Home
last modified time | relevance | path

Searched refs:SAR (Results 1 – 11 of 11) sorted by relevance

/drivers/platform/x86/intel/int1092/
DKconfig7 M.2 modem to regulate the RF power based on SAR data obtained from the
9 to SAR driver. The front end application in userspace will interact with SAR
11 SAR table index and use available communication like MBIM interface to enable
13 given platform needs to support "Dynamic SAR" configuration for a modem available
/drivers/dma/
Dtxx9dmac.h72 u64 SAR; /* Source Address Register */ member
82 u32 SAR; member
206 u64 SAR; member
212 u32 SAR; member
Dtxx9dmac.c290 channel64_readq(dc, SAR), in txx9dmac_dump_regs()
302 channel32_readl(dc, SAR), in txx9dmac_dump_regs()
316 channel_writeq(dc, SAR, 0); in txx9dmac_reset_chan()
320 channel_writel(dc, SAR, 0); in txx9dmac_reset_chan()
474 (u64)desc->CHAR, desc->SAR, desc->DAR, desc->CNTR); in txx9dmac_dump_desc()
479 (u64)desc->CHAR, desc->SAR, desc->DAR, desc->CNTR, in txx9dmac_dump_desc()
487 d->CHAR, d->SAR, d->DAR, d->CNTR); in txx9dmac_dump_desc()
492 d->CHAR, d->SAR, d->DAR, d->CNTR, in txx9dmac_dump_desc()
755 desc->hwdesc.SAR = src + offset; in txx9dmac_prep_dma_memcpy()
761 desc->hwdesc32.SAR = src + offset; in txx9dmac_prep_dma_memcpy()
[all …]
Didma64.c94 channel_writeq(idma64c, SAR, 0); in idma64_chan_start()
Dpl330.c339 SAR = 0, enumerator
732 dst == SAR ? "SAR" : (dst == DAR ? "DAR" : "CCR"), val); in _emit_MOV()
1400 off += _emit_MOV(dry_run, &buf[off], SAR, x->src_addr); in _setup_xfer()
/drivers/i2c/busses/
Di2c-rcar.c70 #define SAR BIT(0) /* slave addr received */ macro
608 if (ssr_filtered & SAR) { in rcar_i2c_slave_irq()
613 rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR); in rcar_i2c_slave_irq()
617 rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR); in rcar_i2c_slave_irq()
621 rcar_i2c_write(priv, ICSSR, ~(SAR | SSR) & 0xff); in rcar_i2c_slave_irq()
628 rcar_i2c_write(priv, ICSIER, SAR); in rcar_i2c_slave_irq()
975 rcar_i2c_write(priv, ICSIER, SAR); in rcar_reg_slave()
/drivers/net/wireless/ath/ath9k/
DKconfig88 TX99 support enables Specific Absorption Rate (SAR) testing.
89 SAR is the unit of measurement for the amount of radio frequency(RF)
91 limits used are expressed in the terms of SAR, which is a measure
96 governmental SAR regulations.
/drivers/dma/sh/
Dshdmac.c37 #define SAR 0x00 /* Source Address Register */ macro
216 sh_dmae_writel(sh_chan, hw->sar, SAR); in dmae_set_reg()
459 u32 sar_buf = sh_dmae_readl(sh_chan, SAR); in sh_dmae_desc_completed()
/drivers/dma/dw/
Dregs.h40 DW_REG(SAR); /* Source Address Register */
Dcore.c131 channel_readl(dwc, SAR), in dwc_dump_chan_regs()
160 channel_writel(dwc, SAR, lli_read(desc, sar)); in dwc_do_single_block()
/drivers/iio/adc/
DKconfig841 tristate "Amlogic Meson SAR ADC driver"
846 Say yes here to build support for the SAR ADC found in Amlogic Meson