Searched full:depending (Results 1 – 25 of 543) sorted by relevance
12345678910>>...22
| /Documentation/hwmon/ |
| D | gsc-hwmon.rst | 21 The voltage inputs are scaled either internally or by the driver depending
33 either internally or by the driver depending on the GSC version and firmware.
44 PWM value will be scaled depending on 6 temperature boundaries.
|
| D | adm1275.rst | 103 inX_label "vin1" or "vout1" depending on chip variant and
118 curr1_lcrit Critical minimum current. Depending on the chip
122 curr1_crit Critical maximum current. Depending on the chip
|
| D | ltc2945.rst | 56 SENSE+ or VDD pin depending on chip configuration.
84 voltage or ADIN voltage depending on chip configuration.
|
| D | nct6775.rst | 103 PCH, and SMBUS. Depending on the chip type, 2 to 6 of the temperature sources
114 either 1 degC or 0.5 degC, depending on the temperature source and
117 value. Alarms are only supported for temp1 to temp6, depending on the chip type.
251 There are up to seven data points depending on the chip type. Subsequent data
|
| /Documentation/driver-api/thermal/ |
| D | nouveau_thermal.rst | 41 Some of these thresholds may not be used by Nouveau depending
79 * 2; The fan is driven automatically depending on the temperature.
87 depending on your hardware.
|
| /Documentation/PCI/endpoint/function/binding/ |
| D | pci-test.rst | 22 msi_interrupts Should be 1 to 32 depending on the number of MSI interrupts
24 msix_interrupts Should be 1 to 2048 depending on the number of MSI-X
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-adc-hi8435 | 18 Depending on in_voltageY_sensing_mode the low voltage threshold
37 Depending on in_voltageY_sensing_mode the high voltage threshold
|
| D | sysfs-class-power-surface | 14 Valid values: In micro-Wh or micro-Ah, depending on the power unit
|
| D | sysfs-bus-iio-dma-buffer | 16 depending on which and how many channels are enabled. Whereas
|
| /Documentation/sound/soc/ |
| D | clocking.rst | 18 their speed can be altered by software (depending on the system use and to save
39 it is best to configure BCLK to the lowest possible speed (depending on your
|
| D | pops-clicks.rst | 12 depending on the audio usage and this can subsequently cause a small pop or
39 playback in that components are powered in a sequence depending upon stream
|
| D | dai.rst | 30 usually varies depending on the sample rate and the master system clock
53 receive the audio data. Bit clock usually varies depending on sample rate
|
| D | jack.rst | 41 These represent a DAPM pin to update depending on some of the status
69 These are all hooked together by the machine driver depending on the
|
| /Documentation/devicetree/bindings/interconnect/ |
| D | interconnect.txt | 15 depending on the use case. Interconnect providers can also be interconnect
42 multiple paths from different providers depending on use case and the
|
| /Documentation/devicetree/bindings/arm/omap/ |
| D | iva.txt | 4 depending of the version.
|
| /Documentation/misc-devices/ |
| D | tps6594-pfsm.rst | 16 manages operational modes. Depending on the current operational mode,
65 Depending on the triggers set, some DDR/GPIO voltage domains can
|
| D | apds990x.rst | 26 might vary quite much depending the spectrum of the light source.
68 to saturate much before that. Real max value varies depending
|
| /Documentation/netlabel/ |
| D | lsm_interface.rst | 26 low-level packet label depending on the NetLabel build time and run time
43 Depending on the exact configuration, translation between the network packet
|
| /Documentation/devicetree/bindings/sound/ |
| D | rt1015.txt | 15 this value is adjustable depending on platform.
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | sx8654.txt | 4 - compatible: must be one of the following, depending on the model:
|
| /Documentation/devicetree/bindings/regulator/ |
| D | palmas-pmic.txt | 35 For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP,
36 smps45, smps457, smps7 depending on variant, smps6, smps[8-9],
|
| /Documentation/admin-guide/media/ |
| D | saa7134.rst | 52 Depending on the card you might have to pass ``card=<nr>`` as insmod option.
82 default might not work for you depending on which version you have.
|
| /Documentation/devicetree/bindings/arm/amlogic/ |
| D | pmu.txt | 8 - compatible value : depending on the SoC this should be one of:
|
| D | analog-top.txt | 9 - compatible: depending on the SoC this should be one of:
|
| /Documentation/userspace-api/media/v4l/ |
| D | tuner.rst | 15 depending on the number of RF connectors on the tuner. The ``type``
47 video outputs, depending on the number of RF connectors on the
|
12345678910>>...22