| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/leds/ |
| D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
|
| /kernel/linux/linux-5.10/drivers/rtc/ |
| D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| /kernel/linux/linux-6.6/drivers/rtc/ |
| D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| /kernel/linux/linux-5.10/Documentation/hwmon/ |
| D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| /kernel/linux/linux-6.6/Documentation/hwmon/ |
| D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-mt6797.txt | 59 or 3 for the advanced pull-up resistors.
61 or 3 for the advanced pull-down resistors.
|
| D | mediatek,mt6779-pinctrl.yaml | 113 Pull up setings for 2 pull resistors, R0 and R1. User can
124 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| /kernel/linux/linux-6.6/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /kernel/linux/linux-5.10/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/hwmon/ |
| D | ntc-thermistor.yaml | 12 Thermistors with negative temperature coefficient (NTC) are resistors that
59 We can use both pull-up and pull-down resistors at the same time, and then
|
| /kernel/linux/linux-6.6/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /kernel/linux/linux-5.10/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /kernel/linux/linux-5.10/arch/arm/mach-s3c/ |
| D | Kconfig.s3c64xx | 206 resistors fitted so that the card detects for
215 resistors fitted so that the card detects for
|
| /kernel/linux/linux-6.6/drivers/input/serio/ |
| D | parkbd.c | 33 * The diodes can be fairly any type, and the resistors should be somewhere
34 * around 5 kOhm, but the adapter will likely work without the resistors,
|
| /kernel/linux/linux-5.10/include/linux/platform_data/ |
| D | st_sensors_pdata.h | 20 * @pullups: enable/disable i2c controller pullup resistors.
|
| /kernel/linux/linux-6.6/include/linux/platform_data/ |
| D | st_sensors_pdata.h | 21 * @pullups: enable/disable i2c controller pullup resistors.
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/net/ |
| D | motorcomm,yt8xxx.yaml | 59 be configured with hardware pull-up resistors to match the SOC voltage
76 be configured with hardware pull-up resistors to match the SOC voltage
|
| /kernel/linux/linux-5.10/drivers/input/serio/ |
| D | parkbd.c | 33 * The diodes can be fairly any type, and the resistors should be somewhere
34 * around 5 kOhm, but the adapter will likely work without the resistors,
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/pinctrl/ |
| D | mediatek,mt6779-pinctrl.yaml | 162 Pull up settings for 2 pull resistors, R0 and R1. User can
174 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,mt6795-pinctrl.yaml | 133 Pull up settings for 2 pull resistors, R0 and R1. User can
145 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| /kernel/linux/linux-6.6/include/linux/usb/ |
| D | isp116x.h | 11 /* Enable internal resistors on downstream ports */
|
| /kernel/linux/linux-5.10/include/linux/usb/ |
| D | isp116x.h | 11 /* Enable internal resistors on downstream ports */
|
| /kernel/linux/linux-5.10/Documentation/devicetree/bindings/gpio/ |
| D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|
| /kernel/linux/linux-6.6/Documentation/devicetree/bindings/gpio/ |
| D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|