Searched full:pulsed (Results 1 – 25 of 29) sorted by relevance
12
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/watchdog/ |
| D | kontron,sl28cpld-wdt.yaml | 28 property is set, this output will be pulsed when the watchdog bites
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/watchdog/ |
| D | kontron,sl28cpld-wdt.yaml | 28 property is set, this output will be pulsed when the watchdog bites
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/gpio/ |
| D | gpio-pisosr.txt | 16 pin is pulsed before reading from the device to
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/gpio/ |
| D | gpio-pisosr.txt | 16 pin is pulsed before reading from the device to
|
| /kernel/linux/linux-5.10/drivers/media/dvb-frontends/ |
| D | lnbp21.h | 35 0=pulsed (dynamic) curr limiting
|
| D | stv0910.c | 1095 * Note: The bit is only pulsed -> no lock on shared register needed in start()
|
| /kernel/linux/linux-6.6/drivers/media/dvb-frontends/ |
| D | lnbp21.h | 35 0=pulsed (dynamic) curr limiting
|
| D | stv0910.c | 1086 * Note: The bit is only pulsed -> no lock on shared register needed in start()
|
| /kernel/linux/linux-5.10/drivers/iio/chemical/ |
| D | Kconfig | 73 iAQ-Core Continuous/Pulsed VOC (Volatile Organic Compounds)
|
| /kernel/linux/linux-6.6/drivers/iio/chemical/ |
| D | Kconfig | 73 iAQ-Core Continuous/Pulsed VOC (Volatile Organic Compounds)
|
| /kernel/linux/linux-6.6/drivers/rtc/ |
| D | rtc-ab-b5ze-s3.c | 88 #define ABB5ZES3_REG_TIM_CLK_TAM BIT(7) /* Permanent/pulsed timer A/int. 2 */
89 #define ABB5ZES3_REG_TIM_CLK_TBM BIT(6) /* Permanent/pulsed timer B */
617 * pulsed). in abb5zes3_rtc_check_setup()
|
| /kernel/linux/linux-5.10/drivers/rtc/ |
| D | rtc-ab-b5ze-s3.c | 88 #define ABB5ZES3_REG_TIM_CLK_TAM BIT(7) /* Permanent/pulsed timer A/int. 2 */
89 #define ABB5ZES3_REG_TIM_CLK_TBM BIT(6) /* Permanent/pulsed timer B */
617 * pulsed). in abb5zes3_rtc_check_setup()
|
| /kernel/linux/linux-6.6/Documentation/driver-api/ |
| D | reset.rst | 122 driver is probed or resumed to share a pulsed reset line.
|
| D | pin-control.rst | 809 pulsed out. It is likely possible to disrupt the traffic on the pin by doing
|
| /kernel/linux/linux-6.6/drivers/comedi/drivers/ |
| D | z8536.h | 145 #define Z8536_PAB_HANDSHAKE_HST_PULSED Z8536_PAB_HANDSHAKE_HST(2)/* Pulsed */
|
| /kernel/linux/linux-5.10/drivers/staging/comedi/drivers/ |
| D | z8536.h | 145 #define Z8536_PAB_HANDSHAKE_HST_PULSED Z8536_PAB_HANDSHAKE_HST(2)/* Pulsed */
|
| /kernel/linux/linux-6.6/sound/soc/codecs/ |
| D | ssm3515.c | 278 * what the datasheet calls 'Pulsed FSYNC mode' and '50% in ssm3515_set_fmt()
|
| /kernel/linux/linux-5.10/drivers/media/pci/saa7134/ |
| D | saa7134-input.c | 181 /* GPIO&0x40 is pulsed low when a button is pressed. Don't do in get_key_msi_tvanywhere_plus()
233 /* GPIO&0x100 is pulsed low when a button is pressed. Don't do in get_key_kworld_pc150u()
|
| /kernel/linux/linux-6.6/drivers/media/pci/saa7134/ |
| D | saa7134-input.c | 181 /* GPIO&0x40 is pulsed low when a button is pressed. Don't do in get_key_msi_tvanywhere_plus()
233 /* GPIO&0x100 is pulsed low when a button is pressed. Don't do in get_key_kworld_pc150u()
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/iio/temperature/ |
| D | adi,ltc2983.yaml | 104 This property set's the pulsed current value applied during
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/iio/temperature/ |
| D | adi,ltc2983.yaml | 116 description: Pulsed current value applied during open-circuit detect.
|
| /kernel/linux/linux-5.10/Documentation/driver-api/ |
| D | pinctl.rst | 855 pulsed out. It is likely possible to disrupt the traffic on the pin by doing
|
| /kernel/linux/linux-6.6/include/sound/ |
| D | emu10k1.h | 377 /* When writing, any write causes JOYSTICK_COMPARATOR output enable to be pulsed on write. */
|
| /kernel/linux/linux-5.10/include/sound/ |
| D | emu10k1.h | 347 /* When writing, any write causes JOYSTICK_COMPARATOR output enable to be pulsed on write. */
|
| /kernel/linux/linux-5.10/drivers/parport/ |
| D | parport_pc.c | 1043 "pulsed low, high-Z", in show_parconfig_winbond()
|
12