Lines Matching +full:reference +full:- +full:doubler +full:- +full:enable
1 # SPDX-License-Identifier: GPL-2.0-only
18 CD-ROM drives.
26 module will be called ide-core.
61 a few first-generation SATA controllers.
78 The module will be called ide-gd_mod.
97 (i.e. Iomega ZIP or MKE LS-120).
101 <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
110 and CD-ROM drives connected through a PCMCIA card.
125 If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
126 a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
127 SCSI protocol. Most new CD-ROM drives use ATAPI, including the
128 NEC-260, Mitsumi FX400, Sony 55E, and just about all non-SCSI
131 If you say Y here, the CD-ROM drive will be identified at boot time
134 CD-ROM drive, you can say N to all other CD-ROM options, but be sure
135 to say Y or M to "ISO 9660 CD-ROM file system support".
138 module will be called ide-cd.
146 ATAPI error codes. This will use up additional 8kB of kernel-space
154 ATAPI is a newer protocol used by IDE tape and CD-ROM drives,
158 You should also say Y if you have an OnStream DI-30 tape drive; this
160 SC-30 and SC-50 versions.
166 <file:drivers/ide/ide-tape.c> and <file:Documentation/ide/ide.rst>
170 module will be called ide-tape.
185 basic form of media-forensics.
236 The CMD-Technologies CMD640 IDE chip is used on many common 486 and
248 to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man
252 The CMD640 chip is also used on add-in cards by Acculogic, and on
253 the "CSA-6400E PCI to IDE controller" that some people have. For
301 bool "Boot off-board chipsets first support (DEPRECATED)"
304 Normally, IDE controllers built into the motherboard (on-board
305 controllers) are assigned to ide0 and ide1 while those on add-in PCI
306 cards (off-board controllers) are relegated to ide2 and ide3.
308 off-board controllers on ide0/1 and on-board controllers on ide2/3.
310 when booting from a drive on an off-board controller.
340 The PC-Technologies RZ1000 IDE chip is used on many common 486 and
381 This driver adds explicit support for AMD-7xx and AMD-8111 chips
410 as those commonly found on Compaq Pentium-Pro systems
419 used on Digital's PC-Alpha 164SX boards.
466 HPT366 is an Ultra DMA chipset for ATA-66.
467 HPT368 is an Ultra DMA chipset for ATA-66 RAID Based.
468 HPT370 is an Ultra DMA chipset for ATA-100.
469 HPT372 is an Ultra DMA chipset for ATA-100.
470 HPT374 is an Ultra DMA chipset for ATA-100.
477 reference to device 0x80. The other solution is to say Y to "Boot
478 off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless
483 ide-probe at boot. It is reported to support DVD II drives, by the
498 This driver adds support for the on-board IDE controller on the
527 IT 8212 IDE RAID controller in both RAID and pass-through mode.
534 (used mainly on SPARC64 and PA-RISC machines).
547 interrupt. This add-on card is a bootable PCI UDMA controller. Since
549 happen if the BIOS revisions of all installed cards (three-max) do
551 at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required
600 If you have a Winbond SL82c105 IDE controller, say Y here to enable
612 look-a-like to the PIIX4 it should be a nice addition.
639 This driver adds support for Toshiba TC86C001 GOKU-S chip.
643 # TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
645 tristate "PowerMac on-board IDE support"
650 This driver provides support for the on-board IDE controller on
655 bool "Probe on-board ATA/100 (Kauai) first"
662 CD-ROM on hda. This option changes this to more natural hda for
663 hard disk and hdc for CD-ROM.
703 This includes on-board IDE interfaces on some Amiga models (A600,
705 bus (M-Tech E-Matrix 530 expansion card).
707 It also provides support for the so-called `IDE doublers' (made
709 the on-board IDE interface of some Amiga models. Using such an IDE
710 doubler, you can connect up to four instead of two IDE devices to
711 the Amiga's on-board IDE interface. The feature is enabled at kernel
712 runtime using the "gayle.doubler" kernel boot parameter.
715 IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
718 Note that you also have to enable Zorro bus support if you want to
722 tristate "Buddha/Catweasel/X-Surf IDE interface support"
726 and X-Surf expansion boards. It supports up to two interfaces on the
727 Buddha, three on the Catweasel and two on the X-Surf.
730 use IDE devices (hard disks, CD-ROM drives, etc.) that are connected
737 This is the IDE driver for the on-board IDE interface on the Atari
739 disks, CD-ROM drives, etc.) that are connected to the on-board IDE
746 This is the IDE driver for the on-board IDE interface on some m68k
753 devices (hard disks, CD-ROM drives, etc.) that are connected to the
754 on-board IDE interface.
760 Enable the on-board IDE controller in the Q40/Q60. This should
773 # no isa -> no vlb
785 runtime using the "ide-4drives.probe" kernel boot parameter if you
801 tristate "DTC-2278 support"
807 of the DTC-2278 card, and permits faster I/O speeds to be set as
833 tristate "UMC-8672 support"
839 of the UMC-8672, and permits faster I/O speeds to be set as well.