1 // SPDX-License-Identifier: GPL-1.0+
2 /*
3 * OHCI HCD (Host Controller Driver) for USB.
4 *
5 * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
6 * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
7 * (C) Copyright 2002 Hewlett-Packard Company
8 *
9 * Bus Glue for pxa27x
10 *
11 * Written by Christopher Hoover <ch@hpl.hp.com>
12 * Based on fragments of previous driver by Russell King et al.
13 *
14 * Modified for LH7A404 from ohci-sa1111.c
15 * by Durgesh Pattamatta <pattamattad@sharpsec.com>
16 *
17 * Modified for pxa27x from ohci-lh7a404.c
18 * by Nick Bane <nick@cecomputing.co.uk> 26-8-2004
19 *
20 * This file is licenced under the GPL.
21 */
22
23 #include <linux/clk.h>
24 #include <linux/device.h>
25 #include <linux/dma-mapping.h>
26 #include <linux/io.h>
27 #include <linux/kernel.h>
28 #include <linux/module.h>
29 #include <linux/of_platform.h>
30 #include <linux/of_gpio.h>
31 #include <linux/platform_data/usb-ohci-pxa27x.h>
32 #include <linux/platform_data/usb-pxa3xx-ulpi.h>
33 #include <linux/platform_device.h>
34 #include <linux/regulator/consumer.h>
35 #include <linux/signal.h>
36 #include <linux/usb.h>
37 #include <linux/usb/hcd.h>
38 #include <linux/usb/otg.h>
39 #include <linux/soc/pxa/cpu.h>
40
41 #include "ohci.h"
42
43 #define DRIVER_DESC "OHCI PXA27x/PXA3x driver"
44
45 /*
46 * UHC: USB Host Controller (OHCI-like) register definitions
47 */
48 #define UHCREV (0x0000) /* UHC HCI Spec Revision */
49 #define UHCHCON (0x0004) /* UHC Host Control Register */
50 #define UHCCOMS (0x0008) /* UHC Command Status Register */
51 #define UHCINTS (0x000C) /* UHC Interrupt Status Register */
52 #define UHCINTE (0x0010) /* UHC Interrupt Enable */
53 #define UHCINTD (0x0014) /* UHC Interrupt Disable */
54 #define UHCHCCA (0x0018) /* UHC Host Controller Comm. Area */
55 #define UHCPCED (0x001C) /* UHC Period Current Endpt Descr */
56 #define UHCCHED (0x0020) /* UHC Control Head Endpt Descr */
57 #define UHCCCED (0x0024) /* UHC Control Current Endpt Descr */
58 #define UHCBHED (0x0028) /* UHC Bulk Head Endpt Descr */
59 #define UHCBCED (0x002C) /* UHC Bulk Current Endpt Descr */
60 #define UHCDHEAD (0x0030) /* UHC Done Head */
61 #define UHCFMI (0x0034) /* UHC Frame Interval */
62 #define UHCFMR (0x0038) /* UHC Frame Remaining */
63 #define UHCFMN (0x003C) /* UHC Frame Number */
64 #define UHCPERS (0x0040) /* UHC Periodic Start */
65 #define UHCLS (0x0044) /* UHC Low Speed Threshold */
66
67 #define UHCRHDA (0x0048) /* UHC Root Hub Descriptor A */
68 #define UHCRHDA_NOCP (1 << 12) /* No over current protection */
69 #define UHCRHDA_OCPM (1 << 11) /* Over Current Protection Mode */
70 #define UHCRHDA_POTPGT(x) \
71 (((x) & 0xff) << 24) /* Power On To Power Good Time */
72
73 #define UHCRHDB (0x004C) /* UHC Root Hub Descriptor B */
74 #define UHCRHS (0x0050) /* UHC Root Hub Status */
75 #define UHCRHPS1 (0x0054) /* UHC Root Hub Port 1 Status */
76 #define UHCRHPS2 (0x0058) /* UHC Root Hub Port 2 Status */
77 #define UHCRHPS3 (0x005C) /* UHC Root Hub Port 3 Status */
78
79 #define UHCSTAT (0x0060) /* UHC Status Register */
80 #define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
81 #define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
82 #define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
83 #define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
84 #define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
85 #define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
86 #define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
87 #define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
88 #define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */
89
90 #define UHCHR (0x0064) /* UHC Reset Register */
91 #define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
92 #define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
93 #define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
94 #define UHCHR_PCPL (1 << 7) /* Power control polarity low */
95 #define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
96 #define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
97 #define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
98 #define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
99 #define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
100 #define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
101 #define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */
102
103 #define UHCHIE (0x0068) /* UHC Interrupt Enable Register*/
104 #define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
105 #define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
106 #define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
107 #define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
108 #define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
109 Interrupt Enable*/
110 #define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
111 #define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */
112
113 #define UHCHIT (0x006C) /* UHC Interrupt Test register */
114
115 #define PXA_UHC_MAX_PORTNUM 3
116
117 static struct hc_driver __read_mostly ohci_pxa27x_hc_driver;
118
119 struct pxa27x_ohci {
120 struct clk *clk;
121 void __iomem *mmio_base;
122 struct regulator *vbus[3];
123 bool vbus_enabled[3];
124 };
125
126 #define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
127
128 /*
129 PMM_NPS_MODE -- PMM Non-power switching mode
130 Ports are powered continuously.
131
132 PMM_GLOBAL_MODE -- PMM global switching mode
133 All ports are powered at the same time.
134
135 PMM_PERPORT_MODE -- PMM per port switching mode
136 Ports are powered individually.
137 */
pxa27x_ohci_select_pmm(struct pxa27x_ohci * pxa_ohci,int mode)138 static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *pxa_ohci, int mode)
139 {
140 uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
141 uint32_t uhcrhdb = __raw_readl(pxa_ohci->mmio_base + UHCRHDB);
142
143 switch (mode) {
144 case PMM_NPS_MODE:
145 uhcrhda |= RH_A_NPS;
146 break;
147 case PMM_GLOBAL_MODE:
148 uhcrhda &= ~(RH_A_NPS | RH_A_PSM);
149 break;
150 case PMM_PERPORT_MODE:
151 uhcrhda &= ~(RH_A_NPS);
152 uhcrhda |= RH_A_PSM;
153
154 /* Set port power control mask bits, only 3 ports. */
155 uhcrhdb |= (0x7<<17);
156 break;
157 default:
158 printk( KERN_ERR
159 "Invalid mode %d, set to non-power switch mode.\n",
160 mode );
161
162 uhcrhda |= RH_A_NPS;
163 }
164
165 __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
166 __raw_writel(uhcrhdb, pxa_ohci->mmio_base + UHCRHDB);
167 return 0;
168 }
169
pxa27x_ohci_set_vbus_power(struct pxa27x_ohci * pxa_ohci,unsigned int port,bool enable)170 static int pxa27x_ohci_set_vbus_power(struct pxa27x_ohci *pxa_ohci,
171 unsigned int port, bool enable)
172 {
173 struct regulator *vbus = pxa_ohci->vbus[port];
174 int ret = 0;
175
176 if (IS_ERR_OR_NULL(vbus))
177 return 0;
178
179 if (enable && !pxa_ohci->vbus_enabled[port])
180 ret = regulator_enable(vbus);
181 else if (!enable && pxa_ohci->vbus_enabled[port])
182 ret = regulator_disable(vbus);
183
184 if (ret < 0)
185 return ret;
186
187 pxa_ohci->vbus_enabled[port] = enable;
188
189 return 0;
190 }
191
pxa27x_ohci_hub_control(struct usb_hcd * hcd,u16 typeReq,u16 wValue,u16 wIndex,char * buf,u16 wLength)192 static int pxa27x_ohci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
193 u16 wIndex, char *buf, u16 wLength)
194 {
195 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
196 int ret;
197
198 switch (typeReq) {
199 case SetPortFeature:
200 case ClearPortFeature:
201 if (!wIndex || wIndex > 3)
202 return -EPIPE;
203
204 if (wValue != USB_PORT_FEAT_POWER)
205 break;
206
207 ret = pxa27x_ohci_set_vbus_power(pxa_ohci, wIndex - 1,
208 typeReq == SetPortFeature);
209 if (ret)
210 return ret;
211 break;
212 }
213
214 return ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
215 }
216 /*-------------------------------------------------------------------------*/
217
pxa27x_setup_hc(struct pxa27x_ohci * pxa_ohci,struct pxaohci_platform_data * inf)218 static inline void pxa27x_setup_hc(struct pxa27x_ohci *pxa_ohci,
219 struct pxaohci_platform_data *inf)
220 {
221 uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
222 uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
223
224 if (inf->flags & ENABLE_PORT1)
225 uhchr &= ~UHCHR_SSEP1;
226
227 if (inf->flags & ENABLE_PORT2)
228 uhchr &= ~UHCHR_SSEP2;
229
230 if (inf->flags & ENABLE_PORT3)
231 uhchr &= ~UHCHR_SSEP3;
232
233 if (inf->flags & POWER_CONTROL_LOW)
234 uhchr |= UHCHR_PCPL;
235
236 if (inf->flags & POWER_SENSE_LOW)
237 uhchr |= UHCHR_PSPL;
238
239 if (inf->flags & NO_OC_PROTECTION)
240 uhcrhda |= UHCRHDA_NOCP;
241 else
242 uhcrhda &= ~UHCRHDA_NOCP;
243
244 if (inf->flags & OC_MODE_PERPORT)
245 uhcrhda |= UHCRHDA_OCPM;
246 else
247 uhcrhda &= ~UHCRHDA_OCPM;
248
249 if (inf->power_on_delay) {
250 uhcrhda &= ~UHCRHDA_POTPGT(0xff);
251 uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2);
252 }
253
254 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
255 __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
256 }
257
pxa27x_reset_hc(struct pxa27x_ohci * pxa_ohci)258 static inline void pxa27x_reset_hc(struct pxa27x_ohci *pxa_ohci)
259 {
260 uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
261
262 __raw_writel(uhchr | UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
263 udelay(11);
264 __raw_writel(uhchr & ~UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
265 }
266
267 #ifdef CONFIG_PXA27x
268 extern void pxa27x_clear_otgph(void);
269 #else
270 #define pxa27x_clear_otgph() do {} while (0)
271 #endif
272
pxa27x_start_hc(struct pxa27x_ohci * pxa_ohci,struct device * dev)273 static int pxa27x_start_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
274 {
275 int retval;
276 struct pxaohci_platform_data *inf;
277 uint32_t uhchr;
278 struct usb_hcd *hcd = dev_get_drvdata(dev);
279
280 inf = dev_get_platdata(dev);
281
282 retval = clk_prepare_enable(pxa_ohci->clk);
283 if (retval)
284 return retval;
285
286 pxa27x_reset_hc(pxa_ohci);
287
288 uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
289 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
290
291 while (__raw_readl(pxa_ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
292 cpu_relax();
293
294 pxa27x_setup_hc(pxa_ohci, inf);
295
296 if (inf->init)
297 retval = inf->init(dev);
298
299 if (retval < 0) {
300 clk_disable_unprepare(pxa_ohci->clk);
301 return retval;
302 }
303
304 if (cpu_is_pxa3xx())
305 pxa3xx_u2d_start_hc(&hcd->self);
306
307 uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
308 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
309 __raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, pxa_ohci->mmio_base + UHCHIE);
310
311 /* Clear any OTG Pin Hold */
312 pxa27x_clear_otgph();
313 return 0;
314 }
315
pxa27x_stop_hc(struct pxa27x_ohci * pxa_ohci,struct device * dev)316 static void pxa27x_stop_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
317 {
318 struct pxaohci_platform_data *inf;
319 struct usb_hcd *hcd = dev_get_drvdata(dev);
320 uint32_t uhccoms;
321
322 inf = dev_get_platdata(dev);
323
324 if (cpu_is_pxa3xx())
325 pxa3xx_u2d_stop_hc(&hcd->self);
326
327 if (inf->exit)
328 inf->exit(dev);
329
330 pxa27x_reset_hc(pxa_ohci);
331
332 /* Host Controller Reset */
333 uhccoms = __raw_readl(pxa_ohci->mmio_base + UHCCOMS) | 0x01;
334 __raw_writel(uhccoms, pxa_ohci->mmio_base + UHCCOMS);
335 udelay(10);
336
337 clk_disable_unprepare(pxa_ohci->clk);
338 }
339
340 #ifdef CONFIG_OF
341 static const struct of_device_id pxa_ohci_dt_ids[] = {
342 { .compatible = "marvell,pxa-ohci" },
343 { }
344 };
345
346 MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids);
347
ohci_pxa_of_init(struct platform_device * pdev)348 static int ohci_pxa_of_init(struct platform_device *pdev)
349 {
350 struct device_node *np = pdev->dev.of_node;
351 struct pxaohci_platform_data *pdata;
352 u32 tmp;
353 int ret;
354
355 if (!np)
356 return 0;
357
358 /* Right now device-tree probed devices don't get dma_mask set.
359 * Since shared usb code relies on it, set it here for now.
360 * Once we have dma capability bindings this can go away.
361 */
362 ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
363 if (ret)
364 return ret;
365
366 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
367 if (!pdata)
368 return -ENOMEM;
369
370 if (of_property_read_bool(np, "marvell,enable-port1"))
371 pdata->flags |= ENABLE_PORT1;
372 if (of_property_read_bool(np, "marvell,enable-port2"))
373 pdata->flags |= ENABLE_PORT2;
374 if (of_property_read_bool(np, "marvell,enable-port3"))
375 pdata->flags |= ENABLE_PORT3;
376 if (of_property_read_bool(np, "marvell,port-sense-low"))
377 pdata->flags |= POWER_SENSE_LOW;
378 if (of_property_read_bool(np, "marvell,power-control-low"))
379 pdata->flags |= POWER_CONTROL_LOW;
380 if (of_property_read_bool(np, "marvell,no-oc-protection"))
381 pdata->flags |= NO_OC_PROTECTION;
382 if (of_property_read_bool(np, "marvell,oc-mode-perport"))
383 pdata->flags |= OC_MODE_PERPORT;
384 if (!of_property_read_u32(np, "marvell,power-on-delay", &tmp))
385 pdata->power_on_delay = tmp;
386 if (!of_property_read_u32(np, "marvell,port-mode", &tmp))
387 pdata->port_mode = tmp;
388 if (!of_property_read_u32(np, "marvell,power-budget", &tmp))
389 pdata->power_budget = tmp;
390
391 pdev->dev.platform_data = pdata;
392
393 return 0;
394 }
395 #else
ohci_pxa_of_init(struct platform_device * pdev)396 static int ohci_pxa_of_init(struct platform_device *pdev)
397 {
398 return 0;
399 }
400 #endif
401
402 /*-------------------------------------------------------------------------*/
403
404 /* configure so an HC device and id are always provided */
405 /* always called with process context; sleeping is OK */
406
407
408 /**
409 * ohci_hcd_pxa27x_probe - initialize pxa27x-based HCDs
410 * @pdev: USB Host controller to probe
411 *
412 * Context: task context, might sleep
413 *
414 * Allocates basic resources for this USB host controller, and
415 * then invokes the start() method for the HCD associated with it
416 * through the hotplug entry's driver_data.
417 */
ohci_hcd_pxa27x_probe(struct platform_device * pdev)418 static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
419 {
420 int retval, irq;
421 struct usb_hcd *hcd;
422 struct pxaohci_platform_data *inf;
423 struct pxa27x_ohci *pxa_ohci;
424 struct ohci_hcd *ohci;
425 struct resource *r;
426 struct clk *usb_clk;
427 unsigned int i;
428
429 retval = ohci_pxa_of_init(pdev);
430 if (retval)
431 return retval;
432
433 inf = dev_get_platdata(&pdev->dev);
434
435 if (!inf)
436 return -ENODEV;
437
438 irq = platform_get_irq(pdev, 0);
439 if (irq < 0) {
440 pr_err("no resource of IORESOURCE_IRQ");
441 return irq;
442 }
443
444 usb_clk = devm_clk_get(&pdev->dev, NULL);
445 if (IS_ERR(usb_clk))
446 return PTR_ERR(usb_clk);
447
448 hcd = usb_create_hcd(&ohci_pxa27x_hc_driver, &pdev->dev, "pxa27x");
449 if (!hcd)
450 return -ENOMEM;
451
452 r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
453 hcd->regs = devm_ioremap_resource(&pdev->dev, r);
454 if (IS_ERR(hcd->regs)) {
455 retval = PTR_ERR(hcd->regs);
456 goto err;
457 }
458 hcd->rsrc_start = r->start;
459 hcd->rsrc_len = resource_size(r);
460
461 /* initialize "struct pxa27x_ohci" */
462 pxa_ohci = to_pxa27x_ohci(hcd);
463 pxa_ohci->clk = usb_clk;
464 pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
465
466 for (i = 0; i < 3; ++i) {
467 char name[6];
468
469 if (!(inf->flags & (ENABLE_PORT1 << i)))
470 continue;
471
472 sprintf(name, "vbus%u", i + 1);
473 pxa_ohci->vbus[i] = devm_regulator_get(&pdev->dev, name);
474 }
475
476 retval = pxa27x_start_hc(pxa_ohci, &pdev->dev);
477 if (retval < 0) {
478 pr_debug("pxa27x_start_hc failed");
479 goto err;
480 }
481
482 /* Select Power Management Mode */
483 pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
484
485 if (inf->power_budget)
486 hcd->power_budget = inf->power_budget;
487
488 /* The value of NDP in roothub_a is incorrect on this hardware */
489 ohci = hcd_to_ohci(hcd);
490 ohci->num_ports = 3;
491
492 retval = usb_add_hcd(hcd, irq, 0);
493 if (retval == 0) {
494 device_wakeup_enable(hcd->self.controller);
495 return retval;
496 }
497
498 pxa27x_stop_hc(pxa_ohci, &pdev->dev);
499 err:
500 usb_put_hcd(hcd);
501 return retval;
502 }
503
504
505 /* may be called without controller electrically present */
506 /* may be called with controller, bus, and devices active */
507
508 /**
509 * ohci_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs
510 * @pdev: USB Host Controller being removed
511 *
512 * Context: task context, might sleep
513 *
514 * Reverses the effect of ohci_hcd_pxa27x_probe(), first invoking
515 * the HCD's stop() method. It is always called from a thread
516 * context, normally "rmmod", "apmd", or something similar.
517 */
ohci_hcd_pxa27x_remove(struct platform_device * pdev)518 static int ohci_hcd_pxa27x_remove(struct platform_device *pdev)
519 {
520 struct usb_hcd *hcd = platform_get_drvdata(pdev);
521 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
522 unsigned int i;
523
524 usb_remove_hcd(hcd);
525 pxa27x_stop_hc(pxa_ohci, &pdev->dev);
526
527 for (i = 0; i < 3; ++i)
528 pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);
529
530 usb_put_hcd(hcd);
531 return 0;
532 }
533
534 /*-------------------------------------------------------------------------*/
535
536 #ifdef CONFIG_PM
ohci_hcd_pxa27x_drv_suspend(struct device * dev)537 static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
538 {
539 struct usb_hcd *hcd = dev_get_drvdata(dev);
540 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
541 struct ohci_hcd *ohci = hcd_to_ohci(hcd);
542 bool do_wakeup = device_may_wakeup(dev);
543 int ret;
544
545
546 if (time_before(jiffies, ohci->next_statechange))
547 msleep(5);
548 ohci->next_statechange = jiffies;
549
550 ret = ohci_suspend(hcd, do_wakeup);
551 if (ret)
552 return ret;
553
554 pxa27x_stop_hc(pxa_ohci, dev);
555 return ret;
556 }
557
ohci_hcd_pxa27x_drv_resume(struct device * dev)558 static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
559 {
560 struct usb_hcd *hcd = dev_get_drvdata(dev);
561 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
562 struct pxaohci_platform_data *inf = dev_get_platdata(dev);
563 struct ohci_hcd *ohci = hcd_to_ohci(hcd);
564 int status;
565
566 if (time_before(jiffies, ohci->next_statechange))
567 msleep(5);
568 ohci->next_statechange = jiffies;
569
570 status = pxa27x_start_hc(pxa_ohci, dev);
571 if (status < 0)
572 return status;
573
574 /* Select Power Management Mode */
575 pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
576
577 ohci_resume(hcd, false);
578 return 0;
579 }
580
581 static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
582 .suspend = ohci_hcd_pxa27x_drv_suspend,
583 .resume = ohci_hcd_pxa27x_drv_resume,
584 };
585 #endif
586
587 static struct platform_driver ohci_hcd_pxa27x_driver = {
588 .probe = ohci_hcd_pxa27x_probe,
589 .remove = ohci_hcd_pxa27x_remove,
590 .shutdown = usb_hcd_platform_shutdown,
591 .driver = {
592 .name = "pxa27x-ohci",
593 .of_match_table = of_match_ptr(pxa_ohci_dt_ids),
594 #ifdef CONFIG_PM
595 .pm = &ohci_hcd_pxa27x_pm_ops,
596 #endif
597 },
598 };
599
600 static const struct ohci_driver_overrides pxa27x_overrides __initconst = {
601 .extra_priv_size = sizeof(struct pxa27x_ohci),
602 };
603
ohci_pxa27x_init(void)604 static int __init ohci_pxa27x_init(void)
605 {
606 if (usb_disabled())
607 return -ENODEV;
608
609 ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides);
610 ohci_pxa27x_hc_driver.hub_control = pxa27x_ohci_hub_control;
611
612 return platform_driver_register(&ohci_hcd_pxa27x_driver);
613 }
614 module_init(ohci_pxa27x_init);
615
ohci_pxa27x_cleanup(void)616 static void __exit ohci_pxa27x_cleanup(void)
617 {
618 platform_driver_unregister(&ohci_hcd_pxa27x_driver);
619 }
620 module_exit(ohci_pxa27x_cleanup);
621
622 MODULE_DESCRIPTION(DRIVER_DESC);
623 MODULE_LICENSE("GPL");
624 MODULE_ALIAS("platform:pxa27x-ohci");
625