1 // SPDX-License-Identifier: GPL-2.0-only
2 // Copyright (C) 2013 Broadcom Corporation
3
4 #include <linux/device.h>
5 #include <linux/kernel.h>
6 #include <linux/module.h>
7 #include <linux/sched.h>
8 #include <linux/i2c.h>
9 #include <linux/interrupt.h>
10 #include <linux/platform_device.h>
11 #include <linux/clk.h>
12 #include <linux/io.h>
13 #include <linux/slab.h>
14
15 /* Hardware register offsets and field defintions */
16 #define CS_OFFSET 0x00000020
17 #define CS_ACK_SHIFT 3
18 #define CS_ACK_MASK 0x00000008
19 #define CS_ACK_CMD_GEN_START 0x00000000
20 #define CS_ACK_CMD_GEN_RESTART 0x00000001
21 #define CS_CMD_SHIFT 1
22 #define CS_CMD_CMD_NO_ACTION 0x00000000
23 #define CS_CMD_CMD_START_RESTART 0x00000001
24 #define CS_CMD_CMD_STOP 0x00000002
25 #define CS_EN_SHIFT 0
26 #define CS_EN_CMD_ENABLE_BSC 0x00000001
27
28 #define TIM_OFFSET 0x00000024
29 #define TIM_PRESCALE_SHIFT 6
30 #define TIM_P_SHIFT 3
31 #define TIM_NO_DIV_SHIFT 2
32 #define TIM_DIV_SHIFT 0
33
34 #define DAT_OFFSET 0x00000028
35
36 #define TOUT_OFFSET 0x0000002c
37
38 #define TXFCR_OFFSET 0x0000003c
39 #define TXFCR_FIFO_FLUSH_MASK 0x00000080
40 #define TXFCR_FIFO_EN_MASK 0x00000040
41
42 #define IER_OFFSET 0x00000044
43 #define IER_READ_COMPLETE_INT_MASK 0x00000010
44 #define IER_I2C_INT_EN_MASK 0x00000008
45 #define IER_FIFO_INT_EN_MASK 0x00000002
46 #define IER_NOACK_EN_MASK 0x00000001
47
48 #define ISR_OFFSET 0x00000048
49 #define ISR_RESERVED_MASK 0xffffff60
50 #define ISR_CMDBUSY_MASK 0x00000080
51 #define ISR_READ_COMPLETE_MASK 0x00000010
52 #define ISR_SES_DONE_MASK 0x00000008
53 #define ISR_ERR_MASK 0x00000004
54 #define ISR_TXFIFOEMPTY_MASK 0x00000002
55 #define ISR_NOACK_MASK 0x00000001
56
57 #define CLKEN_OFFSET 0x0000004C
58 #define CLKEN_AUTOSENSE_OFF_MASK 0x00000080
59 #define CLKEN_M_SHIFT 4
60 #define CLKEN_N_SHIFT 1
61 #define CLKEN_CLKEN_MASK 0x00000001
62
63 #define FIFO_STATUS_OFFSET 0x00000054
64 #define FIFO_STATUS_RXFIFO_EMPTY_MASK 0x00000004
65 #define FIFO_STATUS_TXFIFO_EMPTY_MASK 0x00000010
66
67 #define HSTIM_OFFSET 0x00000058
68 #define HSTIM_HS_MODE_MASK 0x00008000
69 #define HSTIM_HS_HOLD_SHIFT 10
70 #define HSTIM_HS_HIGH_PHASE_SHIFT 5
71 #define HSTIM_HS_SETUP_SHIFT 0
72
73 #define PADCTL_OFFSET 0x0000005c
74 #define PADCTL_PAD_OUT_EN_MASK 0x00000004
75
76 #define RXFCR_OFFSET 0x00000068
77 #define RXFCR_NACK_EN_SHIFT 7
78 #define RXFCR_READ_COUNT_SHIFT 0
79 #define RXFIFORDOUT_OFFSET 0x0000006c
80
81 /* Locally used constants */
82 #define MAX_RX_FIFO_SIZE 64U /* bytes */
83 #define MAX_TX_FIFO_SIZE 64U /* bytes */
84
85 #define STD_EXT_CLK_FREQ 13000000UL
86 #define HS_EXT_CLK_FREQ 104000000UL
87
88 #define MASTERCODE 0x08 /* Mastercodes are 0000_1xxxb */
89
90 #define I2C_TIMEOUT 100 /* msecs */
91
92 /* Operations that can be commanded to the controller */
93 enum bcm_kona_cmd_t {
94 BCM_CMD_NOACTION = 0,
95 BCM_CMD_START,
96 BCM_CMD_RESTART,
97 BCM_CMD_STOP,
98 };
99
100 enum bus_speed_index {
101 BCM_SPD_100K = 0,
102 BCM_SPD_400K,
103 BCM_SPD_1MHZ,
104 };
105
106 enum hs_bus_speed_index {
107 BCM_SPD_3P4MHZ = 0,
108 };
109
110 /* Internal divider settings for standard mode, fast mode and fast mode plus */
111 struct bus_speed_cfg {
112 uint8_t time_m; /* Number of cycles for setup time */
113 uint8_t time_n; /* Number of cycles for hold time */
114 uint8_t prescale; /* Prescale divider */
115 uint8_t time_p; /* Timing coefficient */
116 uint8_t no_div; /* Disable clock divider */
117 uint8_t time_div; /* Post-prescale divider */
118 };
119
120 /* Internal divider settings for high-speed mode */
121 struct hs_bus_speed_cfg {
122 uint8_t hs_hold; /* Number of clock cycles SCL stays low until
123 the end of bit period */
124 uint8_t hs_high_phase; /* Number of clock cycles SCL stays high
125 before it falls */
126 uint8_t hs_setup; /* Number of clock cycles SCL stays low
127 before it rises */
128 uint8_t prescale; /* Prescale divider */
129 uint8_t time_p; /* Timing coefficient */
130 uint8_t no_div; /* Disable clock divider */
131 uint8_t time_div; /* Post-prescale divider */
132 };
133
134 static const struct bus_speed_cfg std_cfg_table[] = {
135 [BCM_SPD_100K] = {0x01, 0x01, 0x03, 0x06, 0x00, 0x02},
136 [BCM_SPD_400K] = {0x05, 0x01, 0x03, 0x05, 0x01, 0x02},
137 [BCM_SPD_1MHZ] = {0x01, 0x01, 0x03, 0x01, 0x01, 0x03},
138 };
139
140 static const struct hs_bus_speed_cfg hs_cfg_table[] = {
141 [BCM_SPD_3P4MHZ] = {0x01, 0x08, 0x14, 0x00, 0x06, 0x01, 0x00},
142 };
143
144 struct bcm_kona_i2c_dev {
145 struct device *device;
146
147 void __iomem *base;
148 int irq;
149 struct clk *external_clk;
150
151 struct i2c_adapter adapter;
152
153 struct completion done;
154
155 const struct bus_speed_cfg *std_cfg;
156 const struct hs_bus_speed_cfg *hs_cfg;
157 };
158
bcm_kona_i2c_send_cmd_to_ctrl(struct bcm_kona_i2c_dev * dev,enum bcm_kona_cmd_t cmd)159 static void bcm_kona_i2c_send_cmd_to_ctrl(struct bcm_kona_i2c_dev *dev,
160 enum bcm_kona_cmd_t cmd)
161 {
162 dev_dbg(dev->device, "%s, %d\n", __func__, cmd);
163
164 switch (cmd) {
165 case BCM_CMD_NOACTION:
166 writel((CS_CMD_CMD_NO_ACTION << CS_CMD_SHIFT) |
167 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
168 dev->base + CS_OFFSET);
169 break;
170
171 case BCM_CMD_START:
172 writel((CS_ACK_CMD_GEN_START << CS_ACK_SHIFT) |
173 (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) |
174 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
175 dev->base + CS_OFFSET);
176 break;
177
178 case BCM_CMD_RESTART:
179 writel((CS_ACK_CMD_GEN_RESTART << CS_ACK_SHIFT) |
180 (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) |
181 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
182 dev->base + CS_OFFSET);
183 break;
184
185 case BCM_CMD_STOP:
186 writel((CS_CMD_CMD_STOP << CS_CMD_SHIFT) |
187 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
188 dev->base + CS_OFFSET);
189 break;
190
191 default:
192 dev_err(dev->device, "Unknown command %d\n", cmd);
193 }
194 }
195
bcm_kona_i2c_enable_clock(struct bcm_kona_i2c_dev * dev)196 static void bcm_kona_i2c_enable_clock(struct bcm_kona_i2c_dev *dev)
197 {
198 writel(readl(dev->base + CLKEN_OFFSET) | CLKEN_CLKEN_MASK,
199 dev->base + CLKEN_OFFSET);
200 }
201
bcm_kona_i2c_disable_clock(struct bcm_kona_i2c_dev * dev)202 static void bcm_kona_i2c_disable_clock(struct bcm_kona_i2c_dev *dev)
203 {
204 writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_CLKEN_MASK,
205 dev->base + CLKEN_OFFSET);
206 }
207
bcm_kona_i2c_isr(int irq,void * devid)208 static irqreturn_t bcm_kona_i2c_isr(int irq, void *devid)
209 {
210 struct bcm_kona_i2c_dev *dev = devid;
211 uint32_t status = readl(dev->base + ISR_OFFSET);
212
213 if ((status & ~ISR_RESERVED_MASK) == 0)
214 return IRQ_NONE;
215
216 /* Must flush the TX FIFO when NAK detected */
217 if (status & ISR_NOACK_MASK)
218 writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK,
219 dev->base + TXFCR_OFFSET);
220
221 writel(status & ~ISR_RESERVED_MASK, dev->base + ISR_OFFSET);
222 complete(&dev->done);
223
224 return IRQ_HANDLED;
225 }
226
227 /* Wait for ISR_CMDBUSY_MASK to go low before writing to CS, DAT, or RCD */
bcm_kona_i2c_wait_if_busy(struct bcm_kona_i2c_dev * dev)228 static int bcm_kona_i2c_wait_if_busy(struct bcm_kona_i2c_dev *dev)
229 {
230 unsigned long timeout = jiffies + msecs_to_jiffies(I2C_TIMEOUT);
231
232 while (readl(dev->base + ISR_OFFSET) & ISR_CMDBUSY_MASK)
233 if (time_after(jiffies, timeout)) {
234 dev_err(dev->device, "CMDBUSY timeout\n");
235 return -ETIMEDOUT;
236 }
237
238 return 0;
239 }
240
241 /* Send command to I2C bus */
bcm_kona_send_i2c_cmd(struct bcm_kona_i2c_dev * dev,enum bcm_kona_cmd_t cmd)242 static int bcm_kona_send_i2c_cmd(struct bcm_kona_i2c_dev *dev,
243 enum bcm_kona_cmd_t cmd)
244 {
245 int rc;
246 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT);
247
248 /* Make sure the hardware is ready */
249 rc = bcm_kona_i2c_wait_if_busy(dev);
250 if (rc < 0)
251 return rc;
252
253 /* Unmask the session done interrupt */
254 writel(IER_I2C_INT_EN_MASK, dev->base + IER_OFFSET);
255
256 /* Mark as incomplete before sending the command */
257 reinit_completion(&dev->done);
258
259 /* Send the command */
260 bcm_kona_i2c_send_cmd_to_ctrl(dev, cmd);
261
262 /* Wait for transaction to finish or timeout */
263 time_left = wait_for_completion_timeout(&dev->done, time_left);
264
265 /* Mask all interrupts */
266 writel(0, dev->base + IER_OFFSET);
267
268 if (!time_left) {
269 dev_err(dev->device, "controller timed out\n");
270 rc = -ETIMEDOUT;
271 }
272
273 /* Clear command */
274 bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION);
275
276 return rc;
277 }
278
279 /* Read a single RX FIFO worth of data from the i2c bus */
bcm_kona_i2c_read_fifo_single(struct bcm_kona_i2c_dev * dev,uint8_t * buf,unsigned int len,unsigned int last_byte_nak)280 static int bcm_kona_i2c_read_fifo_single(struct bcm_kona_i2c_dev *dev,
281 uint8_t *buf, unsigned int len,
282 unsigned int last_byte_nak)
283 {
284 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT);
285
286 /* Mark as incomplete before starting the RX FIFO */
287 reinit_completion(&dev->done);
288
289 /* Unmask the read complete interrupt */
290 writel(IER_READ_COMPLETE_INT_MASK, dev->base + IER_OFFSET);
291
292 /* Start the RX FIFO */
293 writel((last_byte_nak << RXFCR_NACK_EN_SHIFT) |
294 (len << RXFCR_READ_COUNT_SHIFT),
295 dev->base + RXFCR_OFFSET);
296
297 /* Wait for FIFO read to complete */
298 time_left = wait_for_completion_timeout(&dev->done, time_left);
299
300 /* Mask all interrupts */
301 writel(0, dev->base + IER_OFFSET);
302
303 if (!time_left) {
304 dev_err(dev->device, "RX FIFO time out\n");
305 return -EREMOTEIO;
306 }
307
308 /* Read data from FIFO */
309 for (; len > 0; len--, buf++)
310 *buf = readl(dev->base + RXFIFORDOUT_OFFSET);
311
312 return 0;
313 }
314
315 /* Read any amount of data using the RX FIFO from the i2c bus */
bcm_kona_i2c_read_fifo(struct bcm_kona_i2c_dev * dev,struct i2c_msg * msg)316 static int bcm_kona_i2c_read_fifo(struct bcm_kona_i2c_dev *dev,
317 struct i2c_msg *msg)
318 {
319 unsigned int bytes_to_read = MAX_RX_FIFO_SIZE;
320 unsigned int last_byte_nak = 0;
321 unsigned int bytes_read = 0;
322 int rc;
323
324 uint8_t *tmp_buf = msg->buf;
325
326 while (bytes_read < msg->len) {
327 if (msg->len - bytes_read <= MAX_RX_FIFO_SIZE) {
328 last_byte_nak = 1; /* NAK last byte of transfer */
329 bytes_to_read = msg->len - bytes_read;
330 }
331
332 rc = bcm_kona_i2c_read_fifo_single(dev, tmp_buf, bytes_to_read,
333 last_byte_nak);
334 if (rc < 0)
335 return -EREMOTEIO;
336
337 bytes_read += bytes_to_read;
338 tmp_buf += bytes_to_read;
339 }
340
341 return 0;
342 }
343
344 /* Write a single byte of data to the i2c bus */
bcm_kona_i2c_write_byte(struct bcm_kona_i2c_dev * dev,uint8_t data,unsigned int nak_expected)345 static int bcm_kona_i2c_write_byte(struct bcm_kona_i2c_dev *dev, uint8_t data,
346 unsigned int nak_expected)
347 {
348 int rc;
349 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT);
350 unsigned int nak_received;
351
352 /* Make sure the hardware is ready */
353 rc = bcm_kona_i2c_wait_if_busy(dev);
354 if (rc < 0)
355 return rc;
356
357 /* Clear pending session done interrupt */
358 writel(ISR_SES_DONE_MASK, dev->base + ISR_OFFSET);
359
360 /* Unmask the session done interrupt */
361 writel(IER_I2C_INT_EN_MASK, dev->base + IER_OFFSET);
362
363 /* Mark as incomplete before sending the data */
364 reinit_completion(&dev->done);
365
366 /* Send one byte of data */
367 writel(data, dev->base + DAT_OFFSET);
368
369 /* Wait for byte to be written */
370 time_left = wait_for_completion_timeout(&dev->done, time_left);
371
372 /* Mask all interrupts */
373 writel(0, dev->base + IER_OFFSET);
374
375 if (!time_left) {
376 dev_dbg(dev->device, "controller timed out\n");
377 return -ETIMEDOUT;
378 }
379
380 nak_received = readl(dev->base + CS_OFFSET) & CS_ACK_MASK ? 1 : 0;
381
382 if (nak_received ^ nak_expected) {
383 dev_dbg(dev->device, "unexpected NAK/ACK\n");
384 return -EREMOTEIO;
385 }
386
387 return 0;
388 }
389
390 /* Write a single TX FIFO worth of data to the i2c bus */
bcm_kona_i2c_write_fifo_single(struct bcm_kona_i2c_dev * dev,uint8_t * buf,unsigned int len)391 static int bcm_kona_i2c_write_fifo_single(struct bcm_kona_i2c_dev *dev,
392 uint8_t *buf, unsigned int len)
393 {
394 int k;
395 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT);
396 unsigned int fifo_status;
397
398 /* Mark as incomplete before sending data to the TX FIFO */
399 reinit_completion(&dev->done);
400
401 /* Unmask the fifo empty and nak interrupt */
402 writel(IER_FIFO_INT_EN_MASK | IER_NOACK_EN_MASK,
403 dev->base + IER_OFFSET);
404
405 /* Disable IRQ to load a FIFO worth of data without interruption */
406 disable_irq(dev->irq);
407
408 /* Write data into FIFO */
409 for (k = 0; k < len; k++)
410 writel(buf[k], (dev->base + DAT_OFFSET));
411
412 /* Enable IRQ now that data has been loaded */
413 enable_irq(dev->irq);
414
415 /* Wait for FIFO to empty */
416 do {
417 time_left = wait_for_completion_timeout(&dev->done, time_left);
418 fifo_status = readl(dev->base + FIFO_STATUS_OFFSET);
419 } while (time_left && !(fifo_status & FIFO_STATUS_TXFIFO_EMPTY_MASK));
420
421 /* Mask all interrupts */
422 writel(0, dev->base + IER_OFFSET);
423
424 /* Check if there was a NAK */
425 if (readl(dev->base + CS_OFFSET) & CS_ACK_MASK) {
426 dev_err(dev->device, "unexpected NAK\n");
427 return -EREMOTEIO;
428 }
429
430 /* Check if a timeout occured */
431 if (!time_left) {
432 dev_err(dev->device, "completion timed out\n");
433 return -EREMOTEIO;
434 }
435
436 return 0;
437 }
438
439
440 /* Write any amount of data using TX FIFO to the i2c bus */
bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev * dev,struct i2c_msg * msg)441 static int bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev *dev,
442 struct i2c_msg *msg)
443 {
444 unsigned int bytes_to_write = MAX_TX_FIFO_SIZE;
445 unsigned int bytes_written = 0;
446 int rc;
447
448 uint8_t *tmp_buf = msg->buf;
449
450 while (bytes_written < msg->len) {
451 if (msg->len - bytes_written <= MAX_TX_FIFO_SIZE)
452 bytes_to_write = msg->len - bytes_written;
453
454 rc = bcm_kona_i2c_write_fifo_single(dev, tmp_buf,
455 bytes_to_write);
456 if (rc < 0)
457 return -EREMOTEIO;
458
459 bytes_written += bytes_to_write;
460 tmp_buf += bytes_to_write;
461 }
462
463 return 0;
464 }
465
466 /* Send i2c address */
bcm_kona_i2c_do_addr(struct bcm_kona_i2c_dev * dev,struct i2c_msg * msg)467 static int bcm_kona_i2c_do_addr(struct bcm_kona_i2c_dev *dev,
468 struct i2c_msg *msg)
469 {
470 unsigned char addr;
471
472 if (msg->flags & I2C_M_TEN) {
473 /* First byte is 11110XX0 where XX is upper 2 bits */
474 addr = 0xF0 | ((msg->addr & 0x300) >> 7);
475 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
476 return -EREMOTEIO;
477
478 /* Second byte is the remaining 8 bits */
479 addr = msg->addr & 0xFF;
480 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
481 return -EREMOTEIO;
482
483 if (msg->flags & I2C_M_RD) {
484 /* For read, send restart command */
485 if (bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART) < 0)
486 return -EREMOTEIO;
487
488 /* Then re-send the first byte with the read bit set */
489 addr = 0xF0 | ((msg->addr & 0x300) >> 7) | 0x01;
490 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
491 return -EREMOTEIO;
492 }
493 } else {
494 addr = i2c_8bit_addr_from_msg(msg);
495
496 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
497 return -EREMOTEIO;
498 }
499
500 return 0;
501 }
502
bcm_kona_i2c_enable_autosense(struct bcm_kona_i2c_dev * dev)503 static void bcm_kona_i2c_enable_autosense(struct bcm_kona_i2c_dev *dev)
504 {
505 writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_AUTOSENSE_OFF_MASK,
506 dev->base + CLKEN_OFFSET);
507 }
508
bcm_kona_i2c_config_timing(struct bcm_kona_i2c_dev * dev)509 static void bcm_kona_i2c_config_timing(struct bcm_kona_i2c_dev *dev)
510 {
511 writel(readl(dev->base + HSTIM_OFFSET) & ~HSTIM_HS_MODE_MASK,
512 dev->base + HSTIM_OFFSET);
513
514 writel((dev->std_cfg->prescale << TIM_PRESCALE_SHIFT) |
515 (dev->std_cfg->time_p << TIM_P_SHIFT) |
516 (dev->std_cfg->no_div << TIM_NO_DIV_SHIFT) |
517 (dev->std_cfg->time_div << TIM_DIV_SHIFT),
518 dev->base + TIM_OFFSET);
519
520 writel((dev->std_cfg->time_m << CLKEN_M_SHIFT) |
521 (dev->std_cfg->time_n << CLKEN_N_SHIFT) |
522 CLKEN_CLKEN_MASK,
523 dev->base + CLKEN_OFFSET);
524 }
525
bcm_kona_i2c_config_timing_hs(struct bcm_kona_i2c_dev * dev)526 static void bcm_kona_i2c_config_timing_hs(struct bcm_kona_i2c_dev *dev)
527 {
528 writel((dev->hs_cfg->prescale << TIM_PRESCALE_SHIFT) |
529 (dev->hs_cfg->time_p << TIM_P_SHIFT) |
530 (dev->hs_cfg->no_div << TIM_NO_DIV_SHIFT) |
531 (dev->hs_cfg->time_div << TIM_DIV_SHIFT),
532 dev->base + TIM_OFFSET);
533
534 writel((dev->hs_cfg->hs_hold << HSTIM_HS_HOLD_SHIFT) |
535 (dev->hs_cfg->hs_high_phase << HSTIM_HS_HIGH_PHASE_SHIFT) |
536 (dev->hs_cfg->hs_setup << HSTIM_HS_SETUP_SHIFT),
537 dev->base + HSTIM_OFFSET);
538
539 writel(readl(dev->base + HSTIM_OFFSET) | HSTIM_HS_MODE_MASK,
540 dev->base + HSTIM_OFFSET);
541 }
542
bcm_kona_i2c_switch_to_hs(struct bcm_kona_i2c_dev * dev)543 static int bcm_kona_i2c_switch_to_hs(struct bcm_kona_i2c_dev *dev)
544 {
545 int rc;
546
547 /* Send mastercode at standard speed */
548 rc = bcm_kona_i2c_write_byte(dev, MASTERCODE, 1);
549 if (rc < 0) {
550 pr_err("High speed handshake failed\n");
551 return rc;
552 }
553
554 /* Configure external clock to higher frequency */
555 rc = clk_set_rate(dev->external_clk, HS_EXT_CLK_FREQ);
556 if (rc) {
557 dev_err(dev->device, "%s: clk_set_rate returned %d\n",
558 __func__, rc);
559 return rc;
560 }
561
562 /* Reconfigure internal dividers */
563 bcm_kona_i2c_config_timing_hs(dev);
564
565 /* Send a restart command */
566 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART);
567 if (rc < 0)
568 dev_err(dev->device, "High speed restart command failed\n");
569
570 return rc;
571 }
572
bcm_kona_i2c_switch_to_std(struct bcm_kona_i2c_dev * dev)573 static int bcm_kona_i2c_switch_to_std(struct bcm_kona_i2c_dev *dev)
574 {
575 int rc;
576
577 /* Reconfigure internal dividers */
578 bcm_kona_i2c_config_timing(dev);
579
580 /* Configure external clock to lower frequency */
581 rc = clk_set_rate(dev->external_clk, STD_EXT_CLK_FREQ);
582 if (rc) {
583 dev_err(dev->device, "%s: clk_set_rate returned %d\n",
584 __func__, rc);
585 }
586
587 return rc;
588 }
589
590 /* Master transfer function */
bcm_kona_i2c_xfer(struct i2c_adapter * adapter,struct i2c_msg msgs[],int num)591 static int bcm_kona_i2c_xfer(struct i2c_adapter *adapter,
592 struct i2c_msg msgs[], int num)
593 {
594 struct bcm_kona_i2c_dev *dev = i2c_get_adapdata(adapter);
595 struct i2c_msg *pmsg;
596 int rc = 0;
597 int i;
598
599 rc = clk_prepare_enable(dev->external_clk);
600 if (rc) {
601 dev_err(dev->device, "%s: peri clock enable failed. err %d\n",
602 __func__, rc);
603 return rc;
604 }
605
606 /* Enable pad output */
607 writel(0, dev->base + PADCTL_OFFSET);
608
609 /* Enable internal clocks */
610 bcm_kona_i2c_enable_clock(dev);
611
612 /* Send start command */
613 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_START);
614 if (rc < 0) {
615 dev_err(dev->device, "Start command failed rc = %d\n", rc);
616 goto xfer_disable_pad;
617 }
618
619 /* Switch to high speed if applicable */
620 if (dev->hs_cfg) {
621 rc = bcm_kona_i2c_switch_to_hs(dev);
622 if (rc < 0)
623 goto xfer_send_stop;
624 }
625
626 /* Loop through all messages */
627 for (i = 0; i < num; i++) {
628 pmsg = &msgs[i];
629
630 /* Send restart for subsequent messages */
631 if ((i != 0) && ((pmsg->flags & I2C_M_NOSTART) == 0)) {
632 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART);
633 if (rc < 0) {
634 dev_err(dev->device,
635 "restart cmd failed rc = %d\n", rc);
636 goto xfer_send_stop;
637 }
638 }
639
640 /* Send slave address */
641 if (!(pmsg->flags & I2C_M_NOSTART)) {
642 rc = bcm_kona_i2c_do_addr(dev, pmsg);
643 if (rc < 0) {
644 dev_err(dev->device,
645 "NAK from addr %2.2x msg#%d rc = %d\n",
646 pmsg->addr, i, rc);
647 goto xfer_send_stop;
648 }
649 }
650
651 /* Perform data transfer */
652 if (pmsg->flags & I2C_M_RD) {
653 rc = bcm_kona_i2c_read_fifo(dev, pmsg);
654 if (rc < 0) {
655 dev_err(dev->device, "read failure\n");
656 goto xfer_send_stop;
657 }
658 } else {
659 rc = bcm_kona_i2c_write_fifo(dev, pmsg);
660 if (rc < 0) {
661 dev_err(dev->device, "write failure");
662 goto xfer_send_stop;
663 }
664 }
665 }
666
667 rc = num;
668
669 xfer_send_stop:
670 /* Send a STOP command */
671 bcm_kona_send_i2c_cmd(dev, BCM_CMD_STOP);
672
673 /* Return from high speed if applicable */
674 if (dev->hs_cfg) {
675 int hs_rc = bcm_kona_i2c_switch_to_std(dev);
676
677 if (hs_rc)
678 rc = hs_rc;
679 }
680
681 xfer_disable_pad:
682 /* Disable pad output */
683 writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET);
684
685 /* Stop internal clock */
686 bcm_kona_i2c_disable_clock(dev);
687
688 clk_disable_unprepare(dev->external_clk);
689
690 return rc;
691 }
692
bcm_kona_i2c_functionality(struct i2c_adapter * adap)693 static uint32_t bcm_kona_i2c_functionality(struct i2c_adapter *adap)
694 {
695 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR |
696 I2C_FUNC_NOSTART;
697 }
698
699 static const struct i2c_algorithm bcm_algo = {
700 .master_xfer = bcm_kona_i2c_xfer,
701 .functionality = bcm_kona_i2c_functionality,
702 };
703
bcm_kona_i2c_assign_bus_speed(struct bcm_kona_i2c_dev * dev)704 static int bcm_kona_i2c_assign_bus_speed(struct bcm_kona_i2c_dev *dev)
705 {
706 unsigned int bus_speed;
707 int ret = of_property_read_u32(dev->device->of_node, "clock-frequency",
708 &bus_speed);
709 if (ret < 0) {
710 dev_err(dev->device, "missing clock-frequency property\n");
711 return -ENODEV;
712 }
713
714 switch (bus_speed) {
715 case I2C_MAX_STANDARD_MODE_FREQ:
716 dev->std_cfg = &std_cfg_table[BCM_SPD_100K];
717 break;
718 case I2C_MAX_FAST_MODE_FREQ:
719 dev->std_cfg = &std_cfg_table[BCM_SPD_400K];
720 break;
721 case I2C_MAX_FAST_MODE_PLUS_FREQ:
722 dev->std_cfg = &std_cfg_table[BCM_SPD_1MHZ];
723 break;
724 case I2C_MAX_HIGH_SPEED_MODE_FREQ:
725 /* Send mastercode at 100k */
726 dev->std_cfg = &std_cfg_table[BCM_SPD_100K];
727 dev->hs_cfg = &hs_cfg_table[BCM_SPD_3P4MHZ];
728 break;
729 default:
730 pr_err("%d hz bus speed not supported\n", bus_speed);
731 pr_err("Valid speeds are 100khz, 400khz, 1mhz, and 3.4mhz\n");
732 return -EINVAL;
733 }
734
735 return 0;
736 }
737
bcm_kona_i2c_probe(struct platform_device * pdev)738 static int bcm_kona_i2c_probe(struct platform_device *pdev)
739 {
740 int rc = 0;
741 struct bcm_kona_i2c_dev *dev;
742 struct i2c_adapter *adap;
743
744 /* Allocate memory for private data structure */
745 dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
746 if (!dev)
747 return -ENOMEM;
748
749 platform_set_drvdata(pdev, dev);
750 dev->device = &pdev->dev;
751 init_completion(&dev->done);
752
753 /* Map hardware registers */
754 dev->base = devm_platform_ioremap_resource(pdev, 0);
755 if (IS_ERR(dev->base))
756 return PTR_ERR(dev->base);
757
758 /* Get and enable external clock */
759 dev->external_clk = devm_clk_get(dev->device, NULL);
760 if (IS_ERR(dev->external_clk)) {
761 dev_err(dev->device, "couldn't get clock\n");
762 return -ENODEV;
763 }
764
765 rc = clk_set_rate(dev->external_clk, STD_EXT_CLK_FREQ);
766 if (rc) {
767 dev_err(dev->device, "%s: clk_set_rate returned %d\n",
768 __func__, rc);
769 return rc;
770 }
771
772 rc = clk_prepare_enable(dev->external_clk);
773 if (rc) {
774 dev_err(dev->device, "couldn't enable clock\n");
775 return rc;
776 }
777
778 /* Parse bus speed */
779 rc = bcm_kona_i2c_assign_bus_speed(dev);
780 if (rc)
781 goto probe_disable_clk;
782
783 /* Enable internal clocks */
784 bcm_kona_i2c_enable_clock(dev);
785
786 /* Configure internal dividers */
787 bcm_kona_i2c_config_timing(dev);
788
789 /* Disable timeout */
790 writel(0, dev->base + TOUT_OFFSET);
791
792 /* Enable autosense */
793 bcm_kona_i2c_enable_autosense(dev);
794
795 /* Enable TX FIFO */
796 writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK,
797 dev->base + TXFCR_OFFSET);
798
799 /* Mask all interrupts */
800 writel(0, dev->base + IER_OFFSET);
801
802 /* Clear all pending interrupts */
803 writel(ISR_CMDBUSY_MASK |
804 ISR_READ_COMPLETE_MASK |
805 ISR_SES_DONE_MASK |
806 ISR_ERR_MASK |
807 ISR_TXFIFOEMPTY_MASK |
808 ISR_NOACK_MASK,
809 dev->base + ISR_OFFSET);
810
811 /* Get the interrupt number */
812 dev->irq = platform_get_irq(pdev, 0);
813 if (dev->irq < 0) {
814 rc = dev->irq;
815 goto probe_disable_clk;
816 }
817
818 /* register the ISR handler */
819 rc = devm_request_irq(&pdev->dev, dev->irq, bcm_kona_i2c_isr,
820 IRQF_SHARED, pdev->name, dev);
821 if (rc) {
822 dev_err(dev->device, "failed to request irq %i\n", dev->irq);
823 goto probe_disable_clk;
824 }
825
826 /* Enable the controller but leave it idle */
827 bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION);
828
829 /* Disable pad output */
830 writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET);
831
832 /* Disable internal clock */
833 bcm_kona_i2c_disable_clock(dev);
834
835 /* Disable external clock */
836 clk_disable_unprepare(dev->external_clk);
837
838 /* Add the i2c adapter */
839 adap = &dev->adapter;
840 i2c_set_adapdata(adap, dev);
841 adap->owner = THIS_MODULE;
842 strscpy(adap->name, "Broadcom I2C adapter", sizeof(adap->name));
843 adap->algo = &bcm_algo;
844 adap->dev.parent = &pdev->dev;
845 adap->dev.of_node = pdev->dev.of_node;
846
847 rc = i2c_add_adapter(adap);
848 if (rc)
849 return rc;
850
851 dev_info(dev->device, "device registered successfully\n");
852
853 return 0;
854
855 probe_disable_clk:
856 bcm_kona_i2c_disable_clock(dev);
857 clk_disable_unprepare(dev->external_clk);
858
859 return rc;
860 }
861
bcm_kona_i2c_remove(struct platform_device * pdev)862 static int bcm_kona_i2c_remove(struct platform_device *pdev)
863 {
864 struct bcm_kona_i2c_dev *dev = platform_get_drvdata(pdev);
865
866 i2c_del_adapter(&dev->adapter);
867
868 return 0;
869 }
870
871 static const struct of_device_id bcm_kona_i2c_of_match[] = {
872 {.compatible = "brcm,kona-i2c",},
873 {},
874 };
875 MODULE_DEVICE_TABLE(of, bcm_kona_i2c_of_match);
876
877 static struct platform_driver bcm_kona_i2c_driver = {
878 .driver = {
879 .name = "bcm-kona-i2c",
880 .of_match_table = bcm_kona_i2c_of_match,
881 },
882 .probe = bcm_kona_i2c_probe,
883 .remove = bcm_kona_i2c_remove,
884 };
885 module_platform_driver(bcm_kona_i2c_driver);
886
887 MODULE_AUTHOR("Tim Kryger <tkryger@broadcom.com>");
888 MODULE_DESCRIPTION("Broadcom Kona I2C Driver");
889 MODULE_LICENSE("GPL v2");
890