1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * pmbus.h - Common defines and structures for PMBus devices 4 * 5 * Copyright (c) 2010, 2011 Ericsson AB. 6 * Copyright (c) 2012 Guenter Roeck 7 */ 8 9 #ifndef PMBUS_H 10 #define PMBUS_H 11 12 #include <linux/bitops.h> 13 #include <linux/regulator/driver.h> 14 15 /* 16 * Registers 17 */ 18 enum pmbus_regs { 19 PMBUS_PAGE = 0x00, 20 PMBUS_OPERATION = 0x01, 21 PMBUS_ON_OFF_CONFIG = 0x02, 22 PMBUS_CLEAR_FAULTS = 0x03, 23 PMBUS_PHASE = 0x04, 24 25 PMBUS_WRITE_PROTECT = 0x10, 26 27 PMBUS_CAPABILITY = 0x19, 28 PMBUS_QUERY = 0x1A, 29 30 PMBUS_VOUT_MODE = 0x20, 31 PMBUS_VOUT_COMMAND = 0x21, 32 PMBUS_VOUT_TRIM = 0x22, 33 PMBUS_VOUT_CAL_OFFSET = 0x23, 34 PMBUS_VOUT_MAX = 0x24, 35 PMBUS_VOUT_MARGIN_HIGH = 0x25, 36 PMBUS_VOUT_MARGIN_LOW = 0x26, 37 PMBUS_VOUT_TRANSITION_RATE = 0x27, 38 PMBUS_VOUT_DROOP = 0x28, 39 PMBUS_VOUT_SCALE_LOOP = 0x29, 40 PMBUS_VOUT_SCALE_MONITOR = 0x2A, 41 42 PMBUS_COEFFICIENTS = 0x30, 43 PMBUS_POUT_MAX = 0x31, 44 45 PMBUS_FAN_CONFIG_12 = 0x3A, 46 PMBUS_FAN_COMMAND_1 = 0x3B, 47 PMBUS_FAN_COMMAND_2 = 0x3C, 48 PMBUS_FAN_CONFIG_34 = 0x3D, 49 PMBUS_FAN_COMMAND_3 = 0x3E, 50 PMBUS_FAN_COMMAND_4 = 0x3F, 51 52 PMBUS_VOUT_OV_FAULT_LIMIT = 0x40, 53 PMBUS_VOUT_OV_FAULT_RESPONSE = 0x41, 54 PMBUS_VOUT_OV_WARN_LIMIT = 0x42, 55 PMBUS_VOUT_UV_WARN_LIMIT = 0x43, 56 PMBUS_VOUT_UV_FAULT_LIMIT = 0x44, 57 PMBUS_VOUT_UV_FAULT_RESPONSE = 0x45, 58 PMBUS_IOUT_OC_FAULT_LIMIT = 0x46, 59 PMBUS_IOUT_OC_FAULT_RESPONSE = 0x47, 60 PMBUS_IOUT_OC_LV_FAULT_LIMIT = 0x48, 61 PMBUS_IOUT_OC_LV_FAULT_RESPONSE = 0x49, 62 PMBUS_IOUT_OC_WARN_LIMIT = 0x4A, 63 PMBUS_IOUT_UC_FAULT_LIMIT = 0x4B, 64 PMBUS_IOUT_UC_FAULT_RESPONSE = 0x4C, 65 66 PMBUS_OT_FAULT_LIMIT = 0x4F, 67 PMBUS_OT_FAULT_RESPONSE = 0x50, 68 PMBUS_OT_WARN_LIMIT = 0x51, 69 PMBUS_UT_WARN_LIMIT = 0x52, 70 PMBUS_UT_FAULT_LIMIT = 0x53, 71 PMBUS_UT_FAULT_RESPONSE = 0x54, 72 PMBUS_VIN_OV_FAULT_LIMIT = 0x55, 73 PMBUS_VIN_OV_FAULT_RESPONSE = 0x56, 74 PMBUS_VIN_OV_WARN_LIMIT = 0x57, 75 PMBUS_VIN_UV_WARN_LIMIT = 0x58, 76 PMBUS_VIN_UV_FAULT_LIMIT = 0x59, 77 78 PMBUS_IIN_OC_FAULT_LIMIT = 0x5B, 79 PMBUS_IIN_OC_WARN_LIMIT = 0x5D, 80 81 PMBUS_POUT_OP_FAULT_LIMIT = 0x68, 82 PMBUS_POUT_OP_WARN_LIMIT = 0x6A, 83 PMBUS_PIN_OP_WARN_LIMIT = 0x6B, 84 85 PMBUS_STATUS_BYTE = 0x78, 86 PMBUS_STATUS_WORD = 0x79, 87 PMBUS_STATUS_VOUT = 0x7A, 88 PMBUS_STATUS_IOUT = 0x7B, 89 PMBUS_STATUS_INPUT = 0x7C, 90 PMBUS_STATUS_TEMPERATURE = 0x7D, 91 PMBUS_STATUS_CML = 0x7E, 92 PMBUS_STATUS_OTHER = 0x7F, 93 PMBUS_STATUS_MFR_SPECIFIC = 0x80, 94 PMBUS_STATUS_FAN_12 = 0x81, 95 PMBUS_STATUS_FAN_34 = 0x82, 96 97 PMBUS_READ_VIN = 0x88, 98 PMBUS_READ_IIN = 0x89, 99 PMBUS_READ_VCAP = 0x8A, 100 PMBUS_READ_VOUT = 0x8B, 101 PMBUS_READ_IOUT = 0x8C, 102 PMBUS_READ_TEMPERATURE_1 = 0x8D, 103 PMBUS_READ_TEMPERATURE_2 = 0x8E, 104 PMBUS_READ_TEMPERATURE_3 = 0x8F, 105 PMBUS_READ_FAN_SPEED_1 = 0x90, 106 PMBUS_READ_FAN_SPEED_2 = 0x91, 107 PMBUS_READ_FAN_SPEED_3 = 0x92, 108 PMBUS_READ_FAN_SPEED_4 = 0x93, 109 PMBUS_READ_DUTY_CYCLE = 0x94, 110 PMBUS_READ_FREQUENCY = 0x95, 111 PMBUS_READ_POUT = 0x96, 112 PMBUS_READ_PIN = 0x97, 113 114 PMBUS_REVISION = 0x98, 115 PMBUS_MFR_ID = 0x99, 116 PMBUS_MFR_MODEL = 0x9A, 117 PMBUS_MFR_REVISION = 0x9B, 118 PMBUS_MFR_LOCATION = 0x9C, 119 PMBUS_MFR_DATE = 0x9D, 120 PMBUS_MFR_SERIAL = 0x9E, 121 122 PMBUS_MFR_VIN_MIN = 0xA0, 123 PMBUS_MFR_VIN_MAX = 0xA1, 124 PMBUS_MFR_IIN_MAX = 0xA2, 125 PMBUS_MFR_PIN_MAX = 0xA3, 126 PMBUS_MFR_VOUT_MIN = 0xA4, 127 PMBUS_MFR_VOUT_MAX = 0xA5, 128 PMBUS_MFR_IOUT_MAX = 0xA6, 129 PMBUS_MFR_POUT_MAX = 0xA7, 130 131 PMBUS_IC_DEVICE_ID = 0xAD, 132 PMBUS_IC_DEVICE_REV = 0xAE, 133 134 PMBUS_MFR_MAX_TEMP_1 = 0xC0, 135 PMBUS_MFR_MAX_TEMP_2 = 0xC1, 136 PMBUS_MFR_MAX_TEMP_3 = 0xC2, 137 138 /* 139 * Virtual registers. 140 * Useful to support attributes which are not supported by standard PMBus 141 * registers but exist as manufacturer specific registers on individual chips. 142 * Must be mapped to real registers in device specific code. 143 * 144 * Semantics: 145 * Virtual registers are all word size. 146 * READ registers are read-only; writes are either ignored or return an error. 147 * RESET registers are read/write. Reading reset registers returns zero 148 * (used for detection), writing any value causes the associated history to be 149 * reset. 150 * Virtual registers have to be handled in device specific driver code. Chip 151 * driver code returns non-negative register values if a virtual register is 152 * supported, or a negative error code if not. The chip driver may return 153 * -ENODATA or any other error code in this case, though an error code other 154 * than -ENODATA is handled more efficiently and thus preferred. Either case, 155 * the calling PMBus core code will abort if the chip driver returns an error 156 * code when reading or writing virtual registers. 157 */ 158 PMBUS_VIRT_BASE = 0x100, 159 PMBUS_VIRT_READ_TEMP_AVG, 160 PMBUS_VIRT_READ_TEMP_MIN, 161 PMBUS_VIRT_READ_TEMP_MAX, 162 PMBUS_VIRT_RESET_TEMP_HISTORY, 163 PMBUS_VIRT_READ_VIN_AVG, 164 PMBUS_VIRT_READ_VIN_MIN, 165 PMBUS_VIRT_READ_VIN_MAX, 166 PMBUS_VIRT_RESET_VIN_HISTORY, 167 PMBUS_VIRT_READ_IIN_AVG, 168 PMBUS_VIRT_READ_IIN_MIN, 169 PMBUS_VIRT_READ_IIN_MAX, 170 PMBUS_VIRT_RESET_IIN_HISTORY, 171 PMBUS_VIRT_READ_PIN_AVG, 172 PMBUS_VIRT_READ_PIN_MIN, 173 PMBUS_VIRT_READ_PIN_MAX, 174 PMBUS_VIRT_RESET_PIN_HISTORY, 175 PMBUS_VIRT_READ_POUT_AVG, 176 PMBUS_VIRT_READ_POUT_MIN, 177 PMBUS_VIRT_READ_POUT_MAX, 178 PMBUS_VIRT_RESET_POUT_HISTORY, 179 PMBUS_VIRT_READ_VOUT_AVG, 180 PMBUS_VIRT_READ_VOUT_MIN, 181 PMBUS_VIRT_READ_VOUT_MAX, 182 PMBUS_VIRT_RESET_VOUT_HISTORY, 183 PMBUS_VIRT_READ_IOUT_AVG, 184 PMBUS_VIRT_READ_IOUT_MIN, 185 PMBUS_VIRT_READ_IOUT_MAX, 186 PMBUS_VIRT_RESET_IOUT_HISTORY, 187 PMBUS_VIRT_READ_TEMP2_AVG, 188 PMBUS_VIRT_READ_TEMP2_MIN, 189 PMBUS_VIRT_READ_TEMP2_MAX, 190 PMBUS_VIRT_RESET_TEMP2_HISTORY, 191 192 PMBUS_VIRT_READ_VMON, 193 PMBUS_VIRT_VMON_UV_WARN_LIMIT, 194 PMBUS_VIRT_VMON_OV_WARN_LIMIT, 195 PMBUS_VIRT_VMON_UV_FAULT_LIMIT, 196 PMBUS_VIRT_VMON_OV_FAULT_LIMIT, 197 PMBUS_VIRT_STATUS_VMON, 198 199 /* 200 * RPM and PWM Fan control 201 * 202 * Drivers wanting to expose PWM control must define the behaviour of 203 * PMBUS_VIRT_PWM_[1-4] and PMBUS_VIRT_PWM_ENABLE_[1-4] in the 204 * {read,write}_word_data callback. 205 * 206 * pmbus core provides a default implementation for 207 * PMBUS_VIRT_FAN_TARGET_[1-4]. 208 * 209 * TARGET, PWM and PWM_ENABLE members must be defined sequentially; 210 * pmbus core uses the difference between the provided register and 211 * it's _1 counterpart to calculate the FAN/PWM ID. 212 */ 213 PMBUS_VIRT_FAN_TARGET_1, 214 PMBUS_VIRT_FAN_TARGET_2, 215 PMBUS_VIRT_FAN_TARGET_3, 216 PMBUS_VIRT_FAN_TARGET_4, 217 PMBUS_VIRT_PWM_1, 218 PMBUS_VIRT_PWM_2, 219 PMBUS_VIRT_PWM_3, 220 PMBUS_VIRT_PWM_4, 221 PMBUS_VIRT_PWM_ENABLE_1, 222 PMBUS_VIRT_PWM_ENABLE_2, 223 PMBUS_VIRT_PWM_ENABLE_3, 224 PMBUS_VIRT_PWM_ENABLE_4, 225 226 /* Samples for average 227 * 228 * Drivers wanting to expose functionality for changing the number of 229 * samples used for average values should implement support in 230 * {read,write}_word_data callback for either PMBUS_VIRT_SAMPLES if it 231 * applies to all types of measurements, or any number of specific 232 * PMBUS_VIRT_*_SAMPLES registers to allow for individual control. 233 */ 234 PMBUS_VIRT_SAMPLES, 235 PMBUS_VIRT_IN_SAMPLES, 236 PMBUS_VIRT_CURR_SAMPLES, 237 PMBUS_VIRT_POWER_SAMPLES, 238 PMBUS_VIRT_TEMP_SAMPLES, 239 }; 240 241 /* 242 * OPERATION 243 */ 244 #define PB_OPERATION_CONTROL_ON BIT(7) 245 246 /* 247 * WRITE_PROTECT 248 */ 249 #define PB_WP_ALL BIT(7) /* all but WRITE_PROTECT */ 250 #define PB_WP_OP BIT(6) /* all but WP, OPERATION, PAGE */ 251 #define PB_WP_VOUT BIT(5) /* all but WP, OPERATION, PAGE, VOUT, ON_OFF */ 252 253 #define PB_WP_ANY (PB_WP_ALL | PB_WP_OP | PB_WP_VOUT) 254 255 /* 256 * CAPABILITY 257 */ 258 #define PB_CAPABILITY_SMBALERT BIT(4) 259 #define PB_CAPABILITY_ERROR_CHECK BIT(7) 260 261 /* 262 * VOUT_MODE 263 */ 264 #define PB_VOUT_MODE_MODE_MASK 0xe0 265 #define PB_VOUT_MODE_PARAM_MASK 0x1f 266 267 #define PB_VOUT_MODE_LINEAR 0x00 268 #define PB_VOUT_MODE_VID 0x20 269 #define PB_VOUT_MODE_DIRECT 0x40 270 271 /* 272 * Fan configuration 273 */ 274 #define PB_FAN_2_PULSE_MASK (BIT(0) | BIT(1)) 275 #define PB_FAN_2_RPM BIT(2) 276 #define PB_FAN_2_INSTALLED BIT(3) 277 #define PB_FAN_1_PULSE_MASK (BIT(4) | BIT(5)) 278 #define PB_FAN_1_RPM BIT(6) 279 #define PB_FAN_1_INSTALLED BIT(7) 280 281 enum pmbus_fan_mode { percent = 0, rpm }; 282 283 /* 284 * STATUS_BYTE, STATUS_WORD (lower) 285 */ 286 #define PB_STATUS_NONE_ABOVE BIT(0) 287 #define PB_STATUS_CML BIT(1) 288 #define PB_STATUS_TEMPERATURE BIT(2) 289 #define PB_STATUS_VIN_UV BIT(3) 290 #define PB_STATUS_IOUT_OC BIT(4) 291 #define PB_STATUS_VOUT_OV BIT(5) 292 #define PB_STATUS_OFF BIT(6) 293 #define PB_STATUS_BUSY BIT(7) 294 295 /* 296 * STATUS_WORD (upper) 297 */ 298 #define PB_STATUS_UNKNOWN BIT(8) 299 #define PB_STATUS_OTHER BIT(9) 300 #define PB_STATUS_FANS BIT(10) 301 #define PB_STATUS_POWER_GOOD_N BIT(11) 302 #define PB_STATUS_WORD_MFR BIT(12) 303 #define PB_STATUS_INPUT BIT(13) 304 #define PB_STATUS_IOUT_POUT BIT(14) 305 #define PB_STATUS_VOUT BIT(15) 306 307 /* 308 * STATUS_IOUT 309 */ 310 #define PB_POUT_OP_WARNING BIT(0) 311 #define PB_POUT_OP_FAULT BIT(1) 312 #define PB_POWER_LIMITING BIT(2) 313 #define PB_CURRENT_SHARE_FAULT BIT(3) 314 #define PB_IOUT_UC_FAULT BIT(4) 315 #define PB_IOUT_OC_WARNING BIT(5) 316 #define PB_IOUT_OC_LV_FAULT BIT(6) 317 #define PB_IOUT_OC_FAULT BIT(7) 318 319 /* 320 * STATUS_VOUT, STATUS_INPUT 321 */ 322 #define PB_VOLTAGE_VIN_OFF BIT(3) 323 #define PB_VOLTAGE_UV_FAULT BIT(4) 324 #define PB_VOLTAGE_UV_WARNING BIT(5) 325 #define PB_VOLTAGE_OV_WARNING BIT(6) 326 #define PB_VOLTAGE_OV_FAULT BIT(7) 327 328 /* 329 * STATUS_INPUT 330 */ 331 #define PB_PIN_OP_WARNING BIT(0) 332 #define PB_IIN_OC_WARNING BIT(1) 333 #define PB_IIN_OC_FAULT BIT(2) 334 335 /* 336 * STATUS_TEMPERATURE 337 */ 338 #define PB_TEMP_UT_FAULT BIT(4) 339 #define PB_TEMP_UT_WARNING BIT(5) 340 #define PB_TEMP_OT_WARNING BIT(6) 341 #define PB_TEMP_OT_FAULT BIT(7) 342 343 /* 344 * STATUS_FAN 345 */ 346 #define PB_FAN_AIRFLOW_WARNING BIT(0) 347 #define PB_FAN_AIRFLOW_FAULT BIT(1) 348 #define PB_FAN_FAN2_SPEED_OVERRIDE BIT(2) 349 #define PB_FAN_FAN1_SPEED_OVERRIDE BIT(3) 350 #define PB_FAN_FAN2_WARNING BIT(4) 351 #define PB_FAN_FAN1_WARNING BIT(5) 352 #define PB_FAN_FAN2_FAULT BIT(6) 353 #define PB_FAN_FAN1_FAULT BIT(7) 354 355 /* 356 * CML_FAULT_STATUS 357 */ 358 #define PB_CML_FAULT_OTHER_MEM_LOGIC BIT(0) 359 #define PB_CML_FAULT_OTHER_COMM BIT(1) 360 #define PB_CML_FAULT_PROCESSOR BIT(3) 361 #define PB_CML_FAULT_MEMORY BIT(4) 362 #define PB_CML_FAULT_PACKET_ERROR BIT(5) 363 #define PB_CML_FAULT_INVALID_DATA BIT(6) 364 #define PB_CML_FAULT_INVALID_COMMAND BIT(7) 365 366 enum pmbus_sensor_classes { 367 PSC_VOLTAGE_IN = 0, 368 PSC_VOLTAGE_OUT, 369 PSC_CURRENT_IN, 370 PSC_CURRENT_OUT, 371 PSC_POWER, 372 PSC_TEMPERATURE, 373 PSC_FAN, 374 PSC_PWM, 375 PSC_NUM_CLASSES /* Number of power sensor classes */ 376 }; 377 378 #define PMBUS_PAGES 32 /* Per PMBus specification */ 379 #define PMBUS_PHASES 10 /* Maximum number of phases per page */ 380 381 /* Functionality bit mask */ 382 #define PMBUS_HAVE_VIN BIT(0) 383 #define PMBUS_HAVE_VCAP BIT(1) 384 #define PMBUS_HAVE_VOUT BIT(2) 385 #define PMBUS_HAVE_IIN BIT(3) 386 #define PMBUS_HAVE_IOUT BIT(4) 387 #define PMBUS_HAVE_PIN BIT(5) 388 #define PMBUS_HAVE_POUT BIT(6) 389 #define PMBUS_HAVE_FAN12 BIT(7) 390 #define PMBUS_HAVE_FAN34 BIT(8) 391 #define PMBUS_HAVE_TEMP BIT(9) 392 #define PMBUS_HAVE_TEMP2 BIT(10) 393 #define PMBUS_HAVE_TEMP3 BIT(11) 394 #define PMBUS_HAVE_STATUS_VOUT BIT(12) 395 #define PMBUS_HAVE_STATUS_IOUT BIT(13) 396 #define PMBUS_HAVE_STATUS_INPUT BIT(14) 397 #define PMBUS_HAVE_STATUS_TEMP BIT(15) 398 #define PMBUS_HAVE_STATUS_FAN12 BIT(16) 399 #define PMBUS_HAVE_STATUS_FAN34 BIT(17) 400 #define PMBUS_HAVE_VMON BIT(18) 401 #define PMBUS_HAVE_STATUS_VMON BIT(19) 402 #define PMBUS_HAVE_PWM12 BIT(20) 403 #define PMBUS_HAVE_PWM34 BIT(21) 404 #define PMBUS_HAVE_SAMPLES BIT(22) 405 406 #define PMBUS_PHASE_VIRTUAL BIT(30) /* Phases on this page are virtual */ 407 #define PMBUS_PAGE_VIRTUAL BIT(31) /* Page is virtual */ 408 409 enum pmbus_data_format { linear = 0, direct, vid }; 410 enum vrm_version { vr11 = 0, vr12, vr13, imvp9, amd625mv }; 411 412 struct pmbus_driver_info { 413 int pages; /* Total number of pages */ 414 u8 phases[PMBUS_PAGES]; /* Number of phases per page */ 415 enum pmbus_data_format format[PSC_NUM_CLASSES]; 416 enum vrm_version vrm_version[PMBUS_PAGES]; /* vrm version per page */ 417 /* 418 * Support one set of coefficients for each sensor type 419 * Used for chips providing data in direct mode. 420 */ 421 int m[PSC_NUM_CLASSES]; /* mantissa for direct data format */ 422 int b[PSC_NUM_CLASSES]; /* offset */ 423 int R[PSC_NUM_CLASSES]; /* exponent */ 424 425 u32 func[PMBUS_PAGES]; /* Functionality, per page */ 426 u32 pfunc[PMBUS_PHASES];/* Functionality, per phase */ 427 /* 428 * The following functions map manufacturing specific register values 429 * to PMBus standard register values. Specify only if mapping is 430 * necessary. 431 * Functions return the register value (read) or zero (write) if 432 * successful. A return value of -ENODATA indicates that there is no 433 * manufacturer specific register, but that a standard PMBus register 434 * may exist. Any other negative return value indicates that the 435 * register does not exist, and that no attempt should be made to read 436 * the standard register. 437 */ 438 int (*read_byte_data)(struct i2c_client *client, int page, int reg); 439 int (*read_word_data)(struct i2c_client *client, int page, int phase, 440 int reg); 441 int (*write_word_data)(struct i2c_client *client, int page, int reg, 442 u16 word); 443 int (*write_byte)(struct i2c_client *client, int page, u8 value); 444 /* 445 * The identify function determines supported PMBus functionality. 446 * This function is only necessary if a chip driver supports multiple 447 * chips, and the chip functionality is not pre-determined. 448 */ 449 int (*identify)(struct i2c_client *client, 450 struct pmbus_driver_info *info); 451 452 /* Regulator functionality, if supported by this chip driver. */ 453 int num_regulators; 454 const struct regulator_desc *reg_desc; 455 456 /* custom attributes */ 457 const struct attribute_group **groups; 458 }; 459 460 /* Regulator ops */ 461 462 extern const struct regulator_ops pmbus_regulator_ops; 463 464 /* Macro for filling in array of struct regulator_desc */ 465 #define PMBUS_REGULATOR(_name, _id) \ 466 [_id] = { \ 467 .name = (_name # _id), \ 468 .id = (_id), \ 469 .of_match = of_match_ptr(_name # _id), \ 470 .regulators_node = of_match_ptr("regulators"), \ 471 .ops = &pmbus_regulator_ops, \ 472 .type = REGULATOR_VOLTAGE, \ 473 .owner = THIS_MODULE, \ 474 } 475 476 /* Function declarations */ 477 478 void pmbus_clear_cache(struct i2c_client *client); 479 void pmbus_set_update(struct i2c_client *client, u8 reg, bool update); 480 int pmbus_set_page(struct i2c_client *client, int page, int phase); 481 int pmbus_read_word_data(struct i2c_client *client, int page, int phase, 482 u8 reg); 483 int pmbus_write_word_data(struct i2c_client *client, int page, u8 reg, 484 u16 word); 485 int pmbus_read_byte_data(struct i2c_client *client, int page, u8 reg); 486 int pmbus_write_byte(struct i2c_client *client, int page, u8 value); 487 int pmbus_write_byte_data(struct i2c_client *client, int page, u8 reg, 488 u8 value); 489 int pmbus_update_byte_data(struct i2c_client *client, int page, u8 reg, 490 u8 mask, u8 value); 491 void pmbus_clear_faults(struct i2c_client *client); 492 bool pmbus_check_byte_register(struct i2c_client *client, int page, int reg); 493 bool pmbus_check_word_register(struct i2c_client *client, int page, int reg); 494 int pmbus_do_probe(struct i2c_client *client, struct pmbus_driver_info *info); 495 const struct pmbus_driver_info *pmbus_get_driver_info(struct i2c_client 496 *client); 497 int pmbus_get_fan_rate_device(struct i2c_client *client, int page, int id, 498 enum pmbus_fan_mode mode); 499 int pmbus_get_fan_rate_cached(struct i2c_client *client, int page, int id, 500 enum pmbus_fan_mode mode); 501 int pmbus_update_fan(struct i2c_client *client, int page, int id, 502 u8 config, u8 mask, u16 command); 503 struct dentry *pmbus_get_debugfs_dir(struct i2c_client *client); 504 505 #endif /* PMBUS_H */ 506