1 /* SPDX-License-Identifier: GPL-2.0-or-later */
2 /*------------------------------------------------------------------------
3 . smc91x.h - macros for SMSC's 91C9x/91C1xx single-chip Ethernet device.
4 .
5 . Copyright (C) 1996 by Erik Stahlman
6 . Copyright (C) 2001 Standard Microsystems Corporation
7 . Developed by Simple Network Magic Corporation
8 . Copyright (C) 2003 Monta Vista Software, Inc.
9 . Unified SMC91x driver by Nicolas Pitre
10 .
11 .
12 . Information contained in this file was obtained from the LAN91C111
13 . manual from SMC. To get a copy, if you really want one, you can find
14 . information under www.smsc.com.
15 .
16 . Authors
17 . Erik Stahlman <erik@vt.edu>
18 . Daris A Nevil <dnevil@snmc.com>
19 . Nicolas Pitre <nico@fluxnic.net>
20 .
21 ---------------------------------------------------------------------------*/
22 #ifndef _SMC91X_H_
23 #define _SMC91X_H_
24
25 #include <linux/dmaengine.h>
26 #include <linux/smc91x.h>
27
28 /*
29 * Any 16-bit access is performed with two 8-bit accesses if the hardware
30 * can't do it directly. Most registers are 16-bit so those are mandatory.
31 */
32 #define SMC_outw_b(x, a, r) \
33 do { \
34 unsigned int __val16 = (x); \
35 unsigned int __reg = (r); \
36 SMC_outb(__val16, a, __reg); \
37 SMC_outb(__val16 >> 8, a, __reg + (1 << SMC_IO_SHIFT)); \
38 } while (0)
39
40 #define SMC_inw_b(a, r) \
41 ({ \
42 unsigned int __val16; \
43 unsigned int __reg = r; \
44 __val16 = SMC_inb(a, __reg); \
45 __val16 |= SMC_inb(a, __reg + (1 << SMC_IO_SHIFT)) << 8; \
46 __val16; \
47 })
48
49 /*
50 * Define your architecture specific bus configuration parameters here.
51 */
52
53 #if defined(CONFIG_ARM)
54
55 #include <asm/mach-types.h>
56
57 /* Now the bus width is specified in the platform data
58 * pretend here to support all I/O access types
59 */
60 #define SMC_CAN_USE_8BIT 1
61 #define SMC_CAN_USE_16BIT 1
62 #define SMC_CAN_USE_32BIT 1
63 #define SMC_NOWAIT 1
64
65 #define SMC_IO_SHIFT (lp->io_shift)
66
67 #define SMC_inb(a, r) readb((a) + (r))
68 #define SMC_inw(a, r) \
69 ({ \
70 unsigned int __smc_r = r; \
71 SMC_16BIT(lp) ? readw((a) + __smc_r) : \
72 SMC_8BIT(lp) ? SMC_inw_b(a, __smc_r) : \
73 ({ BUG(); 0; }); \
74 })
75
76 #define SMC_inl(a, r) readl((a) + (r))
77 #define SMC_outb(v, a, r) writeb(v, (a) + (r))
78 #define SMC_outw(lp, v, a, r) \
79 do { \
80 unsigned int __v = v, __smc_r = r; \
81 if (SMC_16BIT(lp)) \
82 __SMC_outw(lp, __v, a, __smc_r); \
83 else if (SMC_8BIT(lp)) \
84 SMC_outw_b(__v, a, __smc_r); \
85 else \
86 BUG(); \
87 } while (0)
88
89 #define SMC_outl(v, a, r) writel(v, (a) + (r))
90 #define SMC_insb(a, r, p, l) readsb((a) + (r), p, l)
91 #define SMC_outsb(a, r, p, l) writesb((a) + (r), p, l)
92 #define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
93 #define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
94 #define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
95 #define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
96 #define SMC_IRQ_FLAGS (-1) /* from resource */
97
98 /* We actually can't write halfwords properly if not word aligned */
_SMC_outw_align4(u16 val,void __iomem * ioaddr,int reg,bool use_align4_workaround)99 static inline void _SMC_outw_align4(u16 val, void __iomem *ioaddr, int reg,
100 bool use_align4_workaround)
101 {
102 if (use_align4_workaround) {
103 unsigned int v = val << 16;
104 v |= readl(ioaddr + (reg & ~2)) & 0xffff;
105 writel(v, ioaddr + (reg & ~2));
106 } else {
107 writew(val, ioaddr + reg);
108 }
109 }
110
111 #define __SMC_outw(lp, v, a, r) \
112 _SMC_outw_align4((v), (a), (r), \
113 IS_BUILTIN(CONFIG_ARCH_PXA) && ((r) & 2) && \
114 (lp)->cfg.pxa_u16_align4)
115
116
117 #elif defined(CONFIG_SH_SH4202_MICRODEV)
118
119 #define SMC_CAN_USE_8BIT 0
120 #define SMC_CAN_USE_16BIT 1
121 #define SMC_CAN_USE_32BIT 0
122
123 #define SMC_inb(a, r) inb((a) + (r) - 0xa0000000)
124 #define SMC_inw(a, r) inw((a) + (r) - 0xa0000000)
125 #define SMC_inl(a, r) inl((a) + (r) - 0xa0000000)
126 #define SMC_outb(v, a, r) outb(v, (a) + (r) - 0xa0000000)
127 #define SMC_outw(lp, v, a, r) outw(v, (a) + (r) - 0xa0000000)
128 #define SMC_outl(v, a, r) outl(v, (a) + (r) - 0xa0000000)
129 #define SMC_insl(a, r, p, l) insl((a) + (r) - 0xa0000000, p, l)
130 #define SMC_outsl(a, r, p, l) outsl((a) + (r) - 0xa0000000, p, l)
131 #define SMC_insw(a, r, p, l) insw((a) + (r) - 0xa0000000, p, l)
132 #define SMC_outsw(a, r, p, l) outsw((a) + (r) - 0xa0000000, p, l)
133
134 #define SMC_IRQ_FLAGS (0)
135
136 #elif defined(CONFIG_ATARI)
137
138 #define SMC_CAN_USE_8BIT 1
139 #define SMC_CAN_USE_16BIT 1
140 #define SMC_CAN_USE_32BIT 1
141 #define SMC_NOWAIT 1
142
143 #define SMC_inb(a, r) readb((a) + (r))
144 #define SMC_inw(a, r) readw((a) + (r))
145 #define SMC_inl(a, r) readl((a) + (r))
146 #define SMC_outb(v, a, r) writeb(v, (a) + (r))
147 #define SMC_outw(lp, v, a, r) writew(v, (a) + (r))
148 #define SMC_outl(v, a, r) writel(v, (a) + (r))
149 #define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
150 #define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
151 #define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
152 #define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
153
154 #define RPC_LSA_DEFAULT RPC_LED_100_10
155 #define RPC_LSB_DEFAULT RPC_LED_TX_RX
156
157 #elif defined(CONFIG_COLDFIRE)
158
159 #define SMC_CAN_USE_8BIT 0
160 #define SMC_CAN_USE_16BIT 1
161 #define SMC_CAN_USE_32BIT 0
162 #define SMC_NOWAIT 1
163
mcf_insw(void * a,unsigned char * p,int l)164 static inline void mcf_insw(void *a, unsigned char *p, int l)
165 {
166 u16 *wp = (u16 *) p;
167 while (l-- > 0)
168 *wp++ = readw(a);
169 }
170
mcf_outsw(void * a,unsigned char * p,int l)171 static inline void mcf_outsw(void *a, unsigned char *p, int l)
172 {
173 u16 *wp = (u16 *) p;
174 while (l-- > 0)
175 writew(*wp++, a);
176 }
177
178 #define SMC_inw(a, r) _swapw(readw((a) + (r)))
179 #define SMC_outw(lp, v, a, r) writew(_swapw(v), (a) + (r))
180 #define SMC_insw(a, r, p, l) mcf_insw(a + r, p, l)
181 #define SMC_outsw(a, r, p, l) mcf_outsw(a + r, p, l)
182
183 #define SMC_IRQ_FLAGS 0
184
185 #else
186
187 /*
188 * Default configuration
189 */
190
191 #define SMC_CAN_USE_8BIT 1
192 #define SMC_CAN_USE_16BIT 1
193 #define SMC_CAN_USE_32BIT 1
194 #define SMC_NOWAIT 1
195
196 #define SMC_IO_SHIFT (lp->io_shift)
197
198 #define SMC_inb(a, r) ioread8((a) + (r))
199 #define SMC_inw(a, r) ioread16((a) + (r))
200 #define SMC_inl(a, r) ioread32((a) + (r))
201 #define SMC_outb(v, a, r) iowrite8(v, (a) + (r))
202 #define SMC_outw(lp, v, a, r) iowrite16(v, (a) + (r))
203 #define SMC_outl(v, a, r) iowrite32(v, (a) + (r))
204 #define SMC_insw(a, r, p, l) ioread16_rep((a) + (r), p, l)
205 #define SMC_outsw(a, r, p, l) iowrite16_rep((a) + (r), p, l)
206 #define SMC_insl(a, r, p, l) ioread32_rep((a) + (r), p, l)
207 #define SMC_outsl(a, r, p, l) iowrite32_rep((a) + (r), p, l)
208
209 #define RPC_LSA_DEFAULT RPC_LED_100_10
210 #define RPC_LSB_DEFAULT RPC_LED_TX_RX
211
212 #endif
213
214
215 /* store this information for the driver.. */
216 struct smc_local {
217 /*
218 * If I have to wait until memory is available to send a
219 * packet, I will store the skbuff here, until I get the
220 * desired memory. Then, I'll send it out and free it.
221 */
222 struct sk_buff *pending_tx_skb;
223 struct tasklet_struct tx_task;
224
225 struct gpio_desc *power_gpio;
226 struct gpio_desc *reset_gpio;
227
228 /* version/revision of the SMC91x chip */
229 int version;
230
231 /* Contains the current active transmission mode */
232 int tcr_cur_mode;
233
234 /* Contains the current active receive mode */
235 int rcr_cur_mode;
236
237 /* Contains the current active receive/phy mode */
238 int rpc_cur_mode;
239 int ctl_rfduplx;
240 int ctl_rspeed;
241
242 u32 msg_enable;
243 u32 phy_type;
244 struct mii_if_info mii;
245
246 /* work queue */
247 struct work_struct phy_configure;
248 struct net_device *dev;
249 int work_pending;
250
251 spinlock_t lock;
252
253 #ifdef CONFIG_ARCH_PXA
254 /* DMA needs the physical address of the chip */
255 u_long physaddr;
256 struct device *device;
257 #endif
258 struct dma_chan *dma_chan;
259 void __iomem *base;
260 void __iomem *datacs;
261
262 /* the low address lines on some platforms aren't connected... */
263 int io_shift;
264 /* on some platforms a u16 write must be 4-bytes aligned */
265 bool half_word_align4;
266
267 struct smc91x_platdata cfg;
268 };
269
270 #define SMC_8BIT(p) ((p)->cfg.flags & SMC91X_USE_8BIT)
271 #define SMC_16BIT(p) ((p)->cfg.flags & SMC91X_USE_16BIT)
272 #define SMC_32BIT(p) ((p)->cfg.flags & SMC91X_USE_32BIT)
273
274 #ifdef CONFIG_ARCH_PXA
275 /*
276 * Let's use the DMA engine on the XScale PXA2xx for RX packets. This is
277 * always happening in irq context so no need to worry about races. TX is
278 * different and probably not worth it for that reason, and not as critical
279 * as RX which can overrun memory and lose packets.
280 */
281 #include <linux/dma-mapping.h>
282
283 #ifdef SMC_insl
284 #undef SMC_insl
285 #define SMC_insl(a, r, p, l) \
286 smc_pxa_dma_insl(a, lp, r, dev->dma, p, l)
287 static inline void
smc_pxa_dma_inpump(struct smc_local * lp,u_char * buf,int len)288 smc_pxa_dma_inpump(struct smc_local *lp, u_char *buf, int len)
289 {
290 dma_addr_t dmabuf;
291 struct dma_async_tx_descriptor *tx;
292 dma_cookie_t cookie;
293 enum dma_status status;
294 struct dma_tx_state state;
295
296 dmabuf = dma_map_single(lp->device, buf, len, DMA_FROM_DEVICE);
297 tx = dmaengine_prep_slave_single(lp->dma_chan, dmabuf, len,
298 DMA_DEV_TO_MEM, 0);
299 if (tx) {
300 cookie = dmaengine_submit(tx);
301 dma_async_issue_pending(lp->dma_chan);
302 do {
303 status = dmaengine_tx_status(lp->dma_chan, cookie,
304 &state);
305 cpu_relax();
306 } while (status != DMA_COMPLETE && status != DMA_ERROR &&
307 state.residue);
308 dmaengine_terminate_all(lp->dma_chan);
309 }
310 dma_unmap_single(lp->device, dmabuf, len, DMA_FROM_DEVICE);
311 }
312
313 static inline void
smc_pxa_dma_insl(void __iomem * ioaddr,struct smc_local * lp,int reg,int dma,u_char * buf,int len)314 smc_pxa_dma_insl(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma,
315 u_char *buf, int len)
316 {
317 struct dma_slave_config config;
318 int ret;
319
320 /* fallback if no DMA available */
321 if (!lp->dma_chan) {
322 readsl(ioaddr + reg, buf, len);
323 return;
324 }
325
326 /* 64 bit alignment is required for memory to memory DMA */
327 if ((long)buf & 4) {
328 *((u32 *)buf) = SMC_inl(ioaddr, reg);
329 buf += 4;
330 len--;
331 }
332
333 memset(&config, 0, sizeof(config));
334 config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
335 config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
336 config.src_addr = lp->physaddr + reg;
337 config.dst_addr = lp->physaddr + reg;
338 config.src_maxburst = 32;
339 config.dst_maxburst = 32;
340 ret = dmaengine_slave_config(lp->dma_chan, &config);
341 if (ret) {
342 dev_err(lp->device, "dma channel configuration failed: %d\n",
343 ret);
344 return;
345 }
346
347 len *= 4;
348 smc_pxa_dma_inpump(lp, buf, len);
349 }
350 #endif
351
352 #ifdef SMC_insw
353 #undef SMC_insw
354 #define SMC_insw(a, r, p, l) \
355 smc_pxa_dma_insw(a, lp, r, dev->dma, p, l)
356 static inline void
smc_pxa_dma_insw(void __iomem * ioaddr,struct smc_local * lp,int reg,int dma,u_char * buf,int len)357 smc_pxa_dma_insw(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma,
358 u_char *buf, int len)
359 {
360 struct dma_slave_config config;
361 int ret;
362
363 /* fallback if no DMA available */
364 if (!lp->dma_chan) {
365 readsw(ioaddr + reg, buf, len);
366 return;
367 }
368
369 /* 64 bit alignment is required for memory to memory DMA */
370 while ((long)buf & 6) {
371 *((u16 *)buf) = SMC_inw(ioaddr, reg);
372 buf += 2;
373 len--;
374 }
375
376 memset(&config, 0, sizeof(config));
377 config.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
378 config.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
379 config.src_addr = lp->physaddr + reg;
380 config.dst_addr = lp->physaddr + reg;
381 config.src_maxburst = 32;
382 config.dst_maxburst = 32;
383 ret = dmaengine_slave_config(lp->dma_chan, &config);
384 if (ret) {
385 dev_err(lp->device, "dma channel configuration failed: %d\n",
386 ret);
387 return;
388 }
389
390 len *= 2;
391 smc_pxa_dma_inpump(lp, buf, len);
392 }
393 #endif
394
395 #endif /* CONFIG_ARCH_PXA */
396
397
398 /*
399 * Everything a particular hardware setup needs should have been defined
400 * at this point. Add stubs for the undefined cases, mainly to avoid
401 * compilation warnings since they'll be optimized away, or to prevent buggy
402 * use of them.
403 */
404
405 #if ! SMC_CAN_USE_32BIT
406 #define SMC_inl(ioaddr, reg) ({ BUG(); 0; })
407 #define SMC_outl(x, ioaddr, reg) BUG()
408 #define SMC_insl(a, r, p, l) BUG()
409 #define SMC_outsl(a, r, p, l) BUG()
410 #endif
411
412 #if !defined(SMC_insl) || !defined(SMC_outsl)
413 #define SMC_insl(a, r, p, l) BUG()
414 #define SMC_outsl(a, r, p, l) BUG()
415 #endif
416
417 #if ! SMC_CAN_USE_16BIT
418
419 #define SMC_outw(lp, x, ioaddr, reg) SMC_outw_b(x, ioaddr, reg)
420 #define SMC_inw(ioaddr, reg) SMC_inw_b(ioaddr, reg)
421 #define SMC_insw(a, r, p, l) BUG()
422 #define SMC_outsw(a, r, p, l) BUG()
423
424 #endif
425
426 #if !defined(SMC_insw) || !defined(SMC_outsw)
427 #define SMC_insw(a, r, p, l) BUG()
428 #define SMC_outsw(a, r, p, l) BUG()
429 #endif
430
431 #if ! SMC_CAN_USE_8BIT
432 #undef SMC_inb
433 #define SMC_inb(ioaddr, reg) ({ BUG(); 0; })
434 #undef SMC_outb
435 #define SMC_outb(x, ioaddr, reg) BUG()
436 #define SMC_insb(a, r, p, l) BUG()
437 #define SMC_outsb(a, r, p, l) BUG()
438 #endif
439
440 #if !defined(SMC_insb) || !defined(SMC_outsb)
441 #define SMC_insb(a, r, p, l) BUG()
442 #define SMC_outsb(a, r, p, l) BUG()
443 #endif
444
445 #ifndef SMC_CAN_USE_DATACS
446 #define SMC_CAN_USE_DATACS 0
447 #endif
448
449 #ifndef SMC_IO_SHIFT
450 #define SMC_IO_SHIFT 0
451 #endif
452
453 #ifndef SMC_IRQ_FLAGS
454 #define SMC_IRQ_FLAGS IRQF_TRIGGER_RISING
455 #endif
456
457 #ifndef SMC_INTERRUPT_PREAMBLE
458 #define SMC_INTERRUPT_PREAMBLE
459 #endif
460
461
462 /* Because of bank switching, the LAN91x uses only 16 I/O ports */
463 #define SMC_IO_EXTENT (16 << SMC_IO_SHIFT)
464 #define SMC_DATA_EXTENT (4)
465
466 /*
467 . Bank Select Register:
468 .
469 . yyyy yyyy 0000 00xx
470 . xx = bank number
471 . yyyy yyyy = 0x33, for identification purposes.
472 */
473 #define BANK_SELECT (14 << SMC_IO_SHIFT)
474
475
476 // Transmit Control Register
477 /* BANK 0 */
478 #define TCR_REG(lp) SMC_REG(lp, 0x0000, 0)
479 #define TCR_ENABLE 0x0001 // When 1 we can transmit
480 #define TCR_LOOP 0x0002 // Controls output pin LBK
481 #define TCR_FORCOL 0x0004 // When 1 will force a collision
482 #define TCR_PAD_EN 0x0080 // When 1 will pad tx frames < 64 bytes w/0
483 #define TCR_NOCRC 0x0100 // When 1 will not append CRC to tx frames
484 #define TCR_MON_CSN 0x0400 // When 1 tx monitors carrier
485 #define TCR_FDUPLX 0x0800 // When 1 enables full duplex operation
486 #define TCR_STP_SQET 0x1000 // When 1 stops tx if Signal Quality Error
487 #define TCR_EPH_LOOP 0x2000 // When 1 enables EPH block loopback
488 #define TCR_SWFDUP 0x8000 // When 1 enables Switched Full Duplex mode
489
490 #define TCR_CLEAR 0 /* do NOTHING */
491 /* the default settings for the TCR register : */
492 #define TCR_DEFAULT (TCR_ENABLE | TCR_PAD_EN)
493
494
495 // EPH Status Register
496 /* BANK 0 */
497 #define EPH_STATUS_REG(lp) SMC_REG(lp, 0x0002, 0)
498 #define ES_TX_SUC 0x0001 // Last TX was successful
499 #define ES_SNGL_COL 0x0002 // Single collision detected for last tx
500 #define ES_MUL_COL 0x0004 // Multiple collisions detected for last tx
501 #define ES_LTX_MULT 0x0008 // Last tx was a multicast
502 #define ES_16COL 0x0010 // 16 Collisions Reached
503 #define ES_SQET 0x0020 // Signal Quality Error Test
504 #define ES_LTXBRD 0x0040 // Last tx was a broadcast
505 #define ES_TXDEFR 0x0080 // Transmit Deferred
506 #define ES_LATCOL 0x0200 // Late collision detected on last tx
507 #define ES_LOSTCARR 0x0400 // Lost Carrier Sense
508 #define ES_EXC_DEF 0x0800 // Excessive Deferral
509 #define ES_CTR_ROL 0x1000 // Counter Roll Over indication
510 #define ES_LINK_OK 0x4000 // Driven by inverted value of nLNK pin
511 #define ES_TXUNRN 0x8000 // Tx Underrun
512
513
514 // Receive Control Register
515 /* BANK 0 */
516 #define RCR_REG(lp) SMC_REG(lp, 0x0004, 0)
517 #define RCR_RX_ABORT 0x0001 // Set if a rx frame was aborted
518 #define RCR_PRMS 0x0002 // Enable promiscuous mode
519 #define RCR_ALMUL 0x0004 // When set accepts all multicast frames
520 #define RCR_RXEN 0x0100 // IFF this is set, we can receive packets
521 #define RCR_STRIP_CRC 0x0200 // When set strips CRC from rx packets
522 #define RCR_ABORT_ENB 0x0200 // When set will abort rx on collision
523 #define RCR_FILT_CAR 0x0400 // When set filters leading 12 bit s of carrier
524 #define RCR_SOFTRST 0x8000 // resets the chip
525
526 /* the normal settings for the RCR register : */
527 #define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN)
528 #define RCR_CLEAR 0x0 // set it to a base state
529
530
531 // Counter Register
532 /* BANK 0 */
533 #define COUNTER_REG(lp) SMC_REG(lp, 0x0006, 0)
534
535
536 // Memory Information Register
537 /* BANK 0 */
538 #define MIR_REG(lp) SMC_REG(lp, 0x0008, 0)
539
540
541 // Receive/Phy Control Register
542 /* BANK 0 */
543 #define RPC_REG(lp) SMC_REG(lp, 0x000A, 0)
544 #define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode.
545 #define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode
546 #define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode
547 #define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb
548 #define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb
549
550 #ifndef RPC_LSA_DEFAULT
551 #define RPC_LSA_DEFAULT RPC_LED_100
552 #endif
553 #ifndef RPC_LSB_DEFAULT
554 #define RPC_LSB_DEFAULT RPC_LED_FD
555 #endif
556
557 #define RPC_DEFAULT (RPC_ANEG | RPC_SPEED | RPC_DPLX)
558
559
560 /* Bank 0 0x0C is reserved */
561
562 // Bank Select Register
563 /* All Banks */
564 #define BSR_REG 0x000E
565
566
567 // Configuration Reg
568 /* BANK 1 */
569 #define CONFIG_REG(lp) SMC_REG(lp, 0x0000, 1)
570 #define CONFIG_EXT_PHY 0x0200 // 1=external MII, 0=internal Phy
571 #define CONFIG_GPCNTRL 0x0400 // Inverse value drives pin nCNTRL
572 #define CONFIG_NO_WAIT 0x1000 // When 1 no extra wait states on ISA bus
573 #define CONFIG_EPH_POWER_EN 0x8000 // When 0 EPH is placed into low power mode.
574
575 // Default is powered-up, Internal Phy, Wait States, and pin nCNTRL=low
576 #define CONFIG_DEFAULT (CONFIG_EPH_POWER_EN)
577
578
579 // Base Address Register
580 /* BANK 1 */
581 #define BASE_REG(lp) SMC_REG(lp, 0x0002, 1)
582
583
584 // Individual Address Registers
585 /* BANK 1 */
586 #define ADDR0_REG(lp) SMC_REG(lp, 0x0004, 1)
587 #define ADDR1_REG(lp) SMC_REG(lp, 0x0006, 1)
588 #define ADDR2_REG(lp) SMC_REG(lp, 0x0008, 1)
589
590
591 // General Purpose Register
592 /* BANK 1 */
593 #define GP_REG(lp) SMC_REG(lp, 0x000A, 1)
594
595
596 // Control Register
597 /* BANK 1 */
598 #define CTL_REG(lp) SMC_REG(lp, 0x000C, 1)
599 #define CTL_RCV_BAD 0x4000 // When 1 bad CRC packets are received
600 #define CTL_AUTO_RELEASE 0x0800 // When 1 tx pages are released automatically
601 #define CTL_LE_ENABLE 0x0080 // When 1 enables Link Error interrupt
602 #define CTL_CR_ENABLE 0x0040 // When 1 enables Counter Rollover interrupt
603 #define CTL_TE_ENABLE 0x0020 // When 1 enables Transmit Error interrupt
604 #define CTL_EEPROM_SELECT 0x0004 // Controls EEPROM reload & store
605 #define CTL_RELOAD 0x0002 // When set reads EEPROM into registers
606 #define CTL_STORE 0x0001 // When set stores registers into EEPROM
607
608
609 // MMU Command Register
610 /* BANK 2 */
611 #define MMU_CMD_REG(lp) SMC_REG(lp, 0x0000, 2)
612 #define MC_BUSY 1 // When 1 the last release has not completed
613 #define MC_NOP (0<<5) // No Op
614 #define MC_ALLOC (1<<5) // OR with number of 256 byte packets
615 #define MC_RESET (2<<5) // Reset MMU to initial state
616 #define MC_REMOVE (3<<5) // Remove the current rx packet
617 #define MC_RELEASE (4<<5) // Remove and release the current rx packet
618 #define MC_FREEPKT (5<<5) // Release packet in PNR register
619 #define MC_ENQUEUE (6<<5) // Enqueue the packet for transmit
620 #define MC_RSTTXFIFO (7<<5) // Reset the TX FIFOs
621
622
623 // Packet Number Register
624 /* BANK 2 */
625 #define PN_REG(lp) SMC_REG(lp, 0x0002, 2)
626
627
628 // Allocation Result Register
629 /* BANK 2 */
630 #define AR_REG(lp) SMC_REG(lp, 0x0003, 2)
631 #define AR_FAILED 0x80 // Alocation Failed
632
633
634 // TX FIFO Ports Register
635 /* BANK 2 */
636 #define TXFIFO_REG(lp) SMC_REG(lp, 0x0004, 2)
637 #define TXFIFO_TEMPTY 0x80 // TX FIFO Empty
638
639 // RX FIFO Ports Register
640 /* BANK 2 */
641 #define RXFIFO_REG(lp) SMC_REG(lp, 0x0005, 2)
642 #define RXFIFO_REMPTY 0x80 // RX FIFO Empty
643
644 #define FIFO_REG(lp) SMC_REG(lp, 0x0004, 2)
645
646 // Pointer Register
647 /* BANK 2 */
648 #define PTR_REG(lp) SMC_REG(lp, 0x0006, 2)
649 #define PTR_RCV 0x8000 // 1=Receive area, 0=Transmit area
650 #define PTR_AUTOINC 0x4000 // Auto increment the pointer on each access
651 #define PTR_READ 0x2000 // When 1 the operation is a read
652
653
654 // Data Register
655 /* BANK 2 */
656 #define DATA_REG(lp) SMC_REG(lp, 0x0008, 2)
657
658
659 // Interrupt Status/Acknowledge Register
660 /* BANK 2 */
661 #define INT_REG(lp) SMC_REG(lp, 0x000C, 2)
662
663
664 // Interrupt Mask Register
665 /* BANK 2 */
666 #define IM_REG(lp) SMC_REG(lp, 0x000D, 2)
667 #define IM_MDINT 0x80 // PHY MI Register 18 Interrupt
668 #define IM_ERCV_INT 0x40 // Early Receive Interrupt
669 #define IM_EPH_INT 0x20 // Set by Ethernet Protocol Handler section
670 #define IM_RX_OVRN_INT 0x10 // Set by Receiver Overruns
671 #define IM_ALLOC_INT 0x08 // Set when allocation request is completed
672 #define IM_TX_EMPTY_INT 0x04 // Set if the TX FIFO goes empty
673 #define IM_TX_INT 0x02 // Transmit Interrupt
674 #define IM_RCV_INT 0x01 // Receive Interrupt
675
676
677 // Multicast Table Registers
678 /* BANK 3 */
679 #define MCAST_REG1(lp) SMC_REG(lp, 0x0000, 3)
680 #define MCAST_REG2(lp) SMC_REG(lp, 0x0002, 3)
681 #define MCAST_REG3(lp) SMC_REG(lp, 0x0004, 3)
682 #define MCAST_REG4(lp) SMC_REG(lp, 0x0006, 3)
683
684
685 // Management Interface Register (MII)
686 /* BANK 3 */
687 #define MII_REG(lp) SMC_REG(lp, 0x0008, 3)
688 #define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup
689 #define MII_MDOE 0x0008 // MII Output Enable
690 #define MII_MCLK 0x0004 // MII Clock, pin MDCLK
691 #define MII_MDI 0x0002 // MII Input, pin MDI
692 #define MII_MDO 0x0001 // MII Output, pin MDO
693
694
695 // Revision Register
696 /* BANK 3 */
697 /* ( hi: chip id low: rev # ) */
698 #define REV_REG(lp) SMC_REG(lp, 0x000A, 3)
699
700
701 // Early RCV Register
702 /* BANK 3 */
703 /* this is NOT on SMC9192 */
704 #define ERCV_REG(lp) SMC_REG(lp, 0x000C, 3)
705 #define ERCV_RCV_DISCRD 0x0080 // When 1 discards a packet being received
706 #define ERCV_THRESHOLD 0x001F // ERCV Threshold Mask
707
708
709 // External Register
710 /* BANK 7 */
711 #define EXT_REG(lp) SMC_REG(lp, 0x0000, 7)
712
713
714 #define CHIP_9192 3
715 #define CHIP_9194 4
716 #define CHIP_9195 5
717 #define CHIP_9196 6
718 #define CHIP_91100 7
719 #define CHIP_91100FD 8
720 #define CHIP_91111FD 9
721
722 static const char * chip_ids[ 16 ] = {
723 NULL, NULL, NULL,
724 /* 3 */ "SMC91C90/91C92",
725 /* 4 */ "SMC91C94",
726 /* 5 */ "SMC91C95",
727 /* 6 */ "SMC91C96",
728 /* 7 */ "SMC91C100",
729 /* 8 */ "SMC91C100FD",
730 /* 9 */ "SMC91C11xFD",
731 NULL, NULL, NULL,
732 NULL, NULL, NULL};
733
734
735 /*
736 . Receive status bits
737 */
738 #define RS_ALGNERR 0x8000
739 #define RS_BRODCAST 0x4000
740 #define RS_BADCRC 0x2000
741 #define RS_ODDFRAME 0x1000
742 #define RS_TOOLONG 0x0800
743 #define RS_TOOSHORT 0x0400
744 #define RS_MULTICAST 0x0001
745 #define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT)
746
747
748 /*
749 * PHY IDs
750 * LAN83C183 == LAN91C111 Internal PHY
751 */
752 #define PHY_LAN83C183 0x0016f840
753 #define PHY_LAN83C180 0x02821c50
754
755 /*
756 * PHY Register Addresses (LAN91C111 Internal PHY)
757 *
758 * Generic PHY registers can be found in <linux/mii.h>
759 *
760 * These phy registers are specific to our on-board phy.
761 */
762
763 // PHY Configuration Register 1
764 #define PHY_CFG1_REG 0x10
765 #define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled
766 #define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled
767 #define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down
768 #define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler
769 #define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable
770 #define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled
771 #define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm)
772 #define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
773 #define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust
774 #define PHY_CFG1_TLVL_MASK 0x003C
775 #define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time
776
777
778 // PHY Configuration Register 2
779 #define PHY_CFG2_REG 0x11
780 #define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled
781 #define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled
782 #define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt)
783 #define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo
784
785 // PHY Status Output (and Interrupt status) Register
786 #define PHY_INT_REG 0x12 // Status Output (Interrupt Status)
787 #define PHY_INT_INT 0x8000 // 1=bits have changed since last read
788 #define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected
789 #define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync
790 #define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx
791 #define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx
792 #define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx
793 #define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected
794 #define PHY_INT_JAB 0x0100 // 1=Jabber detected
795 #define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode
796 #define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex
797
798 // PHY Interrupt/Status Mask Register
799 #define PHY_MASK_REG 0x13 // Interrupt Mask
800 // Uses the same bit definitions as PHY_INT_REG
801
802
803 /*
804 * SMC91C96 ethernet config and status registers.
805 * These are in the "attribute" space.
806 */
807 #define ECOR 0x8000
808 #define ECOR_RESET 0x80
809 #define ECOR_LEVEL_IRQ 0x40
810 #define ECOR_WR_ATTRIB 0x04
811 #define ECOR_ENABLE 0x01
812
813 #define ECSR 0x8002
814 #define ECSR_IOIS8 0x20
815 #define ECSR_PWRDWN 0x04
816 #define ECSR_INT 0x02
817
818 #define ATTRIB_SIZE ((64*1024) << SMC_IO_SHIFT)
819
820
821 /*
822 * Macros to abstract register access according to the data bus
823 * capabilities. Please use those and not the in/out primitives.
824 * Note: the following macros do *not* select the bank -- this must
825 * be done separately as needed in the main code. The SMC_REG() macro
826 * only uses the bank argument for debugging purposes (when enabled).
827 *
828 * Note: despite inline functions being safer, everything leading to this
829 * should preferably be macros to let BUG() display the line number in
830 * the core source code since we're interested in the top call site
831 * not in any inline function location.
832 */
833
834 #if SMC_DEBUG > 0
835 #define SMC_REG(lp, reg, bank) \
836 ({ \
837 int __b = SMC_CURRENT_BANK(lp); \
838 if (unlikely((__b & ~0xf0) != (0x3300 | bank))) { \
839 pr_err("%s: bank reg screwed (0x%04x)\n", \
840 CARDNAME, __b); \
841 BUG(); \
842 } \
843 reg<<SMC_IO_SHIFT; \
844 })
845 #else
846 #define SMC_REG(lp, reg, bank) (reg<<SMC_IO_SHIFT)
847 #endif
848
849 /*
850 * Hack Alert: Some setups just can't write 8 or 16 bits reliably when not
851 * aligned to a 32 bit boundary. I tell you that does exist!
852 * Fortunately the affected register accesses can be easily worked around
853 * since we can write zeroes to the preceding 16 bits without adverse
854 * effects and use a 32-bit access.
855 *
856 * Enforce it on any 32-bit capable setup for now.
857 */
858 #define SMC_MUST_ALIGN_WRITE(lp) SMC_32BIT(lp)
859
860 #define SMC_GET_PN(lp) \
861 (SMC_8BIT(lp) ? (SMC_inb(ioaddr, PN_REG(lp))) \
862 : (SMC_inw(ioaddr, PN_REG(lp)) & 0xFF))
863
864 #define SMC_SET_PN(lp, x) \
865 do { \
866 if (SMC_MUST_ALIGN_WRITE(lp)) \
867 SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 0, 2)); \
868 else if (SMC_8BIT(lp)) \
869 SMC_outb(x, ioaddr, PN_REG(lp)); \
870 else \
871 SMC_outw(lp, x, ioaddr, PN_REG(lp)); \
872 } while (0)
873
874 #define SMC_GET_AR(lp) \
875 (SMC_8BIT(lp) ? (SMC_inb(ioaddr, AR_REG(lp))) \
876 : (SMC_inw(ioaddr, PN_REG(lp)) >> 8))
877
878 #define SMC_GET_TXFIFO(lp) \
879 (SMC_8BIT(lp) ? (SMC_inb(ioaddr, TXFIFO_REG(lp))) \
880 : (SMC_inw(ioaddr, TXFIFO_REG(lp)) & 0xFF))
881
882 #define SMC_GET_RXFIFO(lp) \
883 (SMC_8BIT(lp) ? (SMC_inb(ioaddr, RXFIFO_REG(lp))) \
884 : (SMC_inw(ioaddr, TXFIFO_REG(lp)) >> 8))
885
886 #define SMC_GET_INT(lp) \
887 (SMC_8BIT(lp) ? (SMC_inb(ioaddr, INT_REG(lp))) \
888 : (SMC_inw(ioaddr, INT_REG(lp)) & 0xFF))
889
890 #define SMC_ACK_INT(lp, x) \
891 do { \
892 if (SMC_8BIT(lp)) \
893 SMC_outb(x, ioaddr, INT_REG(lp)); \
894 else { \
895 unsigned long __flags; \
896 int __mask; \
897 local_irq_save(__flags); \
898 __mask = SMC_inw(ioaddr, INT_REG(lp)) & ~0xff; \
899 SMC_outw(lp, __mask | (x), ioaddr, INT_REG(lp)); \
900 local_irq_restore(__flags); \
901 } \
902 } while (0)
903
904 #define SMC_GET_INT_MASK(lp) \
905 (SMC_8BIT(lp) ? (SMC_inb(ioaddr, IM_REG(lp))) \
906 : (SMC_inw(ioaddr, INT_REG(lp)) >> 8))
907
908 #define SMC_SET_INT_MASK(lp, x) \
909 do { \
910 if (SMC_8BIT(lp)) \
911 SMC_outb(x, ioaddr, IM_REG(lp)); \
912 else \
913 SMC_outw(lp, (x) << 8, ioaddr, INT_REG(lp)); \
914 } while (0)
915
916 #define SMC_CURRENT_BANK(lp) SMC_inw(ioaddr, BANK_SELECT)
917
918 #define SMC_SELECT_BANK(lp, x) \
919 do { \
920 if (SMC_MUST_ALIGN_WRITE(lp)) \
921 SMC_outl((x)<<16, ioaddr, 12<<SMC_IO_SHIFT); \
922 else \
923 SMC_outw(lp, x, ioaddr, BANK_SELECT); \
924 } while (0)
925
926 #define SMC_GET_BASE(lp) SMC_inw(ioaddr, BASE_REG(lp))
927
928 #define SMC_SET_BASE(lp, x) SMC_outw(lp, x, ioaddr, BASE_REG(lp))
929
930 #define SMC_GET_CONFIG(lp) SMC_inw(ioaddr, CONFIG_REG(lp))
931
932 #define SMC_SET_CONFIG(lp, x) SMC_outw(lp, x, ioaddr, CONFIG_REG(lp))
933
934 #define SMC_GET_COUNTER(lp) SMC_inw(ioaddr, COUNTER_REG(lp))
935
936 #define SMC_GET_CTL(lp) SMC_inw(ioaddr, CTL_REG(lp))
937
938 #define SMC_SET_CTL(lp, x) SMC_outw(lp, x, ioaddr, CTL_REG(lp))
939
940 #define SMC_GET_MII(lp) SMC_inw(ioaddr, MII_REG(lp))
941
942 #define SMC_GET_GP(lp) SMC_inw(ioaddr, GP_REG(lp))
943
944 #define SMC_SET_GP(lp, x) \
945 do { \
946 if (SMC_MUST_ALIGN_WRITE(lp)) \
947 SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 8, 1)); \
948 else \
949 SMC_outw(lp, x, ioaddr, GP_REG(lp)); \
950 } while (0)
951
952 #define SMC_SET_MII(lp, x) SMC_outw(lp, x, ioaddr, MII_REG(lp))
953
954 #define SMC_GET_MIR(lp) SMC_inw(ioaddr, MIR_REG(lp))
955
956 #define SMC_SET_MIR(lp, x) SMC_outw(lp, x, ioaddr, MIR_REG(lp))
957
958 #define SMC_GET_MMU_CMD(lp) SMC_inw(ioaddr, MMU_CMD_REG(lp))
959
960 #define SMC_SET_MMU_CMD(lp, x) SMC_outw(lp, x, ioaddr, MMU_CMD_REG(lp))
961
962 #define SMC_GET_FIFO(lp) SMC_inw(ioaddr, FIFO_REG(lp))
963
964 #define SMC_GET_PTR(lp) SMC_inw(ioaddr, PTR_REG(lp))
965
966 #define SMC_SET_PTR(lp, x) \
967 do { \
968 if (SMC_MUST_ALIGN_WRITE(lp)) \
969 SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 4, 2)); \
970 else \
971 SMC_outw(lp, x, ioaddr, PTR_REG(lp)); \
972 } while (0)
973
974 #define SMC_GET_EPH_STATUS(lp) SMC_inw(ioaddr, EPH_STATUS_REG(lp))
975
976 #define SMC_GET_RCR(lp) SMC_inw(ioaddr, RCR_REG(lp))
977
978 #define SMC_SET_RCR(lp, x) SMC_outw(lp, x, ioaddr, RCR_REG(lp))
979
980 #define SMC_GET_REV(lp) SMC_inw(ioaddr, REV_REG(lp))
981
982 #define SMC_GET_RPC(lp) SMC_inw(ioaddr, RPC_REG(lp))
983
984 #define SMC_SET_RPC(lp, x) \
985 do { \
986 if (SMC_MUST_ALIGN_WRITE(lp)) \
987 SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 8, 0)); \
988 else \
989 SMC_outw(lp, x, ioaddr, RPC_REG(lp)); \
990 } while (0)
991
992 #define SMC_GET_TCR(lp) SMC_inw(ioaddr, TCR_REG(lp))
993
994 #define SMC_SET_TCR(lp, x) SMC_outw(lp, x, ioaddr, TCR_REG(lp))
995
996 #ifndef SMC_GET_MAC_ADDR
997 #define SMC_GET_MAC_ADDR(lp, addr) \
998 do { \
999 unsigned int __v; \
1000 __v = SMC_inw(ioaddr, ADDR0_REG(lp)); \
1001 addr[0] = __v; addr[1] = __v >> 8; \
1002 __v = SMC_inw(ioaddr, ADDR1_REG(lp)); \
1003 addr[2] = __v; addr[3] = __v >> 8; \
1004 __v = SMC_inw(ioaddr, ADDR2_REG(lp)); \
1005 addr[4] = __v; addr[5] = __v >> 8; \
1006 } while (0)
1007 #endif
1008
1009 #define SMC_SET_MAC_ADDR(lp, addr) \
1010 do { \
1011 SMC_outw(lp, addr[0] | (addr[1] << 8), ioaddr, ADDR0_REG(lp)); \
1012 SMC_outw(lp, addr[2] | (addr[3] << 8), ioaddr, ADDR1_REG(lp)); \
1013 SMC_outw(lp, addr[4] | (addr[5] << 8), ioaddr, ADDR2_REG(lp)); \
1014 } while (0)
1015
1016 #define SMC_SET_MCAST(lp, x) \
1017 do { \
1018 const unsigned char *mt = (x); \
1019 SMC_outw(lp, mt[0] | (mt[1] << 8), ioaddr, MCAST_REG1(lp)); \
1020 SMC_outw(lp, mt[2] | (mt[3] << 8), ioaddr, MCAST_REG2(lp)); \
1021 SMC_outw(lp, mt[4] | (mt[5] << 8), ioaddr, MCAST_REG3(lp)); \
1022 SMC_outw(lp, mt[6] | (mt[7] << 8), ioaddr, MCAST_REG4(lp)); \
1023 } while (0)
1024
1025 #define SMC_PUT_PKT_HDR(lp, status, length) \
1026 do { \
1027 if (SMC_32BIT(lp)) \
1028 SMC_outl((status) | (length)<<16, ioaddr, \
1029 DATA_REG(lp)); \
1030 else { \
1031 SMC_outw(lp, status, ioaddr, DATA_REG(lp)); \
1032 SMC_outw(lp, length, ioaddr, DATA_REG(lp)); \
1033 } \
1034 } while (0)
1035
1036 #define SMC_GET_PKT_HDR(lp, status, length) \
1037 do { \
1038 if (SMC_32BIT(lp)) { \
1039 unsigned int __val = SMC_inl(ioaddr, DATA_REG(lp)); \
1040 (status) = __val & 0xffff; \
1041 (length) = __val >> 16; \
1042 } else { \
1043 (status) = SMC_inw(ioaddr, DATA_REG(lp)); \
1044 (length) = SMC_inw(ioaddr, DATA_REG(lp)); \
1045 } \
1046 } while (0)
1047
1048 #define SMC_PUSH_DATA(lp, p, l) \
1049 do { \
1050 if (SMC_32BIT(lp)) { \
1051 void *__ptr = (p); \
1052 int __len = (l); \
1053 void __iomem *__ioaddr = ioaddr; \
1054 if (__len >= 2 && (unsigned long)__ptr & 2) { \
1055 __len -= 2; \
1056 SMC_outsw(ioaddr, DATA_REG(lp), __ptr, 1); \
1057 __ptr += 2; \
1058 } \
1059 if (SMC_CAN_USE_DATACS && lp->datacs) \
1060 __ioaddr = lp->datacs; \
1061 SMC_outsl(__ioaddr, DATA_REG(lp), __ptr, __len>>2); \
1062 if (__len & 2) { \
1063 __ptr += (__len & ~3); \
1064 SMC_outsw(ioaddr, DATA_REG(lp), __ptr, 1); \
1065 } \
1066 } else if (SMC_16BIT(lp)) \
1067 SMC_outsw(ioaddr, DATA_REG(lp), p, (l) >> 1); \
1068 else if (SMC_8BIT(lp)) \
1069 SMC_outsb(ioaddr, DATA_REG(lp), p, l); \
1070 } while (0)
1071
1072 #define SMC_PULL_DATA(lp, p, l) \
1073 do { \
1074 if (SMC_32BIT(lp)) { \
1075 void *__ptr = (p); \
1076 int __len = (l); \
1077 void __iomem *__ioaddr = ioaddr; \
1078 if ((unsigned long)__ptr & 2) { \
1079 /* \
1080 * We want 32bit alignment here. \
1081 * Since some buses perform a full \
1082 * 32bit fetch even for 16bit data \
1083 * we can't use SMC_inw() here. \
1084 * Back both source (on-chip) and \
1085 * destination pointers of 2 bytes. \
1086 * This is possible since the call to \
1087 * SMC_GET_PKT_HDR() already advanced \
1088 * the source pointer of 4 bytes, and \
1089 * the skb_reserve(skb, 2) advanced \
1090 * the destination pointer of 2 bytes. \
1091 */ \
1092 __ptr -= 2; \
1093 __len += 2; \
1094 SMC_SET_PTR(lp, \
1095 2|PTR_READ|PTR_RCV|PTR_AUTOINC); \
1096 } \
1097 if (SMC_CAN_USE_DATACS && lp->datacs) \
1098 __ioaddr = lp->datacs; \
1099 __len += 2; \
1100 SMC_insl(__ioaddr, DATA_REG(lp), __ptr, __len>>2); \
1101 } else if (SMC_16BIT(lp)) \
1102 SMC_insw(ioaddr, DATA_REG(lp), p, (l) >> 1); \
1103 else if (SMC_8BIT(lp)) \
1104 SMC_insb(ioaddr, DATA_REG(lp), p, l); \
1105 } while (0)
1106
1107 #endif /* _SMC91X_H_ */
1108