Searched full:pin9 (Results 1 – 13 of 13) sorted by relevance
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/sound/ |
| D | everest,es8326.yaml | 66 Bit(3) 1 means PIN9 is the irq source for jack detection. When set to 0,
67 bias change on PIN9 do not triggers irq.
69 Bit(5) 1 means PIN9 is the irq source after MIC detect.
|
| /kernel/linux/linux-6.6/arch/arm64/boot/dts/renesas/ |
| D | r8a779g0-white-hawk-ard-audio-da7212.dtso | 22 * | SSI_SCK_V pin9 |<----->| pin1 BCLK |
36 * | 3v3 (v) pin9 |<----->| pin4 / pin8 3.3v |
|
| /kernel/linux/linux-5.10/drivers/net/wireless/microchip/wilc1000/ |
| D | Kconfig | 22 To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
| /kernel/linux/linux-6.6/drivers/net/wireless/microchip/wilc1000/ |
| D | Kconfig | 22 To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/nuvoton/ |
| D | nuvoton-npcm750-pincfg-evb.dtsi | 11 pin9_output_high: pin9-output-high {
|
| /kernel/linux/linux-5.10/drivers/media/pci/ttpci/ |
| D | av7110_v4l.c | 256 saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTHI); // TDA9819 pin9(STD) in av7110_dvb_c_switch()
292 saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTLO); // TDA9819 pin9(STD) in av7110_dvb_c_switch()
745 saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTLO); // TDA9819 pin9(STD) in av7110_init_analog_module()
|
| D | av7110.c | 2227 saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTLO); // TDA9819 pin9(STD) in frontend_init()
|
| /kernel/linux/linux-6.6/drivers/staging/media/av7110/ |
| D | av7110_v4l.c | 245 saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTHI); // TDA9819 pin9(STD) in av7110_dvb_c_switch()
281 saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTLO); // TDA9819 pin9(STD) in av7110_dvb_c_switch()
750 saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTLO); // TDA9819 pin9(STD) in av7110_init_analog_module()
|
| D | av7110.c | 2230 saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTLO); // TDA9819 pin9(STD) in frontend_init()
|
| /kernel/linux/linux-6.6/arch/arm/boot/dts/ti/omap/ |
| D | am43x-epos-evm.dts | 71 col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */
|
| /kernel/linux/linux-5.10/arch/arm/boot/dts/ |
| D | am43x-epos-evm.dts | 71 col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */
|
| /kernel/linux/linux-5.10/drivers/pinctrl/zte/ |
| D | pinctrl-zx296718.c | 272 AON_MUX(0x2, "nonAON"), /* pin9 */
|
| /kernel/linux/linux-6.6/drivers/hwmon/ |
| D | adt7475.c | 1530 prop2 = "adi,pin9-function"; in load_config()
|