1123 	mr = BIT_3 | BIT_2 | BIT_1 | BIT_0;  in qla1280_set_target_parameters()
1689 		err = qla1280_mailbox_command(ha, BIT_0 | BIT_1 | BIT_2, mb);  in qla1280_load_firmware_pio()
1703 #define CMD_ARGS	(BIT_7 | BIT_6 | BIT_4 | BIT_3 | BIT_2 | BIT_1 | BIT_0)
1707 #define CMD_ARGS	(BIT_4 | BIT_3 | BIT_2 | BIT_1 | BIT_0)
1831 	err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_start_firmware()
1841 	err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_start_firmware()
1908 					       BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_init_rings()
1922 						 BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_init_rings()
2142 	status = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_config_bus()
2215 			     BIT_7 | BIT_3 | BIT_2 | BIT_1 | BIT_0);  in qla1280_nvram_config()
2227 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2233 	 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2241 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2250 					  BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2256 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2270 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2274 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2278 	mb[1] = BIT_1;	/* Data DMA Channel Burst Enable */  in qla1280_nvram_config()
2279 	mb[2] = BIT_1;	/* Command DMA Channel Burst Enable */  in qla1280_nvram_config()
2280 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2284 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2290 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2562 	status = qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_bus_reset()
2616 	status = qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_device_reset()
3705 	else if (pkt->entry_status & BIT_1)  in qla1280_error_entry()
3725 		} else if (pkt->entry_status & BIT_1) {	/* FULL flag */  in qla1280_error_entry()
3902 	qla1280_mailbox_command(ha, BIT_6 | BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_get_target_parameters()