Lines Matching +full:attribute +full:- +full:set
6 * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
13 * Copyright 2015-2017 Intel Deutschland GmbH
14 * Copyright (C) 2018-2020 Intel Corporation
32 * be careful not to break things - i.e. don't move anything around or so
74 * - a setup station entry is added, not yet authorized, without any rate
76 * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
79 * - %NL80211_TDLS_ENABLE_LINK is then used
80 * - after this, the only valid operation is to remove it by tearing down
95 * Frame registration is done on a per-interface basis and registrations
132 * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the
137 * software, like the AP-VLAN type in mac80211 for example, there's
139 * are only restricted by some semantic restrictions (e.g. AP-VLAN
141 * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
144 * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically,
168 * a) Expiration of hardware timer whose expiration time is set to maximum
193 * set by drivers indicating offload support of the PTK/GTK EAPOL
196 * %NL80211_ATTR_WANT_1X_4WAY_HS attribute flag. Drivers supporting this
197 * offload may reject the %NL80211_CMD_CONNECT when the attribute flag is
208 * For 802.1X the PMK or PMK-R0 are set by providing %NL80211_ATTR_PMK
223 * %NL80211_ATTR_FILS_ERP_USERNAME - used to construct keyname_nai
224 * %NL80211_ATTR_FILS_ERP_REALM - used to construct keyname_nai
225 * %NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM - used to construct erp message
226 * %NL80211_ATTR_FILS_ERP_RRK - used to generate the rIK and rMSK
235 * %NL80211_ATTR_FILS_KEK - used for key renewal
236 * %NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM - used in further EAP-RP exchanges
237 * %NL80211_ATTR_PMKID - used to identify the PMKSA used/generated
238 * %Nl80211_ATTR_PMK - used to update PMKSA cache in userspace
255 * support offloading SAE authentication for WPA3-Personal networks in station
256 * mode. Similarly @NL80211_EXT_FEATURE_SAE_OFFLOAD_AP flag can be set by
269 * single netdev that uses VLAN tagged frames and separate VLAN-specific netdevs
284 * attribute given in wiphy capabilities.
294 * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values
304 * enum nl80211_commands - supported nl80211 commands
310 * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
311 * %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
329 * @NL80211_CMD_SET_INTERFACE: Set type of a virtual interface, requires
340 * attribute %NL80211_ATTR_IFINDEX.
344 * @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT,
367 * The channel to use can be set on the interface or be given using the
376 * @NL80211_CMD_SET_STATION: Set station attributes for station identified by
391 * @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to
403 * @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by
406 * @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set
416 * If a wiphy is self-managed (%NL80211_ATTR_WIPHY_SELF_MANAGED_REG), then
419 * @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command
421 * domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our
423 * NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each
424 * regulatory rule is a nested set of attributes given by
429 * @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
430 * to the specified ISO/IEC 3166-1 alpha2 country code. The core will
436 * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
439 * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
447 * point to avoid re-using existing command number. The functionality this
482 * using the %NL80211_ATTR_IE attribute. The first cycle of the
485 * scans, it will allow such when the caller provides the flag attribute
486 * %NL80211_ATTR_SCHED_SCAN_MULTI to indicate user-space support for it.
487 * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT if
526 * set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is
533 * if you are world roaming (regulatory domain set to world or if your
538 * never be used for channels 1-11 on the 2 GHz band as they are always
563 * state. This is similar to MLME-AUTHENTICATE.confirm primitive in the
565 * included %NL80211_ATTR_FRAME attribute contains the management frame
568 * case the %NL80211_ATTR_FRAME attribute is replaced with a
573 * (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request,
574 * MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives). The
575 * %NL80211_ATTR_PREV_BSSID attribute is used to specify whether the
576 * request is for the initial association to an ESS (that attribute not
577 * included) or for reassociation within the ESS (that attribute is
581 * MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication
585 * MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives).
593 * event matches with MLME-MICHAELMICFAILURE.indication() primitive
595 * @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a
596 * FREQ attribute (for the initial frequency if no peer can be found)
597 * and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those
601 * given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not
603 * @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is
606 * @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute
607 * to identify the device, and the TESTDATA blob attribute to pass through
613 * %NL80211_ATTR_SSID attribute, and can optionally specify the association
627 * set of BSSID,frequency parameters is used (i.e., either the enforcing
645 * This attribute is ignored if driver does not support roam scan.
648 * determined by the %NL80211_ATTR_STATUS_CODE attribute (0 = success,
649 * non-zero = failure). If %NL80211_ATTR_TIMED_OUT is included in the
652 * Non-zero %NL80211_ATTR_STATUS_CODE value is indicated in that case as
663 * @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices
668 * off-channel operations like transmit a Public Action frame and wait for
682 * pending remain-on-channel duration if the desired operation has been
685 * radio. The %NL80211_ATTR_COOKIE attribute must be given as well to
688 * remain-on-channel duration has expired.
690 * @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX
692 * and @NL80211_ATTR_TX_RATES the set of allowed rates.
696 * requires an interface index, a frame type attribute (optional for
698 * and a match attribute containing the first few bytes of the frame
703 * The %NL80211_ATTR_RECEIVE_MULTICAST flag attribute can be given if
716 * received. If this channel is not the current channel (remain-on-channel
725 * counters which will be updated to the current value. This attribute
727 * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
730 * also sent as an event whenever the driver has completed the off-channel
741 * @NL80211_CMD_SET_POWER_SAVE: Set powersave, using %NL80211_ATTR_PS_STATE
750 * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
754 * with which it switches channels is implementation-defined.
760 * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
778 * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
793 * @NL80211_MESH_SETUP_USERSPACE_MPM is set. On reception of this
800 * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings.
801 * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings.
804 * command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
809 * @NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason
818 * contains the data in sub-attributes). After rekeying happened,
825 * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
827 * actions on TDLS links (set up a new link or tear down an existing one).
833 * %NL80211_ATTR_TDLS_ACTION attribute determines the type of frame to be
834 * sent. Public Action codes (802.11-2012 8.1.5.1) will be sent as
835 * 802.11 management frames, while TDLS action codes (802.11-2012
846 * For the event, the %NL80211_ATTR_MAC attribute carries the TA and
854 * and wasn't already in a 4-addr VLAN. The event will be sent similarly
863 * has %NL80211_ATTR_ACK set if the frame was ACKed.
877 * sent when a remotely-initiated switch (e.g., when a STA receives a CSA
892 * P2P Device can be used for P2P operations, e.g. remain-on-channel and
927 * @NL80211_CMD_UPDATE_FT_IES: Pass down the most up-to-date Fast Transition
935 * @NL80211_CMD_CRIT_PROTOCOL_START: Indicates user-space will start running
946 * new channel information (Channel Switch Announcement - CSA)
955 * @NL80211_CMD_VENDOR: Vendor-specified command/event. The command is specified
956 * by the %NL80211_ATTR_VENDOR_ID attribute and a sub-command in
959 * For feature advertisement, the %NL80211_ATTR_VENDOR_DATA attribute is
960 * used in the wiphy data as a nested attribute containing descriptions
964 * @NL80211_CMD_SET_QOS_MAP: Set Interworking QoS mapping for IP DSCP values.
966 * that attribute is not included, QoS mapping is disabled. Since this
976 * If the admitted time attribute is not added then the request just checks
992 * @NL80211_CMD_LEAVE_OCB: Leave the OCB network -- no special arguments, the
995 * @NL80211_CMD_TDLS_CHANNEL_SWITCH: Start channel-switching with a TDLS peer,
1000 * The driver is responsible for continually initiating channel-switching
1003 * @NL80211_CMD_TDLS_CANCEL_CHANNEL_SWITCH: Stop channel-switching with a TDLS
1008 * as an event to indicate changes for devices with wiphy-specific regdom
1011 * @NL80211_CMD_ABORT_SCAN: Stop an ongoing scan. Returns -ENOENT if a scan is
1020 * %NL80211_ATTR_NAN_MASTER_PREF attribute and optional
1022 * omitted or set to 0, it means don't-care and the device will
1028 * with %NL80211_ATTR_NAN_FUNC nested attribute. When called, this
1032 * Since instance ID's can be re-used, this cookie is the right
1051 * set to zero, the configuration is changed to don't-care
1054 * This will contain a %NL80211_ATTR_NAN_MATCH nested attribute and
1063 * @NL80211_CMD_SET_PMK: For offloaded 4-Way handshake, set the PMK or PMK-R0
1065 * When %NL80211_ATTR_PMKR0_NAME is set, %NL80211_ATTR_PMK specifies the
1066 * PMK-R0, otherwise it specifies the PMK.
1067 * @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
1102 * %NL80211_ATTR_STATUS_CODE attribute in %NL80211_CMD_EXTERNAL_AUTH
1115 * the %NL80211_ATTR_FTM_RESPONDER_STATS attribute.
1117 * @NL80211_CMD_PEER_MEASUREMENT_START: start a (set of) peer measurement(s)
1119 * %NL80211_ATTR_PEER_MEASUREMENTS attribute. Optionally, MAC address
1122 * If a timeout is requested, use the %NL80211_ATTR_TIMEOUT attribute.
1162 * Here attribute %NL80211_ATTR_MAC is used to specify connected mesh
1167 * is passed using %NL80211_ATTR_TID_CONFIG attribute.
1414 NL80211_CMD_MAX = __NL80211_CMD_AFTER_LAST - 1
1432 /* source-level API compatibility */
1438 * enum nl80211_attrs - nl80211 netlink attributes
1440 * @NL80211_ATTR_UNSPEC: unspecified attribute to catch errors
1448 * %NL80211_ATTR_WIPHY_CHANNEL_TYPE attribute or the attributes
1451 * @NL80211_ATTR_CHANNEL_WIDTH: u32 attribute containing one of the values
1462 * this attribute)
1466 * This attribute is now deprecated.
1475 * fragmentation with (u32)-1; dot11FragmentationThreshold; u32
1478 * 0..65536, disable with (u32)-1; dot11RTSThreshold; u32
1486 * @NL80211_ATTR_WDEV: wireless device identifier, used for pseudo-devices
1494 * @NL80211_ATTR_KEY_IDX: key ID (u8, 0-3)
1499 * @NL80211_ATTR_KEY_DEFAULT: Flag attribute indicating the key is default key
1500 * @NL80211_ATTR_KEY_DEFAULT_MGMT: Flag attribute indicating the key is the
1523 * given for %NL80211_CMD_GET_STATION, nested attribute containing
1529 * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
1534 * info given for %NL80211_CMD_GET_MPATH, nested attribute described at
1540 * @NL80211_ATTR_REG_ALPHA2: an ISO-3166-alpha2 country code for which the
1541 * current regulatory domain should be set to or is already set to.
1542 * For example, 'CR', for Costa Rica. This attribute is used by the kernel
1543 * to query the CRDA to retrieve one regulatory domain. This attribute can
1544 * also be used by userspace to query the kernel for the currently set
1546 * IEEE-802.11 country information element to identify a country.
1547 * Users can also simply ask the wireless core to set regulatory domain
1564 * @NL80211_ATTR_SUPPORTED_IFTYPES: nested attribute containing all
1565 * supported interface types, each a flag attribute with the number
1575 * a single scan request, a wiphy attribute.
1577 * scan with a single scheduled scan request, a wiphy attribute.
1583 * used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute.
1585 * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz)
1586 * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive
1587 * scanning and include a zero-length SSID (wildcard) for wildcard scan
1593 * set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*)
1595 * @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies
1599 * @NL80211_ATTR_FRAME: frame data (binary attribute), including frame header
1602 * @NL80211_ATTR_SSID: SSID (binary attribute, 0..32 octets)
1612 * due to considerations from a beacon hint. This attribute reflects
1614 * attributes consists of a nested attribute containing
1617 * due to considerations from a beacon hint. This attribute reflects
1619 * attributes consists of a nested attribute containing
1622 * @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported
1633 * this attribute can be used with %NL80211_CMD_ASSOCIATE and
1640 * @NL80211_ATTR_STA_FLAGS2: Attribute containing a
1649 * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
1653 * attribute is also used as a flag in the wiphy information to
1661 * socket. If this attribute is missing, then legacy behavior of sending
1666 * flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
1670 * We recommend using nested, driver-specific attributes within this.
1677 * @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating
1692 * This attribute is also sent in response to @NL80211_CMD_GET_WIPHY,
1706 * Reassociate Request frame (with the value of this attribute in the
1710 * @NL80211_ATTR_KEY: key information in a nested attribute with
1711 * %NL80211_KEY_* sub-attributes
1713 * and join_ibss(), key information is in a nested attribute each
1714 * with %NL80211_KEY_* sub-attributes
1726 * @NL80211_ATTR_4ADDR: Use 4-address frames on a virtual interface
1729 * the survey response for %NL80211_CMD_GET_SURVEY, nested attribute
1734 * cache, a wiphy attribute.
1737 * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that
1739 * remain-on-channel operation, in milliseconds, u32.
1741 * @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects.
1743 * @NL80211_ATTR_TX_RATES: Nested set of attributes
1747 * rates based on negotiated supported rates information. This attribute
1756 * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
1760 * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
1761 * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
1764 * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
1765 * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
1768 * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
1774 * nested attribute with %NL80211_ATTR_CQM_* sub-attributes.
1776 * @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command
1789 * for non-automatic settings.
1792 * means support for per-station GTKs.
1806 * Non-802.11n drivers can derive wether to use diversity or not.
1808 * support by returning -EINVAL.
1827 * flag isn't set, the frame will be rejected. This is also used as an
1832 * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
1833 * attributes, specifying what a key should be set as default as.
1838 * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
1858 * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more
1861 * pass-thru filter rules.
1863 * set. Since not every hardware supports matching all types of
1867 * Thus, the implementation is somewhat hardware-dependent, but
1869 * needs to handle all the non-filtered results anyway.
1873 * will never let it go through), -EINVAL may be returned.
1876 * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
1879 * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like
1884 * @NL80211_ATTR_REKEY_DATA: nested attribute containing the information
1888 * nested array attribute containing an entry for each band, with the entry
1906 * @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration
1914 * @NL80211_ATTR_PMKSA_CANDIDATE: Nested attribute containing the PMKSA caching
1920 * applications use this attribute.
1921 * This attribute is used with %NL80211_CMD_TRIGGER_SCAN and
1927 * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a
1938 * @NL80211_ATTR_DEVICE_AP_SME: This u32 attribute may be listed for devices
1940 * with support for the features listed in this attribute, see
1948 * @NL80211_ATTR_FEATURE_FLAGS: This u32 attribute contains flags from
1951 * requests while operating in AP-mode.
1952 * This attribute holds a bitmap of the supported protocols for
1956 * probe-response frame. The DA field in the 802.11 header is zero-ed out,
1964 * MCS rates, MAX-AMSDU, HT-20-40 and HT_CAP_SGI_40
1983 * @NL80211_ATTR_RX_SIGNAL_DBM: signal strength in dBm (as a 32-bit int);
1984 * this attribute is (depending on the driver capabilities) added to
1992 * a user. If set code could specify exactly what type of source
2001 * This contains the authentication frame body (non-IE and IE data),
2007 * Status code). However, those fields are included in the attribute data
2008 * for all authentication algorithms to keep the attribute definition
2023 * @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode
2027 * carried in a u32 attribute
2032 * @NL80211_ATTR_MAC_ACL_MAX: u32 attribute to advertise the maximum
2041 * 802.11-2012 8.4.2.29 for more information.
2043 * has set in the %NL80211_ATTR_EXT_CAPA value, for multibit fields.
2046 * the driver, e.g., to enable TDLS power save (PU-APSD).
2050 * and PU-APSD.
2053 * &enum nl80211_protocol_features, the attribute is a u32.
2055 * @NL80211_ATTR_SPLIT_WIPHY_DUMP: flag attribute, userspace supports
2076 * @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's
2078 * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
2081 * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
2112 * u8 attribute.
2114 * @NL80211_ATTR_VENDOR_ID: The vendor ID, either a 24-bit OUI or, if
2115 * %NL80211_VENDOR_ID_IS_LINUX is set, a special Linux ID (not used yet)
2116 * @NL80211_ATTR_VENDOR_SUBCMD: vendor sub-command
2118 * attribute is also used for vendor command feature advertisement
2123 * data is in the format defined for the payload of the QoS Map Set element
2124 * in IEEE Std 802.11-2012, 8.4.2.97.
2129 * @NL80211_ATTR_MAX_AP_ASSOC_STA: Device attribute that indicates how many
2138 * @NL80211_ATTR_MAX_CSA_COUNTERS: U8 attribute used to advertise the maximum
2144 * @NL80211_ATTR_SOCKET_OWNER: Flag attribute, if set during interface
2147 * If set during scheduled scan start then the new scan req will be
2150 * If set during configuration of regulatory indoor operation then the
2154 * If set during NAN interface creation, the interface will be destroyed
2157 * attribute, the notifications will be sent to the %NL80211_MCGRP_NAN
2159 * If set during %NL80211_CMD_ASSOCIATE or %NL80211_CMD_CONNECT the
2161 * If set during %NL80211_CMD_JOIN_IBSS the IBSS will be automatically
2163 * If set during %NL80211_CMD_JOIN_MESH the mesh setup will be
2165 * If set during %NL80211_CMD_START_AP the AP will be automatically
2168 * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is
2172 * shall support Radio Resource Measurements (11k). This attribute can be
2181 * association request. In addition, it must also set the RRM capability
2184 * @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout
2186 * %NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower
2190 * @NL80211_ATTR_TSID: a TSID value (u8 attribute)
2191 * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute)
2193 * (per second) (u16 attribute)
2202 * @NL80211_ATTR_WIPHY_SELF_MANAGED_REG: flag attribute indicating this device
2203 * is self-managing its regulatory information and any regulatory domain
2210 * least-significant bit of the first byte in the array, ie. bit index 0
2215 * returned along with other survey data. If set, @NL80211_CMD_GET_SURVEY
2224 * net-detect scan is started, counting from the moment the
2227 * @NL80211_ATTR_REG_INDOOR: flag attribute, if set indicates that the device
2231 * scheduled scan supported by the device (u32), a wiphy attribute.
2233 * a scan plan (u32), a wiphy attribute.
2235 * a scan plan (u32), a wiphy attribute.
2241 * Each scan plan is a nested attribute of &enum nl80211_sched_scan_plan.
2242 * @NL80211_ATTR_PBSS: flag attribute. If set it means operate
2246 * @NL80211_ATTR_BSS_SELECT: nested attribute for driver supporting the
2250 * it contains the behaviour-specific attribute containing the parameters for
2256 * @NL80211_ATTR_PAD: attribute used for padding for 64-bit alignment
2258 * @NL80211_ATTR_IFTYPE_EXT_CAPA: Nested attribute of the following attributes:
2263 * @NL80211_ATTR_MU_MIMO_GROUP_DATA: array of 24 bytes that defines a MU-MIMO
2267 * each bit represents a group and set to 1 for being a member in
2273 * This attribute is used only if all interfaces are in monitor mode.
2274 * Set this attribute in order to monitor packets using the given MU-MIMO
2276 * to turn off that feature set all the bits of the groupID to zero.
2278 * when using MU-MIMO air sniffer.
2279 * to turn that feature off set an invalid mac address
2285 * attribute must not be included).
2287 * %NL80211_ATTR_SCAN_START_TIME_TSF is set.
2289 * %NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY is not set, this is the
2290 * maximum measurement duration allowed. This attribute is used with
2293 * @NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY: flag attribute that indicates
2295 * mandatory. If this flag is not set, the duration is the maximum duration
2309 * would be set. This attribute is used with
2311 * it is optional. If no bands are set, it means don't-care and
2315 * attribute.
2316 * @NL80211_ATTR_NAN_MATCH: used to report a match. This is a nested attribute.
2321 * Request/Response frame protection. This attribute contains the 16 octet
2325 * packets should be send out as unicast to all stations (flag attribute).
2341 * better BSSs. The attribute value is a packed structure
2345 * u32 attribute with an &enum nl80211_timeout_reason value. This is used,
2348 * @NL80211_ATTR_FILS_ERP_USERNAME: EAP Re-authentication Protocol (ERP)
2352 * @NL80211_ATTR_FILS_ERP_REALM: EAP Re-authentication Protocol (ERP) realm part
2356 * @NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM: Unsigned 16-bit ERP next sequence number
2360 * @NL80211_ATTR_FILS_ERP_RRK: ERP re-authentication Root Key (rRK) for the
2366 * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertized by a FILS AP
2370 * @NL80211_ATTR_PMK: attribute for passing PMK key material. Used with
2373 * PSK for offloading 4-way handshake for WPA/WPA2-PSK networks. For 802.1X
2375 * support this attribute specifies the PMK-R0 if NL80211_ATTR_PMKR0_NAME
2378 * @NL80211_ATTR_SCHED_SCAN_MULTI: flag attribute which user-space shall use to
2383 * @NL80211_ATTR_WANT_1X_4WAY_HS: flag attribute which user-space can include
2385 * wants to use the supported offload of the 4-way handshake.
2386 * @NL80211_ATTR_PMKR0_NAME: PMK-R0 Name for offloaded FT.
2390 * authentication operation (u32 attribute with an
2393 * @NL80211_ATTR_EXTERNAL_AUTH_SUPPORT: Flag attribute indicating that the user
2394 * space supports external authentication. This attribute shall be used
2400 * u8 attribute. This is used with %NL80211_CMD_STA_OPMODE_CHANGED.
2402 * @NL80211_ATTR_TXQ_STATS: TXQ statistics (nested attribute, see &enum
2412 * association request when used with NL80211_CMD_NEW_STATION). Can be set
2413 * only if %NL80211_STA_FLAG_WME is set.
2415 * @NL80211_ATTR_FTM_RESPONDER: nested attribute which user-space can include
2420 * @NL80211_ATTR_FTM_RESPONDER_STATS: Nested attribute with FTM responder
2424 * if the attribute is not given no timeout is requested. Note that 0 is an
2431 * with the appropriate sub-attributes.
2440 * allows to set Tx power for a station. If this attribute is not included,
2441 * the default per-interface tx power setting will be overriding. Driver
2442 * should be picking up the lowest tx power, either tx power per-interface
2443 * or per-station.
2445 * @NL80211_ATTR_SAE_PASSWORD: attribute for passing SAE password material. It
2447 * SAE authentication for WPA3-Personal networks.
2451 * @NL80211_ATTR_HE_OBSS_PD: nested attribute for OBSS Packet Detection
2456 * Defined by IEEE P802.11ay/D4.0 section 9.4.2.251. (u8 attribute)
2458 * the allowed channel bandwidth configurations. (u8 attribute)
2464 * @NL80211_ATTR_HE_BSS_COLOR: nested attribute for BSS Color Settings.
2466 * @NL80211_ATTR_IFTYPE_AKM_SUITES: nested array attribute, with each entry
2468 * attribute is sent in a response to %NL80211_CMD_GET_WIPHY indicating
2474 * nested attribute with &enum nl80211_tid_config_attr sub-attributes;
2475 * on output (in wiphy attributes) it contains only the feature sub-
2511 * @NL80211_ATTR_SCAN_FREQ_KHZ: nested attribute with KHz frequencies
2517 * discovery. It is a nested attribute, see
2521 * unsolicited broadcast probe response. It is a nested attribute, see
2531 * @NL80211_ATTR_MAX: highest attribute number currently defined
3023 NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1
3026 /* source-level API compatibility */
3078 #define NL80211_SCAN_RSSI_THOLD_OFF -300
3083 * enum nl80211_iftype - (virtual) interface types
3090 * are a bit special in that they must always be tied to a pre-existing
3108 * to set the type of an interface.
3128 NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
3132 * enum nl80211_sta_flags - station flags
3137 * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
3144 * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should
3167 NL80211_STA_FLAG_MAX = __NL80211_STA_FLAG_AFTER_LAST - 1
3171 * enum nl80211_sta_p2p_ps_status - station support of P2P PS
3187 * struct nl80211_sta_flag_update - station flags mask/set
3188 * @mask: mask of station flags to set
3189 * @set: which values to set them to
3191 * Both mask and set contain bits as per &enum nl80211_sta_flags.
3195 __u32 set; member
3199 * enum nl80211_he_gi - HE guard interval
3211 * enum nl80211_he_ltf - HE long training field
3223 * enum nl80211_he_ru_alloc - HE RU allocation values
3224 * @NL80211_RATE_INFO_HE_RU_ALLOC_26: 26-tone RU allocation
3225 * @NL80211_RATE_INFO_HE_RU_ALLOC_52: 52-tone RU allocation
3226 * @NL80211_RATE_INFO_HE_RU_ALLOC_106: 106-tone RU allocation
3227 * @NL80211_RATE_INFO_HE_RU_ALLOC_242: 242-tone RU allocation
3228 * @NL80211_RATE_INFO_HE_RU_ALLOC_484: 484-tone RU allocation
3229 * @NL80211_RATE_INFO_HE_RU_ALLOC_996: 996-tone RU allocation
3230 * @NL80211_RATE_INFO_HE_RU_ALLOC_2x996: 2x996-tone RU allocation
3243 * enum nl80211_rate_info - bitrate information
3245 * These attribute types are used with %NL80211_STA_INFO_TXRATE
3248 * a 16-bit value, and new one that represents a 32-bit value.
3251 * (>6.5535Gbps) only 32-bit attribute is included.
3252 * User space tools encouraged to use the 32-bit attribute and fall
3253 * back to the 16-bit one for compatibility with older kernels.
3255 * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved
3265 * @NL80211_RATE_INFO_80P80_MHZ_WIDTH: unused - 80+80 is treated the
3268 * @NL80211_RATE_INFO_10_MHZ_WIDTH: 10 MHz width - note that this is
3271 * @NL80211_RATE_INFO_5_MHZ_WIDTH: 5 MHz width - note that this is
3274 * @NL80211_RATE_INFO_HE_MCS: HE MCS index (u8, 0-11)
3275 * @NL80211_RATE_INFO_HE_NSS: HE NSS value (u8, 1-8)
3280 * non-OFDMA was used (u8, see &enum nl80211_he_ru_alloc)
3305 NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1
3309 * enum nl80211_sta_bss_param - BSS information collected by STA
3311 * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM
3314 * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved
3335 NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1
3339 * enum nl80211_sta_info - station information
3341 * These attribute types are used with %NL80211_ATTR_STA_INFO
3344 * @__NL80211_STA_INFO_INVALID: attribute number 0 is reserved
3355 * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
3370 * attribute, like NL80211_STA_INFO_TX_BITRATE.
3371 * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
3377 * @NL80211_STA_INFO_LOCAL_PM: local mesh STA link-specific power mode
3378 * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode
3380 * non-peer STA
3381 * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
3383 * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
3392 * @NL80211_STA_INFO_TID_STATS: per-TID statistics (see &enum nl80211_tid_stats)
3393 * This is a nested attribute where each the inner attribute number is the
3394 * TID+1 and the special TID 16 (i.e. value 17) is used for non-QoS frames;
3399 * @NL80211_STA_INFO_PAD: attribute used for padding for 64-bit alignment
3408 * @NL80211_STA_INFO_CONNECTED_TO_GATE: set to true if STA has a path to a
3416 * @NL80211_STA_INFO_CONNECTED_TO_AS: set to true if STA has a path to a
3419 * @NL80211_STA_INFO_MAX: highest possible station info attribute
3473 NL80211_STA_INFO_MAX = __NL80211_STA_INFO_AFTER_LAST - 1
3476 /* we renamed this - stay compatible */
3481 * enum nl80211_tid_stats - per TID statistics attributes
3482 * @__NL80211_TID_STATS_INVALID: attribute number 0 is reserved
3490 * @NL80211_TID_STATS_PAD: attribute used for padding for 64-bit alignment
3491 * @NL80211_TID_STATS_TXQ_STATS: TXQ stats (nested attribute)
3493 * @NL80211_TID_STATS_MAX: highest numbered attribute here
3506 NL80211_TID_STATS_MAX = NUM_NL80211_TID_STATS - 1
3510 * enum nl80211_txq_stats - per TXQ statistics attributes
3511 * @__NL80211_TXQ_STATS_INVALID: attribute number 0 is reserved
3521 * (only for per-phy stats)
3526 * @NL80211_TXQ_STATS_MAX: highest numbered attribute here
3544 NL80211_TXQ_STATS_MAX = NUM_NL80211_TXQ_STATS - 1
3548 * enum nl80211_mpath_flags - nl80211 mesh path flags
3553 * @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set
3565 * enum nl80211_mpath_info - mesh path information
3567 * These attribute types are used with %NL80211_ATTR_MPATH_INFO when getting
3570 * @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
3581 * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
3599 NL80211_MPATH_INFO_MAX = __NL80211_MPATH_INFO_AFTER_LAST - 1
3603 * enum nl80211_band_iftype_attr - Interface type data attributes
3605 * @__NL80211_BAND_IFTYPE_ATTR_INVALID: attribute number 0 is reserved
3606 * @NL80211_BAND_IFTYPE_ATTR_IFTYPES: nested attribute containing a flag attribute
3616 * @NL80211_BAND_IFTYPE_ATTR_MAX: highest band HE capability attribute currently
3634 NL80211_BAND_IFTYPE_ATTR_MAX = __NL80211_BAND_IFTYPE_ATTR_AFTER_LAST - 1
3638 * enum nl80211_band_attr - band attributes
3639 * @__NL80211_BAND_ATTR_INVALID: attribute number 0 is reserved
3644 * @NL80211_BAND_ATTR_HT_MCS_SET: 16-byte attribute containing the MCS set as
3647 * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
3648 * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
3649 * @NL80211_BAND_ATTR_VHT_MCS_SET: 32-byte attribute containing the MCS set as
3652 * @NL80211_BAND_ATTR_IFTYPE_DATA: nested array attribute, with each entry using
3660 * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
3682 NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
3688 * enum nl80211_wmm_rule - regulatory wmm rule
3690 * @__NL80211_WMMR_INVALID: attribute number 0 is reserved
3707 NL80211_WMMR_MAX = __NL80211_WMMR_LAST - 1
3711 * enum nl80211_frequency_attr - frequency attributes
3712 * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
3727 * @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this
3739 * channel. A channel that has the INDOOR_ONLY attribute can only be
3747 * band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO or TDLS
3748 * off-channel on a channel that has the IR_CONCURRENT attribute set can be
3751 * off-channel while the device is also connected to an AP with DFS and
3752 * radar detection on the UNII band (it is up to user-space, i.e.,
3754 * attribute for IR is disallowed for master interfaces (IBSS, AP).
3760 * This is a nested attribute that contains the wmm limitation per AC.
3775 * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
3814 NL80211_FREQUENCY_ATTR_MAX = __NL80211_FREQUENCY_ATTR_AFTER_LAST - 1
3825 * enum nl80211_bitrate_attr - bitrate attributes
3826 * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
3830 * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
3841 NL80211_BITRATE_ATTR_MAX = __NL80211_BITRATE_ATTR_AFTER_LAST - 1
3845 * enum nl80211_initiator - Indicates the initiator of a reg domain request
3848 * @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the
3856 * structure passed by userspace (CRDA) from our wireless-regdb.
3858 * be disabled we disable the channel and re-enable it upon disassociation.
3868 * enum nl80211_reg_type - specifies the type of regulatory domain
3869 * @NL80211_REGDOM_TYPE_COUNTRY: the regulatory domain set is one that pertains
3870 * to a specific country. When this is set you can count on the
3872 * @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory
3874 * @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom
3875 * driver specific world regulatory domain. These do not apply system-wide
3878 * @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product
3879 * of an intersection between two regulatory domains -- the previously
3880 * set regulatory domain on the system and the last accepted regulatory
3891 * enum nl80211_reg_rule_attr - regulatory rule attributes
3892 * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
3893 * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
3911 * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
3930 NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
3934 * enum nl80211_sched_scan_match_attr - scheduled scan match attributes
3935 * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved
3941 * if this attribute is in a match set of its own, then it is treated as
3946 * attribute) is if there's only a single matchset with the RSSI attribute.
3951 * BSS-es in the specified band is to be adjusted before doing
3952 * RSSI-based BSS selection. The attribute value is a packed structure
3956 * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Nested attribute that carries the
3959 * band shall be encapsulated in attribute with type value equals to one
3962 * within an attribute of type NL80211_BAND_2GHZ. And one or more of such
3963 * attributes will be nested within this attribute.
3965 * attribute number currently defined
3981 __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1
3988 * enum nl80211_reg_rule_flags - regulatory rule flags
4004 * @NL80211_RRF_NO_HT40MINUS: channels can't be used in HT40- operation
4040 * enum nl80211_dfs_regions - regulatory DFS regions
4055 * enum nl80211_user_reg_hint_type - type of user regulatory hint
4058 * assumed if the attribute is not set.
4078 * enum nl80211_survey_info - survey information
4080 * These attribute types are used with %NL80211_ATTR_SURVEY_INFO
4083 * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
4099 * @NL80211_SURVEY_INFO_PAD: attribute used for padding for 64-bit alignment
4102 * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
4124 NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1
4135 * enum nl80211_mntr_flags - monitor configuration flags
4164 NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1
4168 * enum nl80211_mesh_power_mode - mesh power save modes
4171 * not known or has not been set yet.
4181 * @__NL80211_MESH_POWER_AFTER_LAST - internal use
4182 * @NL80211_MESH_POWER_MAX - highest possible power save level
4192 NL80211_MESH_POWER_MAX = __NL80211_MESH_POWER_AFTER_LAST - 1
4196 * enum nl80211_meshconf_params - mesh configuration parameters
4219 * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
4225 * set.
4251 * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
4265 * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding
4266 * or forwarding entity (default is TRUE - forwarding entity)
4276 * @NL80211_MESHCONF_HT_OPMODE: set mesh HT protection mode.
4278 * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
4298 * remove it from the STA's list of peers. You may set this to 0 to disable
4301 * @NL80211_MESHCONF_CONNECTED_TO_GATE: If set to true then this mesh STA
4306 * @NL80211_MESHCONF_NOLEARN: Try to avoid multi-hop path discovery (e.g.
4308 * this might not be the optimal decision as a multi-hop route might be
4312 * @NL80211_MESHCONF_CONNECTED_TO_AS: If set to true then this mesh STA
4354 NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1
4358 * enum nl80211_mesh_setup_params - mesh setup parameters
4384 * a userspace daemon. When this flag is set, the kernel will send peer
4402 * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
4419 NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1
4423 * enum nl80211_txq_attr - TX queue parameter attributes
4424 * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
4429 * 2^n-1 in the range 1..32767]
4431 * 2^n-1 in the range 1..32767]
4434 * @NL80211_TXQ_ATTR_MAX: Maximum TXQ attribute number
4446 NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1
4465 * enum nl80211_channel_type - channel type
4466 * @NL80211_CHAN_NO_HT: 20 MHz, non-HT channel
4481 * enum nl80211_key_mode - Key mode
4502 * enum nl80211_chan_width - channel width definitions
4505 * attribute.
4507 * @NL80211_CHAN_WIDTH_20_NOHT: 20 MHz, non-HT channel
4510 * attribute must be provided as well
4512 * attribute must be provided as well
4516 * attribute must be provided as well
4542 * enum nl80211_bss_scan_width - control channel width for a BSS
4544 * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute.
4561 * enum nl80211_bss - netlink attributes for a BSS
4572 * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
4574 * if the %NL80211_BSS_BEACON_IES attribute is present and the data is
4579 * If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the
4587 * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
4595 * @NL80211_BSS_TSF is known to be from a probe response (flag attribute)
4599 * @NL80211_BSS_PAD: attribute used for padding for 64-bit alignment
4605 * is set.
4606 * @NL80211_BSS_CHAIN_SIGNAL: per-chain signal strength of last BSS update.
4611 * @NL80211_BSS_MAX: highest BSS attribute
4638 NL80211_BSS_MAX = __NL80211_BSS_AFTER_LAST - 1
4642 * enum nl80211_bss_status - BSS "status"
4650 * The BSS status is a BSS attribute in scan dumps, which
4660 * enum nl80211_auth_type - AuthenticationType
4673 * trying multiple times); this is invalid in netlink -- leave out
4674 * the attribute for this on CONNECT commands.
4688 NL80211_AUTHTYPE_MAX = __NL80211_AUTHTYPE_NUM - 1,
4693 * enum nl80211_key_type - Key Type
4708 * enum nl80211_mfp - Management frame protection state
4726 * enum nl80211_key_default_types - key default types
4743 * enum nl80211_key_attributes - key attributes
4748 * @NL80211_KEY_IDX: key ID (u8, 0-3)
4758 * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
4759 * attributes, specifying what a key should be set as default as.
4766 * @NL80211_KEY_MAX: highest key attribute
4783 NL80211_KEY_MAX = __NL80211_KEY_AFTER_LAST - 1
4787 * enum nl80211_tx_rate_attributes - TX rate set attributes
4789 * @NL80211_TXRATE_LEGACY: Legacy (non-MCS) rates allowed for TX rate selection
4803 * @NL80211_TXRATE_MAX: highest TX rate attribute
4817 NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1
4824 * struct nl80211_txrate_vht - VHT MCS/NSS txrate bitmap
4833 * struct nl80211_txrate_he - HE MCS/NSS txrate bitmap
4847 * enum nl80211_band - Frequency band
4849 * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
4850 * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 69.12 GHz)
4851 * @NL80211_BAND_6GHZ: around 6 GHz band (5.9 - 7.2 GHz)
4867 * enum nl80211_ps_state - powersave state
4877 * enum nl80211_attr_cqm - connection quality monitor attributes
4882 * set, multiple values can be supplied as a low-to-high sorted array of
4901 * %NL80211_CMD_NOTIFY_CQM. Set to 0 to turn off TX error reporting.
4902 * @NL80211_ATTR_CQM_BEACON_LOSS_EVENT: flag attribute that's set in a beacon
4907 * @NL80211_ATTR_CQM_MAX: highest key attribute
4923 NL80211_ATTR_CQM_MAX = __NL80211_ATTR_CQM_AFTER_LAST - 1
4927 * enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
4942 * enum nl80211_tx_power_setting - TX power adjustment
4954 * enum nl80211_tid_config - TID config state
4963 /* enum nl80211_tx_rate_setting - TX rate configuration type
4974 /* enum nl80211_tid_config_attr - TID specific configuration.
4975 * @NL80211_TID_CONFIG_ATTR_PAD: pad attribute for 64-bit values
4977 * for per-vif configuration; doesn't list the ones that are generic
4979 * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
4981 * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if set indicates
4991 * transmission, user-space sets this configuration in
4993 * the max value is advertised by the driver in this attribute on
4996 * transmission, user-space sets this configuration in
4998 * the max value is advertised by the driver in this attribute on
5009 * @NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE: This attribute will be useful
5036 NL80211_TID_CONFIG_ATTR_MAX = __NL80211_TID_CONFIG_ATTR_AFTER_LAST - 1
5040 * enum nl80211_packet_pattern_attr - packet pattern attribute
5041 * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
5045 * a bit for each byte in the pattern. The lowest-order bit corresponds
5047 * in a little-endian-like format, i.e. the 9th byte of the pattern
5048 * corresponds to the lowest-order bit in the second byte of the mask.
5058 * @MAX_NL80211_PKTPAT: max attribute number
5067 MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
5071 * struct nl80211_pattern_support - packet pattern support information
5100 * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
5103 * the chip into a special state -- works best with chips that have
5104 * support for low-power operation already (flag)
5108 * is detected is implementation-specific (flag)
5112 * which are passed in an array of nested attributes, each nested attribute
5119 * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
5122 * When reporting wakeup. it is a u32 attribute containing the 0-based
5132 * @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag)
5138 * attribute contains the original length.
5141 * attribute if the packet was truncated somewhere.
5144 * be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN attribute
5148 * attribute if the packet was truncated somewhere.
5150 * "TCP connection wakeup" for more details. This is a nested attribute
5161 * is detected. This is a nested attribute that contains the
5166 * attribute is also sent in a response to
5169 * @NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS: nested attribute
5175 * Each element in the array is a nested attribute that contains
5176 * one optional %NL80211_ATTR_SSID attribute and one optional
5177 * %NL80211_ATTR_SCAN_FREQUENCIES attribute. At least one of
5183 * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
5212 MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1
5225 * optionally, a token from a list of tokens. This serves as a keep-alive
5228 * During this keep-alive period, the server doesn't send any data to the
5239 * struct nl80211_wowlan_tcp_data_seq - WoWLAN TCP data sequence
5253 * struct nl80211_wowlan_tcp_data_token - WoWLAN TCP data token config
5265 * struct nl80211_wowlan_tcp_data_token_feature - data token features
5275 * enum nl80211_wowlan_tcp_attrs - WoWLAN TCP connection parameters
5288 * For feature advertising, a u32 attribute holding the maximum length
5299 * u32 attribute holding the maximum length
5304 * @MAX_NL80211_WOWLAN_TCP: highest attribute number
5322 MAX_NL80211_WOWLAN_TCP = NUM_NL80211_WOWLAN_TCP - 1
5326 * struct nl80211_coalesce_rule_support - coalesce rule support information
5341 * enum nl80211_attr_coalesce_rule - coalesce rule attribute
5342 * @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute
5349 * @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number
5359 NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1
5363 * enum nl80211_coalesce_condition - coalesce rule conditions
5375 * enum nl80211_iface_limit_attrs - limit attributes
5378 * can be chosen from this set of interface types (u32)
5379 * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a
5380 * flag attribute for each interface type in this set
5382 * @MAX_NL80211_IFACE_LIMIT: highest attribute number
5391 MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1
5395 * enum nl80211_if_combination_attrs -- interface combination attributes
5400 * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of
5403 * in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE.
5404 * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that
5408 * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many
5410 * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap
5412 * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap
5414 * @NL80211_IFACE_COMB_BI_MIN_GCD: u32 attribute specifying the minimum GCD of
5418 * @MAX_NL80211_IFACE_COMB: highest attribute number
5424 * numbers = [ #{AP, P2P-GO} <= 8 ], BI min gcd, channels = 1, max = 8,
5430 * numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
5434 * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
5455 MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1
5460 * enum nl80211_plink_state - state of a mesh peer link finite state machine
5488 MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1
5492 * enum nl80211_plink_action - actions to perform in mesh peers
5515 * enum nl80211_rekey_data - attributes for GTK rekey offload
5522 * @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal)
5533 MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1
5537 * enum nl80211_hidden_ssid - values for %NL80211_ATTR_HIDDEN_SSID
5540 * @NL80211_HIDDEN_SSID_ZERO_LEN: hide SSID by using zero-length SSID element
5552 * enum nl80211_sta_wme_attr - station WME attributes
5553 * @__NL80211_STA_WME_INVALID: invalid number for nested attribute
5559 * @NL80211_STA_WME_MAX: highest station WME attribute
5568 NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1
5572 * enum nl80211_pmksa_candidate_attr - attributes for PMKSA caching candidates
5577 * @NL80211_PMKSA_CANDIDATE_PREAUTH: RSN pre-authentication supported (flag)
5580 * @MAX_NL80211_PMKSA_CANDIDATE: highest PMKSA caching candidate attribute
5591 MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1
5595 * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION
5611 * enum nl80211_ap_sme_features - device-integrated AP features
5619 * enum nl80211_feature_flags - device/driver features
5637 * @NL80211_FEATURE_VIF_TXPOWER: The driver supports per-vif TX power setting
5655 * stations the authenticated/associated bits have to be set in the mask.
5657 * (HT40, VHT 80/160 MHz) if this flag is set
5667 * channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
5670 * Set IE to probe requests.
5680 * estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used
5690 * TSPEC sessions (TID aka TSID 0-7) with the %NL80211_CMD_ADD_TX_TS
5692 * needs to be able to handle Block-Ack agreements and other things.
5700 * %NL80211_SCAN_FLAG_RANDOM_ADDR flag may be set for scans and the MAC
5705 * be set for scheduled scan and the MAC address mask/value will be used.
5709 * be set for scheduled scan and the MAC address mask/value will be used.
5747 * enum nl80211_ext_feature_index - bit index of extended features.
5751 * %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set
5754 * @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air
5757 * %NL80211_ATTR_MU_MIMO_GROUP_DATA attribute,
5759 * %NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR attribute.
5786 * %NL80211_ATTR_CQM_RSSI_THOLD attribute accepts a list of zero or more
5790 * @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK: Device wants to do 4-way
5793 * @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X: Device wants to do doing 4-way
5798 * the max channel attribute in the FILS request params IE with the
5812 * Device or driver will do all DFS-related actions by itself,
5813 * informing user-space about CAC progress, radar detection event,
5815 * No need to start CAC from user-space, no need to react to
5821 * @NL80211_EXT_FEATURE_TXQS: Driver supports FQ-CoDel-enabled intermediate
5832 * able to rekey an in-use key correctly. Userspace must not rekey PTK keys
5833 * if this flag is not set. Ignoring this can leak clear text packets and/or
5836 * Individually Addressed Frames" from IEEE802.11-2016.
5843 * (set/del PMKSA operations) in AP mode.
5855 * with VLAN tagged frames and separate VLAN-specific netdevs added using
5890 * @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK: Device wants to do 4-way
5935 /* we renamed this - stay compatible */
5966 MAX_NL80211_EXT_FEATURES = NUM_NL80211_EXT_FEATURES - 1
5970 * enum nl80211_probe_resp_offload_support_attr - optional supported
5971 * protocols for probe-response offloading by the driver/FW.
5972 * To be used with the %NL80211_ATTR_PROBE_RESP_OFFLOAD attribute.
5974 * protocols. Typically a subset of probe-requests belonging to a
5991 * enum nl80211_connect_failed_reason - connection request failed reasons
6002 * enum nl80211_timeout_reason - timeout reasons
6017 * enum nl80211_scan_flags - scan request control flags
6030 * as AP and the beaconing has already been configured. This attribute is
6032 * will be lost while scanning off-channel, therefore it must be used only
6036 * flag is set, depending on device capabilities the @NL80211_ATTR_MAC and
6050 * tx deferral (dot11FILSProbeDelay shall be set to 15ms)
6053 * a suitable candidate for (re-)association - suitable in terms of
6099 * enum nl80211_acl_policy - access control policy
6101 * Access control policy is applied on a MAC list set by
6117 * enum nl80211_smps_mode - SMPS mode
6132 NL80211_SMPS_MAX = __NL80211_SMPS_AFTER_LAST - 1
6136 * enum nl80211_radar_event - type of radar event for DFS operation
6147 * @NL80211_RADAR_NOP_FINISHED: The Non-Occupancy Period for this channel is
6150 * non-operating channel is expired and no longer valid. New CAC must
6152 * applicable for ETSI dfs domain where pre-CAC is valid for ever.
6166 * enum nl80211_dfs_state - DFS states for channels
6183 * enum nl80211_protocol_features - nl80211 protocol features
6185 * wiphy dumps (if requested by the application with the attribute
6195 * enum nl80211_crit_proto_id - nl80211 critical protocol identifiers
6216 * enum nl80211_rxmgmt_flags - flags for received management frame.
6232 * If this flag is unset, the lower 24 bits are an OUI, if set
6239 * struct nl80211_vendor_cmd_info - vendor command data
6241 * value is a 24-bit OUI; if it is set then a separately allocated ID
6244 * @subcmd: sub-command ID for the command
6252 * enum nl80211_tdls_peer_capability - TDLS peer flags.
6268 * enum nl80211_sched_scan_plan - scanning plan for scheduled scan
6269 * @__NL80211_SCHED_SCAN_PLAN_INVALID: attribute number 0 is reserved
6273 * scan plan (u32). The last scan plan must not specify this attribute
6276 * @NL80211_SCHED_SCAN_PLAN_MAX: highest scheduled scan plan attribute number
6288 __NL80211_SCHED_SCAN_PLAN_AFTER_LAST - 1
6292 * struct nl80211_bss_select_rssi_adjust - RSSI adjustment parameters.
6304 * enum nl80211_bss_select_attr - attributes for bss selection.
6307 * @NL80211_BSS_SELECT_ATTR_RSSI: Flag indicating only RSSI-based BSS selection
6309 * @NL80211_BSS_SELECT_ATTR_BAND_PREF: attribute indicating BSS
6311 * When there are multiple BSS-es in the preferred band, the driver
6312 * shall use RSSI-based BSS selection as a second step. The value of
6313 * this attribute is according to &enum nl80211_band (u32).
6315 * BSS-es in the specified band is to be adjusted before doing
6316 * RSSI-based BSS selection. The attribute value is a packed structure
6318 * @NL80211_BSS_SELECT_ATTR_MAX: highest bss select attribute number.
6333 NL80211_BSS_SELECT_ATTR_MAX = __NL80211_BSS_SELECT_ATTR_AFTER_LAST - 1
6337 * enum nl80211_nan_function_type - NAN function type
6343 * @NL80211_NAN_FUNC_FOLLOW_UP: function is follow-up
6352 NL80211_NAN_FUNC_MAX_TYPE = __NL80211_NAN_FUNC_TYPE_AFTER_LAST - 1,
6356 * enum nl80211_nan_publish_type - NAN publish tx type
6369 * enum nl80211_nan_func_term_reason - NAN functions termination reason
6388 * enum nl80211_nan_func_attributes - NAN function attributes
6392 * specified in NAN spec. This is a binary attribute.
6407 * follow up Service Discovery Frame. This is a binary attribute.
6414 * specific info. This is a binary attribute.
6415 * @NL80211_NAN_FUNC_SRF: Service Receive Filter. This is a nested attribute.
6418 * attribute. It is a list of binary values.
6420 * nested attribute. It is a list of binary values.
6427 * @NL80211_NAN_FUNC_ATTR_MAX: highest NAN function attribute
6450 NL80211_NAN_FUNC_ATTR_MAX = NUM_NL80211_NAN_FUNC_ATTR - 1
6454 * enum nl80211_nan_srf_attributes - NAN Service Response filter attributes
6456 * @NL80211_NAN_SRF_INCLUDE: present if the include bit of the SRF set.
6459 * %NL80211_NAN_SRF_MAC_ADDRS isn't present. This attribute is binary.
6464 * attribute. Each nested attribute is a MAC address.
6466 * @NL80211_NAN_SRF_ATTR_MAX: highest NAN SRF attribute
6477 NL80211_NAN_SRF_ATTR_MAX = NUM_NL80211_NAN_SRF_ATTR - 1,
6481 * enum nl80211_nan_match_attributes - NAN match attributes
6484 * match. This is a nested attribute.
6487 * that caused the match. This is a nested attribute.
6491 * @NL80211_NAN_MATCH_ATTR_MAX: highest NAN match attribute
6500 NL80211_NAN_MATCH_ATTR_MAX = NUM_NL80211_NAN_MATCH_ATTR - 1
6504 * nl80211_external_auth_action - Action to perform with external
6515 * enum nl80211_ftm_responder_attributes - fine timing measurement
6520 * (9.4.2.22 in 802.11-2016) with type 8 - LCI (9.4.2.22.10),
6523 * (9.4.2.22 in 802.11-2016) with type 11 - Civic (Section 9.4.2.22.13),
6526 * @NL80211_FTM_RESP_ATTR_MAX: highest FTM responder attribute.
6537 NL80211_FTM_RESP_ATTR_MAX = __NL80211_FTM_RESP_ATTR_LAST - 1,
6541 * enum nl80211_ftm_responder_stats - FTM responder statistics
6543 * These attribute types are used with %NL80211_ATTR_FTM_RESPONDER_STATS
6546 * @__NL80211_FTM_STATS_INVALID: attribute number 0 is reserved
6553 * @NL80211_FTM_STATS_NON_ASAP_NUM: number of non-ASAP sessions (u32)
6554 * @NL80211_FTM_STATS_TOTAL_DURATION_MSEC: total sessions durations - gives an
6556 * @NL80211_FTM_STATS_UNKNOWN_TRIGGERS_NUM: number of unknown FTM triggers -
6560 * - initiator asks for a new scheduling although it already has scheduled
6566 * @NL80211_FTM_STATS_MAX: highest possible FTM responder stats attribute
6583 NL80211_FTM_STATS_MAX = __NL80211_FTM_STATS_AFTER_LAST - 1
6587 * enum nl80211_preamble - frame preamble types
6603 * enum nl80211_peer_measurement_type - peer measurement types
6618 NL80211_PMSR_TYPE_MAX = NUM_NL80211_PMSR_TYPES - 1
6622 * enum nl80211_peer_measurement_status - peer measurement status
6626 * @NL80211_PMSR_STATUS_FAILURE: measurement failed, a type-dependent
6637 * enum nl80211_peer_measurement_req - peer measurement request attributes
6640 * @NL80211_PMSR_REQ_ATTR_DATA: This is a nested attribute with measurement
6641 * type-specific request data inside. The attributes used are from the
6644 * (flag attribute)
6647 * @NL80211_PMSR_REQ_ATTR_MAX: highest attribute number
6657 NL80211_PMSR_REQ_ATTR_MAX = NUM_NL80211_PMSR_REQ_ATTRS - 1
6661 * enum nl80211_peer_measurement_resp - peer measurement response attributes
6664 * @NL80211_PMSR_RESP_ATTR_DATA: This is a nested attribute with measurement
6665 * type-specific results inside. The attributes used are from the enums
6677 * (*e.g. with FTM per-burst data) this flag will be cleared on all but
6678 * the last result; if all results are combined it's set on the single
6680 * @NL80211_PMSR_RESP_ATTR_PAD: padding for 64-bit attributes, ignore
6683 * @NL80211_PMSR_RESP_ATTR_MAX: highest attribute number
6697 NL80211_PMSR_RESP_ATTR_MAX = NUM_NL80211_PMSR_RESP_ATTRS - 1
6701 * enum nl80211_peer_measurement_peer_attrs - peer attributes for measurement
6705 * @NL80211_PMSR_PEER_ATTR_CHAN: channel definition, nested, using top-level
6707 * @NL80211_PMSR_PEER_ATTR_REQ: This is a nested attribute indexed by
6710 * @NL80211_PMSR_PEER_ATTR_RESP: This is a nested attribute indexed by
6715 * @NL80211_PMSR_PEER_ATTR_MAX: highest attribute number
6727 NL80211_PMSR_PEER_ATTR_MAX = NUM_NL80211_PMSR_PEER_ATTRS - 1,
6731 * enum nl80211_peer_measurement_attrs - peer measurement attributes
6734 * @NL80211_PMSR_ATTR_MAX_PEERS: u32 attribute used for capability
6737 * @NL80211_PMSR_ATTR_REPORT_AP_TSF: flag attribute in capability
6740 * @NL80211_PMSR_ATTR_RANDOMIZE_MAC_ADDR: flag attribute in capability
6744 * type-specific capabilities inside, which are from the enums
6746 * @NL80211_PMSR_ATTR_PEERS: nested attribute, the nesting index is
6748 * sub-attributes taken from
6752 * @NL80211_PMSR_ATTR_MAX: highest attribute number
6765 NL80211_PMSR_ATTR_MAX = NUM_NL80211_PMSR_ATTR - 1
6769 * enum nl80211_peer_measurement_ftm_capa - FTM capabilities
6772 * @NL80211_PMSR_FTM_CAPA_ATTR_ASAP: flag attribute indicating ASAP mode
6774 * @NL80211_PMSR_FTM_CAPA_ATTR_NON_ASAP: flag attribute indicating non-ASAP
6776 * @NL80211_PMSR_FTM_CAPA_ATTR_REQ_LCI: flag attribute indicating if LCI
6778 * @NL80211_PMSR_FTM_CAPA_ATTR_REQ_CIVICLOC: flag attribute indicating if civic
6780 * @NL80211_PMSR_FTM_CAPA_ATTR_PREAMBLES: u32 bitmap attribute of bits
6787 * @NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT: u32 attribute indicating
6790 * @NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST: u32 attribute indicating
6792 * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
6794 * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
6798 * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
6816 NL80211_PMSR_FTM_CAPA_ATTR_MAX = NUM_NL80211_PMSR_FTM_CAPA_ATTR - 1
6820 * enum nl80211_peer_measurement_ftm_req - FTM request attributes
6827 * 802.11-2016 9.4.2.168 "Fine Timing Measurement Parameters element"
6828 * (u8, 0-15, optional with default 15 i.e. "no preference")
6831 * @NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION: burst duration, as in 802.11-2016
6832 * Table 9-257 "Burst Duration field encoding" (u8, 0-15, optional with
6836 * (u8, 0-31, optional with default 0 i.e. "no preference")
6844 * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED are
6847 * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
6851 * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
6854 * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
6858 * @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
6877 NL80211_PMSR_FTM_REQ_ATTR_MAX = NUM_NL80211_PMSR_FTM_REQ_ATTR - 1
6881 * enum nl80211_peer_measurement_ftm_failure_reasons - FTM failure reasons
6908 * enum nl80211_peer_measurement_ftm_resp - FTM response attributes
6911 * @NL80211_PMSR_FTM_RESP_ATTR_FAIL_REASON: FTM-specific failure reason
6914 * as separate results then it will be the burst index 0...(N-1) and
6949 * this is the contents of the Measurement Report Element (802.11-2016
6954 * this is the contents of the Measurement Report Element (802.11-2016
6960 * @NL80211_PMSR_FTM_RESP_ATTR_MAX: highest attribute number
6989 NL80211_PMSR_FTM_RESP_ATTR_MAX = NUM_NL80211_PMSR_FTM_RESP_ATTR - 1
6993 * enum nl80211_obss_pd_attributes - OBSS packet detection attributes
6998 * @NL80211_HE_OBSS_PD_ATTR_NON_SRG_MAX_OFFSET: the non-SRG OBSS PD maximum
7007 * @NL80211_HE_OBSS_PD_ATTR_MAX: highest OBSS PD attribute.
7021 NL80211_HE_OBSS_PD_ATTR_MAX = __NL80211_HE_OBSS_PD_ATTR_LAST - 1,
7025 * enum nl80211_bss_color_attributes - BSS Color attributes
7033 * @NL80211_HE_BSS_COLOR_ATTR_MAX: highest BSS Color attribute.
7044 NL80211_HE_BSS_COLOR_ATTR_MAX = __NL80211_HE_BSS_COLOR_ATTR_LAST - 1,
7048 * enum nl80211_iftype_akm_attributes - interface type AKM attributes
7051 * @NL80211_IFTYPE_AKM_ATTR_IFTYPES: nested attribute containing a flag
7052 * attribute for each interface type that supports AKM suites specified in
7058 * @NL80211_IFTYPE_AKM_ATTR_MAX: highest interface type AKM attribute.
7068 NL80211_IFTYPE_AKM_ATTR_MAX = __NL80211_IFTYPE_AKM_ATTR_LAST - 1,
7072 * enum nl80211_fils_discovery_attributes - FILS discovery configuration
7073 * from IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
7085 * @NL80211_FILS_DISCOVERY_ATTR_MAX: highest attribute
7096 NL80211_FILS_DISCOVERY_ATTR_MAX = __NL80211_FILS_DISCOVERY_ATTR_LAST - 1
7106 * enum nl80211_unsol_bcast_probe_resp_attributes - Unsolicited broadcast probe
7118 * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX: highest attribute
7129 __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST - 1