Searched refs:SAR (Results 1 – 12 of 12) sorted by relevance
| /drivers/platform/x86/intel/int1092/ |
| D | Kconfig | 7 M.2 modem to regulate the RF power based on SAR data obtained from the
9 to SAR driver. The front end application in userspace will interact with SAR
11 SAR table index and use available communication like MBIM interface to enable
13 given platform needs to support "Dynamic SAR" configuration for a modem available
|
| /drivers/dma/ |
| D | txx9dmac.h | 72 u64 SAR; /* Source Address Register */ member
82 u32 SAR; member
206 u64 SAR; member
212 u32 SAR; member
|
| D | txx9dmac.c | 290 channel64_readq(dc, SAR), in txx9dmac_dump_regs()
302 channel32_readl(dc, SAR), in txx9dmac_dump_regs()
316 channel_writeq(dc, SAR, 0); in txx9dmac_reset_chan()
320 channel_writel(dc, SAR, 0); in txx9dmac_reset_chan()
474 (u64)desc->CHAR, desc->SAR, desc->DAR, desc->CNTR); in txx9dmac_dump_desc()
479 (u64)desc->CHAR, desc->SAR, desc->DAR, desc->CNTR, in txx9dmac_dump_desc()
487 d->CHAR, d->SAR, d->DAR, d->CNTR); in txx9dmac_dump_desc()
492 d->CHAR, d->SAR, d->DAR, d->CNTR, in txx9dmac_dump_desc()
755 desc->hwdesc.SAR = src + offset; in txx9dmac_prep_dma_memcpy()
761 desc->hwdesc32.SAR = src + offset; in txx9dmac_prep_dma_memcpy()
[all …]
|
| D | idma64.c | 94 channel_writeq(idma64c, SAR, 0); in idma64_chan_start()
|
| D | pl330.c | 339 SAR = 0, enumerator
732 dst == SAR ? "SAR" : (dst == DAR ? "DAR" : "CCR"), val); in _emit_MOV()
1400 off += _emit_MOV(dry_run, &buf[off], SAR, x->src_addr); in _setup_xfer()
|
| /drivers/i2c/busses/ |
| D | i2c-rcar.c | 70 #define SAR (1 << 0) /* slave addr received */ macro
578 if (ssr_filtered & SAR) { in rcar_i2c_slave_irq()
583 rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR); in rcar_i2c_slave_irq()
587 rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR); in rcar_i2c_slave_irq()
591 rcar_i2c_write(priv, ICSSR, ~(SAR | SSR) & 0xff); in rcar_i2c_slave_irq()
598 rcar_i2c_write(priv, ICSIER, SAR); in rcar_i2c_slave_irq()
948 rcar_i2c_write(priv, ICSIER, SAR); in rcar_reg_slave()
|
| /drivers/net/wireless/ath/ath9k/ |
| D | Kconfig | 88 TX99 support enables Specific Absorption Rate (SAR) testing.
89 SAR is the unit of measurement for the amount of radio frequency(RF)
91 limits used are expressed in the terms of SAR, which is a measure
96 governmental SAR regulations.
|
| /drivers/dma/sh/ |
| D | shdmac.c | 38 #define SAR 0x00 /* Source Address Register */ macro
217 sh_dmae_writel(sh_chan, hw->sar, SAR); in dmae_set_reg()
460 u32 sar_buf = sh_dmae_readl(sh_chan, SAR); in sh_dmae_desc_completed()
|
| /drivers/dma/dw/ |
| D | regs.h | 40 DW_REG(SAR); /* Source Address Register */
|
| D | core.c | 134 channel_readl(dwc, SAR), in dwc_dump_chan_regs()
163 channel_writel(dwc, SAR, lli_read(desc, sar)); in dwc_do_single_block()
|
| /drivers/iio/adc/ |
| D | Kconfig | 743 tristate "Amlogic Meson SAR ADC driver"
748 Say yes here to build support for the SAR ADC found in Amlogic Meson
|
| /drivers/mfd/ |
| D | Kconfig | 1976 10 bits SAR ADC for battery temperature monitor and 1S battery
|