979 goto err;
980
981 if (!(val & ZPA2326_STATUS_P_DA)) {
982 /* No sample available. */
983 err = -ENODATA;
984 goto err;
985 }
986
987 return 0;
988
989 err:
990 zpa2326_warn(indio_dev, "failed to poll one shot completion (%d)", err);
991
992 return err;
993 }
994
995 /**
996 * zpa2326_fetch_raw_sample() - Retrieve a raw sample and convert it to CPU
997 * endianness.
998 * @indio_dev: The IIO device associated with the sampling hardware.
999 * @type: Type of measurement / channel to fetch from.
1000 * @value: Sample output.
1001 *
1002 * Return: Zero when successful, a negative error code otherwise.
1003 */
zpa2326_fetch_raw_sample(const struct iio_dev * indio_dev,enum iio_chan_type type,int * value)1004 static int zpa2326_fetch_raw_sample(const struct iio_dev *indio_dev,
1005 enum iio_chan_type type,
1006 int *value)
1007 {
1008 struct regmap *regs = ((struct zpa2326_private *)
1009 iio_priv(indio_dev))->regmap;
1010 int err;
1011 u8 v[3];
1012
1013 switch (type) {
1014 case IIO_PRESSURE:
1015 zpa2326_dbg(indio_dev, "fetching raw pressure sample");
1016
1017 err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, v, sizeof(v));
1018 if (err) {
1019 zpa2326_warn(indio_dev, "failed to fetch pressure (%d)",
1020 err);
1021 return err;
1022 }
1023
1024 *value = get_unaligned_le24(&v[0]);
1025
1026 return IIO_VAL_INT;
1027
1028 case IIO_TEMP:
1029 zpa2326_dbg(indio_dev, "fetching raw temperature sample");
1030
1031 err = regmap_bulk_read(regs, ZPA2326_TEMP_OUT_L_REG, value, 2);
1032 if (err) {
1033 zpa2326_warn(indio_dev,
1034 "failed to fetch temperature (%d)", err);
1035 return err;
1036 }
1037
1038 /* Temperature is a 16 bits wide little-endian signed int. */
1039 *value = (int)le16_to_cpup((__le16 *)value);
1040
1041 return IIO_VAL_INT;
1042
1043 default:
1044 return -EINVAL;
1045 }
1046 }
1047
1048 /**
1049 * zpa2326_sample_oneshot() - Perform a complete one shot sampling cycle.
1050 * @indio_dev: The IIO device associated with the sampling hardware.
1051 * @type: Type of measurement / channel to fetch from.
1052 * @value: Sample output.
1053 *
1054 * Return: Zero when successful, a negative error code otherwise.
1055 */
zpa2326_sample_oneshot(struct iio_dev * indio_dev,enum iio_chan_type type,int * value)1056 static int zpa2326_sample_oneshot(struct iio_dev *indio_dev,
1057 enum iio_chan_type type,
1058 int *value)
1059 {
1060 int ret;
1061 struct zpa2326_private *priv;
1062
1063 ret = iio_device_claim_direct_mode(indio_dev);
1064 if (ret)
1065 return ret;
1066
1067 ret = zpa2326_resume(indio_dev);
1068 if (ret < 0)
1069 goto release;
1070
1071 priv = iio_priv(indio_dev);
1072
1073 if (ret > 0) {
1074 /*
1075 * We were already power supplied. Just clear hardware FIFO to
1076 * get rid of samples acquired during previous rounds (if any).
1077 * Sampling operation always generates both temperature and
1078 * pressure samples. The latter are always enqueued into
1079 * hardware FIFO. This may lead to situations were pressure
1080 * samples still sit into FIFO when previous cycle(s) fetched
1081 * temperature data only.
1082 * Hence, we need to clear hardware FIFO content to prevent from
1083 * getting outdated values at the end of current cycle.
1084 */
1085 if (type == IIO_PRESSURE) {
1086 ret = zpa2326_clear_fifo(indio_dev, 0);
1087 if (ret)
1088 goto suspend;
1089 }
1090 } else {
1091 /*
1092 * We have just been power supplied, i.e. device is in default
1093 * "out of reset" state, meaning we need to reconfigure it
1094 * entirely.
1095 */
1096 ret = zpa2326_config_oneshot(indio_dev, priv->irq);
1097 if (ret)
1098 goto suspend;
1099 }
1100
1101 /* Start a sampling cycle in oneshot mode. */
1102 ret = zpa2326_start_oneshot(indio_dev);
1103 if (ret)
1104 goto suspend;
1105
1106 /* Wait for sampling cycle to complete. */
1107 if (priv->irq > 0)
1108 ret = zpa2326_wait_oneshot_completion(indio_dev, priv);
1109 else
1110 ret = zpa2326_poll_oneshot_completion(indio_dev);
1111
1112 if (ret)
1113 goto suspend;
1114
1115 /* Retrieve raw sample value and convert it to CPU endianness. */
1116 ret = zpa2326_fetch_raw_sample(indio_dev, type, value);
1117
1118 suspend:
1119 zpa2326_suspend(indio_dev);
1120 release:
1121 iio_device_release_direct_mode(indio_dev);
1122
1123 return ret;
1124 }
1125
1126 /**
1127 * zpa2326_trigger_handler() - Perform an IIO buffered sampling round in one
1128 * shot mode.
1129 * @irq: The software interrupt assigned to @data
1130 * @data: The IIO poll function dispatched by external trigger our device is
1131 * attached to.
1132 *
1133 * Bottom-half handler called by the IIO trigger to which our device is
1134 * currently attached. Allows us to synchronize this device buffered sampling
1135 * either with external events (such as timer expiration, external device sample
1136 * ready, etc...) or with its own interrupt (internal hardware trigger).
1137 *
1138 * When using an external trigger, basically run the same sequence of operations
1139 * as for zpa2326_sample_oneshot() with the following hereafter. Hardware FIFO
1140 * is not cleared since already done at buffering enable time and samples
1141 * dequeueing always retrieves the most recent value.
1142 *
1143 * Otherwise, when internal hardware trigger has dispatched us, just fetch data
1144 * from hardware FIFO.
1145 *
1146 * Fetched data will pushed unprocessed to IIO buffer since samples conversion
1147 * is delegated to userspace in buffered mode (endianness, etc...).
1148 *
1149 * Return:
1150 * %IRQ_NONE - no consistent interrupt happened ;
1151 * %IRQ_HANDLED - there was new samples available.
1152 */
zpa2326_trigger_handler(int irq,void * data)1153 static irqreturn_t zpa2326_trigger_handler(int irq, void *data)
1154 {
1155 struct iio_dev *indio_dev = ((struct iio_poll_func *)
1156 data)->indio_dev;
1157 struct zpa2326_private *priv = iio_priv(indio_dev);
1158 bool cont;
1159
1160 /*
1161 * We have been dispatched, meaning we are in triggered buffer mode.
1162 * Using our own internal trigger implies we are currently in continuous
1163 * hardware sampling mode.
1164 */
1165 cont = iio_trigger_using_own(indio_dev);
1166
1167 if (!cont) {
1168 /* On demand sampling : start a one shot cycle. */
1169 if (zpa2326_start_oneshot(indio_dev))
1170 goto out;
1171
1172 /* Wait for sampling cycle to complete. */
1173 if (priv->irq <= 0) {
1174 /* No interrupt available: poll for completion. */
1175 if (zpa2326_poll_oneshot_completion(indio_dev))
1176 goto out;
1177
1178 /* Only timestamp sample once it is ready. */
1179 priv->timestamp = iio_get_time_ns(indio_dev);
1180 } else {
1181 /* Interrupt handlers will timestamp for us. */
1182 if (zpa2326_wait_oneshot_completion(indio_dev, priv))
1183 goto out;
1184 }
1185 }
1186
1187 /* Enqueue to IIO buffer / userspace. */
1188 zpa2326_fill_sample_buffer(indio_dev, priv);
1189
1190 out:
1191 if (!cont)
1192 /* Don't switch to low power if sampling continuously. */
1193 zpa2326_sleep(indio_dev);
1194
1195 /* Inform attached trigger we are done. */
1196 iio_trigger_notify_done(indio_dev->trig);
1197
1198 return IRQ_HANDLED;
1199 }
1200
1201 /**
1202 * zpa2326_preenable_buffer() - Prepare device for configuring triggered
1203 * sampling
1204 * modes.
1205 * @indio_dev: The IIO device associated with the sampling hardware.
1206 *
1207 * Basically power up device.
1208 * Called with IIO device's lock held.
1209 *
1210 * Return: Zero when successful, a negative error code otherwise.
1211 */
zpa2326_preenable_buffer(struct iio_dev * indio_dev)1212 static int zpa2326_preenable_buffer(struct iio_dev *indio_dev)
1213 {
1214 int ret = zpa2326_resume(indio_dev);
1215
1216 if (ret < 0)
1217 return ret;
1218
1219 /* Tell zpa2326_postenable_buffer() if we have just been powered on. */
1220 ((struct zpa2326_private *)
1221 iio_priv(indio_dev))->waken = iio_priv(indio_dev);
1222
1223 return 0;
1224 }
1225
1226 /**
1227 * zpa2326_postenable_buffer() - Configure device for triggered sampling.
1228 * @indio_dev: The IIO device associated with the sampling hardware.
1229 *
1230 * Basically setup one-shot mode if plugging external trigger.
1231 * Otherwise, let internal trigger configure continuous sampling :
1232 * see zpa2326_set_trigger_state().
1233 *
1234 * If an error is returned, IIO layer will call our postdisable hook for us,
1235 * i.e. no need to explicitly power device off here.
1236 * Called with IIO device's lock held.
1237 *
1238 * Called with IIO device's lock held.
1239 *
1240 * Return: Zero when successful, a negative error code otherwise.
1241 */
zpa2326_postenable_buffer(struct iio_dev * indio_dev)1242 static int zpa2326_postenable_buffer(struct iio_dev *indio_dev)
1243 {
1244 const struct zpa2326_private *priv = iio_priv(indio_dev);
1245 int err;
1246
1247 if (!priv->waken) {
1248 /*
1249 * We were already power supplied. Just clear hardware FIFO to
1250 * get rid of samples acquired during previous rounds (if any).
1251 */
1252 err = zpa2326_clear_fifo(indio_dev, 0);
1253 if (err) {
1254 zpa2326_err(indio_dev,
1255 "failed to enable buffering (%d)", err);
1256 return err;
1257 }
1258 }
1259
1260 if (!iio_trigger_using_own(indio_dev) && priv->waken) {
1261 /*
1262 * We are using an external trigger and we have just been
1263 * powered up: reconfigure one-shot mode.
1264 */
1265 err = zpa2326_config_oneshot(indio_dev, priv->irq);
1266 if (err) {
1267 zpa2326_err(indio_dev,
1268 "failed to enable buffering (%d)", err);
1269 return err;
1270 }
1271 }
1272
1273 return 0;
1274 }
1275
zpa2326_postdisable_buffer(struct iio_dev * indio_dev)1276 static int zpa2326_postdisable_buffer(struct iio_dev *indio_dev)
1277 {
1278 zpa2326_suspend(indio_dev);
1279
1280 return 0;
1281 }
1282
1283 static const struct iio_buffer_setup_ops zpa2326_buffer_setup_ops = {
1284 .preenable = zpa2326_preenable_buffer,
1285 .postenable = zpa2326_postenable_buffer,
1286 .postdisable = zpa2326_postdisable_buffer
1287 };
1288
1289 /**
1290 * zpa2326_set_trigger_state() - Start / stop continuous sampling.
1291 * @trig: The trigger being attached to IIO device associated with the sampling
1292 * hardware.
1293 * @state: Tell whether to start (true) or stop (false)
1294 *
1295 * Basically enable / disable hardware continuous sampling mode.
1296 *
1297 * Called with IIO device's lock held at postenable() or predisable() time.
1298 *
1299 * Return: Zero when successful, a negative error code otherwise.
1300 */
zpa2326_set_trigger_state(struct iio_trigger * trig,bool state)1301 static int zpa2326_set_trigger_state(struct iio_trigger *trig, bool state)
1302 {
1303 const struct iio_dev *indio_dev = dev_get_drvdata(
1304 trig->dev.parent);
1305 const struct zpa2326_private *priv = iio_priv(indio_dev);
1306 int err;
1307
1308 if (!state) {
1309 /*
1310 * Switch trigger off : in case of failure, interrupt is left
1311 * disabled in order to prevent handler from accessing released
1312 * resources.
1313 */
1314 unsigned int val;
1315
1316 /*
1317 * As device is working in continuous mode, handlers may be
1318 * accessing resources we are currently freeing...
1319 * Prevent this by disabling interrupt handlers and ensure
1320 * the device will generate no more interrupts unless explicitly
1321 * required to, i.e. by restoring back to default one shot mode.
1322 */
1323 disable_irq(priv->irq);
1324
1325 /*
1326 * Disable continuous sampling mode to restore settings for
1327 * one shot / direct sampling operations.
1328 */
1329 err = regmap_write(priv->regmap, ZPA2326_CTRL_REG3_REG,
1330 zpa2326_highest_frequency()->odr);
1331 if (err)
1332 return err;
1333
1334 /*
1335 * Now that device won't generate interrupts on its own,
1336 * acknowledge any currently active interrupts (may happen on
1337 * rare occasions while stopping continuous mode).
1338 */
1339 err = regmap_read(priv->regmap, ZPA2326_INT_SOURCE_REG, &val);
1340 if (err < 0)
1341 return err;
1342
1343 /*
1344 * Re-enable interrupts only if we can guarantee the device will
1345 * generate no more interrupts to prevent handlers from
1346 * accessing released resources.
1347 */
1348 enable_irq(priv->irq);
1349
1350 zpa2326_dbg(indio_dev, "continuous mode stopped");
1351 } else {
1352 /*
1353 * Switch trigger on : start continuous sampling at required
1354 * frequency.
1355 */
1356
1357 if (priv->waken) {
1358 /* Enable interrupt if getting out of reset. */
1359 err = regmap_write(priv->regmap, ZPA2326_CTRL_REG1_REG,
1360 (u8)
1361 ~ZPA2326_CTRL_REG1_MASK_DATA_READY);
1362 if (err)
1363 return err;
1364 }
1365
1366 /* Enable continuous sampling at specified frequency. */
1367 err = regmap_write(priv->regmap, ZPA2326_CTRL_REG3_REG,
1368 ZPA2326_CTRL_REG3_ENABLE_MEAS |
1369 priv->frequency->odr);
1370 if (err)
1371 return err;
1372
1373 zpa2326_dbg(indio_dev, "continuous mode setup @%dHz",
1374 priv->frequency->hz);
1375 }
1376
1377 return 0;
1378 }
1379
1380 static const struct iio_trigger_ops zpa2326_trigger_ops = {
1381 .set_trigger_state = zpa2326_set_trigger_state,
1382 };
1383
1384 /**
1385 * zpa2326_init_trigger() - Create an interrupt driven / hardware trigger
1386 * allowing to notify external devices a new sample is
1387 * ready.
1388 * @parent: Hardware sampling device @indio_dev is a child of.
1389 * @indio_dev: The IIO device associated with the sampling hardware.
1390 * @private: Internal private state related to @indio_dev.
1391 * @irq: Optional interrupt line the hardware uses to notify new data
1392 * samples are ready. Negative or zero values indicate no interrupts
1393 * are available, meaning polling is required.
1394 *
1395 * Only relevant when DT declares a valid interrupt line.
1396 *
1397 * Return: Zero when successful, a negative error code otherwise.
1398 */
zpa2326_init_managed_trigger(struct device * parent,struct iio_dev * indio_dev,struct zpa2326_private * private,int irq)1399 static int zpa2326_init_managed_trigger(struct device *parent,
1400 struct iio_dev *indio_dev,
1401 struct zpa2326_private *private,
1402 int irq)
1403 {
1404 struct iio_trigger *trigger;
1405 int ret;
1406
1407 if (irq <= 0)
1408 return 0;
1409
1410 trigger = devm_iio_trigger_alloc(parent, "%s-dev%d",
1411 indio_dev->name, indio_dev->id);
1412 if (!trigger)
1413 return -ENOMEM;
1414
1415 /* Basic setup. */
1416 trigger->dev.parent = parent;
1417 trigger->ops = &zpa2326_trigger_ops;
1418
1419 private->trigger = trigger;
1420
1421 /* Register to triggers space. */
1422 ret = devm_iio_trigger_register(parent, trigger);
1423 if (ret)
1424 dev_err(parent, "failed to register hardware trigger (%d)",
1425 ret);
1426
1427 return ret;
1428 }
1429
zpa2326_get_frequency(const struct iio_dev * indio_dev)1430 static int zpa2326_get_frequency(const struct iio_dev *indio_dev)
1431 {
1432 return ((struct zpa2326_private *)iio_priv(indio_dev))->frequency->hz;
1433 }
1434
zpa2326_set_frequency(struct iio_dev * indio_dev,int hz)1435 static int zpa2326_set_frequency(struct iio_dev *indio_dev, int hz)
1436 {
1437 struct zpa2326_private *priv = iio_priv(indio_dev);
1438 int freq;
1439 int err;
1440
1441 /* Check if requested frequency is supported. */
1442 for (freq = 0; freq < ARRAY_SIZE(zpa2326_sampling_frequencies); freq++)
1443 if (zpa2326_sampling_frequencies[freq].hz == hz)
1444 break;
1445 if (freq == ARRAY_SIZE(zpa2326_sampling_frequencies))
1446 return -EINVAL;
1447
1448 /* Don't allow changing frequency if buffered sampling is ongoing. */
1449 err = iio_device_claim_direct_mode(indio_dev);
1450 if (err)
1451 return err;
1452
1453 priv->frequency = &zpa2326_sampling_frequencies[freq];
1454
1455 iio_device_release_direct_mode(indio_dev);
1456
1457 return 0;
1458 }
1459
1460 /* Expose supported hardware sampling frequencies (Hz) through sysfs. */
1461 static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("1 5 11 23");
1462
1463 static struct attribute *zpa2326_attributes[] = {
1464 &iio_const_attr_sampling_frequency_available.dev_attr.attr,
1465 NULL
1466 };
1467
1468 static const struct attribute_group zpa2326_attribute_group = {
1469 .attrs = zpa2326_attributes,
1470 };
1471
zpa2326_read_raw(struct iio_dev * indio_dev,struct iio_chan_spec const * chan,int * val,int * val2,long mask)1472 static int zpa2326_read_raw(struct iio_dev *indio_dev,
1473 struct iio_chan_spec const *chan,
1474 int *val,
1475 int *val2,
1476 long mask)
1477 {
1478 switch (mask) {
1479 case IIO_CHAN_INFO_RAW:
1480 return zpa2326_sample_oneshot(indio_dev, chan->type, val);
1481
1482 case IIO_CHAN_INFO_SCALE:
1483 switch (chan->type) {
1484 case IIO_PRESSURE:
1485 /*
1486 * Pressure resolution is 1/64 Pascal. Scale to kPascal
1487 * as required by IIO ABI.
1488 */
1489 *val = 1;
1490 *val2 = 64000;
1491 return IIO_VAL_FRACTIONAL;
1492
1493 case IIO_TEMP:
1494 /*
1495 * Temperature follows the equation:
1496 * Temp[degC] = Tempcode * 0.00649 - 176.83
1497 * where:
1498 * Tempcode is composed the raw sampled 16 bits.
1499 *
1500 * Hence, to produce a temperature in milli-degrees
1501 * Celsius according to IIO ABI, we need to apply the
1502 * following equation to raw samples:
1503 * Temp[milli degC] = (Tempcode + Offset) * Scale
1504 * where:
1505 * Offset = -176.83 / 0.00649
1506 * Scale = 0.00649 * 1000
1507 */
1508 *val = 6;
1509 *val2 = 490000;
1510 return IIO_VAL_INT_PLUS_MICRO;
1511
1512 default:
1513 return -EINVAL;
1514 }
1515
1516 case IIO_CHAN_INFO_OFFSET:
1517 switch (chan->type) {
1518 case IIO_TEMP:
1519 *val = -17683000;
1520 *val2 = 649;
1521 return IIO_VAL_FRACTIONAL;
1522
1523 default:
1524 return -EINVAL;
1525 }
1526
1527 case IIO_CHAN_INFO_SAMP_FREQ:
1528 *val = zpa2326_get_frequency(indio_dev);
1529 return IIO_VAL_INT;
1530
1531 default:
1532 return -EINVAL;
1533 }
1534 }
1535
zpa2326_write_raw(struct iio_dev * indio_dev,const struct iio_chan_spec * chan,int val,int val2,long mask)1536 static int zpa2326_write_raw(struct iio_dev *indio_dev,
1537 const struct iio_chan_spec *chan,
1538 int val,
1539 int val2,
1540 long mask)
1541 {
1542 if ((mask != IIO_CHAN_INFO_SAMP_FREQ) || val2)
1543 return -EINVAL;
1544
1545 return zpa2326_set_frequency(indio_dev, val);
1546 }
1547
1548 static const struct iio_chan_spec zpa2326_channels[] = {
1549 [0] = {
1550 .type = IIO_PRESSURE,
1551 .scan_index = 0,
1552 .scan_type = {
1553 .sign = 'u',
1554 .realbits = 24,
1555 .storagebits = 32,
1556 .endianness = IIO_LE,
1557 },
1558 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
1559 BIT(IIO_CHAN_INFO_SCALE),
1560 .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
1561 },
1562 [1] = {
1563 .type = IIO_TEMP,
1564 .scan_index = 1,
1565 .scan_type = {
1566 .sign = 's',
1567 .realbits = 16,
1568 .storagebits = 16,
1569 .endianness = IIO_LE,
1570 },
1571 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
1572 BIT(IIO_CHAN_INFO_SCALE) |
1573 BIT(IIO_CHAN_INFO_OFFSET),
1574 .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
1575 },
1576 [2] = IIO_CHAN_SOFT_TIMESTAMP(2),
1577 };
1578
1579 static const struct iio_info zpa2326_info = {
1580 .attrs = &zpa2326_attribute_group,
1581 .read_raw = zpa2326_read_raw,
1582 .write_raw = zpa2326_write_raw,
1583 };
1584
zpa2326_create_managed_iiodev(struct device * device,const char * name,struct regmap * regmap)1585 static struct iio_dev *zpa2326_create_managed_iiodev(struct device *device,
1586 const char *name,
1587 struct regmap *regmap)
1588 {
1589 struct iio_dev *indio_dev;
1590
1591 /* Allocate space to hold IIO device internal state. */
1592 indio_dev = devm_iio_device_alloc(device,
1593 sizeof(struct zpa2326_private));
1594 if (!indio_dev)
1595 return NULL;
1596
1597 /* Setup for userspace synchronous on demand sampling. */
1598 indio_dev->modes = INDIO_DIRECT_MODE;
1599 indio_dev->channels = zpa2326_channels;
1600 indio_dev->num_channels = ARRAY_SIZE(zpa2326_channels);
1601 indio_dev->name = name;
1602 indio_dev->info = &zpa2326_info;
1603
1604 return indio_dev;
1605 }
1606
zpa2326_probe(struct device * parent,const char * name,int irq,unsigned int hwid,struct regmap * regmap)1607 int zpa2326_probe(struct device *parent,
1608 const char *name,
1609 int irq,
1610 unsigned int hwid,
1611 struct regmap *regmap)
1612 {
1613 struct iio_dev *indio_dev;
1614 struct zpa2326_private *priv;
1615 int err;
1616 unsigned int id;
1617
1618 indio_dev = zpa2326_create_managed_iiodev(parent, name, regmap);
1619 if (!indio_dev)
1620 return -ENOMEM;
1621
1622 priv = iio_priv(indio_dev);
1623
1624 priv->vref = devm_regulator_get(parent, "vref");
1625 if (IS_ERR(priv->vref))
1626 return PTR_ERR(priv->vref);
1627
1628 priv->vdd = devm_regulator_get(parent, "vdd");
1629 if (IS_ERR(priv->vdd))
1630 return PTR_ERR(priv->vdd);
1631
1632 /* Set default hardware sampling frequency to highest rate supported. */
1633 priv->frequency = zpa2326_highest_frequency();
1634
1635 /*
1636 * Plug device's underlying bus abstraction : this MUST be set before
1637 * registering interrupt handlers since an interrupt might happen if
1638 * power up sequence is not properly applied.
1639 */
1640 priv->regmap = regmap;
1641
1642 err = devm_iio_triggered_buffer_setup(parent, indio_dev, NULL,
1643 zpa2326_trigger_handler,
1644 &zpa2326_buffer_setup_ops);
1645 if (err)
1646 return err;
1647
1648 err = zpa2326_init_managed_trigger(parent, indio_dev, priv, irq);
1649 if (err)
1650 return err;
1651
1652 err = zpa2326_init_managed_irq(parent, indio_dev, priv, irq);
1653 if (err)
1654 return err;
1655
1656 /* Power up to check device ID and perform initial hardware setup. */
1657 err = zpa2326_power_on(indio_dev, priv);
1658 if (err)
1659 return err;
1660
1661 /* Read id register to check we are talking to the right slave. */
1662 err = regmap_read(regmap, ZPA2326_DEVICE_ID_REG, &id);
1663 if (err)
1664 goto sleep;
1665
1666 if (id != hwid) {
1667 dev_err(parent, "found device with unexpected id %02x", id);
1668 err = -ENODEV;
1669 goto sleep;
1670 }
1671
1672 err = zpa2326_config_oneshot(indio_dev, irq);
1673 if (err)
1674 goto sleep;
1675
1676 /* Setup done : go sleeping. Device will be awaken upon user request. */
1677 err = zpa2326_sleep(indio_dev);
1678 if (err)
1679 goto poweroff;
1680
1681 dev_set_drvdata(parent, indio_dev);
1682
1683 zpa2326_init_runtime(parent);
1684
1685 err = iio_device_register(indio_dev);
1686 if (err) {
1687 zpa2326_fini_runtime(parent);
1688 goto poweroff;
1689 }
1690
1691 return 0;
1692
1693 sleep:
1694 /* Put to sleep just in case power regulators are "dummy" ones. */
1695 zpa2326_sleep(indio_dev);
1696 poweroff:
1697 zpa2326_power_off(indio_dev, priv);
1698
1699 return err;
1700 }
1701 EXPORT_SYMBOL_GPL(zpa2326_probe);
1702
zpa2326_remove(const struct device * parent)1703 void zpa2326_remove(const struct device *parent)
1704 {
1705 struct iio_dev *indio_dev = dev_get_drvdata(parent);
1706
1707 iio_device_unregister(indio_dev);
1708 zpa2326_fini_runtime(indio_dev->dev.parent);
1709 zpa2326_sleep(indio_dev);
1710 zpa2326_power_off(indio_dev, iio_priv(indio_dev));
1711 }
1712 EXPORT_SYMBOL_GPL(zpa2326_remove);
1713
1714 MODULE_AUTHOR("Gregor Boirie <gregor.boirie@parrot.com>");
1715 MODULE_DESCRIPTION("Core driver for Murata ZPA2326 pressure sensor");
1716 MODULE_LICENSE("GPL v2");
1717