Lines Matching +full:power +full:- +full:monitor
3 Contact: linux-scsi@vger.kernel.org
5 This file contains the auto-hibernate idle timer setting of a
6 UFS host controller. A value of '0' means auto-hibernate is not
9 the link into hibernate state. That will save power at the
11 10-bit values with a power-of-ten multiplier which allows a
104 Description: This file shows value that defines the power mode after
273 written during the pre-soldering phase of the PSA flow.
307 Description: This file shows the MIPI M-PHY version number in BCD format.
395 Description: This file shows the maximum data-in buffer size. This
406 Description: This file shows the maximum data-out buffer size. This
439 Description: This file shows support for out-of-order data transfer.
507 enhanced type 1-4). This is one of the UFS geometry
519 enhanced type 1-4). This is one of the UFS geometry
566 power descriptor parameters. The full information about
669 Description: This file defines the device behavior when a power failure
766 logical units configured as power on write protected. The
837 Description: This file provides the current power mode UFS device attribute.
976 load to all logical units in pre-soldering state.
999 runtime power management level. The current driver
1025 Description: This entry shows the target power mode of an UFS device
1026 for the chosen runtime power management level.
1035 for the chosen runtime power management level.
1044 system power management level. The current driver
1070 Description: This entry shows the target power mode of an UFS device
1071 for the chosen system power management level.
1080 for the chosen system power management level.
1084 What: /sys/bus/platform/drivers/ufshcd/*/monitor/monitor_enable
1085 What: /sys/bus/platform/devices/*.ufs/monitor/monitor_enable
1088 Description: This file shows the status of performance monitor enablement
1089 and it can be used to start/stop the monitor. When the monitor
1092 What: /sys/bus/platform/drivers/ufshcd/*/monitor/monitor_chunk_size
1093 What: /sys/bus/platform/devices/*.ufs/monitor/monitor_chunk_size
1096 Description: This file tells the monitor to focus on requests transferring
1098 It can only be changed when monitor is disabled.
1100 What: /sys/bus/platform/drivers/ufshcd/*/monitor/read_total_sectors
1101 What: /sys/bus/platform/devices/*.ufs/monitor/read_total_sectors
1105 sent from device to host after monitor gets started.
1109 What: /sys/bus/platform/drivers/ufshcd/*/monitor/read_total_busy
1110 What: /sys/bus/platform/devices/*.ufs/monitor/read_total_busy
1114 sending data from device to host after monitor gets started.
1118 What: /sys/bus/platform/drivers/ufshcd/*/monitor/read_nr_requests
1119 What: /sys/bus/platform/devices/*.ufs/monitor/read_nr_requests
1123 monitor gets started.
1127 What: /sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_max
1128 What: /sys/bus/platform/devices/*.ufs/monitor/read_req_latency_max
1132 read requests after monitor gets started.
1136 What: /sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_min
1137 What: /sys/bus/platform/devices/*.ufs/monitor/read_req_latency_min
1141 read requests after monitor gets started.
1145 What: /sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_avg
1146 What: /sys/bus/platform/devices/*.ufs/monitor/read_req_latency_avg
1150 read requests after monitor gets started.
1154 What: /sys/bus/platform/drivers/ufshcd/*/monitor/read_req_latency_sum
1155 What: /sys/bus/platform/devices/*.ufs/monitor/read_req_latency_sum
1159 read requests sent after monitor gets started.
1163 What: /sys/bus/platform/drivers/ufshcd/*/monitor/write_total_sectors
1164 What: /sys/bus/platform/devices/*.ufs/monitor/write_total_sectors
1168 from host to device after monitor gets started.
1172 What: /sys/bus/platform/drivers/ufshcd/*/monitor/write_total_busy
1173 What: /sys/bus/platform/devices/*.ufs/monitor/write_total_busy
1177 sending data from host to device after monitor gets started.
1181 What: /sys/bus/platform/drivers/ufshcd/*/monitor/write_nr_requests
1182 What: /sys/bus/platform/devices/*.ufs/monitor/write_nr_requests
1186 monitor gets started.
1190 What: /sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_max
1191 What: /sys/bus/platform/devices/*.ufs/monitor/write_req_latency_max
1195 requests after monitor gets started.
1199 What: /sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_min
1200 What: /sys/bus/platform/devices/*.ufs/monitor/write_req_latency_min
1204 requests after monitor gets started.
1208 What: /sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_avg
1209 What: /sys/bus/platform/devices/*.ufs/monitor/write_req_latency_avg
1213 requests after monitor gets started.
1217 What: /sys/bus/platform/drivers/ufshcd/*/monitor/write_req_latency_sum
1218 What: /sys/bus/platform/devices/*.ufs/monitor/write_req_latency_sum
1222 requests after monitor gets started.
1230 Description: This entry shows if preserve user-space was configured
1255 Description: This entry shows the total user-space decrease in shared
1393 01h 0% - 10% WriteBooster Buffer life time used
1395 0Ah 90% - 100% WriteBooster Buffer life time used
1414 enable it. The WriteBooster is enabled after power-on/reset,
1423 Contact: Jinyoung Choi <j-young.choi@samsung.com>
1445 host-device pair. i.e. the capabilities which are enabled in the