Searched refs:must (Results 1 – 25 of 98) sorted by relevance
1234
| /drivers/media/dvb-frontends/drx39xyj/ |
| D | drx_dap_fasi.h | 98 #error At least one of short- or long-addressing format must be allowed.
201 #error DRXDAP_MAX_WCHUNKSIZE must be at least 3 in single master mode
204 #error DRXDAP_MAX_WCHUNKSIZE must be at least 5 in multi master mode
209 #error DRXDAP_MAX_WCHUNKSIZE must be at least 5 in single master mode
212 #error DRXDAP_MAX_WCHUNKSIZE must be at least 7 in multi master mode
225 #error DRXDAP_MAX_RCHUNKSIZE must be at least 2
231 #error DRXDAP_MAX_RCHUNKSIZE must be even
|
| /drivers/ntb/hw/idt/ |
| D | Kconfig | 9 Some of the pre-initializations must be made before IDT PCIe-switch
13 value. Evidently it must be done before PCI bus enumeration is
16 First of all partitions must be activated and properly assigned to all
18 and SWPORTxCTL registers). Then all NT-function BARs must be enabled
21 accepted by a BAR. Note that BAR0 must map PCI configuration space
|
| /drivers/block/paride/ |
| D | Kconfig | 6 # PARIDE must also be a module.
21 must also have at least one parallel port protocol driver in your
36 must also have at least one parallel port protocol driver in your
52 You must also have at least one parallel port protocol driver in
66 You must also have at least one parallel port protocol driver in
84 You must also have at least one parallel port protocol driver in
106 loadable module. The module will be called aten. You must also
125 called bpck. You must also have a high-level driver for the type
144 called bpck6. You must also have a high-level driver for the type
155 module. The module will be called comm. You must also have
[all …]
|
| /drivers/pci/controller/dwc/ |
| D | Kconfig | 34 host-specific features PCI_DRA7XX_HOST must be selected and in order
35 to enable device-specific features PCI_DRA7XX_EP must be selected.
49 host-specific features PCI_DRA7XX_HOST must be selected and in order
50 to enable device-specific features PCI_DRA7XX_EP must be selected.
66 host-specific features PCIE_DW_PLAT_HOST must be selected and in
67 order to enable device-specific features PCI_DW_PLAT_EP must be
81 host-specific features PCIE_DW_PLAT_HOST must be selected and in
82 order to enable device-specific features PCI_DW_PLAT_EP must be
309 enable host-specific features PCIE_TEGRA194_HOST must be selected and
310 in order to enable device-specific features PCIE_TEGRA194_EP must be
[all …]
|
| /drivers/mfd/ |
| D | Kconfig | 111 additional drivers must be enabled in order to use the
143 additional drivers must be enabled in order to use the
199 Note on x86 this provides an ACPI OpRegion, so this must be 'y'
200 (builtin) and not a module, as the OpRegion must be available as
202 I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_BAYTRAIL must be 'y' too.
325 for accessing the device, additional drivers must be enabled in
337 for accessing the device, additional drivers must be enabled in
350 Additional drivers must be enabled in order to use the functionality
366 Additional drivers must be enabled in order to use the functionality
378 Additional drivers must be enabled in order to use the functionality
[all …]
|
| /drivers/staging/mt7621-pci/ |
| D | mediatek,mt7621-pci.txt | 8 - #address-cells: Address representation for root ports (must be 3)
11 - #size-cells: Size representation for root ports (must be 2)
28 In addition, the device tree node must have sub-nodes describing each PCIe port
|
| /drivers/platform/x86/intel/int3472/ |
| D | Kconfig | 22 an ACPI OpRegion, which must be available before any of the devices
25 I2C_DESIGNWARE_PLATFORM option must be set to Y too.
|
| /drivers/accessibility/speakup/ |
| D | Kconfig | 26 must answer either y or m to at least one of the
31 These drivers are not standalone drivers, but must be
121 In order to use the DecTalk PC driver, you must download
124 contains the software which must be pre-loaded on to the
126 This driver must be built as a module, and can not be
|
| /drivers/staging/pi433/Documentation/devicetree/ |
| D | pi433.txt | 4 - compatible: must be "Smarthome-Wolf,pi433"
6 - DIOx-gpio must be dedicated to the GPIO, connected with DIOx of the RFM69 module
|
| /drivers/staging/iio/Documentation/ |
| D | inkernel.txt | 31 The driver must provide datasheet_name values for its channels and
32 must pass the iio_map structures and a pointer to its own iio_dev structure
|
| /drivers/soc/litex/ |
| D | Kconfig | 17 All drivers that use functions from litex.h must depend on
|
| /drivers/net/ethernet/chelsio/cxgb4vf/ |
| D | t4vf_defs.h | 69 #error T4VF_MBDATA_BASE_ADDR must match CIM_PF_MAILBOX_DATA_A!
|
| /drivers/visorbus/ |
| D | Kconfig | 14 discover devices on an s-Par guest, and must be present for any other
|
| /drivers/gpu/drm/lima/ |
| D | lima_device.c | 214 bool must = desc->must_have[dev->id]; in lima_init_ip() local
224 err = must ? platform_get_irq_byname(pdev, irq_name) : in lima_init_ip()
238 return must ? err : 0; in lima_init_ip()
|
| /drivers/net/ipa/ |
| D | Kconfig | 20 Note that if selected, the selection type must match that
|
| /drivers/staging/sm750fb/ |
| D | TODO | 9 - must be ported to the atomic kms framework in the drm subsystem (which will
|
| /drivers/input/joystick/iforce/ |
| D | Kconfig | 11 You also must choose at least one of the two options below.
|
| /drivers/pps/clients/ |
| D | Kconfig | 35 GPIO. To be useful you must also register a platform device
|
| /drivers/net/can/softing/ |
| D | Kconfig | 17 must bring down the other bus too temporarily.
|
| /drivers/soc/bcm/ |
| D | Kconfig | 14 must be accessed using the RASPBERRYPI_POWER driver
|
| /drivers/scsi/aic7xxx/ |
| D | aic7xxx.seq | 11 * 1. Redistributions of source code must retain the above copyright
14 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
16 * ("Disclaimer") and any redistribution must be conditioned upon
54 * bus arbitration. The problem with this is that we must keep track of the
246 * Our first message must be one of IDENTIFY, ABORT, or
266 * If this is a tagged request, the tagged message must
285 * we've got a failed selection and must transition to bus
859 /* The lowest address byte must be loaded last. */
1075 * data must be "fixed up" once the transfer is halted.
1228 * The lowest address byte must be loaded
[all …]
|
| /drivers/crypto/nx/ |
| D | Kconfig | 24 drivers must be selected also. If you choose 'M' here, this
|
| /drivers/staging/media/av7110/ |
| D | video-command.rst | 65 /* The structure must be zeroed before use by the application
|
| /drivers/net/hippi/ |
| D | Kconfig | 16 under Linux, say Y here (you must also remember to enable the driver
|
| /drivers/media/radio/ |
| D | Kconfig | 50 you must connect the line out connector to a sound card or a
62 you must connect the line out connector to a sound card or a
149 you must connect the line out connector to a sound card or a
269 If you have a GemTeks combined (PnP) sound- and radio card you must
271 You must also pass the module a suitable io parameter, 0x248 has
|
1234