Searched full:pa0 (Results 1 – 25 of 43) sorted by relevance
12
| /kernel/linux/linux-5.10/drivers/staging/pi433/ |
| D | rf69.c | 353 bool pa0, pa1, pa2, high_power; in rf69_set_output_power_level() local
358 pa0 = pa_level & MASK_PALEVEL_PA0; in rf69_set_output_power_level()
368 if (pa0 && !pa1 && !pa2) { in rf69_set_output_power_level()
371 } else if (!pa0 && pa1 && !pa2) { in rf69_set_output_power_level()
374 } else if (!pa0 && pa1 && pa2) { in rf69_set_output_power_level()
|
| /kernel/linux/linux-5.10/Documentation/driver-api/media/drivers/ |
| D | saa7134-devel.rst | 45 - nc MDT2005 PA0 pin 17 strap low
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | ingenic,pinctrl.yaml | 19 pin within that GPIO port. For example PA0 is the first pin in GPIO port A,
|
| D | atmel,at91-pinctrl.txt | 47 PA0 MCDB0
|
| D | st,stm32-pinctrl.yaml | 133 - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | sun5i-a10s.dtsi | 141 pins = "PA0", "PA1", "PA2",
|
| D | at91sam9263.dtsi | 293 AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA0 periph A with pullup */
385 <AT91_PIOA 0 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA0 periph B SPI0_MISO pin */
|
| D | at91sam9260.dtsi | 369 AT91_PIOA 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA0 periph B with pullup */
399 <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA0 periph A SPI0_MISO pin */
|
| D | sun7i-a20.dtsi | 846 pins = "PA0", "PA1", "PA2",
866 pins = "PA0", "PA1", "PA2",
876 pins = "PA0", "PA1", "PA2",
1095 pins = "PA0", "PA1";
|
| D | sun4i-a10-inet9f-rev03.dts | 111 gpios = <&pio 0 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA0 */
|
| D | sun6i-a31.dtsi | 626 pins = "PA0", "PA1", "PA2", "PA3",
642 pins = "PA0", "PA1", "PA2", "PA3",
651 pins = "PA0", "PA1", "PA2", "PA3",
|
| D | at91rm9200.dtsi | 545 <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA0 periph A SPI0_MISO pin */
|
| D | at91sam9n12.dtsi | 312 AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA0 periph A */
|
| D | sunxi-h3-h5.dtsi | 494 pins = "PA0", "PA1";
|
| D | tegra30-apalis.dtsi | 682 clk-32k-out-pa0 {
|
| D | tegra30-apalis-v1.1.dtsi | 692 clk-32k-out-pa0 {
|
| D | at91sam9g45.dtsi | 413 <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA0 periph A */
|
| D | sun8i-r40.dtsi | 513 pins = "PA0", "PA1", "PA2", "PA3",
|
| D | sun9i-a80.dtsi | 980 pins = "PA0", "PA1", "PA2", "PA3", "PA4", "PA5",
|
| /kernel/linux/linux-5.10/arch/m68k/include/asm/ |
| D | MC68EZ328.h | 1162 #define DRAMMC_COL10 0x0080 /* Col address bit for MD10 PA11/PA0 */
1163 #define DRAMMC_COL9 0x0040 /* Col address bit for MD9 PA10/PA0 */
1164 #define DRAMMC_COL8 0x0020 /* Col address bit for MD8 PA9/PA0 */
|
| D | MC68VZ328.h | 1257 #define DRAMMC_COL10 0x0080 /* Col address bit for MD10 PA11/PA0 */
1258 #define DRAMMC_COL9 0x0040 /* Col address bit for MD9 PA10/PA0 */
1259 #define DRAMMC_COL8 0x0020 /* Col address bit for MD8 PA9/PA0 */
|
| /kernel/linux/linux-5.10/drivers/parport/ |
| D | parport_mfc3.c | 46 * 2 | PA0 | <-- | BUSY (same as CA1!)
|
| /kernel/linux/linux-5.10/drivers/pinctrl/renesas/ |
| D | pfc-shx3.c | 294 PINMUX_GPIO(PA0),
|
| D | pfc-sh7786.c | 416 PINMUX_GPIO(PA0),
|
| D | pfc-sh7785.c | 680 PINMUX_GPIO(PA0),
|
12