572 		xhci_dbg(xhci, "Ignoring request to disable "  in xhci_disable_port()
578 		xhci_dbg(xhci,  in xhci_disable_port()
586 	xhci_dbg(xhci, "disable port %d-%d, portsc: 0x%x\n",  in xhci_disable_port()
637 	xhci_dbg(xhci, "clear port%d %s change, portsc: 0x%x\n",  in xhci_clear_port_change_bit()
667 	xhci_dbg(xhci, "set port power %d-%d %s, portsc: 0x%x\n",  in xhci_set_port_power()
713 	xhci_dbg(xhci, "Disable all slots\n");  in xhci_enter_test_mode()
727 	xhci_dbg(xhci, "Disable all port (PP = 0)\n");  in xhci_enter_test_mode()
735 	xhci_dbg(xhci, "Stop controller\n");  in xhci_enter_test_mode()
743 	xhci_dbg(xhci, "Enter Test Mode: %d, Port_id=%d\n",  in xhci_enter_test_mode()
780 	xhci_dbg(xhci, "Set port %d-%d link state, portsc: 0x%x, write 0x%x",  in xhci_set_link_state()
952 		xhci_dbg(xhci, "resume USB2 port %d-%d\n",  in xhci_handle_usb2_port_link_resume()
973 				xhci_dbg(xhci, "slot_id is zero\n");  in xhci_handle_usb2_port_link_resume()
1217 			xhci_dbg(xhci, "Wrong hub descriptor type for "  in xhci_hub_control()
1250 		xhci_dbg(xhci, "Get port status %d-%d read: 0x%x, return 0x%x",  in xhci_hub_control()
1336 				xhci_dbg(xhci, "Disable port %d-%d\n",  in xhci_hub_control()
1353 				xhci_dbg(xhci, "Enable port %d-%d\n",  in xhci_hub_control()
1377 					xhci_dbg(xhci, "CTC flag is 0, port already supports entering compliance mode\n");  in xhci_hub_control()
1386 				xhci_dbg(xhci, "Enable compliance mode transition for port %d-%d\n",  in xhci_hub_control()
1438 					xhci_dbg(xhci, "missing U0 port change event for port %d-%d\n",  in xhci_hub_control()
1484 			xhci_dbg(xhci, "set port reset, actual port %d-%d status  = 0x%x\n",  in xhci_hub_control()
1491 			xhci_dbg(xhci, "set port remote wake mask, actual port %d-%d status  = 0x%x\n",  in xhci_hub_control()
1546 			xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");  in xhci_hub_control()
1547 			xhci_dbg(xhci, "PORTSC %04x\n", temp);  in xhci_hub_control()
1571 				xhci_dbg(xhci, "slot_id is zero\n");  in xhci_hub_control()
1686 		xhci_dbg(xhci, "%s: stopping usb%d port polling\n",  in xhci_hub_status_data()
1719 			xhci_dbg(xhci, "usb%d bus suspend to fail because a port is resuming\n",  in xhci_bus_suspend()
1747 			xhci_dbg(xhci, "port %d-%d polling in bus suspend, waiting\n",  in xhci_bus_suspend()
1755 			xhci_dbg(xhci, "Bus suspend bailout, port over-current detected\n");  in xhci_bus_suspend()
1763 				xhci_dbg(xhci, "Bus suspend bailout, port connect change\n");  in xhci_bus_suspend()
1766 			xhci_dbg(xhci, "port %d-%d not suspended\n",  in xhci_bus_suspend()
1901 			xhci_dbg(xhci, "reset stuck port %d-%d\n",  in xhci_bus_resume()