| /drivers/video/fbdev/riva/ |
| D | riva_hw.h | 292 #ifdef Control
293 #undef Control
295 U032 Control; member
323 #ifdef Control
324 #undef Control
326 U032 Control; member
|
| /drivers/scsi/aic7xxx/ |
| D | aic79xx.reg | 258 * Host Control Register
379 * Queue Offset Control & Status
408 * Interrupt Control
424 * Data FIFO Control
501 * Arbiter Control
657 * ROM Control
839 * PCI-X Control
1524 * LQ Manager Control 0
1537 * LQ Manager Control 1
1551 * LQ Manager Control 2
[all …]
|
| D | aic7xxx.reg | 65 * SCSI Sequence Control (p. 3-11).
82 * SCSI Transfer Control 0 Register (pp. 3-13).
98 * SCSI Transfer Control 1 Register (pp. 3-14,15).
115 * SCSI Control Signal Read Register (p. 3-15).
144 * SCSI Control Signal Write Register (p. 3-16).
174 * SCSI Rate Control (p. 3-17).
547 * Serial EEPROM Control (p. 4-92 in 7870 Databook)
584 * SCSI Block Control (p. 3-32)
604 * Sequencer Control (p. 3-33)
734 * Board Control (p. 3-43)
[all …]
|
| /drivers/clk/keystone/ |
| D | Kconfig | 10 tristate "TI System Control Interface clock drivers"
15 This adds the clock driver support over TI System Control Interface.
|
| /drivers/soc/aspeed/ |
| D | Kconfig | 13 Control LPC firmware cycle mappings through ioctl()s. The driver
43 Control ASPEED P2A VGA MMIO to BMC mappings through ioctl()s. The
|
| /drivers/net/ethernet/atheros/atlx/ |
| D | atl2.c | 2176 u32 i, Control; in get_permanent_address() local
2194 if (atl2_read_eeprom(hw, i + 0x100, &Control)) { in get_permanent_address()
2197 Addr[0] = Control; in get_permanent_address()
2200 Addr[1] = Control; in get_permanent_address()
2202 } else if ((Control & 0xff) == 0x5A) { in get_permanent_address()
2204 Register = (u16) (Control >> 16); in get_permanent_address()
2232 if (atl2_spi_read(hw, i + 0x1f000, &Control)) { in get_permanent_address()
2235 Addr[0] = Control; in get_permanent_address()
2237 Addr[1] = Control; in get_permanent_address()
2239 } else if ((Control & 0xff) == 0x5A) { in get_permanent_address()
[all …]
|
| /drivers/clk/baikal-t1/ |
| D | Kconfig | 3 bool "Baikal-T1 Clocks Control Unit interface"
7 Clocks Control Unit is the core of Baikal-T1 SoC System Controller
|
| /drivers/clk/uniphier/ |
| D | Kconfig | 9 Say Y if you want to control clocks provided by System Control
|
| /drivers/firmware/arm_scmi/ |
| D | Kconfig | 2 menu "ARM System Control and Management Interface Protocol"
5 tristate "ARM System Control and Management Interface (SCMI) Message Protocol"
8 ARM System Control and Management Interface (SCMI) protocol is a
|
| /drivers/platform/x86/intel/uncore-frequency/ |
| D | Kconfig | 6 menu "Intel Uncore Frequency Control"
|
| /drivers/firmware/ |
| D | Kconfig | 12 tristate "ARM System Control and Power Interface (SCPI) Message Protocol"
16 System Control and Power Interface (SCPI) Message Protocol is
18 Cores(AP) and the System Control Processor(SCP). The MHU peripheral
262 tristate "TI System Control Interface (TISCI) Message Protocol"
265 TI System Control Interface (TISCI) Message Protocol is used to manage
|
| /drivers/reset/ |
| D | Kconfig | 195 Support for USBPHY Control found on RZ/G2L family. It mainly
259 tristate "TI System Control Interface (TI-SCI) reset driver"
262 This enables the reset driver support over TI System Control Interface
304 Say Y if you want to control reset signals provided by System Control
|
| /drivers/scsi/mpt3sas/mpi/ |
| D | mpi2_init.h | 122 U32 Control; /*0x3C */ member
274 U32 Control; /*0x3C */ member
|
| /drivers/media/cec/ |
| D | Kconfig | 31 Enable support for HDMI CEC (Consumer Electronics Control),
|
| /drivers/net/ethernet/freescale/dpaa2/ |
| D | Kconfig | 21 Enable Priority-Based Flow Control (PFC) support for DPAA2 Ethernet
|
| /drivers/message/fusion/lsi/ |
| D | mpi_init.h | 89 U32 Control; /* 14h */ member
276 U32 Control; /* 14h */ member
|
| D | mpi_raid.h | 187 U32 Control; /* 14h */ member
|
| D | mpi_history.txt | 79 * 08-19-04 01.05.01 Added defines for Host Buffer Access Control doorbell.
444 * Added Device Self Test to Control Flags of SAS IO Unit
720 * Control request, and added a new operation code.
722 * and Remove Device operations to SAS IO Unit Control.
723 * Added DevHandle field to SAS IO Unit Control request and
726 * Unit Control request.
729 * fields to SAS IO Unit Control Request.
|
| /drivers/peci/ |
| D | Kconfig | 6 The Platform Environment Control Interface (PECI) is an interface
|
| /drivers/usb/gadget/ |
| D | Kconfig | 257 bool "Abstract Control Model (CDC ACM)"
277 bool "Network Control Model (CDC NCM)"
289 bool "Ethernet Control Model (CDC ECM)"
295 The "Communication Device Class" (CDC) Ethernet Control Model.
301 bool "Ethernet Control Model (CDC ECM) subset"
|
| /drivers/usb/class/ |
| D | Kconfig | 12 Communication Device Class Abstract Control Model interface.
|
| /drivers/soc/fsl/ |
| D | Kconfig | 51 (Run Control and Power Management), which performs all device-level
|
| /drivers/net/ethernet/apple/ |
| D | Kconfig | 26 motherboard will usually use a MACE (Medium Access Control for
|
| /drivers/tty/vt/ |
| D | defkeymap.map | 75 keycode 29 = Control
224 keycode 97 = Control
|
| /drivers/soc/mediatek/ |
| D | Kconfig | 67 Control Processor System (SCPSYS) has several power management related
|