| /kernel/linux/linux-5.10/drivers/net/phy/ |
| D | dp83867.c | 399 phydev_err(phydev, in dp83867_set_downshift()
475 phydev_err(phydev, "ti,rx-internal-delay must be specified\n"); in dp83867_verify_rgmii_cfg()
483 phydev_err(phydev, "ti,tx-internal-delay must be specified\n"); in dp83867_verify_rgmii_cfg()
512 phydev_err(phydev, "ti,clk-output-sel value %u out of range\n", in dp83867_of_init()
535 phydev_err(phydev, in dp83867_of_init()
545 phydev_err(phydev, in dp83867_of_init()
568 phydev_err(phydev, "tx-fifo-depth value %u out of range\n", in dp83867_of_init()
579 phydev_err(phydev, "rx-fifo-depth value %u out of range\n", in dp83867_of_init()
|
| D | dp83869.c | 316 phydev_err(phydev, "Failed to read RX CFG\n"); in dp83869_get_wol()
333 phydev_err(phydev, "Failed to read RX SOP 1\n"); in dp83869_get_wol()
343 phydev_err(phydev, "Failed to read RX SOP 2\n"); in dp83869_get_wol()
353 phydev_err(phydev, "Failed to read RX SOP 3\n"); in dp83869_get_wol()
425 phydev_err(phydev, in dp83869_set_downshift()
|
| D | micrel.c | 227 phydev_err(phydev, "failed to set led mode\n"); in kszphy_setup_led()
246 phydev_err(phydev, "failed to disable broadcast address\n"); in kszphy_broadcast_disable()
266 phydev_err(phydev, "failed to disable NAND tree mode\n"); in kszphy_nand_tree_disable()
280 phydev_err(phydev, in kszphy_config_reset()
770 phydev_err(phydev, "failed to force the phy to master mode\n"); in ksz9031_config_init()
1122 phydev_err(phydev, "invalid led mode: 0x%02x\n", in kszphy_probe()
1146 phydev_err(phydev, "Clock rate out of range: %ld\n", in kszphy_probe()
|
| D | cortina.c | 68 phydev_err(phydev, "Error matching phy with %s driver\n", in cortina_probe()
|
| D | at803x.c | 391 phydev_err(phydev, "failed to register VDDIO regulator\n"); in at8031_register_regulators()
397 phydev_err(phydev, "failed to register VDDH regulator\n"); in at8031_register_regulators()
437 phydev_err(phydev, "invalid qca,clk-out-frequency\n"); in at803x_parse_dt()
476 phydev_err(phydev, "invalid qca,clk-out-strength\n"); in at803x_parse_dt()
495 phydev_err(phydev, "failed to get VDDIO regulator\n"); in at803x_parse_dt()
|
| D | phy_device.c | 542 phydev_err(dev, "error %d loading PHY driver module for ID 0x%08lx\n", in phy_request_driver_module()
878 phydev_err(phydev, "failed to initialize\n"); in phy_device_register()
884 phydev_err(phydev, "failed to add\n"); in phy_device_register()
1315 phydev_err(phydev, "failed to get the bus module\n"); in phy_attach_direct()
1334 phydev_err(phydev, "failed to get the device driver module\n"); in phy_attach_direct()
1379 phydev_err(phydev, "error creating 'phy_standalone' sysfs entry\n"); in phy_attach_direct()
2259 phydev_err(phydev, "Master/Slave resolution failed, maybe conflicting manual settings?\n"); in genphy_read_lpa()
2261 phydev_err(phydev, "Master/Slave resolution failed\n"); in genphy_read_lpa()
2776 phydev_err(phydev, "Delay %d is out of range\n", delay); in phy_get_internal_delay()
2798 phydev_err(phydev, "error finding internal delay index for %d\n", in phy_get_internal_delay()
|
| D | rockchip.c | 116 phydev_err(phydev, "rockchip_integrated_phy_analog_init err: %d.\n", in rockchip_link_change_notify()
|
| D | bcm87xx.c | 163 phydev_err(phydev, in bcm87xx_did_interrupt()
|
| D | aquantia_main.c | 208 phydev_err(phydev, "Reading HW Statistics failed for %s\n", in aqr107_get_stats()
598 phydev_err(phydev, "timeout: processor-intensive MDIO operation\n"); in aqr107_wait_processor_intensive_op()
|
| D | adin.c | 471 phydev_err(phydev, in adin_cl45_to_adin_reg()
|
| D | phy.c | 465 phydev_err(phydev, "Error while aborting cable test"); in phy_abort_cable_test()
|
| D | marvell.c | 1781 phydev_err(phydev, "Timeout while waiting for cable test to finish\n"); in marvell_vct5_wait_complete()
|
| /kernel/linux/linux-5.10/include/linux/ |
| D | phy.h | 954 phydev_err(phydev, "%s failed: %d\n", __func__, __ret); \
1052 phydev_err(phydev, "%s failed: %d\n", __func__, __ret); \
1436 #define phydev_err(_phydev, format, args...) \ macro
|
| /kernel/linux/linux-5.10/net/ethtool/ |
| D | cabletest.c | 51 phydev_err(phydev, "%s: Error %pe\n", __func__, ERR_PTR(err)); in ethnl_cable_test_started()
|
| /kernel/linux/linux-5.10/drivers/net/phy/mscc/ |
| D | mscc_main.c | 261 phydev_err(phydev, "Downshift count should be 2,3,4 or 5\n"); in vsc85xx_downshift_set()
428 phydev_err(phydev, "DT %s invalid\n", led); in vsc85xx_dt_led_mode_get()
|
| D | mscc_ptp.c | 1571 phydev_err(phydev, "Can't get load-save GPIO (%ld)\n", in vsc8584_ptp_probe()
|