Home
last modified time | relevance | path

Searched +full:imx8mp +full:- +full:dwc3 (Results 1 – 6 of 6) sorted by relevance

/kernel/linux/linux-6.6/drivers/usb/dwc3/
Ddwc3-imx8mp.c1 // SPDX-License-Identifier: GPL-2.0
3 * dwc3-imx8mp.c - NXP imx8mp Specific Glue layer
44 #define USB_CTRL0_PORTPWR_EN BIT(12) /* 1 - PPC enabled (default) */
45 #define USB_CTRL0_USB3_FIXED BIT(22) /* 1 - USB3 permanent attached */
46 #define USB_CTRL0_USB2_FIXED BIT(23) /* 1 - USB2 permanent attached */
48 #define USB_CTRL1_OC_POLARITY BIT(16) /* 0 - HIGH / 1 - LOW */
49 #define USB_CTRL1_PWR_POLARITY BIT(17) /* 0 - HIGH / 1 - LOW */
53 struct platform_device *dwc3; member
65 struct device *dev = dwc3_imx->dev; in imx8mp_configure_glue()
68 if (!dwc3_imx->glue_base) in imx8mp_configure_glue()
[all …]
DMakefile1 # SPDX-License-Identifier: GPL-2.0
3 CFLAGS_trace.o := -I$(src)
5 obj-$(CONFIG_USB_DWC3) += dwc3.o
7 dwc3-y := core.o
10 dwc3-y += trace.o
14 dwc3-y += host.o
18 dwc3-y += gadget.o ep0.o
22 dwc3-y += drd.o
26 dwc3-y += ulpi.o
30 dwc3-y += debugfs.o
[all …]
DKconfig1 # SPDX-License-Identifier: GPL-2.0
14 module, the module will be called dwc3.ko.
22 Select this if you have ULPI type PHY attached to your DWC3
26 bool "DWC3 Mode Selection"
35 Select this when you want to use DWC3 in host mode only,
42 Select this when you want to use DWC3 in gadget mode only,
49 This is the default mode of working of DWC3 controller where
78 tristate "PCIe-based Platforms"
86 tristate "Synopsys PCIe-based HAPS Platforms"
144 tristate "NXP iMX8MP Platform"
/kernel/linux/linux-6.6/Documentation/devicetree/bindings/usb/
Dfsl,imx8mp-dwc3.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/usb/fsl,imx8mp-dwc3.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: NXP iMX8MP Soc USB Controller
11 - Li Jun <jun.li@nxp.com>
15 const: fsl,imx8mp-dwc3
19 - description: Address and length of the register set for HSIO Block Control
20 - description: Address and length of the register set for the wrapper of dwc3 core on the SOC.
22 "#address-cells":
[all …]
/kernel/linux/linux-6.6/arch/arm64/boot/dts/freescale/
Dimx8mp.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 #include <dt-bindings/clock/imx8mp-clock.h>
7 #include <dt-bindings/power/imx8mp-power.h>
8 #include <dt-bindings/reset/imx8mp-reset.h>
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/interconnect/fsl,imx8mp.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
13 #include <dt-bindings/thermal/thermal.h>
15 #include "imx8mp-pinfunc.h"
[all …]
/kernel/linux/patches/linux-5.10/imx8mm_patch/patches/drivers/
D0034_linux_drivers_usb_vfio_wdt_tty_uio.patch7 Change-Id: I1b7e905c318654a235ffe85d3c392289593c1c9d
9 diff --git a/drivers/Kconfig b/drivers/Kconfig
11 --- a/drivers/Kconfig
13 @@ -238,6 +238,8 @@ source "drivers/counter/Kconfig"
22 diff --git a/drivers/Makefile b/drivers/Makefile
24 --- a/drivers/Makefile
26 @@ -192,5 +192,6 @@ obj-$(CONFIG_GNSS) += gnss/
27 obj-$(CONFIG_INTERCONNECT) += interconnect/
28 obj-$(CONFIG_COUNTER) += counter/
29 obj-$(CONFIG_MOST) += most/
[all …]